Need Help In BGP Design-Multihomed

Hi,
I have a public ip pool for my servers to be on internet and I have a internet connectivity from 2 ISPs.
I want to achieve following:
1.I want to advertise my public block on the internet.
2.I want internet connectivity from both isp but in primary/secondary manner.
3.I dont want to receive bgp routing table from both isp.
Kindly help with the config required on my end

Hi,
Couple of questions..
1.Your ISP supports BGP?
2. You have /24 subnet? If not check with your ISPs first as most ISPs does not advertise subnets lless than /24.
3.Try to get your own Autonomous system number (AS#) from ARIN. If not, some ISPs work with private AS# as well.
Check the below links for different scenarios..
http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/23675-27.html
http://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/13762-40.html
hth
MS

Similar Messages

Need Help for Page Design Technique: Level 0 Record and Level 1 Record

Folks,
Hello. I am developing HR system for a client. I design a page for "Position Information" as follows:
Level 0 record fields:
Position Number: 01
Status: Open
Because many people are in this position, level 1 record is a scroll area containing many rows belong to this Position Number as follows:
Level 1 record fields:
Profile ID: 001 effective date: xx/xx/xxxx
Profile ID: 002 effective date: xx/xx/xxxx
After save the page into Database, the data in Level 1 record table doesn't match the data in Level 0 record table.
No way to identify the rows of data in Level 1 record table belong to a specific row of data in Level 0 record table.
I need help to design the Database, that is 2 tables: many rows in second table belong to one row in first table.
Can any folks give some idea to design such a Database so that save the Page correctly ?

Table 2 should have all the key fields from Table 1, followed by atleast one more key of its own.
Subhash

Need help in voip design

hi,
our customer having nearly 30 branches. 20 are connected to central office via leased lines.
And 10 branches are connected by internet.
Now customer willing to use voip on all these branches.
That is From central office to leased line offices and internet offices vice versa..
And there are analog phones with PBXs.
present along with them soft and hard IP phones are required with redundancy.
so anybody can help me in designing this voip setup? (designing means what are the required equipments and protocols for this setup)
Regards
skrao
Regards
skrao

Skrao,
Several ways to go here I don't really recommend the VOIP over the internet but your going to have to do a user count and peak call utilzation survey for each site.
Your probably going to go with one of the ASxxxx models for the central site and 2800 or 1800 for the remote sites. As for the VPN offices you might try CME Call Manager Express for them or keep there existing PBX's kinda depends on what there Goals are.
I can't give you specific parts because there is such a huge combination of different ways to go but your gist is you'll probably have a couple of Access-Servers to handle your primary site PSTN connections and then put something that can handle SRST Survivable Remote Site Telephony at each branch office. For your VPN sites your going to want to use Call Manager Express.
Patrick

Need Help Please - Data Design

Hi,
I have flow from Data Source to DSO and to cube.
The cube has 3 master data fields. 0employee, 0orgunit and 0gender. ( 0employee is having attributes 0orgunit and 0person )
0person is time dependent and 0gender is attribute of 0person.
I cant use any of 3 fields in DSO or datasource and until DSO nothing should be changed.
Now 0employee is mapped with a field from DSO. I have to get data for 0orgunit and 0gender.
Clients says to use infosource between DSO and Cube to read meta data for 0person and then use 0orgunit and 0gender as navigational attributes in cube.
I dont understand what they mean by this. At the end we need data for 0orgunit and 0gender in cube.
Also client say " 0PERSON is a time depended and you've to put the due date. For Data from actual year it would be current day, and for the "historical" ones use field_x an auxillary field in the InfoSource might help there " What do to for this?
Please help
Regards
Zabi
Edited by: Syed786 on Sep 12, 2011 11:52 AM
Edited by: Syed786 on Sep 12, 2011 12:14 PM
Edited by: Syed786 on Sep 12, 2011 6:08 PM

Hi Frank,
I'm creating some SEM Management Cockpit, the problem I faced is not the BEx Query itself, but the pie chart design and display. I have processed my data in advance, so there a only 5 values in my query at a time, and these area values are not constant values. If I don't mark a selection criteria, it will display a full pie in Management Cockpit.
And if I browse the query in IE directory, I can get a desired pie chart by "Swap Axes", so I think maybe there is a same choose in Management Cockpit.
Thank you and Best Regards,
Rocket

I need help retrieveing cs3 design standard product key

I purchased 2 adobe cs3 design standard in 2008. The purchase was made from new egg. I have a copy of the invoice. Need to get the product key. Can you help?

