TS1398 iPad will not automatically connect to home WiFi, I have to do it manually each time.

My iPad will not automatically connect to my home wifi and I have to manually connect each time. Is there something I can do to correct this?

Update the firmware in your WiFi router. Look for an update on the manufacturer's support Web page.
If you need more help please give the make, model, and version of your WiFi router.

Similar Messages

  • TS1398 my iphone 5 will not automatically connect to known wifi

    i just got the new iphone five. i connected to my home wifi with no problem. when i leave and come back the phone will not automatically connect to the wifi. i have no problem's with my wife's iphone or the ipad. i went to sprint store they were no help. any suggestions?

    I downloaded and installed the latest software for the iPhone 5 (Version 6.1.3) - the version originally installed was 6.1.2.  Same problem exists - iPhone will not automatically connect to my home WiFi.  Even after I select my network and it connects.  If I turn WiFi off and then back on again, it will not automatically connect.  The iPhone screen states "Known networks will be joined automatically.  If no known networks are available, you will have to manually select a network."  How do I get the iPhone to work as specified above?  Thanks.

  • Airport Extreme Card (will not automatically connect to home network)

    Running OSX (10.4.7) on a G5 2.0 DualCore. I just had an Airport Extreme Card installed by Apple a week ago. Everything was working fine with WiFi ( I use a Lynksys Router. But oddly now when I cold boot up, the Airport Extreme will not automatically connect to my home network. The little Airport icon on the upper right is always greyed out ( even though clicking on the icon... says that Airport is "On" ). So I now have to manually select my home network everytime I boot up. The first week or so though, I didn't have to do this...it just automtically connected to my home network. I made no changes to the router settings, nor the Network prefs.

    I have been able to get my home network running with simultaneous access to the internet with the MacMini and the PB G4 via a WL router (Netgear WGR614v4 with four ethernet ports).
    This was the process:
    1a) Turned off airport on both computers.
    1b) Turned off both compters and
    1c) disconnected the router from the cable modem.
    a) Disconnected ethernet cable from WL router to Macmini.
    2b) Powered down the router for 10 seconds.
    3a) Keeping both computers unpowered,repowered router and pressed the reset button (behind an unmarked tiny hole in the back of the router) then re-connected it to cable modem. Waited 30 - 40 seconds until internet service lights flickered green.
    3b) Reconnected ethernet cable to MacMini and turned on power for MacMini. No Airport running. With administrator privilege I configured in Syst. Prefs. "Sharing" folder Internet access using "Built in Ethernet" port for computers running "Airport".
    4) Turned Airport network on in MacMini and started browser.
    Result: Internet connection established.
    5a) Powered up PB G4 and then turned Airport on.
    5b) In Syst. Prefs. in "Sharing" folder turned Internet Sharing off. But set "Share your connection from Airport" to computers using: Airport with check-mark. (No Built-in Ethernet and no Built-in FireWire!)
    5c)Started browser. Result: Internet connection established.
    6a) In the Finder window of both computers I clicked on "Go" in toolbar and looked for the name of the other computer, which were listed as alias besides the "Library" and "Servers" aliases. Clicking on the computer alias brought up the 'Networked Globe' and a control button "Connect".
    6b) Clicking on "Connect" brought up the mounted drive of the other computer.
    Result: Wireless network operational.
    PS: I don't dare yet using encryption for the airport network. That's for another day.
    Power Book G4, MacMini   Mac OS X (10.4.7)  

  • HT1222 Since I downloaded my update my iPad will not stay connected to the wifi. Why? & how can I fix it?

    SInce I downloaded the new iOS6 update on my ipad2, it will not stay connected to my wifi. Does anyone know why or how to fix it?

    Hm, posting on this forum didn't fix it for me. 

  • IMac will not automatically connect to my wifi network

    iMac is 21.5, mid 2011, running OSX Lion 10.7.5.  AirPort express is 2nd Gen version 7.6.3. It will not save a preferred network, so I have to select my network every time.

    open advanced menu of your wifi after connect to your wifi..............
    then
    check remember networks this computer has joined.......
    thn click ok ....
    if this is not work for u try assist me... option in network menu
    then click on diagnostics option and follow the intractions.......
    m sure  this will halp u.....

