Neo2- Posting problem and HDD detection

My system is:
K8T Neo2 FIR
Athlon 64 3400+
Chaintech Geforce 5500 256mb
Samsung 120gb SATA
52x cdrom
I initially had a problem where it would not post at all. So after playing around I finally got it to POST by messing with the JBAT1 jumper position. Can someone by the way please tell me the correct position for this jumper? There are 5 pins there and in the book and everywhere else I look it shows there should be 3.
Anyway after I get it to post it says bios not installed etc, so i load setup with defaults and continue. Now I get to installing windows and it gets to the point of detecting my HD and says it could not find any. My SATA harddrive was detected by the BIOS, why not XP? So I have to reboot, but no POST! So I take the jumper off and put it right back on. That is the only way I can get it to post. Anybody know whats going on before I send all this stuff back?

Ok, amidst the BIOS craziness I was able to get WinXP installed and all the necessary drivers. I still am having a problem rebooting. Before I turn it on I must remove the JBAT1 jumper and replace it. Then it turns on when I press power. The same thing happens when I reboot, it doesn't completely shutdown so I have to shut it down manually, and again to turn it back on I have to pull up the JBAT1 jumper and put it back. Then it turns on. This is a stupid problem to have. When I boot it says No bios installed. And every bootup it gives me the menu Press F1 for setup or F2 to Load defaults and continue. Anyone know whats going on ?

Similar Messages

Lenovo P780 Kitkat 4.4.2 upgrade: Post problems and changes

1. New security system ( neither can be uninstalled nor disabled) actually speaking it is annoying to me. Now a days it is asking for Money Rs.53 for 30 days.
2. Very bad UI ( had to install NOVA Launcher to change it )
Does anyone know how to uninstall Lenovo Security. Please help me i dont want it anymore.

SecureIT is a completely free app.
The problem you are describing(virus database upgrade fee) is usually related with improper SU binary installation (rooted device loosing root access>CWM/TWRP re-rooting).That's why I asked about root access.In that case the solution was to uninstall and reinstall the app (ROOT needed).
The funny thing is that if you want to remove it you have to root the phone.
Rooting instructions HERE.
Important:If you remove SecureIT you won't be able to install future OTA updates.Suggest ''freezing'' it (ROOT needed).
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as ''ACCEPT AS SOLUTION"!
Unsolicited PM's will not be answered! ....Please post your question/s in the appropriate forum board.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество

MSI 6330 turbo2 and hdd detection

Hi, i have MSI 6330 turbo2 motherboard with Award bios 6.00PG on an old machine. I tried to put a 40 gb hdd (seagate st340014a) on it but it only reports that the hdd has 32gb of storage... I know that some of the award bios's have the 32G limit problem and i have read that by updating the bios it is possible to overcome that limitation. I have downloaded the latest bios and flashed the board but it still has that limitation. Have i done something wrong, is there another newer bios upgrade for this MB?

I have the latest bios available, that is v3.6 and it still doesn't work. I have checked the jumper settings and it was set to master, just in case I removed the jumper (slave according to the manual) just to make sure that I didn't mix the capacity limitation jumper and the master jumper but it still reports that the drive has 33821mb and not full 37gb... not sure what to do
Can i downgrade the bios to an earlier version (3.5)?
Also it has come to my mind that i could manually set the size of the drive in bios, can anybody please tell me the exact CHS config for this drive?
Thanks

K8n neo2 POST problem during cold startup

Hello everybody,
Sorry for posting this again but i just don't understand it.
The facts:
Every once in a while - sometimes daily and sometimes every 2nd or 3rd day - when I power on my computer the bios hangs at its very first stage with all d-leds red.
This is according to the d-bracket : 'system power on, bios will hang here if processor is damaged on not installed properly'.
But after ~ 30 seconds the boot process continues (it apparently doesn't start again but continues) displaying the following error message after IDE detection: 'warning. system now in safe mode. please reset all overclocking features.'
After that everything is FINE, the bios settings are as always (failsafe with sata enabled) and the computer has no other problems. It runs all applications without trouble, memtest86 and prime95 don't give me errors and I won't get bsod's.
This entire issue happens only when the computer was turned off for a prolonged period, i.e. it has to be off for more than 6-8 hours.
I just don't understand it .
I see that here are a couple of guys with quite a huge knowlege of this machines and so i hope that someone has a clue to what this issue can be caused by and perhaps how it could be solved ?
Thanx,
vanish
(Forgive me my misspellings, i'm not a native so)