We can't help you. This is a user forum and we can't help with product key/ registration numbers/ etc.
You need to use Adobe Chat to talk to an Adobe rep:
Contact Customer Care

Need help re: authentication design

Hi all.
I'm designing an app from the ground up on 9i+HTMLDB (yay!), but am still climbing the learning curve WRT all the authentication issues, especially where database links are involved.
I've tried to piece together an understanding from posts here, from asktom, from docs, etc... but am still a bit fuzzy.
We're not committed to any particular authentication mechanism yet, but I'd like to take advantage of VPD/FGAC, auditing, and all the other stuff that having "real" database users gives you.
(If it helps to know: as far as I know OID authentication IS an option in our environment.)
HTMLDB will reside on one machine (A), fetching data from another machine via database links (B). I believe the HTTP server will be on yet another machine (C). I don't really have control over this.
I need a "best practice" here for having VPD work in this scenario.
My thoughts so far:
1. Set up the HTMLDB DAD with no default username/password, which would prompt the user to login via basic authentication. I'd also set up my dblink without a default username/password, so that authentication from the HTMLDB login will get passed to the linked db. Is that right?
2. Create views in A to wrap access to tables in B, e.g. "create view t as select * from t@B" (Certainly makes HTMLDB's wizard-driven development easier.)
3. Apply policies to base tables on B.
I'm unclear about where to set sys_context, and what object permissions I'll need to set on the views in A.
Help! Many thanks.
-John
PS: sorry for the repost. I sent this last night, and for some reason it got posted with an Aug 2001 timestamp. weird.

John,
We should have a VPD how-to published on OTN any day now. Send us your email address (to [email protected]) and we'll send you a draft.
To address some of your questions lightly:
- You don't need any database accounts for your users. Setting the sys_context with the name of the authenticated user is the key.
- You'll use the same DAD you use now, which connects as a generic public user.
- I strongly recommend that you create views, dblinks, policies, etc., using SQL*Plus and try out a few scenarios with your schema. Then you'll learn what privileges you need on base tables vs. views, etc. Once you get the components working, using them from within an HTML DB application is simple.
- Search this forum for VPD for related discussions.
Scott

Need help with class design

I want to design and use one or more classes for a particular project I am working on.
I need some advice hopefully from someone who has experience in this area. Basically,
for this particular problem I have two database tables. I want the first class to
represent the first database table and the second class to represent the second
database table. An object of the first class will be created first, and then if certain
criteria are met then an object of the second class will be created.
Question:
Should I use classical inheritance and let the first class inherit from the second class?
Or should I use the containment delegation model and embed an object of the second
class in the first class?
----Tables------
For example, my first table ET_UserData looks something like this:
ET_UserData
(PK)UserName
Password
FirstName
LastName
My second table ET_DetailedUserData looks like this
ET_DetailedUserData
(FK)UserName
WorkAddress
WorkPhoneNumber
CityWhereEmployed
SocialSecurityNumber
City
State
StreetAdress
PrimaryTelephoneNumber
AlternatePhoneNumber
HasRegistered
RegistrationDate
RegistrationTime
CreditCardNumber
NameOfPrimaryContact
DateOfBirth
Weight
EyeColor
Height
Member
Here is are some pseudo classes for the two classes.
Class UserData
string UserName
string FirstName
string LastName
Class DetailedUserData /* For a classical approach, sub class off of class UserData */
/* UserData ThisUser --> Containment delegation model */
string (FK)UserName
string WorkAddress
string WorkPhoneNumber
string CityWhereEmployed
string SocialSecurityNumber
string City
string State
string StreetAdress
Int PrimaryTelephoneNumber
Int AlternatePhoneNumber
Bool HasRegistered
Int RegistrationDate
Int RegistrationTime
Int CreditCardNumber
String NameOfPrimaryContact
Int DateOfBirth
Int Weight
Int EyeColor
Int Height
bool Member
}

