Netctl problem - No connection on interface 'enp1s0'

I'm trying to switch from netcfg to netctl.  Since the network won't come up, it would be difficult to post actual logs so I'm typing all this in.
/etc/netctl/mynet looks like:
Description='My net'
Interface=enp1s0
Connection=ethernet
IP=static
Address=('192.168.1.102/24')
When I try to start it, I get from systemctl status [email protected]:
... network[1877]: Starting network profile 'mynet' ...
... network[1877]: No connection on interface 'enp1s0'
and then some failed/exited messages.
Sorry that's not much to go on, but perhaps someone can point me in the right direction.

Heh, it just dawned on me that I could use the modem even if the network is down.  Just in case someone can see a typo I'm missing, here's the actual config without the commented lines:
Description='My net'
Interface=enp1s0
Connection=ethernet
IP=static
Address=('192.168.1.102/24')
#Routes=('192.168.0.0/24 via 192.168.1.2')
Gateway='192.168.1.1'
DNS=('192.168.1.1')
Results of 'netctl start mynet ; systemctl status [email protected]:
[email protected] - My net
Loaded: loaded (/etc/systemd/system/[email protected]; enabled)
Active: failed (Result: exit-codesder) since Tue 2013-07-02 23:33:03 EAT; 8min ago
Docs: man:netctl.profile(5)
Process: 6726 ExecStart=/usr/lib/network/network start %I (code=exited, status=1/FAILURE)
Jul 02 23:32:58 chanan002 network[6726]: Starting network profile 'mynet'...
Jul 02 23:33:03 chanan002 network[6726]: No connection on interface 'enp1s0'
Jul 02 23:33:03 chanan002 systemd[1]: [email protected]: main process exited, code=exited, status=1/FAILURE
Jul 02 23:33:03 chanan002 systemd[1]: Failed to start My net.
Jul 02 23:33:03 chanan002 systemd[1]: Unit [email protected] entered failed state.
Finally, since the wiki mentions possible conflicts, here's the output from 'systemctl list-units'. Hopefully there's nothing confidential in there.
UNIT LOAD ACTIVE SUB DESCRIPTION
proc-sys...misc.automount loaded active waiting Arbitrary Executable File Formats File System Automount Point
sys-devi...d-card0.device loaded active plugged 5 Series/3400 Series Chipset High Definition Audio
sys-devi...-enp1s0.device loaded active plugged NetLink BCM57780 Gigabit Ethernet PCIe
sys-devi...-wlp2s0.device loaded active plugged AR9485 Wireless Network Adapter
sys-devi...\x2d1.2.device loaded active plugged MFC-7420
sys-devi...ttyUSB0.device loaded active plugged E180v
sys-devi...9u1u3i1.device loaded active plugged E180v
sys-devi...ttyUSB1.device loaded active plugged E180v
sys-devi...ttyUSB2.device loaded active plugged E180v
sys-devi...ock-sr1.device loaded active plugged Mass_Storage
sys-devi...ock-sdb.device loaded active plugged SD_Storage
sys-devi...da-sda1.device loaded active plugged WDC_WD3200BPVT-22JJ5T0
sys-devi...da-sda2.device loaded active plugged WDC_WD3200BPVT-22JJ5T0
sys-devi...ock-sda.device loaded active plugged WDC_WD3200BPVT-22JJ5T0
sys-devi...ock-sr0.device loaded active plugged HL-DT-ST_DVDRAM_GT51N
sys-devi...y-ttyS0.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS0
sys-devi...y-ttyS1.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS1
sys-devi...y-ttyS2.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS2
sys-devi...y-ttyS3.device loaded active plugged /sys/devices/platform/serial8250/tty/ttyS3
sys-devi...et-ppp0.device loaded active plugged /sys/devices/virtual/net/ppp0
sys-modu...onfigfs.device loaded active plugged /sys/module/configfs
sys-subs...-enp1s0.device loaded active plugged NetLink BCM57780 Gigabit Ethernet PCIe
sys-subs...es-ppp0.device loaded active plugged /sys/subsystem/net/devices/ppp0
sys-subs...-wlp2s0.device loaded active plugged AR9485 Wireless Network Adapter
sys-subs...9u1u3i1.device loaded active plugged E180v
