My MacBook Pro is password protected but all of a sudden the keyboard stopped functioning and I can't log in at all. What should I do? Thanks in advance.
My MacBook Pro is password protected but all of a sudden the keyboard stopped functioning and I can't log in at all. What should I do? Thanks in advance.
Get a USB key board
Similar Messages
-
all of a sudden my iphone stopped charging and you can't hear the music through my ihome iH150 when I connect it to the dock, what can I do to fix the ihome? The ihome does turn on and I already checked for dock possible problems and I don't see anything wrong.
I also have to add that the right earbud only doesn't work on my phone while i'm listening to music. If I'm face timing it's okay. what the heck.
-
However, I took some screenshots and when I went to upload the pictures to my Mac, the screenshots uploaded. So I believe my phone still is working but the screen is just not turning on. I tried holding down the home and top button for ten seconds, even longer, but nothing occurred. I am hoping to find a possible solution so I do not have to buy a new phone. Thank you!
The backlight burned out from getting it wet. You will have to replace the screen at a 3rd party shop, buy a screen and replace it yourself, or make a Genius Bar appointment at your nearest Apple Store and do an out-of-warranty replacement for $199 USD.
-
I have a WiFi system in the house that uses the Airport Extreme for a hub and an older Express for sending music from my Mac to my sound system. Everything worked great till yesterday. When I go to Networks I see the Extreme and I see the Express but the Express is no longer connected and I get an error message "this version of AirPort Utility doesn't support this base station". Any ideas?
This sounds as if you have an older AirPort Express that is no longer supported by the newer Mavericks operating system.
To check and see if that might be the case, locate the model number on the side of the AirPort Express. It will start with an "A" followed by four numbers. Hard to see in the faint print.....so you may need reading glasses or a magnifying class to see the model number clearly.
Model numbers A1084 and A1088 of the AirPort Express are no longer supported by AirPort Utility in Mavericks.
You will need to use a Mac running Leopard, Snow Leopard, or a PC to be able to administer the older AirPort Express. -
In the process of reformatting my macbook pro, I saved everything but my keyword list. The keywords are with the images, but the total list I use under "Keywords" is not present. Is there a way to re-create all my keywords I've used over the last 6 years.
I accomplished what I needed last night. I remembered I had picked my favorite images from each year and put them in a "favorite" folder by year. These folders included 500 to 1200 images per year. I pulled up the folder for each year and highlighted all images and clicked on "Keywords" and all keywords used for all images were listed. I made those keywords persistent. It took me a while to realize I had to click on each keyword to make it persistent. After doing this for all years, I assume 95% of all keywords I have used over the many years were back in my list. I'm sure there is probably a more "technical" way to accomplish what I needed, but this seems to have worked. I also exported my list into a word document and is saved on my hard drive.
If I had not made folders with my favorite images for each year, I could not have used this method, so if you figure out a better way, I like to hear it. Thanks for your comments and willingness to help. -
I use a macbook pro. Several months ago I signed up for the Photoshop/lightroom offer and the payments are taken from my bank but I am unable to locate the product. I just get a message saying that my trial is expired. I am really desperate.
Sign in, activation, or connection errors | CS5.5 and later
Mylenium -
My MacBook Pro, does not start after pushing start button. The side bar starts and stops at half way.
Hy myneck,
Happy Holidays! The resource below may provide some steps to try if your MacBook Pro won't start.
Troubleshooting: My computer won't turn on - Apple Support
http://support.apple.com/en-us/TS1367
This article discusses what to do if your Mac won't turn on. To differentiate this from a display issue, be sure that when you press the power button:
You don't hear a startup chime.
You don't hear any fan or drive noise.
There is no video on your built-in or external display
If your computer has power but doesn't display any video, it may have one or more of these similar symptoms when you press the power button:
You may hear a startup chime.
You may hear fan or drive noise.
You may see a light from the Sleep LED (if your Mac has one).
Pressing the Caps Lock key on the keyboard causes it to light.
If any of these display-related conditions occur, see Troubleshooting: My computer has no video instead. Otherwise, continue with this article.
If your computer won't turn on, try each of these steps:
Verify you have a good connection from your Mac to the wall outlet by confirming the power cord and adapter if present are securely connected and plugged in. To check if the wall outlet is working, plug in a lamp or other electrical device.
If the wall outlet is working and you continue to have no power try another power cord or adapter if available. If it works you may need a replacement cord or adapter.
Note: See Apple Portables: Troubleshooting MagSafe adapters for further troubleshooting with MagSafe adapters.
Disconnect all accessories that are plugged in to the computer, such as a printer, hub, or other mobile device.
If your Mac supports user-installable memory, solid state drive, or hard drive, and you recently installed any of these, make sure they are installed correctly and are compatible with your computer. If possible, reinstall the original memory or drive into the computer to find out if the behavior persists afterwards.
MacBook Pro: How to remove or install memory
MacBook: How to remove or install memory
Mac Pro: How to remove or install memory
Mac mini: How to remove or install memory
iMac (27-inch, Late 2012): Installing or replacing memory
iMac: How to remove or install memory
Reset the SMC.
