Need to send 32 packet within 15ms through UDP

Hi all,
I need to send 32 packet within 15ms through UDP in labview 2012. Each packet carries 2560 bytes. If it can able to send all packet within 7 or 8 ms, then it should wait upto 15ms and again it should repeat the same.
Please, anyone help me.
My code is as below.
Thanks,
Attachments:
DAC_labview.zip ‏49 KB

I wouldn't go that far, Shane.
I think that there is some confusion/misunderstand around this topic.
YES, you can use LV to send data using UDP and TCP to other systems.
NO, UDP by itself does not ensure lossless data transfer. So UDP can lose packets. That is something which LV cannot influence by any means. TCP is a lossless protocol which should be used if you require the security.
NO, neither TCP nor UDP are deterministic. So even if the packages you are sending are sent within a time x ms, there is no one garantee of any means that this happens EVERY time. Sometime packages might take a multiple of this time.
NO, transfer times are not influenced by the sending PC at a primary level. It all depends on your network; if the network sucks, using UDP packages are lost. If using TCP, packages are resent, so it also depends on sender and receiver alike.
Norbert
CEO: What exactly is stopping us from doing this?
Expert: Geometry
Marketing Manager: Just ignore it.

Similar Messages

Need to send Smart form via email through Driver program

Hi All,
We need to send smart form via email through a new driver program (z program). Can you please guide me on this.
I have used the following code to achieve this. We are getting message saying 'Mail request has created' when executed, but the mail is not sent.
lvs_comm_type = 'INT'.
lvs_comm_values-adsmtp-SMTP_ADDR = e_mail.
lvs_comm_values-adsmtp-R3_USER = 'X'.
lvs_comm_values-adsmtp-ENCODE = '0'.
call function 'CONVERT_COMM_TYPE_DATA'
exporting
pi_comm_type = lvs_comm_type
pi_comm_values = lvs_comm_values
pi_screen = ' '
pi_newid = 'X'
importing
pe_itcpo = lvs_itcpo
pe_device = lvf_device
pe_mail_recipient = p_mail_recipient
pe_mail_sender = p_mail_sender
exceptions
comm_type_not_supported = 1
recipient_creation_failed = 2
sender_creation_failed = 3
others = 4.
if sy-subrc ne 0.
raise COMMUNICATION_ERROR.
endif.
control_parameters-device = 'MAIL'.
output_options-TDIMMED = 'X'.
output_options-TDDELETE = 'X'.
CALL FUNCTION fm_name
exporting
CONTROL_PARAMETERS = control_parameters
MAIL_RECIPIENT = mail_recipient
MAIL_SENDER = mail_sender
OUTPUT_OPTIONS = output_options
USER_SETTINGS = space
EXCEPTIONS
FORMATTING_ERROR = 1
INTERNAL_ERROR = 2
SEND_ERROR = 3
USER_CANCELED = 4
OTHERS = 5.
Thank you

Hi,
For sending smartform output into mail you first have to generate spool request and convert it into PDF and then
only it can be sended into mail, please find the sample code in the mail below:
http://wiki.sdn.sap.com/wiki/display/sandbox/ConversionofSpoolRequestDataintoPDFandExcelFormatandSenditintoMail
Mansi
Edited by: Matt on Jan 29, 2010 8:25 AM - removed code, instead point to wiki that Mansi authored.

Need to send sms to the customer through Oracle Apps Custom form

Hi All,
This is sandeep, i have design a Oracle Apps Custom form, i am entering the Customer related date like customer name, number, customer Amount, cheque number, customer phone number, user want, when the user will save that form, so that above information should be send to the particular customer automatically, user entering the only one customer at a time. again user will open the new form and enter the new customer related data for that i have URL provided by the third party.
Please help me how can i achieve it, and what code i have to write and where.
it's urgent. kindly reply me as soon as possible
Thank you in advance
Regards
Sandeep
Edited by: user13014881 on Feb 14, 2012 10:25 PM

I have resolved that issue my self. now i am able to send transitional messages to the customers.
Thanks
Sandeep

Need to Understand the Packet Flow

Dear Friend,
I need to understand the packet flow of the below diagram.
I have configured MPLS on R2,R3 and R4. And IBGP is configured on R2 and R4. Now I am able to reach from R1 to R5's Loopback address. I need to understand the packect flow from R1 to R5 like If I ping from R1's Loopback to R5's Loopback address then Source IP is 1.1.1.1 and destination IP is 5.5.5.5. What will be the packet structure at R2, R3,R4...??????????
Please explain in details......Me really confused as R4 has not route about 5.5.5.5 also 1.1.1.1...How it forwards the packets??????

