My time zone will not automatically reset

I have been in South America for 2 months. Coming from the states, my time zone adjusted automatically (1 hour time difference). I spent a weekend in Uruguay and when I returned to Argentina, the time zone did not readjust to Argentina time, but stayed on Uruguayan time (another hour difference). I've tried turning on/off the automatically adjust button in the time zones section as well as restarting my computer. What else can I do to fix this?

This didn't work. I've tried turning off the phone resetting location services, turning airplane mode on and off, opening the map app (which does recognize I'm in the USA ) and I'm still on brazil time.

Similar Messages

Time capsule will not hard reset

Have a older time capsule will not reset any method. Light just keeps flashing yellow

Can you access it via the airport utility.. if so you can reset via the utility.
When you press the reset button with a paperclip or toothpick you should feel the switch.. it is fairly normal switch effect like the keyboard. If in the past you pushed too hard you have bent and jammed the lever.. so it is now broken.. the only way to fix it is to open the TC and fix the lever arm.
BTW the light always flashes yellow.. when you have done a successful reset it simply flashes faster.
The Factory Reset Gen1-4.
Unplug your TC. Hold in reset. and power the TC back on.. without releasing reset for about 10sec. When the status light flashes rapidly; release it.
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.

Time machine will not complete backup.

Time Machine will not complete back-up - 3TB back-up is full and time machine will not automatically delete oldest back-up.

This happens from time to time. You will need to step in and decide what to do.. Delete manually.. a very slow and fraught process.. or you have to take more severe action.. eg archive off the old backups and start again. You will need a 3TB USB drive to do it.. but IMHO is well worth it. Assuming you need all that history. You can then simply do a quick erase from Airport Utility which takes a minute or two and do a fresh backup.
Try to eliminate files that are not necessary to backup.. eg the worst is any virtual disk for parallels or bootcamp.. where the slightest change to the smallest file will result in a full backup of the whole virtual disk. You must backup windows etc from inside the OS and not from TM in Mac OS.
Have you upgraded the computer btw?? I get the feeling that when you upgrade a computer.. say Snow Leopard to Lion to Mountain Lion.. TM has real issues handling the old backups. It is much better to start over.
Read up from our most productive expert.. Pondini..
http://pondini.org/TM/C4.html

Ipad will not automatically set date and time

My ipad drained and when I recharged it the date read 31 Dec 1970. Now it will not automatically connect and update the date and time, and cannot connect to itunes. I can recieve emails on this device but I can's send emails. So it must have some kind of connectivity...would appreciate any comments or help. Very frustrated.

Try resetting it. Hold the on/off and home buttons together for about 10 seconds till the Apple logo appears.

2nd Gen Time Capsule - will not power up - just stopped working all of a sudden - I have tried other power outlets - I have tried pressing the reset button - no light

2nd Gen Time Capsule - will not power up - just stopped working all of a sudden - I have tried other power outlets - I have tried pressing the reset button - no light

The power supply is shot. But that it lasted even this long is the wonder.. not that it died.
The TC runs too hot..
Look on ebay for "Time Capsule power supply"
You can get a replacement and fix it although the economics are not so good.. it is probably time for a new TC.
If you can DIY it is really only a few dollars worth of capacitors that go bad.
See https://sites.google.com/site/lapastenague/a-deconstruction-of-routers-and-modem s/apple-time-capsule-repair
For a bunch of alternatives.

It is very annoying when I am at a favourite web site and Firefox will not automatically redirect to another page. It is so continuous and I have to "Allow" through the whole time I am at my favourite web sites

# Question
It is very annoying when I am at a favourite web site and Firefox will not automatically redirect to another page. It is so continuous and I have to "Allow" through the whole time I am at my favourite web sites.
Here is one of those sites:
http://conservatives4palin.com/

You can make it automatically redirect by doing this:
1. Go to: Tools > Options > Advanced > General
2. Untick the 'Warn me when websites try to redirect or reload the page' option
3. Click 'OK'
'''If this was the answer you were looking for, please click 'Solved' -- Thanks.'''