  • IPhone 5 not automatically connecting to home wifi.

    I passed on my iPhone 5 to my son, he's still with the same network as me but it is not connecting to the home wifi, whereas I have a strong connection on my iPhone 6 and iPad. He is lucky to get 3G, most of the time it is only GPRS. I have tried reseting the network settings but makes no difference, help please?

    Try to reset the phone by holding the sleep and home button for about 10sec, until the Apple logo comes back again. You will not lose any data by resetting, but it can cure some glitches.
    If this does not help, setting it up as new device would be the next step:
    How to erase your iOS device and then set it up as a new device or restore it from backups
    Or, if you want to use your computer and iTunes instead:
    Use iTunes to restore your iOS device to factory settings - Apple Support

  • 2013 Macbook Pro will not reliably connect to home WiFi.

    This problem began about a month ago.  I've owned this computer for 2 months and had no problem the first month.  Now, when I turn it on it searches for the wifi signal and my wifi's SSID is visible but it doesn't connect, even when I select it from the list. It stops searching and the ! icon appears.  If I restart the computer it will usually connect then automatically but at times I've had to restart it 2 or 3 times before this happens.  And it can happen multiple times each day if I shut down the computer.  At times though it works normally so the problem is intermittent.  My Iphone 5 has no problem connecting with my router.  I believe this began happening about the time I added a Brother wireless printer.  I also now occassionally get a message that there are 2 devices sharing the same IP address and don't know what that's about or if it's related to the problem.  This is my first Mac (and first wireless printer) and I should also add that I consider myself a technodummy.  Help in solving this perplexing and annoying problem would be greatly appreciated.

    This problem began about a month ago.  I've owned this computer for 2 months and had no problem the first month.  Now, when I turn it on it searches for the wifi signal and my wifi's SSID is visible but it doesn't connect, even when I select it from the list. It stops searching and the ! icon appears.  If I restart the computer it will usually connect then automatically but at times I've had to restart it 2 or 3 times before this happens.  And it can happen multiple times each day if I shut down the computer.  At times though it works normally so the problem is intermittent.  My Iphone 5 has no problem connecting with my router.  I believe this began happening about the time I added a Brother wireless printer.  I also now occassionally get a message that there are 2 devices sharing the same IP address and don't know what that's about or if it's related to the problem.  This is my first Mac (and first wireless printer) and I should also add that I consider myself a technodummy.  Help in solving this perplexing and annoying problem would be greatly appreciated.

  • My iPhone 5 will not automatically connect to my home wifi

    My wifes iPhone 5 will not automatically connect to our home wifi, she has to log in each time (she has ios 6.1.4).  Mine, however will connect automatically with no issues (we have same phone and ios).  Here is what I have done so far to fix the issue and none have worked:
    * I have reboted (hold home button and sleep/wake button)
    * I have reset the network connections
    * I have turned "ask to join" on, connected to the network, turned wifi off and then back on, it did not connect to the wifi
    * I have manually connected to the network through the manual option, turned wifi off and then back on, it did not connect to the wifi
    * I have erased all content and data and resored the backup from iTunes
    * I have restored iPhone from iTunes and restored the backup from iTunes
    My phone does not list a "forget this network" as an option on the wifi connection when I pull it up, so this is not an option.  So, what else is there to fix the issue?