Sanjib
So R2 and R4 are PE devices and R3 is a P device ? And you are not doing MPLS VPNs, just normal MPLS ?
If so R4 must have a route to 5.5.5.5. Did you mean R3 does not have a route ?
With MPLS any P device only knows how to get to other P devices and PE devices. It does not know about any networks outside the MPLS network. The PE devices have routes to any external networks connected to them and know how to get to P and other PE devices.
Note that in terms of PE/P reachability the routing/LDP information has already been exchanged and an MPLS forwarding table built. So for reachability between PE/P routers (ie. not outside the MPLS network) route lookup do not need to be performed, it is simply a matter of removing and adding labels.
So assuming you are not using MPLS VPNs and that MPLS labels have been exchanged between all P and PE routers -
R1 pings 5.5.5.5
1) R1 does a route lookup for 5.5.5.5 and sends it to R2.
2) R2 is a PE device. It does a route lookup for 5.5.5.5 and sees R4 as the next hop (this route has been exchanged via MP-BGP).
3) R2 then need to send the packet to R4. To do this it looks in it's MPLS forwarding table to see how to get to R4. The MPLS forwarding table tells it which label to attach to the packet. It adds this label and sends the packet out of it's interface to R3.
3) R3 is a P device. It does not need to do a route lookup for 5.5.5.5. It simply looks at the incoming MPLS label and consults it's MPLS forwarding table. It will have an entry in it's table saying that an incoming packet with an MPLS label of x should be sent out with an MPLS label of y. It changes the label and sends it out to R4.
4) R4 receives the packet, removes the label, does an IP lookup for 5.5.5.5 and sends it to R5.
Note that actually R3 might not add a label as there is something called Penultimate Hop Popping where if the net hop from the P router is a PE router it sends the packet without a label to save extra processing on the PE router. If you had multiple P routers only the last P router before the PE router would do PHP.
The key thing to understand is that the P devices don't do route lookups when forwarding data. They simply switch labels. Whereas the PE devices do need to do route lookups for destinations outside the MPLS network.
Jon

Make a Cisco SPA 303 ring by sending a packet through your network?

Hey Guys,
I was wondering, and I need to know for my business, is there any way at all for me to make my Cisco SPA 303 VOIP Phone to ring by sending a packet through my local network?
I would like to just be able to click a button or send a command throught the command prompt and make it ring, but I don't know if there is any way for this to happen.
Thank!

Do you know perl?
I had same issue and I wrote a simple perl script that works as wake up service.
PERL is an interpreted language and so can be executed on Linux and Windows operating systems. Linux can interpret perl natively while for Windows you can download many free interpreters like Activeperl or Strawberry perl. To run the script you must use a third party server.
In my configuration the script runs on a linux server in background as a service and checks every minute the directory called "alarm", reads files and uses the file name as called number and checks the content to verify if is the time to call. At the moment the script uses SIP and handles 4 call responses: 404 user not found, 486 busy, 487 not answer and 200 answer ok. In every cases sends an email and deletes files. Only for the answer case plays a nice music.
Files have this particular format: file name is equal to calling party number and file content is the alarm time in 24 hours format with : as separator between hours and minutes.
e.g.
ext. 101 must be called at 8 am ---> write the file 101.txt with the content 08:00
ext. 101 must be called at 8:30 am ---> write the file 101.txt with the content 08:30
There is a limitation: if you activate the Authentication for SIP messages and there are more then two simultaneous calls, the script sends some INVITEs without authentication or with wrong checksum and so not all phones ring. This problem is under investigation.
Are you intresting?
Regards.

HR: Need to Send the Paysilp as a PDF file through Mail to Employees

Dear All ,
       Need to Send the Paysilp as a PDF file through Mail to Employees.
       can anyone please suggest any Standard Function Modules which takes the Payslip Form as input and convert it into PDF and can send it through mail to the concern employees.
      Can anyone please explain the procedure in detail.
Thanks in Advance,
Regards.