TS1398 iPad will not automatically connect to home WiFi, I have to do it manually each time.

My iPad will not automatically connect to my home wifi and I have to manually connect each time. Is there something I can do to correct this?

Update the firmware in your WiFi router. Look for an update on the manufacturer's support Web page.
If you need more help please give the make, model, and version of your WiFi router.

My iMessage and Facetime won't activate, says waiting for activation. All photos and contacts are restored, using email and wifi only, no service. Only issue is date and time will not automatically set.

My iMessage and Facetime won't activate, says waiting for activation. All photos and contacts are restored, using email and wifi only, no service. Only issue is date and time will not automatically set.

Howdy eewebe13,
So you have no cellular service but are on Wi-Fi yet iMessage and Facetime are waiting for activation.
Please step through this article for that scenario.
If you get an error when trying to activate iMessage or FaceTime - Apple Support
Thank you for visiting Apple Support Communities.
Nubz

Time Capsule will not reset

I'm trying to delete old user devices from my access control list, but after I remove them, the Time Capsule will not reset properly. After I delete one of the devices, click on Update, the time capsule gets stuck during the update and never fully resets. If I pull the plug and restart the time capsule, it reverts back to it's previous state with the devices still in the access list. Is anyone having this trouble?

Dear Stephen,
I have the same problem and I found this thread describing the same thing on another forum. Each time I try to change any setting this happens (i.e., TC won't reset and I have to unplug it before I can use it again).
When the postings in the mentioned thread are any indication no reset (hard or soft) will have any lasting effect. But of course, I will try to reconfigure and see what happens.
Any solution or localization of where the source of the problem (firm-/soft-/ or hardware) would be highly appreciated:)
Best
Rene

My iPhone 5 will not automatically connect to my home wifi

My wifes iPhone 5 will not automatically connect to our home wifi, she has to log in each time (she has ios 6.1.4). Mine, however will connect automatically with no issues (we have same phone and ios). Here is what I have done so far to fix the issue and none have worked:
* I have reboted (hold home button and sleep/wake button)
* I have reset the network connections
* I have turned "ask to join" on, connected to the network, turned wifi off and then back on, it did not connect to the wifi
* I have manually connected to the network through the manual option, turned wifi off and then back on, it did not connect to the wifi
* I have erased all content and data and resored the backup from iTunes
* I have restored iPhone from iTunes and restored the backup from iTunes
My phone does not list a "forget this network" as an option on the wifi connection when I pull it up, so this is not an option. So, what else is there to fix the issue?

Hi there Huskerscott!
I have some information here that can help you troubleshoot this issue:
Unable to automatically connect to Wi-Fi
Avoid giving your Wi-Fi network a common name.
Some wireless routers are preconfigured with a common SSID (network name) such as "wireless" or "default."
If your desired Wi-Fi network has a common SSID, try changing the SSID to something unique2.
If your desired Wi-Fi network has a unique SSID, reset network settings by tapping Settings > General > Reset > Reset Network Settings.
Note: This will reset all network settings including: previously connected Wi-Fi networks and passwords, recently used Bluetooth accessories, VPN and APN settings.
Which is taken from this article:
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/ts1398
It also may be helpful to follow these settings, which are optimal for use with iOS and OS X devices:
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/ht4199
Thanks for being a part of the Apple Support Communities!
Regards,
Braden

Encoder position not automatically resetting on z pulse

I am using a PCI-7344 motion control card with a UMI-7764 break out box. Connected to this is a Pepperl & Fuchs 1024 line encoder.
Problem 1
The encoder counts up and down ok but gives 4096 counts between z pulses and not 1024.
Problem 2
The position does not automatically reset to zero when the z pulse is seen.
The encoder connections have been checked via oscilloscope for correct relationships (z is high when A and B are both low), but when mapping the encoder signals to RTSI signals and monitoring them, the signals are inverted.
I've tried a lot of combinations of polarity and phasing but all to no avail. What's going on??!
Attachments:
Encoder_test.vi ‏42 KB