Thank you for your help. If you can continue to help me I would appreciate it.
I and another developer did the database design. Pretty solid design. Plus we have all of the requirements
which are very good too.
Originally I wanted just one table to contain all of the data associated with a user. Instead of ET_UserData and ET_Detailed user data I wanted just one table. But I decided to break this table up into the two tables for the following reason.
1.) This is a web application where each user logs into a web form. At a minimum, in order to use the website the session associated with each user needs the UserName, Password, First and last name.
This is the data in the first table.
If they choose to do more specialized functions on this website, then they will need all of the information (Attributes) that are located in the second table. In general 40% of the time all users will need information located in the second table.
My reasoning for breaking the table into two seperate tables is that I wanted to minimize the amount of data involved in a result set, created from the sql query. The math tells me that 60% of the time most of the data in the result set will not be used.
2.) If I create one class to represent all of the data/attributes in both tables, then my reasoning is that their will be alot of overhead in the single class because 60% of the time, a majority of the attributes are not needed and used.
I would deeply appreciate your help with this. You seem to have great insight and advice. Please help me as I increase the duke dollars Sir.

Need help in Architecture Design

Hi All,
Currently we are facing an issue in design of SAP Landscape which has CRM, EP, BW. We need to generate and display reports on B2B screen by accessing BW. Can some one help me out in providing some docs or links that give an insight in desinging the landscape with various approaches.
All Helpful answers will be rewarded.
Regards,
Udaya

Hi Udaya,
See if any of the following links prove to be of any help:
EP 6.0 integration with BW, R/3, and ORACLE
<a href="/people/kamaljeet.kharbanda/blog/2005/09/14/sap-netweavercomplete-information-integration-platform:///people/kamaljeet.kharbanda/blog/2005/09/14/sap-netweavercomplete-information-integration-platform
Bye
Ankur

Need Help With Spreadsheet Design

Hi,
I write about diabetes on various Internet Forums and am currently involved in testing various blood glucose meters to determine the accuracy of the different makes/models. I am trying to design a spreadsheet in Appleworks to help me evaluate the meters but have very little experience with spreadsheets so am finding it tough going.
In comparing the various blood glucose values delivered by the meters I am trying to come up with a way to automatically compare 2 readings and then display how much a particular reading is above or below another percentage wise. The difficulty is that a particular meter might sometimes display a value higher than another one time, and lower than another the next time so I'm not sure how to design the speadsheet to automatically calculate the percentages.
For instance in sample one Meter A reads 115mg/dl and Meter B reads 87 mg/dl so by dividing the 115 into 87 I can determine that Meter A is reading 24% higher than Meter B. But then in sample two Meter A reads 89 mg/dl while Meter B reads 121 mg/dl so in this case Meter B is reading 26% higher than Meter A.
Is there a way to structure the spreadsheet so that it can compare the two readings and then based upon which one is higher divide the result into the lower one can come up with a percentage?
Thanks!
Winston