-.mount loaded active mounted /
dev-hugepages.mount loaded active mounted Huge Pages File System
dev-mqueue.mount loaded active mounted POSIX Message Queue File System
sys-kernel-config.mount loaded active mounted Configuration File System
sys-kernel-debug.mount loaded active mounted Debug File System
tmp.mount loaded active mounted Temporary Directory
cups.path loaded active running CUPS Printer Service Spool
systemd-...d-console.path loaded active waiting Dispatch Password Requests to Console Directory Watch
systemd-...word-wall.path loaded active waiting Forward Password Requests to Wall Directory Watch
avahi-daemon.service loaded active running Avahi mDNS/DNS-SD Stack
colord.service loaded active running Manage, Install and Generate Color Profiles
cronie.service loaded active running Periodic Command Scheduler
cups.service loaded active running CUPS Printing Service
dbus.service loaded active running D-Bus System Message Bus
dictd.service loaded active running Dictd Dictionary Server Daemon
[email protected] loaded active running Getty on tty1
iptables.service loaded active exited Packet Filtering Framework
[email protected] loaded failed failed My net
pacserve.service loaded activating auto-restart Pacserve
systemd-journald.service loaded active running Journal Service
systemd-logind.service loaded active running Login Service
systemd-...s-load.service loaded active exited Load Kernel Modulessystemd-...unt-fs.service loaded active exited Remount Root and Kernel File Systems
systemd-sysctl.service loaded active exited Apply Kernel Variables
systemd-...-setup.service loaded active exited Recreate Volatile Files and Directories
systemd-...rigger.service loaded active exited udev Coldplug all Devices
systemd-udevd.service loaded active running udev Kernel Device Manager
systemd-...e-utmp.service loaded active exited Update UTMP about System Reboot/Shutdown
systemd-...ssions.service loaded active exited Permit User Sessions
systemd-...-setup.service loaded active exited Setup Virtual Console
avahi-daemon.socket loaded active listening Avahi mDNS/DNS-SD Stack Activation Socket
cups.socket loaded active listening CUPS Printing Service Sockets
dbus.socket loaded active running D-Bus System Message Bus Socket
dmeventd.socket loaded active listening Device-mapper event daemon FIFOs
lvmetad.socket loaded active listening LVM2 metadata daemon socket
systemd-initctl.socket loaded active listening /dev/initctl Compatibility Named Pipe
systemd-journald.socket loaded active running Journal Socket
systemd-shutdownd.socket loaded active listening Delayed Shutdown Socket
systemd-...control.socket loaded active listening udev Control Socket
systemd-...-kernel.socket loaded active running udev Kernel Socket
basic.target loaded active active Basic System
cryptsetup.target loaded active active Encrypted Volumes
getty.target loaded active active Login Prompts
graphical.target loaded active active Graphical Interface
local-fs-pre.target loaded active active Local File Systems (Pre)
local-fs.target loaded active active Local File Systems
multi-user.target loaded active active Multi-User System
network.target loaded active active Network
paths.target loaded active active Paths
printer.target loaded active active Printer
remote-fs.target loaded active active Remote File Systems
sockets.target loaded active active Sockets
sound.target loaded active active Sound Card
swap.target loaded active active Swap
sysinit.target loaded active active System Initialization
timers.target loaded active active Timers
systemd-...es-clean.timer loaded active waiting Daily Cleanup of Temporary Directories
As you can see, it's late here and at my age, I turn into a pumpkin at midnight, so I'm off.  Any suggestions would be much appreciated.