1. The 7344 rather counts quadrature signals and so the number of pulses it will count will always be 4 times the number of encoder lines. On all encoders I have seen just the number of encoder lines per revolution is specified.
2. Unless you are using a Find Index command the 7344 won't reset the encoder pulse counter. There is more than one application where the encoder will make several turns during a full motion cycle - remember a geared drive or a worm gear drive. If the motor/encoder has to make more than one revolution to complete its motion cycle resetting the pulse counter each time the index pulse occurs would be quite disturbing.
AFAIK with the latest firmware/software version it is no more necessary that both A and B are low when the index pu
lse occurs, you can set the actual state of A and B when index occurs with a special command.
BTW in cases the encoder/motor will make several revolutions you should use a separate home switch to detect proper zero position of the drive, of course using the Find Home command. It can be combined with (or rather followed by) a Find Index command to detect the zero position more precisely.

My iPhone will not automatically backup to iCloud after iOS7 install

My iPhone 5 will not automatically backup to icloud anymore now that iOS7 has been installed. Steps I have tried so far...
Installed iOS7 through Software Update - relazed three days later that the phone was not backing up
Did a manual backup
Erased the entire phone
Restored from iCloud backup
Then reset all phone settings
Signed out of iCloud, deleted all data and then signed back in
Is anyone else having this issue after updating to iOS7?

my dear friend i have like your problem before and when i see alot of solution i find the one it work with me and
come autmatic again
take the solution:
Note that a manual backup also factors into the automatic backup schedule, meaning the next automatic backup will not occur until 48 hours later.
Actually the iCloud backup process sounds a bit more complicated than it actually is in practical use. You can’t schedule iCloud backups manually, but you don’t need to do so as iOS takes care of this for you, and it’s designed to be pretty transparent.
Once enabled, iCloud backups will run automatically whenever the following conditions are met:
Your device is powered on,
Your device is connected to the Internet via Wi-Fi,
Your device is connected to a power source,
Your device has the screen locked (i.e. turned off), and
It has been at least 24 hours since the last successful backup occurred.
In other words, your device may not be backed up to iCloud at the same time every day, but once 24 hours has elapsed the iPhone will make a backup as soon as it is plugged in and on Wi-Fi with the screen off. For example, if your iPhone backs up to iCloud at 10:00 pm tonight, but you don’t plug it in while on a Wi-Fi connection until midnight tomorrow night, the next backup will occur at midnight—basically as soon as you plug it in—and future backups will continue to run at midnight on subsequent days as long as the iPhone is plugged in, connected to Wi-Fi, and has the screen off at that time. If you’re working an irregular schedule and coming home at different hours, this may gradually push the backups to later at night, but the backup won’t be skipped if you miss the time window—it will still occur as soon as possible once all of the other conditions are met.
This does of course mean that sometimes backups can get pushed to the point where they may be delayed until the next night; come home at 10 a.m. on a Sunday morning and plug in your iPhone and that’s when your next backup will occur, but if you leave for work on Monday morning at 9:00 am and your phone isn’t plugged in and on Wi-Fi while at work, you won’t get another automatic backup until you get home and plug it in later that night.
You can check the time of the last successful iCloud backup by going into the Settings app on your iPhone and choosing Storage & Backup from the iCloud section.
You can also tap the “Back Up Now” button from this screen to create a manual iCloud backup at any time. To create a manual iCloud backup, your iPhone only needs to be on Wi-Fi, it does not need to be plugged in or have the screen off.
Note that a manual backup also factors into the automatic backup schedule, meaning the next automatic backup will not occur until 48 hours later.
This can be one method for adjusting to a specific backup time if you really feel the need to, but it’s largely unnecessary as iOS should naturally settle into a standard backup routine as long as your iPhone is regularly plugged in and on Wi-Fi for at least a few hours each day, such as while you’re sleeping.
As one last note, it’s also worth keeping in mind that the iPhone only needs to be connected to power with the screen off to start an iCloud backup; once the automatic backup has started, it will continue as long as the iPhone remains on a Wi-Fi connection, even if you unplug the iPhone or begin using it.