If you are still unable to start up your computer after trying each of these steps, visit an Apple Store or Apple Authorized Service Provider (AASP) for further diagnosis. If you plan to visit an Apple Retail Store, make a reservation at the Genius Bar using http://www.apple.com/retail/geniusbar/ (available in some countries only).Note: Diagnostic fees may apply for issues not covered under warranty or the AppleCare Protection Plan (APP).
I hope this information helps ....
- Judy -
i have a problem with my Macbook Pro. When i tried to open it, something appeared : "enter your system lock PIN code to unlock this Mac". What should i do?
Question is did you lock your Mac from Find my iPhone using iCloud or is the Macbook really yours?
If you have in fact locked your Mac using Find my iPhone on iCloud then you will need to enter the PIN you have set when you locked the Mac.
*If you have not iniate the remote Lock then someone else has used your Apple ID and Password to lock your mac.
Message was edited by: Ammadz -
ipod 5th generation will not turn on, charge, or connect to macbook laptop. i was using it for music then all of a sudden the screen went black and was unresponsive. i have tried using other cords. also my home button is broken. someone please help!
Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar -
All of a sudden my iTunes stopped working, and I get the following error messages:
1. the program can't start because MSVCR80.dll is missing from your computer. Try reinstalling the program to fix this problem
and
2. iTunes was not installed correctly. Please reinstall iTunes. Error 7 (Windows error 126).
Now I've checked the forums and followed the advice of uninstalling all Apple applications, rebooting, and reinstalling iTunes.
This is not working. I've tried installing as Administrator but doesn't make any difference at all.
There must be a way to fix this? I'm not a tech geek but I want to avoid having to take my laptop back to factory settings to sort this out.
ThanksClick here and follow the instructions. You may need to completely remove and reinstall iTunes and all related components, or run the process multiple times; this won't normally affect its library, but that should be backed up anyway.
(99192) -
This is making me really mad I have an iPhone 4s and all off a sudden the volume slider disappeared and now it won't let me turn up my volume I have reset restored done the tooth brush trick blew into it and everything an it still wont work someone help!!
Is that the only solution? This just happened to me last night and I though that maybe it was just acting up and it would be fine this morning but it wasnt..
-
My iPod nano needs to be format, but it doesn't format using fat 32. And it says that it is corrupted. What should I do?
As I connect it to itunes, it shows that it needs to be format. When I try to format it (fat32) it doesn't finish. And it says, the ipod appears to be corrupted.similar to what is happening to me....the difference is, after restoring itunes detect ipod and ask to restore again and again....
I know it may look kinda stupid but: just leave the ipod there for about 2 minutes, that's about the time my itunes is taking to detect my ipod...if it doesn't work, try connecting ur ipod to other computer with itunes (no need to sync, just to check if itunes will recognize) to check if the problem is with the ipod or with the itunes and/or computer. -
Keynote is not responding. I have already worked on my slides for hours, but did not save; suddenly the application stops responding. What's the solution?
If you had never saved the file at any time, you have lost your work.
Go to; Apple Menu > Force Quit
Start a new presentation, and from now on, after adding the first object to the slide, save the file. -
Before starting AHT, be sure to disconnect all external devices except the keyboard, mouse, display, and Ethernet adapter. Also disconnect any external optical drives. What is included in these external devices?
I have tried repeatedly to use the Apple Hardware test on my iMac desktop 10.7.3 early 2009 4 GB with no luck. What am I doing wrong? I have everything I can think of unplugged. Do I need to disconnect BlueTooth in Preferences?
Thanks -
What is going on with mobile me? All I get is the find iphone screen and I can't switch apps to read mail.
MobileMe is working partially, Apple says some users can't access to the web-apps (Mail, Calendar, etc.). In my case is working fine in my iPhone, in Outlook 2010, and I can only access the Mail app (Calendar and other functions are not working!).
Hope this gets fixed soon
Maybe you are looking for
-
Problem with outer joins and the class indicator/discriminator
Hello, I am having a problem defining a query in toplink (10.1.3.3). In the workbench, I have created a parent and 2 child descriptors. The parent is "AbstractValue", the children are "DefaultValue", classified by the discriminator 'DEF', and "Overri
-
How can I re-enable the "are you sure you want to delete this email" function?
When I click delete my emails get deleted with one click. I accidentally click delete and they get lost in my trash folder often. How can I enable the "are you sure you want to delete this email" function?
-
Filling out a form scanned to PDF
Is this Possible? I would like to be able to fill out this form that I scanned to pdf...while it is still in the computer, then print it out completed so I can mail it off. I just can not seem to figure this out, please help!
-
hello there! i have installed solaris 11/06 x86 on mt toshiba satellite laptop and the OS did not found the network card --Intel Pro /100 VE and i do have dual boot of winXP on the same laptop and i explored in the XP to find out the vendor id and pr
-
Do i have to create sample database and make it production or create new database by dbca. which is the method to be used in failsafe 10.2.0. windows 2003.