Similar Messages

  • Problems to connect WLC after Firmware Update

    I have two WLC 4100, which just updated to the latest Software Version 3.2.193.5.
    Everything works fine, except I have problems connecting to the configuration Website.
    I have the following situation:
    My client is connected in VLAN A, there is also a Dynamic Interface configured in that VLAN A. The Management IP is configured in VLAN B. The Vlans are routed and gateways and so on are correct.
    The WLC is Layer 3 Mode.
    With the older software release I could connect to Interface IP in VLAn A or the Management IP in Vlan B.
    Now with the new software I cannot login on the interface IP on VLAN A anymore. Furthermore the Management IP on VLAN B is only "available" after I tried to connect to the interface IP on VLAN A.
    Otherwise the Management IP does not even answer to a ping.
    I am not quiet sure if this is a feature or a bug. Anyway it is very annoying
    Hopefully somebody has a solution or at least the same issue, so I do not feel so alone ;-)
    Thanks for your support

    I've seen something like this, too, on the WiSM when I had to enable telnet (ick) to run the LWAPP upgrade utility. It would not answer telnet on the maintenance port addresses (it even was nice enough to say so with a message) until after I had successfully telnetted to the corresponding management address. After that, it worked and I was able to run the upgrade utility. Same thing happened twice with two separate machines using the same address (at different times), so it's probably ARP related. Very strange. Don't know what to make of it.

  • Problems with Java AQ interface migrating 9i to 10g

    Hi!
    I've got problems with Java AQ Interface migrating from 9i DB, JDBC, AQ to 10g rel.2 DB, JDBC, AQ
    First, i started to occasionally receive NullPointerException in Oracle JDBC 9.2.0.8
    java.lang.NullPointerException
    at oracle.jdbc.driver.OracleStatement.describe(OracleStatement.java:6439)
    at oracle.jdbc.driver.OracleStatement.get_column_index(OracleStatement.java:6203)
    at oracle.jdbc.driver.OracleResultSetImpl.findColumn(OracleResultSetImpl.java:1557)
    at oracle.jdbc.driver.OracleResultSet.getString(OracleResultSet.java:1543)
    at gpnic.messaging.LDAPMessenger.messageFromRS(Unknown Source)
    We were using 9.2.0.8 JDBC and 9i and 10g databases.
    We decided to go up for 10g r2 JDBC Drivers, and 10.2 AQ but started to get the following errors:
    oracle.AQ.AQOracleSQLException: ORA-25216: invalid recipient, either NAME or ADDRESS must be specified
    ORA-06512: на "SYS.DBMS_AQIN", line 454
    ORA-06512: на line 1
         at oracle.AQ.AQOracleQueue.enqueue(AQOracleQueue.java:1267)
         at gpnic.comm.messaging.transport.AQTransportAdapter$AQDestanation.send(AQTransportAdapter.java:607)
         at gpnic.comm.messaging.transport.OutboundThread.run(OutboundThread.java:83)
    I'm specifying address of an agent, but oracle says I am not.
    I tried both native AQ and JMS interfaces, bot got the same error. I specify recipient the following way:
    'consumer' var contains name of AQ agent and is not null
    native AQ interface:
    aqSess = AQDriverManager.createAQSession(db_conn);
    AQQueue destQ = aqSess.getQueue(schema, queue);
    dequeueOptionsOut = new AQDequeueOption();
    dequeueOptionsOut.setWaitTime(AQDequeueOption.WAIT_NONE);
    dequeueOptionsOut.setConsumerName(consumer);
    dequeueOptionsOut.setDequeueMode(AQDequeueOption.DEQUEUE_REMOVE);
    dequeueOptionsOut.setNavigationMode(AQDequeueOption.NAVIGATION_FIRST_MESSAGE);
    AQMessageProperty mpOut = new AQMessageProperty();
    Vector vRecpt = new Vector();
    vRecpt.add(new AQAgent(consumer, null, 0));
    mpOut.setRecipientList(vRecpt);
    AQMessage aqMsg = null;
    AQEnqueueOption eOpt = null;
    //prepare message
    aqMsg = destQ.createMessage();
    CLOB chMsg = CLOB.createTemporary(db_conn, true, CLOB.DURATION_SESSION);
    chMsg.open(CLOB.MODE_READWRITE);
    chMsg.putString(1,msg);
    //creating oracle type message
    gpnic.db.SDSTypes.SdsMsgT oraMsg = new gpnic.db.SDSTypes.SdsMsgT(chMsg);
    AQObjectPayload payload = aqMsg.getObjectPayload();
    payload.setPayloadData(oraMsg);
    //setting properties
    aqMsg.setMessageProperty(mpOut);
    //do enqueueOut
    eOpt = new AQEnqueueOption();
    destQ.enqueue(eOpt, aqMsg); //<- here AQOracleSQLException is thrown
    JMS interface to Oracle AQ:
    TopicSession session;
    TopicConnection connection;
    TopicPublisher publisher;
    AQjmsAgent[] recipientList;
    connection = AQjmsTopicConnectionFactory.createTopicConnection(db_conn);
         session = connection.createTopicSession(true, Session.CLIENT_ACKNOWLEDGE);
         connection.start();
         Topic topic = ((AQjmsSession) session).getTopic(schema, queue);
         publisher = session.createPublisher(topic);
         recipientList = new AQjmsAgent[1];
         recipientList[0] = new AQjmsAgent(consumer, null);
    CLOB chMsg = CLOB.createTemporary(db_conn, true, CLOB.DURATION_SESSION);
    chMsg.open(CLOB.MODE_READWRITE);
    chMsg.putString(1,msg);
    //creating oracle type message
    gpnic.db.SDSTypes.SdsMsgT oraMsg = new gpnic.db.SDSTypes.SdsMsgT(chMsg);
    AdtMessage adtMessage = ((AQjmsSession)session).createAdtMessage();
    adtMessage.setAdtPayload(oraMsg);
    ((AQjmsTopicPublisher) publisher).publish(adtMessage, recipientList); <- here Exception is thrown
    We tried the following combinations
    9i DB, 9i jdbc, 9i aq - enqueue ok
    10g DB, 9i jdbc, 9i aq - enqueue ok
    10g DB, 10g jdbc, 10g aq - exception is thrown
    Can anyone help?