This is the email I sent to MSI UK:
Hi
I believe I have a faulty motherboard as the BIOS only posts after I switch the power on at least 3 - 6 times from a cold boot.
The error message I keep getting is 'warning system now in safe mode, please reset overclocking features in bios or press F1 to continue' although I have not altered any overclocking features or overclocked anything. One thing I have noticed is that the processor is running at 2210 Mhz (used MSI Core Centre) instead of 2200 MHz as standard even though it is displays 200 MHz in the BIOS, could this be possibly something to do with it?
Please could you suggest what process I need to do to RMA the board or how I could diagnose the problem.
I have tried 3 different types of RAM in various slots, 1 and 2 sticks, dual and single channel and the same thing keeps happening.
My PC Spec:
Athlon 64 3500 90nm
Thermalright XP-90 Heatsync with a Vantec Stealth 90mm fan.
MSI K8N Neo 2 Platinum
TRIED RAM: 2 x 512 MB. Infineon 3-3-3-8 Cas 2 PC3200
2 x 512 MB. Corsair LL-PRO PC3200 2-3-2-6 Cas 2 (currently using)
2 x 512 MB. Adata 3-3-3-8 Cas 2.5 PC3200
2x120 GB Maxtor Diamondmax 9 SATA hard disks (not in any RAID config)
Galaxy Geforce 6800 GT
Soundblaster Audigy 2
Tagan 480W PSU.

For people having POST problems (long IDE detection) on Cold Boot with K8N Neo 2

It's been 2 weeks that I'm looking for the root of this particular problem.
I've found today how to get rid of it. Try this if you haven't already :
In BIOS root screen, activate the hidden settings (Press SHIFT+F2 and ALT+F3 rapidly)
Then go to the Cell Menu and disable NV/ATI Speedup feature.
Save your settings, turn off your comp.
Restart and check with cold boots
Sweep

I have a worse variation of this problem (but also the startup IDE freezing that fixes with Alt-Ctl-Del), that I discovered while trying to boot from an ME CD or from a WinME Floppy boot disc when and only when I tell it to load support for CD-Rom going into DOS. It freezes when it gets just past detecting the IDE, requiring a cold boot reset.
If I boot off the WinME CD or a floppy boot disk, and don't choose CD-ROM support I can get to the A: drive with RAM C drive to be able to flash the BIOS (which I did up to 1.3, after which I reset the CMOS jumper). The problem persists with the new MOBO 1.3 BIOS.
I made sure the IDE-2 ribbon was connected properly, and even tried changing the jumper from master to cable select on the Plextor DVD burner....still locks up when I boot to DOS with CD Rom support enabled.
My next step was to disconnect the IDE cable from the Plextor so the drive was not the issue, and it still freezes if I choose CD Support from Boot disk.
I next removed the CMOS battery (which btw, will require you to call MS to reactivate XP), checked the voltage with a battery tester, replaced it, cleared CMOS jumper again, use mostly default BIOS settings except disabled SATA, and the same damn problem.
My friend, Triple6 in this same thread has the identical setup except different RAM, different nVidia 6800 Ultra Video card and he does not have the same bootup issue. We checked the same BIOS settings.
I'm beginning to wonder if I have a bad MOBO that won't allow me to boot off a floppy with CD-ROM enabled. Very Strange!

Alternative to posting problem reports via OSS?

Sometimes I find problems with SAP software, like the RFC library, that I'd like to be able to report, however I'm not always in a position to do so, as I may not be working at a client site at the time (and it would not be appropriate to log the problem under their installation).
What is needed, IMO, is a way to log these problems without the formality surrounding OSS and SAPnet. I imagine this would be important too for those coming into SAP for the first time from the Java side.
Perhaps the easiest way would be to mark a forum posting as a problem report, similar to the way it can be marked as a question. This would then allow for highlighting to forum members from SAP who could decide whether the problem warranted escalation.
Cheers,
Scott

Hi Scott,
i agree. There should be a possibility to create a linkage between OSS notes and SDN postings in some cases, because (besides or in addition what you've already said):
1. Problems which are reported to OSS might already have been resolved in SDN and vice versa. A common knowledge repository would be very helpful for both parties, i guess. In my opinion it's easier (and cheaper) to <b>verify</b> a possible solution published already in SDN than finding/creating a new one for OSS.
2. IMHO it's probable that a steadily increasing number of "productive versions users" of arbitrary SAP software components will start to post problems and possible bugs at the SDN forums in the near future. It's absolutely ok to redirect them to the OSS, since this is the official place to report and handle such issues.
But it should be possible for example to add a link referring the "SDN problem thread" to the customer message(s). The support team could then post the SAP notes number as a reply to the thread as soon as a solution is available. Otherwise, if people aren't gentle enough to return to the forums and publish the problem solution, it's not easy to find the official answer, since nobody knows how to search for the corresponding note to get reliable search results. If the problem description of the note doesn't repeat parts of the question text in SDN, you are lost.
3. Resulting from 2., more and more "information leaks" will arise in the SDN forums. But i dare to argue that people will return asking the same question(s) over and over again, if there's enough interest, until "somebody" is lucky enough to find the solution in the OSS and post the notes number. Why not "automate" this?
Just to clarify:
I do <b>not</b> want to have the OSS team bypassed, this is definitely wrong from my point of view.
Cheers,
Stefan