venu,
below is code which helps to generate pdf ,,,,hope u know how to use the mail sending function
data:
fm_name TYPE RS38L_FNAM, "Smart Forms: FM Name
sf_name TYPE TDSFNAME
value 'YOUR_FORM_NAME', "Smart Forms: Form Name
P_OUTPUT_OPTIONS TYPE SSFCOMPOP,
P_JOB_OUTPUT_INFO TYPE SSFCRESCL,
P_CONTROL_PARAMETERS TYPE SSFCTRLOP,
P_LANGUAGE TYPE SFLANGU value 'E',
P_E_DEVTYPE TYPE RSPOPTYPE.
data:
P_BIN_FILESIZE TYPE I,
P_BIN_FILE TYPE XSTRING,
P_OTF type table of ITCOO,
P_DOCS type table of DOCS,
P_LINES type table of TLINE,
name type string,
path type string,
fullpath type string,
filter type string,
guiobj type ref to cl_gui_frontend_services,
uact type i,
filename(128).
GET SMARTFORM FUNCTION MODULE NAME ---
CALL FUNCTION 'SSF_FUNCTION_MODULE_NAME'
EXPORTING
FORMNAME = sf_name
IMPORTING
FM_NAME = fm_name
EXCEPTIONS
NO_FORM = 1
NO_FUNCTION_MODULE = 2
OTHERS = 3
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
CALL FUNCTION 'SSF_GET_DEVICE_TYPE'
EXPORTING
I_LANGUAGE = P_LANGUAGE
I_APPLICATION = 'SAPDEFAULT'
IMPORTING
E_DEVTYPE = P_E_DEVTYPE.
P_OUTPUT_OPTIONS-XSFCMODE = 'X'.
P_OUTPUT_OPTIONS-XSF = SPACE.
P_OUTPUT_OPTIONS-XDFCMODE = 'X'.
P_OUTPUT_OPTIONS-XDF = SPACE.
P_OUTPUT_OPTIONS-TDPRINTER = P_E_DEVTYPE.
P_CONTROL_PARAMETERS-NO_DIALOG = 'X'.
P_CONTROL_PARAMETERS-GETOTF = 'X'.
****...................................PRINTING.........................
CALL FUNCTION fm_name
EXPORTING
CONTROL_PARAMETERS = P_CONTROL_PARAMETERS
OUTPUT_OPTIONS = P_OUTPUT_OPTIONS
(....) <--- your form import parameters
IMPORTING
JOB_OUTPUT_INFO = P_JOB_OUTPUT_INFO.
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
P_OTF[] = P_JOB_OUTPUT_INFO-OTFDATA.
****...................................CONVERT TO PDF...............
CALL FUNCTION 'CONVERT_OTF_2_PDF'
IMPORTING
BIN_FILESIZE = P_BIN_FILESIZE
TABLES
OTF = P_OTF
DOCTAB_ARCHIVE = P_DOCS
LINES = P_LINES
EXCEPTIONS
ERR_CONV_NOT_POSSIBLE = 1
ERR_OTF_MC_NOENDMARKER = 2
OTHERS = 3.
IF SY-SUBRC <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
now you can mail the pdf.
Reward points if helpful
Regards,
jinesh

How to send a packet through a specific Inferface ?

Hello!
I have 3 interfaces in my pc : LAN / WLAN / 3G
On LAN I have a global IP.
On WLAN and 3G I'm behind NAT.
I'm coding a program (client+srv) >
I watch a video streaming on LAN then I switch to WLAN or 3G and I want it to happen seamless. So basecly seamless vertical handover is my goal.
Because I'm behind a NAT (3G,WLAN) First I have to send a packet to the server (connection initialization). When the server sends the stream to me it actually sends it to the NAT and the NAT will fwd it to me.
The NAT send the packets back to me only if>
1. the server sends from the same port which it received the request form the NAT
2. It have to send to the same NAT (ip+port) address where the request came from
3. NAT will send then the packet back to my PC to the same port where I sent my request from.
Here comes my big problem!
I have a socket bound to a IP1 and port (e.g. WLAN) if I want to send a packet to an destination IPx for which the route table has the LAN interface as default gateway (IP2), then it will send my packet trough the LAN (IP2) but the source IP will be IP1 in the packet.
Basecly I have a WLAN package on my LAN.
This is bad for me in 2 ways.
1. there won't be a NAT binding for my WLAN
2. the packet won't even make it to the server because the very first router will throw it away since it's source IP is not a LAN IP
SO,
is there a way in Java, to send a packet thorugh a specific interface???
Thx for the kind help!
r0hamkuka

I used NetworkInterface.getNetworkInterfaces() to get all avaliable interfaces. After that I used this: interfaceSocket = new DatagramSocket(6000, interfaceIp); for all my interfaces with different interfaceIp of course
The I tried to send a packet to 153.66.200.155 for example (LAN address) through my WLAN interface (ip for example: 192.168.1.101) using WLAN's interfaceSocket.send()
But the packet goes out on my LAN interface (ip 153.66.200.166) while the src ip is still 192.168.1.101 in the packet. That is why I sad WLAN packet on LAN interface.
I guess the reason is still the routing table. Because routing table tells which IF to use for a destination IP. Of course for dest 153.66.x.x routing table contains 153.66.200.166 as the gateway and not 192.168.1.101. So Win uses this the LAN IF to send the packet.