    Duplicate post, please check Upgrade 9i to 10g

  • Problem in configuring IPv6 interface with default  Router lifetime.

    I'm facing Problem in configuring IPv6 interface with default
    Router lifetime through a router advertisement.
    I'm also see an unusual behavior that even after configuring accept_rtadv=0,
    the ipv6 address is configured.
    Please help in out .

    Mac OS 9 does not support IPv6. While you can have IPv6 on your network, a Macintosh running Mac OS 9.2.2 or earlier cannot make connections to services using this network protocol.
    To use IPv6 on a Macintosh, you need Mac OS X 10.1 or later (as far as I know).
    —tonza

  • I am having Macbook Pro, I have recently tried updating my operating system to OS Yosemite, but after that its giving problem in connecting to Wifi. The error is "Connection Time out Occurred". Its getting connected by Ethernet cable.

    I am having Macbook Pro, I have recently tried updating my operating system to OS Yosemite, but after that its giving problem in connecting to Wifi. The error is "Connection Time out Occurred". Its getting connected by Ethernet cable.

    Take each of the following steps that you haven't already tried, until the problem is resolved. Some of these steps are only possible if you have control over the wireless router.
    Step 1
    Turn Wi-Fi off and back on.
    Step 2
    Restart the router and the computer. Many problems are solved that way.
    Step 3
    Change the name of the wireless network, if applicable, to eliminate any characters other than letters and digits. You do that on your router via its web page, if it's not an Apple device, or via AirPort Utility, if it is an Apple device.
    Step 4
    Run the Network Diagnostics assistant.
    Step 5
    In OS X 10.8.4 or later, run Wireless Diagnostics and fix the issues listed in the Summary, if any.
    Step 6
    Back up all data before proceeding.
    Launch the Keychain Access application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Keychain Access in the icon grid.
    Enter the name of your wireless network in the search box. You should have one or more "AirPort network password" items with that name. Make a note of the name and password, then delete all the items. Quit Keychain Access. Turn Wi-Fi off and then back on. Reconnect to the network.
    Step 7
    You may need to change other settings on the router. See the guidelines linked below:
    Recommended settings for Wi-Fi routers and access points
    Potential sources of interference
    Step 8
    Make a note of all your settings for Wi-Fi in the Network preference pane, then delete the connection from the connection list and recreate it with the same settings. You do this by clicking the plus-sign icon below the connection list, and selecting Wi-Fi as the interface in the sheet that opens. Select Join other network from the Network Name menu, then select your network. Enter the password when prompted and save it in the keychain.
    Step 9
    Reset the System Management Controller (SMC).