My Mac is doing strange things: delaying between users, mouse flickering and bouncing, gets stuck with rainbow wheel flickering. I ran the appel hardware test and it detected an error: 4MOT/4/40000003:HDD-1233 Does anybody know what that means? HELP!

My imac is doing strange things:
-delaying between users: when closing session it goes to blue, then takes a while to appear users signin box, and then wont recognize mouse command to enter until a couple of minutes later... then everything seems alright until....
-it gets stuck between things, the rainbow wheel appears and its just delays there forever....
-and every now and then the mouse starts flickering and bouncing wildly onscreen.
I ran the appel hardware test and it detected an error:
4MOT/4/40000003:HDD-1233
Does anybody know what that means? HELP!

WZZZ answered about where to get iStat. And do check the SMART status. If it is an overheating problem due to a fan or logic board problem, your hard drive is possibly cooking itself to death. If so it isn't a faulty hard drive even though the hard drive might fail. So assuming it's a temperature problem, even if you are able to repair things on the disk with software, that is working on symptoms, not causes. I could be wrong however.
RE: AppleCare: Your iMac came with one year of AppleCare (Apple's warranty program), but within the first year you can buy 2 more years. You have to extend by the one year anniversary of purchase of the computer. Your 10,1 is too old to still be in the first year, and since you asked what it was, I'm sure you don't have it. Bottom line meaning is that whatever this problem turns out to be, you'll have to pay for it. Unless there is something like this. It is for 2011 iMacs with certain Seagate drives. You can put in your serial number for fun, but it looks like yours is too old. Lastly, some people have had Apple help them anyway if it is just out of warranty, but many have not. Your machine is one of these. Type in 10,1 in the search box. Is there an Apple Store near you? Just b/c it's out of warranty doesn't mean you shouldn't have it looked at by Apple. But no one here can say at all what Apple will or will not do.
Hope you get it taken care of!

K9N2 Sli Plat - HDD detection problem

[Split off from https://forum-en.msi.com/index.php?topic=127332.0, please don't hijack other topics! - Stu]
You are not alone..... I'm having simular issues
I flashed my bios hoping to fix the HD detection for installing windows.
now I get nothing detected in the bios. as SATA drives. IDE channels detect.
Ihave flashed the bios both ways USB and CD bootable image.
I get a NVIDIA HDCP: ROM HOLE 2 PROTECTED!
During the flash. Is that supposed to happen? everything else looks good during the flash. However now I can't even get drivers to see the SATA drives. I've tried 2 different makers.
BIOS is set to IDE on the SATA.
Note Same MB as original thread starter. 8GB OCZ memory, hitachi 1TB HD, 160 GB Maxtor HD.

I split off your post from the other topic, as it was unrelated, and you should always start a new topic anyway, >>Please read and comply with the Forum Rules.<<
Now, please read the >>Posting Guide<< and give us a bit more detailed info on the hardware in your system, and the exact problem you are having, so we can begin to assist you!

Satellite A500-1C0 - Windows has detected a problem with HDD

Good day,
Notebook shows me that Windows has detected a problem with HDD. The notebook is slow and the chops. And when you turn it shows me Smart Failure predicted on hard disk 1. Toshiba MK 5055GSX - (S2). Can you help me? (Im CZ)
http://img684.imageshack.us/img684/8434/smartm.jpg

Hi Konyga,
If you already get a warning about internal HDD before Windows starts I would recommend exchanging it and backup all data as fast as possible.
Is your notebook still under warranty?
If yes you can get a new HDD from an authorized service provider. This would be for free because its covered by warranty. Everything what you have to do is contacting an ASP.
http://eu.computers.toshiba-europe.com > Support & Downloads > Find an ASP