Ever since I had updated my phone to ios 6, i noticed that it no longer saved photos to my camera roll. If i download a picture on on an app, it will not automatically save it to my camera roll as it used to do, nor does it save any image

Ever since I had updated my phone to ios 6, i noticed that it no longer saved photos to my camera roll. If I take a picture on Instagram, it will not automatically save it to my camera roll as it used to do, nor does it save any image, I just want it fixed.

To gdgmacguy your a f****** idiot for one I'm having the same problem as pennymar. And you tell me to quit whinning. You got more problems then the iOS 6 you did not answer my question nor the other 13 or whatever you replied to within a 30 min time frame. You must got nothing better to do then to harass people and to pretend you know something about apple products. Which you don't from what I've read the other advices you should have gave to other people. But you didn't you replied a question back to the people asking a question. So if your not gonna use these community forums the right way don't use them at all.

Time machine will not back up to time capsule

Time machine will not back up to my Time Capsule on my MacPro running SnowLeopard. Error message says it cannot access the backup file. I have reset the TC, and erased the drive and I get the same error on initial backup. I can see the volume and drag files to it, so the disk appears OK. What's going on here?

Depending on exactly what message you get, you might need #C17 in Time Machine - Troubleshooting
If not, please post the message (a screenshot would be fine).

Why will images will not automatically load in apple mail despite having the setting turned on correctly

I have had this ongoing problem. I cannot get images to automatically load in mail. Instead I always have to click the load images button. I click on a message, click load images, the images load. I click on another message, then back to the message with the images and have to reload them.
In preferneces I have turned the View>Load remote HTML images on and off and on again, and rebotted multiple times. It makes no difference. The images do not load.
I checked Little Snitch, but all ports are open.
My firewall is set to let everything connect to mail. Even just turning off the firewall does not solve the problem.
I tried removing com.apple.mail.plist but that did not work either.
This problem occurs in Mail on a MacBook Pro and on a MacBook Air both using the newest version of OS Mountain Lion. The problem happened in OS Lion as well.
The senders are in my contacts, so that doesn't help either.
This is not an issue with the serve sending the images. The images load if I click load images. They just will not automatically laod.
I've read tons of posts but no one seems to know how to solve the problem.
Does anyone have any other ideas?

I am not sure how to link these discussions, so below I am pasting the post that helped me. And here is the link:
https://discussions.apple.com/message/15733241#15733241
louse101
Jul 25, 2011 3:17 AM
This is not a problem specific to Lion, but most recent OS X versions. Regularly I receive email formatted as HTML, which includes JPEG images embedded within them. These images are technically attachments, and as such, Mail.app displays them as a placeholder. Other mail apps will display these images inline, regardless of them being an attachment, remote image or otherwise.
How can I make these images load automatically?
MacBook, Unibody, Mac OS X (10.7), 750GB, 7200RPM WD HDD, 4GB RAM
This solved my question by louse101 on Jul 26, 2011 3:47 AM
No-one replied, but I found a solution on another board. Run Terminal (do a Spotlight search if you don't know where to find this), and type:
defaults write com.apple.mail DisableInlineAttachmentViewing -bool false
This will force Mail not to disable inline attachment viewing. Obviously, to reverse this, simple replace 'false' at the end with 'true'.
See the answer in context

My time zone will not automatically reset

Similar Messages

Maybe you are looking for