    Hi there Huskerscott!
    I have some information here that can help you troubleshoot this issue:
    Unable to automatically connect to Wi-Fi
    Avoid giving your Wi-Fi network a common name.
    Some wireless routers are preconfigured with a common SSID (network name) such as "wireless" or "default."
    If your desired Wi-Fi network has a common SSID, try changing the SSID to something unique2.
    If your desired Wi-Fi network has a unique SSID, reset network settings by tapping Settings > General > Reset > Reset Network Settings.
    Note: This will reset all network settings including: previously connected Wi-Fi networks and passwords, recently used Bluetooth accessories, VPN and APN settings.
    Which is taken from this article:
    iOS: Troubleshooting Wi-Fi networks and connections
    http://support.apple.com/kb/ts1398
    It also may be helpful to follow these settings, which are optimal for use with iOS and OS X devices:
    iOS and OS X: Recommended settings for Wi-Fi routers and access points
    http://support.apple.com/kb/ht4199
    Thanks for being a part of the Apple Support Communities!
    Regards,
    Braden

  • TS1398 After leaving a wi-fi connection my iphone will not automatically connect to the internet via the 3G network unless I turn it off and then on again. Is there a setting that can be changed to overcome this issue?

    After leaving a wi-fi connection my iphone will not automatically connect to the internet using a mobile 3G network unless I turn my phone off and then back on again. Is there a setting that can be changed to overcome this?

    Then I'm at a loss. Mine has switched automatically from the start, favoring Wi-Fi, any of its registered networks, whenever available. Only thing I can think of is trying a Force Restart and see if that clears things up: hold down Home and Sleep till the screen goes black and a white Apple logo pops up. Release and allow it to restart.
    May be similar, when I got the i5 about 16 months ago, the local carrier was starting to roll out 4G service. The phone would regularly lose all carrier connection, voice and data. Haphazardly would reconnect when it felt like it afterwards. Initially did the Off/On dance to speed things up, but discovered that using Airplane Mode would do the same without the lengthier power cycle. After awhile, the carrier 'fessed they were having capacity issues and later the problem went away. So yours too may also be a carrier issue.

  • Ipad will not automatically set date and time

    My ipad drained and when I recharged it the date read 31 Dec 1970.  Now it will not automatically connect and update the date and time, and cannot connect to itunes.  I can recieve emails on this device but I can's send emails.  So it must have some kind of connectivity...would appreciate any comments or help.  Very frustrated.

    Try resetting it.  Hold the on/off and home buttons together for about 10 seconds till the Apple logo appears.

  • PC will not automatically connect to wireless network on startup...

    Hi all - I have a WRTG54 wirless router with the latest firmware.  Windows XP Home SP2.  I have a mixed network with two wired PCs and one wireless.  The wireless PC will not automatically connect to the network. To connect to the network i have to go to the wireless network properties box and check "let windows automatically configure network"  Once I do this the wirelss PC connects with no problem.  Unfortunatley, whenever i turn the PC off and turn it back on the "let windows automatically configure network" is unchecked and i have to go through the process of checking it again.  I uninstalled the wireless adapter and reinstalled the drivers only and then ran the windows wireless setup wizard but the problem persists.  Any help on this would be much appreciated.!!!! Thanks!!

    First of all, give your network a unique SSID. Do not use "linksys". If you are using "linksys" you may be trying to connect to your neighbor's router. Also set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
    Do not let "Windows automatically configure your network".  Instead do the following:
    Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use.  Delete your current network (this will remove any old settings).  Reboot computer.  Return to "Preferred Networks" and re-enter your current network info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings".  Reboot computer.  It should connect automatically.  If you still have trouble, in the computer, temporarily disable your software firewall, including Windows Firewall, and see if that helps. 
    Some users have reported improved wireless connections by switching to WPA  ( = WPA with TKIP)  encryption.

  • HT1414 My iPad will not progress past the home screen. My computer will not let me back it up. What can I do?

    My iPad will not progress past the home screen, and my computer doesn't allow me to download my data from it. What do I do? I wanted to try to restore it, but I don't want to lose my "stuff".