  • Netctl-auto cannot connect after unblocking wifi

    Hello,
    I'm using netctl as a connection manager. Systemd automatically starts "netctl-auto@wlp1s0" and if I boot system with wifi unblocked (rfkill) it is working fine. But when I boot my system with wifi blocked (from previous session) and after boot I manually unblock it (using rfkill unblock wifi), it doesn't pick up network. And when I try "sudo netctl-auto swtich-to <network_name> it prints out:
    WPA association/authentication failed for interface 'wlp1s0'
    It also happens when I'm working without connection with blocked wifi (for saving the battery) and then I turn wifi on - it also doesn't pick up a network.
    I have to first do:
    systemctl restart netctl-auto@wlp1s0
    which blocks wifi (when I try rfkill list, I can see that this restart blocked it) and only if I immediately switch wifi on (also using rfkill), it connect as usual.
    Does anyone experience same issue? Is it normal behaviour? Thanks

    I think you are seeing a manifestation of this bug.
    Note that I wrote that report.
    Last edited by ewaller (2014-03-27 15:01:50)

  • Problem in connection from SAP to XI

    Hi Guys,
    I have problem to connect from SAP to XI.  We have existing SAP R/3 (IS-H) and we newly installed XI. We decided to use ABAP proxy to send data from SAP to XI. When I go to SPROXY system showing ‘No Connection to Integration Builder’. Please kindly advice what configuration we need to in SAP side in order to connect XI.
    It’s Very Urgent. Please advice me.
    Thanks in Advance.
    Regards,
    Anil.

    Anil,
    could you please have a look to SAP Note 689847 - XI 3.0: SPROXY - No connection to the Integration Builder
    Cheers,
    -Sunil

  • Problem with connecting and syncing   (quicktime.qts)

    Hi,
    I have a problem with connecting and syncing my Iphone to itunes.
    iphone alone on PC -> uploading files (fotos) is possible
    itunes starts normaly, if iphone is not conected.
    if i connect iphone after starting itunes, or if i start itunes after connecting iphone i get an itunes-error with message:
    AppName: itunes.exe AppVer: 9.0.2.25 ModName: quicktime.qts
    ModVer: 7.65.17.80 Offset: 00909a47
    i test different things...
    - used another USB-port
    - used another PC
    - used macbook of my wife instead PC
    - deinstalled and new installed of itunes (older and newer versions) folow tutorials of apple
    - use another USB-Cable...
    I'm resigned, Please help me..
    Tom

    AppName: itunes.exe AppVer: 9.0.2.25 ModName: quicktime.qts
    In this context, that can sometimes indicate trouble with a content file on the phone (or Touch).
    Do you have any podcasts stored on the iPhone at the moment? If so, if you delete them from the phone, can you connect to iTunes without the error?

  • HT204053 I have a problem. I bought Pages and Numbers for my iMac and so far everything was OK.  Suddenly i have a problem with connection to iCloud. Dokuments created on iMac in Pages or Numbers are not transfered to iCloud. Not uploaded in iCloud.

    I have a problem.
    I bought Pages and Numbers for my iMac and so far everything was OK.
    Suddenly i have a problem with connection to iCloud.
    Dokuments created on iMac in Pages or Numbers are not transfered to iCloud. Not uploaded to iCloud. There is a sign  (small shape of iCloud), that they are waiting to be uploaded to iCloud.
    I think the iCloud is OK.
    i can see and manage documents in iCloud. i can create them on iPad and  see them and delete them in iCloud.
    But not on iMac.
    i dont know what has happened and I am not abble to find the solution. It was OK till some days ago….