P965 neo-f hdd detection problem

Hello, I'm facing a very strange problem. I'm using a p965 neo-f board, with a dual pentium 2.80GHz, a 250gb sata wd disk, 2x512mb corsair ram, ati radeon x1300, psu tagan 480w, ide dvdrw bios w7235ims v1.5. I build the system myself and installed windows xp x64 pro. Everything went ok and the system was stable. Some day there was a current breakdown and when i powered on the pc during the post it hanged at ide detecting disks. I've entered bios setup, save and exit rebooted and went back to windows. At the past 2 years i suffered a couple current breakdowns leading to the above problem that i'm solving it as i said before. I must say that the computer belongs to my sister and i'm her technician . During last week my sister decided to move the pc to another room. They connected the computer, powered it on and the same thing. During post it hangs on detecting disks. I took the computer at home changed the sata to the jmicron slot, and booted to windows. The problem is that the ethernet controller doesn't work. So i reinstalled all the mobo drivers, no luck. I did a bios update to version 1.90. The result was with sata connected to the jmicron, the ethernet controller is not working. I changed the sata to sata 6 and everything worked ok. Today I've opened the pc again to check it out and the same thing, post hangs at ide detection. I don't know what to do anymore. maybe the intel controller is messing up with the jmicron? or the bios is not suitable? should i downgrade to other bios versions? Any help will be appreciated. Thanks

Thanks for the reply, I thought about those things myself and I'll try them. Here is another weird one. Connecting the hard drive to sata2 slot everything worked well for a day.
Today I powered the pc in the morning and it recognized the disk. I Did some work and I checked the shutdown and the rebooting. Everything looked as It should be. So I went to the beach, and when I came back, I started the pc--->> the same thing happened!!!
Should I try another bios version? or It is just a waste of time?

HT4314 hello i have an ipod touch 4 5.1.1 and i can't post status updates or have a profil picture what is the problem and my sister has it and we have the same itunes account in game center

hello i have an ipod touch 4 5.1.1 and i can't post status updates or have a profil picture what is the problem and my sister has it and we have the same itunes account in game center

And the answer is:
williamfromlongueuil wrote:
we have the same itunes account in game center
You need to have your own account... DUH....

Goods Receipt and Goods Issue - Posting Date and Document Date Problem

Hi All,
I was using SDK to build own add on to insert Posting Date and Document Date under Inventory> Inventory Transactions> Goods Receipt and Inventory> Inventory Transactions> Goods Issue, but the UI Screen Posting Date and Document Date shown current date.
My SAP Business One version was 2007A SP00 PL42 and alreadly upgrade to SP05.
End up result still the same.
Is there someone can help me?
Thanks you.
Best Regards,
danny

Hi there,
I already solve it by myself.
Actually is i call the initialization twice:
Company.GetBusinessObject(SAPbobsCOM.BoObjectTypes.oInventoryGenEntry)
Thats what make this problem happened.
Sorry.
Best Regards,
danny

Can't load Netflix - Firefox says something about cookie problem and recommends try again button. ("The page isn't redirecting properly Firefox has detected tha

Can't load Netflix - Firefox says something about cookie problem and recommends try again button. ("The page isn't redirecting properly Firefox has detected that the server is redirecting the request for this address in a way that will never complete. This problem can sometimes be caused by disabling or refusing to accept cookies.)" Hit the try again button repeated ly - nothing???

I decided to give Netflix a call about this problem.
On a recording while waiting for a support rep, it said if you're having problems logging in to go to:
http://www.netflix.com/clearcookies
It works for me. Now I have to logon everytime I go to their site though versus it had kept me already logged in before this problem.
I will be using that link to get to their site until they get it fixed.

When I access the itunes store I get an error message saying that Itunes has detected a problem and has to be closed

When I access the itunes store I get an error message saying that Itunes has detected a problem and has to be closed. The rest of Itunes is working fine... Any help?

There could be any number of items causing this. First off is do you have an active internet connection? If so have you tried rebooting you computer?

Can I get help with podcasts? When I try to open the podcasts, itunes crashes, says "itunes has detected a problem and must close", or the spanish equivalent since my xp is in spanish. everything else works fine, it even downloads podcasts and syncs.

Can I get help with podcasts? When I try to open the podcasts tab, itunes crashes, says "itunes has detected a problem and must close", or the spanish equivalent since my xp is in spanish. everything else works fine, it even downloads podcasts and syncs.

The only other thing I can suggest is to use the Repair option for iTunes.
Download the iTunes programme (do not uninstall your current iTunes) and then "install" the new copy. At some stage you should see an option to "install" or "Repair". Take the Repair option.
Once you've done that, if you still have a problem, I don't know what else to suggest, except to search through the discussions to see if anyone else has had the problem and managed to fix it.

Neo2- Posting problem and HDD detection

Similar Messages

Maybe you are looking for