    First, try a system reset.  It cures many ills and it's quick, easy and harmless...
    Hold down the on/off switch and the Home button simultaneously until you see the Apple logo.  Ignore the "Slide to power off" text if it appears.  You will not lose any apps, data, music, movies, settings, etc.
    If the Reset doesn't work, try a Restore.  Note that it's nowhere near as quick as a Reset.  It could take well over an hour!  Connect via cable to the computer that you use for sync.  From iTunes, select the iPad/iPod and then select the Summary tab.  Follow directions for Restore and be sure to say "yes" to the backup.  You will be warned that all data (apps, music, movies, etc.) will be erased but, as the Restore finishes, you will be asked if you wish the contents of the backup to be copied to the iPad/iPod.  Again, say "yes."
    At the end of the basic Restore, you will be asked if you wish to sync the iPad/iPod.  As before, say "yes."  Note that that sync selection will disappear and the Restore will end if you do not respond within a reasonable time.  If that happens, only the apps that are part of the IOS will appear on your device.  Corrective action is simple -  choose manual "Sync" from the bottom right of iTunes.
    If you're unable to do the Restore, go into Recovery Mode per the instructions here. You WILL lose your "stuff" with Recovery Mode.

  • My ipad will not power on after update. I have tried connecting to computer which doesn't recognize it. I have pushed top and circle buttons at same time. It had a battery charge before it died.  I tried to stop the upload and am afraid it 'crashed'

    My first genteration ipad will not power on after update. I have tried connecting to the authorized computer which won't recognize it - does not acknowledge a device is plugged in. I have pushed top and circle buttons at same time. It had a battery charge before it died.  I tried to stop the upload midway and am afraid it 'crashed'

    Try putting it into recovery mode.
    Connect iPad to your computer via USB while it's turned on.
    Open iTunes
    Hold the iPad's Sleep/Wake switch (power button on the top of the iPad) down until the "power off" slider appears.
    Power off the iPad completely (wait for the progress spinner to disappear).
    Hold the Sleep/Wake switch AND the Home button down for a full 10 seconds.
    After 10 seconds (the second time you'll see the Apple logo on the screen) release the Sleep/Wake switch while still holding the Home button.
    Continue to hold the Home button for another 10 seconds until the USB connection image appears on the iPad's screen, then release the Home button.
    A pop-up message will appear on iTunes saying it has detected an iPad in recovery mode, you must restore...
    Click on the "Restore" button and the process will begin.

  • My Iphone 5 will not automatically connect to my wireless network

    Each time I want to connect my home wireless, I need to go into settings and manually connect,  rather than automatic connection, which is what happened with my i4s.  How can I change this?

    I downloaded and installed the latest software for the iPhone 5 (Version 6.1.3) - the version originally installed was 6.1.2.  Same problem exists - iPhone will not automatically connect to my home WiFi.  Even after I select my network and it connects.  If I turn WiFi off and then back on again, it will not automatically connect.  The iPhone screen states "Known networks will be joined automatically.  If no known networks are available, you will have to manually select a network."  How do I get the iPhone to work as specified above?  Thanks.

  • My iPad will not auto-connect to my network. I need to type in a security key each time. Is there a way aound this?

    my iPad will not auto-connect to my network. I need to type in a security key each time. Is there a way aound this?
    Thanks