Hi Winston,
Leaving aside any discussion of the actual test design, here's a rundown of how to make the spreadsheet do (most of) what you want it to do.
What I want the spreadsheet to do is to accept the data from meter 1 and meter 2 in side by side columns of cells. I next want the spreadsheet to compare the 2 bG values obtained from the same blood sample with these meters to one another and then divide the smaller value by the larger value to determine the amount in percent that one meter is higher or lower than the other.
This division (r/R) compares the smaller value (r) to the larger (R) and reports the result as a fraction.
eg. 75/100 = 0.75 The smaller reading is 75% of the larger reading, or the smaller reading is 25% lower than the higher reading.
But that does not mean the higher reading is 25% higher than the lower. That percentage is given by comparing the larger reading to the smaller (R/r). For the same pair of readings:
100/75 = 1.33.. The larger reading is 33% higher than the smaller.
As the percentages will be listed in columns labeled "Meter x higher", the R/r division is the appropriate one.
This is comparison is complicated by the fact that meter 1 will sometimes return the higher of the two readings, and at other times meter 2 will be higher. Thus it's not a simple matter of asking the spreadsheet to divide the result of meter 1 by the result of meter 2 each and every time or vice versa.
Next on the agenda I want the spreadsheet to put the result obtained by the above calculation in one or the other of two additional columns of cells. In other words the spreadsheet will compare the value of meter 1 to meter 2, divide the smaller value by the larger value to determine percentage, and finally place the result obtained in one of two additional columns of cells. One of these additional columns of cells would be labeled Meter 1 Higher and the other would be labeled Meter 2 higher.
All of the formulas given previously will make a comparison.
Niel's and Barry's report the percentage by which the higher reading is higher than the lower.
Brie's and Terry's report the percentage by which the lower reading is lower than the higher.
All put the results into the same cell (column) without regard to which reading is highest. (Barry's set includes labels to identify the higher meter.)
Here's mine again, with revisions to place the results into separate columns:
Labels in Row 2: C2: Meter A, D2: Meter B, E2: A Higher, F2: B Higher
Tests results in Row 3, Meter A in C3, Meter B in D3
Comparison results in E3 and F3
E3: =IF(C3<D3,"",C3/D3-1) Set the Number Format of this cell to percent.
F3: =IF(D3<C3,"",D3/C3-1) "
Note: the IF() statement suppresses the result in the column reporting "is higher" results for the meter with the ;ower reading. Written as above, the formulas will report in both columns where both meters show identical readings.
Note2: As written, the formulas will return a #DIV/0! error if no results have been entered on that line. The version below suppresses any results until readings have been entered in column D.
E3: =IF(D3,IF(C3<D3,"",C3/D3-1),"") Set the Number Format of this cell to percent.
F3: =IF(D3,IF(D3<C3,"",D3/C3-1),"") "
Roughly 1,000 tests will be performed over a several month timespan and all the meter readings referred to above will each be compared by the spreadsheet.
The default size of an AppleWorks spreadsheet is 40 columns by 500 rows. Go Format > Document... to increase the number of rows to 1050 to allow room for 'roughly 1000 tests.'
For 1000 tests, fill the formulas above down through rows 3..1002 (aasumed in examples below).
Next I want the spreadsheet to examine all the cells in which meter 1 returned the higher result and perform the following calculations:
lowest percentage over meter 2 obtained
highest percentage " "
The second is easy: =MAX(E3..E1002)
Place the formula where you want this result reported.
The first runs into a problem: empty cells, or those with non numeric data are evaluated numerically as "0" by the MIN() function. There is a workaround.
Use an empty column to the right of the active part of the spreadsheet. (I've arbitrarily chosen column M)
M3: =IF(E3>0,E3,1000)
Fill down M3..M1002
This copies all greater than zero values into column M, and inserts a value of 1000 wherever the value in column E is 0.
The minimum value in this column (which is also the non-zero minimum of column E) is given by:
=MIN(M3..M1002)
Place the formula where you want this result reported.
number of identical readings obtained
I'm assuming you mean 'identical differences' in terms of percent higher.
There are a couple of difficulties here:
1. AppleWorks does not include a MODE() function which would extract the number appearing with the greatest frequency.
2. What constitutes "identical" depends on the (mathematical) precision of the results. AppleWorks can display results to 11 significant places (eg. 12.345678901), and actually does the calculations to a few more places than that. Given that precision, many results that are not significantly different willl not be identified as "identical."
Probably doable, but more detail needed before jumping in.
average percentage " "
average deviation
Not sure what you're asking with these. Can you elaborate?
Regards
Barry

Might Be OT - Need Help With DW Design

I am in the midst of transferring Access reports to Oracle. A lot of these reports display percentage data. What is a best practice for storing percentage data in a data warehouse? Should I add on the percentage calculations at the fact table level? I am trying to make the data warehouse design as simple as possible for the report writers.

Hi Adrienne,
IMHO, warehouses should never store a percentage. They should store the components that make up that percentage. For example, the warehouse should not store "% of total sales" column, but should instead store sales $ amount and from there analytics can be performed to calculate a percentage. A data mart is more of a place where you would materialize calculations, like %, for easier reporting.
That being said, straight-up warehouse design questions are better suited over Warehouse Builder
Good luck and hope that helps!
-Joe
Edited by: Joe Bertram on Dec 17, 2009 1:06 PM
Edited by: Joe Bertram on Dec 17, 2009 1:06 PM

Need help with scenario design

I need to design a scenario,
Data is coming from two tables in mainframe.....that data i need to combine and process it and insert to ECC.
How to design?.
What will be the steps using BPM?.
Can u please give me broad view on designing this scenario.

Thanks Prabhu..for the input.
Thanks Bhavesh. You got the point...that is what i am going to do.
I have a select with join....then i update the records selected from database.
But now, i want to resign the scenario..
What i want to do is...write a sync send. Then use the join sql to get data, send to BPM.
Then inside BPM, use select with for update only and update sql.
For getting records on fly and send to BPM, how can i do?. Can u please elaborate this?.
What all i need to do to run the join sql against table and get data to BPM?.
(Advanced mode in JDBC Adapter setting to serializable queries is not working). So i need to do this step to overcome.