How to send RTP packet through SIP Dialog

Hello there !
I work on a Java softphone which use JMF and Jain-SIP. I know JMF is "old" but I think it would be simple to capture and transmit RTP audio. So, my SIP dialog is working, I can send text messages but now, I would like to send RTP with this SIP session. I know I have to send SDP messages for codec convenience but then, what is the MediaLocator for RTP packet ? Only SIP User Agent IP or something else ?
I also accept all ressources that can help me achieve my work :)

I have no idea how SIP works, but, RTP packets go to an IP:PORT... theoretically, in the SIP phonecall setup, I'd imagine you'd have to be given the address to send RTP packets to the remote phone. Or perhaps the port is already well-defined by the SIP standard.
Either way, you should have a way of knowing / finding out which PORT to send to for your SIP call, either from the call setup or the SIP standard itself.

I need help I can't send pictures to my wife through iMessage

Hope someone can help me well about a week ago I could not send pics to my wife's iPhone she has an iPhone 4s and I have the iPhone 4 one day last week I tired to send some pics to her through the iMessage and it would not deliver them but we have been sending pics to each before and now she can send me pics but I can't send them to her but I can send pics to my daughters iPod I have done things that I have read to try to fix the problem but nothing has worked help me płease

Yes I can send texts but no pics she can send me pics I get them just can't send them I have turned off my messages did a he'd reboot turned messages back on so I just about tried everything that I have read on here

Cannot send email from within iPhoto

Using OX X 10.7.5 cannot send email from within iPhoto. I get this error message: "Your email did not go through because the server did not reply."
If I change the preference to use email, everything goes fine but I lose the formatting feature.

iPhoto Menu ->
Preferences ->
Accounts ->
Delete and recreate your email settings.
Alternatively, use Apple's Mail for the job. It has Templates too - and more of them. Check out the Stationery...

If you need to send more than one document via email to a recipient with a PC, how do you convert them to a Word or PDF before sending them in one email?

When trying to send an email to a PC user and need to send multiple documents, in the old version of iPages, you could save the document as a Word or PDF file then attach them to the email. I don't see how to do this with the new version. Therefore, the only way I can see to accomplish this task is to go to each document and send them individually in another version. Otherwise, the PC user will not be able to view the documents - correct. There must be a way to convert and save the documents like before so numerous documents can be sent at once. Please help!
Melody

What fruhulda said. In addition, in the Mail composition window, I recommend that you select the paperclip icon from the Toolbar, and enable Send Windows-Friendly Attachments.
You can also select multiple files in the Finder and drag them onto the composition window. In my experience, the documents resist an iconic state, so right-click on just one, and choose View as Icon from the contextual menu. This will transform all attached documents into icons.
If you want to send just one document from within Pages v5, use the Share icon in the Toolbar and select Send a Copy > Email. You can then choose PDF (and its image quality), or Word (.docx default, or .doc) document formats that will be attached as an icon in a new pop-up Email composition window.

PMW (Payment Medium Workbench) and needs to send Payment Advises to Vendor

Hi SAP Gurus,
We are using PMW (Payment Medium Workbench) and our client needs to send Payment Advises through mail. After running F110 system should trigger mail to vendor for payment advise.
We have created one DME format and it's working fine. DME file is getting generated when we assign DME format to our payment method.
we have also made the change for payment advice sending through email. Copy FM SAMPLE_PROCESS_00002040 to ZSAMPLE_PROCESS_00002040
Go to transaction FIBF
Settingsprocess modules of an SAP application
Add a new entry for 00002040 FI-FI ZSAMPLE_PROCESS_00002040
Make use of FM ZSAMPLE_PROCESS_00002040 for adding vendor email address and make the payment medium.
Now the problem is, we can not do this in one go, if we need to create DME file than we have to assign DME format to our payment method and if we have to send payment advice to our vendor than we need to use Payment Medium Program RFFOGB_T (standard program). It's radio button and we can not choose both the program and Payment Medium Workbench.
I need your valuable advice what need to be done in order to get DME file and payment advice send to vendor in one go.
many thanks for your reply.
regards,
SATVIR SINGH