    Some things to try first:
    1. Turn Off your iPad. Then turn Off (disconnect power cord for 30 seconds or longer) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
    2. Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
    3. Change the channel on your wireless router (Auto or Channel 6 is best). Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    4. Go into your router security settings and change from WEP to WPA with AES.
    5.  Renew IP Address: (especially if you are droping internet connection)
        •    Launch Settings app
        •    Tap on Wi-Fi
        •    Tap on the blue arrow of the Wi-Fi network that you connect to from the list
        •    In the window that opens, tap on the Renew Lease button
    ~~~~~~~~~~~~~~~~~~~~~~~~~
    iOS 6 Wifi Problems/Fixes
    How To: Workaround iPad Wi-Fi Issues
    http://www.theipadfan.com/workaround-ipad-wifi-issues/
    Another Fix For iOS 6 WiFi Problems
    http://tabletcrunch.com/2012/10/27/fix-ios-6-wifi-problems-ssid/
    Wifi Doesn't Connect After Waking From Sleep - Sometimes increasing screen brightness prevents the failure to reconnect after waking from sleep. According to Apple, “If brightness is at lowest level, increase it by moving the slider to the right and set auto brightness to off.”
    Fix For iOS 6 WiFi Problems?
    http://tabletcrunch.com/2012/09/27/fix-ios-6-wifi-problems/
    Did iOS 6 Screw Your Wi-Fi? Here’s How to Fix It
    http://gizmodo.com/5944761/does-ios-6-have-a-wi+fi-bug
    How To Fix Wi-Fi Connectivity Issue After Upgrading To iOS 6
    http://www.iphonehacks.com/2012/09/fix-wi-fi-connectivity-issue-after-upgrading- to-ios-6.html
    iOS 6 iPad 3 wi-fi "connection fix" for netgear router
    http://www.youtube.com/watch?v=XsWS4ha-dn0
    Apple's iOS 6 Wi-Fi problems
    http://www.zdnet.com/apples-ios-6-wi-fi-problems-linger-on-7000004799/
    ~~~~~~~~~~~~~~~~~~~~~~~
    How to Fix a Poor Wi-Fi Signal on Your iPad
    http://ipad.about.com/od/iPad_Troubleshooting/a/How-To-Fix-A-Poor-Wi-Fi-Signal-O n-Your-iPad.htm
    iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    iPad: Issues connecting to Wi-Fi networks  http://support.apple.com/kb/ts3304
    WiFi Connecting/Troubleshooting http://www.apple.com/support/ipad/wifi/
    How to Fix: My iPad Won't Connect to WiFi
    http://ipad.about.com/od/iPad_Troubleshooting/ss/How-To-Fix-My-Ipad-Wont-Connect -To-Wi-Fi.htm
    iOS: Connecting to the Internet http://support.apple.com/kb/HT1695
    iOS: Recommended settings for Wi-Fi routers and access points  http://support.apple.com/kb/HT4199
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
    Connect iPad to Wi-Fi (with troubleshooting info)
    http://thehowto.wikidot.com/wifi-connect-ipad
    Fix iPad Wifi Connection and Signal Issues  http://www.youtube.com/watch?v=uwWtIG5jUxE
    Fix Slow WiFi Issue https://discussions.apple.com/thread/2398063?start=60&tstart=0
    How To Fix iPhone, iPad, iPod Touch Wi-Fi Connectivity Issue http://tinyurl.com/7nvxbmz
    Unable to Connect After iOS Update - saw this solution on another post.
    https://discussions.apple.com/thread/4010130
    Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
    ~~~~~~~~~~~~~~~
    If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
     Cheers, Tom

Maybe you are looking for

  • How to update one table from another

    I am creating scripts in Oracle 10g. I have a table that has data corruption on three date fields. I created a table with the following sql of all the affected rows: CREATE TABLE LSU_INTER_FIX_DATE AS select request_id,received_date,planned_start_dat

  • Pages 5.1 Fluctuates between 0.6% CPU & 100% CPU

    I have only used Pages a few times.  I recently got iWork when I upgraded to Mavericks.  I designed a template that looks exactly like a college ruled notebook so I can visualize ruled pages.  There are about 36 objects, which are a set of GROUPED &

  • How can I upgrade from iPhoto 6 using SnoLeopard?

    I'm trying to create a slideshow for my aunts memorial service and I am realizing that my iPhoto 6 (v. 6.0.6) is severely out of date. I'm using OS X 10.6.8 I tried going to upgrade to iPhoto 11 but when I do, it's saying that I need OS X 10.7.4 in o

  • Printer setting

    Dear Team, When I giving the printing to the printer . It ask about witch printer . i.e Output Device Spool Control : Print Immediatelly                     :Delete after output                     :New spool request                      :Close spool

  • Master Data -- unable to delete the request

    I loaded master data for 0EMPLOYEE info object, all the records Added but the request is in Read, I am trying to QM status Green Manually it is giving the message “QM action not allowed for DTP requests in master data and Text Tables “. I am unable t