Need help in web design

We need simple database design for our website
www.koolbuck.com. In addition, we might need dynamic webpages using
dreamweaver. Currently we host at godaddy.com with SQL or mysql.
This is the primary requirement:
1. customers can sign up, log in, view and request to change
their info. There are about 20 data fields.
2. Admin page can view/change/delete/sort customer accounts.
We can manually edit customer's request changing their account
info. I don't know if we need this since we might be able to access
database on godaddy.com
3. If possible, know which banner, date and time they click
on the banner.
If interested, please contact me at [email protected]
Vinny

Hi Chinna,
> i want to use HTTP to soap Scenario.Please let me know the necessary steps in the scenario.
Split this into 2 scenarios
1. HTTP to SOAP (Request) treated as Asynchronous.
2. SOAP to HTTP (Responce) treated as Asynchronous.
For HTTP to SOAP synchronous scenario
Here the receiver side request and responce structures no need to create, the receiver client will provide you the XSD file, on that XSD file having the request and responce message structures, so you have to import that to XI server as External definition.
For sender HTTP you have to create 2 data types, 2 message types as well as 2 message interfaces, 2 message mappings for request and responce messages and 2 service/Message interfaces (HTTP is outbound and SOAP is inbound).
Configuration objects are same.
Regards
Ramesh

Need help in UI design in ADF Mobile

Hi
I have a requirement to create the interaction as shown in the image at https://picasaweb.google.com/113470899999229420779/February32013?authuser=0&feat=directlink. I am not sure which component is it?
Please advise how to create this type of button in the header.

Hi there...
You should see a popup component in the layout section.
Also there is a new list view component, which can be set to static fixed data or databound. In ADF mobile, you have to get a little more creative with the use of components and styling. I also see that the display is an application menu.
ADF Mobile delivers a standard design pattern to achieve this through the springboard... however if you want that particular pattern, a styled popup is definitely the way you go.
Please check 'helpful' or 'correct' ;-)
S

Hi I need help regarding web design

Hi all I am currently studying A Level ICT and for our coursework we have to produce a website using Adobe GoLive. I have encountered a problem as I am manufacturing an online sports shop and instead of having portal pages I was considering have a dropdown tab (not sure what they are called) appear once you hover over a button. Below are some examples of this
http://www.kitbag.com/stores/kitbag/football.aspx
http://www.jjbsports.com/
I have asked my teacher for help but she won't help me because to be honest I dont think she knows herself. I would greatly appreciate it if someone could help me because I am new to the software and am clueless. If you can help please comment here or send me an email to [email protected]
Thanks Matthew

It may interest you to know that Adobe stopped product development and support for GoLive back on April 28, 2008. I'm flummoxed as to why you are being taught to use obsolete software. You should be working with modern web developer's tools, not an outdated product that will never again see the day of light.
Dreamweaver CS5 generates web standards code for 2011. GoLive does not. If interested, Dreamweaver has an Academic Rate for students and teachers. Please pass along this info to your teacher.
http://tryit.adobe.com/us/cs5/studentteachereditions/?sdid=FXOPM&
All that said, the menus in your examples are called Mega Drop-Menus and they are based on an open source JavaScript library called jQuery. If you can work with HTML and CSS source code, you can implement Mega Menus into your pages fairly easily. See link below for Demo and Code Tutorial:
http://www.sohtanaka.com/web-design/mega-drop-downs-w-css-jquery/
Best of luck,
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
http://alt-web.com/
http://twitter.com/altweb
Message was edited by: Nancy O.
"see the day of light." Should have said, "see the light of day."

Need help with a design

Hi All,
I have a peculiar requirement and would appreciate your suggestions/inputs in designing this.
The client needs a custom UI from where they can select the different letters/documents they want to generate. But they want to preview the document and make any changes to it before they print it.
For example, the user select letter1, letter2 and letter4 to be generated. He clicks on the 'preview' button and the 3 documents (MS Word) are created. But he wants to change some data in one of the letters (for example 'Need by Date') and then when he is satisfied, he clicks on the 'Generate' button. The generate button should merge all the 3 documents (with the changes made by user) as 1 pdf and email it to a particular email account.
I can handle the dynamic template and merge/delivery part, but how can I take care of the case where a user makes changes to the generated report? We are on EBS R12.0.6
Any suggestions?
Thanks,
Ashish

you need some kind of reverse engineering, client change generated report and the change should reflect to template
use xsl templateEdited by: arjamit on Nov 4, 2009 1:47 AM

Need Help In BGP Design-Multihomed

Similar Messages

Maybe you are looking for