Hi Stavir,
Do you recall how were you able to resolve this issue?
Thanks
M

Need to send the zip file to mail as an attachment

i want to pick the zip file which consists some 2,3 files inside it. and send as it is to mail as an attachment.what i did is
i have taken one zip file,,, "testing.zip" inside it i have "test1.txt" & "test2.csv"
i created sender CC ,,in that i used module payloadzipbean and unzipped and called the file adapter.. created reciever CC as mail ..used same payload module now here i zipped all the payloads.
Result..i see the attachment coming as "test1.txt.zip" ..here i can see inside this zipfile my original file names as "test1.txt"&"test2.csv" as i enabled ASMA in both CC.
issues:i am unable to get the original file name like "testing.zip" ,,
can anyone help me in this.
Regards,
Loordh

Hi all,
as i posted last time my requirement ,i am going with java mapping for my scenario. i am using this code .
http://wiki.sdn.sap.com/wiki/display/XI/Dynamicfilenameforpass-through+scenario
this is working perfect for zip file (file to file) scenario. but my scenario is file to mail ..as i need to send this to mail package there it is throwing error.i am getting "zip file name as attachment properly but when i try to open it is giving error in zip file." this is what i modied code ..i am able to see my messge in sender CC and reciever CC..any java experts please help on this.
try {
// create XML structure of mail package
String output = "<?xml version=\"1.0\" encoding=\"UTF-8\"?>"
+ "<ns:Mail xmlns:ns=\"http://sap.com/xi/XI/Mail/30\">"
+ "<Subject>" + mailSubject + "</Subject>"
+ "<From>" + mailSender + "</From>"
+ "<To>" + mailReceiver + "</To>"
+ "<Content_Type>multipart/mixed; boundary=\"" + boundary + "\"</Content_Type>"
+ "<Content>";
out.write(output.getBytes());
// create the declaration of the MIME parts
//First part
output = "--" + boundary + CRLF
+ "Content-Type: text/plain; charset=UTF-8" + CRLF
//+ "Content-Transfer-Encoding: 8bit" + CRLF
+ "Content-Disposition: inline" + CRLF + CRLF
+ mailContent + CRLF
//Second part
+ "--" + boundary + CRLF
+ "Content-Type: Application/zip; name=" + attachmentName + CRLF
//+ "Content-Transfer-Encoding: base64" + CRLF
+ "Content-Disposition: attachment; filename=" + attachmentName + CRLF + CRLF;
out.write(output.getBytes());
//Source is taken as attachment
copySource(in, out);
out.write("</Content></ns:Mail>".getBytes());
} catch (IOException e) {
throw new StreamTransformationException(e.getMessage());
protected static void copySource(InputStream in, OutputStream out)
throws IOException {
byte[] bbuf = new bytehttp://in.available();
int bblen = in.read(bbuf);
if (!(bblen < 0)) {
//String sbuf = new String(bbuf);
//String encoded = Base64.encode(sbuf);
// replace all control characters with escape sequences
//sbuf = sbuf.replaceAll("&", "&");
//sbuf = sbuf.replaceAll("\"", """);
//sbuf = sbuf.replaceAll("'", "'");
//sbuf = sbuf.replaceAll("<"<");
//sbuf = sbuf.replaceAll(">", ">");
out.write(bbuf);}}

In APP i need to send a check thourgh business area

Dear Gurus,
please tel me In APP F110 i need to send a check thourh business area
please help me
Regards,
Shekar.

Hi Anil,
while running APP F110 in the Free Selection Screen Select Business Area
through that Business Area you can pay checks

Need to send form item inline of an email

Hi,
I need to send an email with a form item that would send REQUEST and submit a note to a database table text column.
an email with an HTML form w/ submit button..
Is there a link to a HOW TO ?
Thank you, Bill

Hi, Thank you for the link but I already send email in my app....
I guess the real question is:
when sending an email from with in the app, how do you build the syntax to have a button with in the email to take the receiver of the email into the app...
or in the email have a comment textarea and a button
When the email user clicks the button it sends the textarea to the app and updates it.
how do you make it so if the request comes from the email you don't need to logon?
As I typed this I kinda am getting ideas... just to build a form within the email but it is the ? form action line I need to know how HTML_DB needs the syntax to be...
Clear as mud?
Thanks Bill

Need to send 32 packet within 15ms through UDP

Similar Messages

Maybe you are looking for