    I have a similar problem! Everything stopped working after upgrading to Mac OS 10.8.4 through the App Store. Help!

  • I have problem to connect iChat. Sometime work and some time not working. When it was not working, there was a message on screen and said the mobile be server was not working. I needed to turn off computer and restarted the computer. Then it might. work

    To whom it may help,
           I use my iChat to do video chat with my granddaughter. I used to do iChat without any problem to connect with her in New York. However, After Mobil Me account closed, I accounted connection problems frequently. Sometime, I had to turn-off my computer then re-started the computer to make it work again. . When I had this problem to connect on iChat (the Mac did not allow me to choose "available"), the poped out window message said that " the iChat lost the Mobil Me account [email protected]" "The server connection was unexplected disconnect". Do you know what is my problem? My Apple ID for iCloud and previous Mobil Me account should be [email protected] I am no longer using [email protected] for Mobil Me e-mail address. My current iCloud e-mail address is [email protected] is no longer of using [email protected] account for my e-mail. If this is the problem, please let me know how to remove the [email protected] account from your system. Thanks!
    David

    SadisticIron wrote:
    i just baught my first iphone and it is a jalbroken
    Buzz! Thank you for playing!
    Discussing jailbroken devices is forbidden here by the Terms of Service.
    You can not get help here.

  • Problem with connecting to a website.  Just purchased a new iMac with Version 10.10.2 Yosemite.  Once in a while I have trouble connecting to a site.  It takes forever.  Is this an issue with Yosemite or my internet service?

    I purchased this iMac in Feb. 2015.  When I try to connect to a web site using Safari or Google Chrome I usually have no problems getting connected to the site.  But maybe once a day I will try to connect and I will see the blue progress bar at the top of the screen showing it is trying to connect and then it just stops.  It may take a couple of minutes before it connects to the site. 
    Would this be a problem with OS X Yosemite Version 10.10.2 ?  Or would this be a problem with my internet company? 
    Thank you,
    Laurie

    Hi lauriefrommi,
    Welcome to the Apple Support Communities!
    i understand that you have some intermittent webpage loading issues while using Safari on your Mac. In this situation, to ensure that Safari is working as it should, I would suggest reading over the attached article and using the information to make sure Safari has no unsupported third-party add-ons. 
    Unsupported third-party add-ons may cause Safari to unexpectedly quit or have performance issues - Apple Support
    Best regards,
    Joe

  • Problem with connecting to free wifi after upgrading to Windows 8.1 from Windows 8

    Hi
    I had problems with connecting to free Wifi after upgrading my PC(Notebook) to Windows 8.1 from Windows 8. As I travel a lot within europe, I am used to being able to connect to Free Wifi(those that dont need a key or password to enter) but soon after downloading
    Windows 8.1 I almost never was able to do this. I'd always get «LIMITED» even though the signal was strong.This was so fustrating,so much so that I reset my PC to clear it of Windows 8.1 and am now back to Windows 8.This is a shame because I was really liking
    using Windows 8.1 and if not for this problem(which is a big one) I'd still be using it. If I download Windows 8.1 again from the Windows store what is the probability that I'll have the same problems?
    Thanks Portozzygirl

    More often than not when a device isn't working it is because the driver has become corrupted. Re-installing a fresh copy should help
    http://windows.microsoft.com/en-us/windows7/Update-a-driver-for-hardware-that-isnt-working-properly?SignedIn=1
    http://captaindbg.com/how-to-update-drivers-on-windows-7/   (works on win 8 too)
    Wanikiya and Dyami--Team Zigzag

  • My iPhone 5 got problem when connect with lighting cable, this will keep pop up message "this accessory may not be supported"

    My iPhone 5 got problem when connect with lighting cable, this will keep pop up message "this accessory may not be supported", I can't charge or sync at all. I tried plug and unplug many time, still can't detect/charge my iPhone5, but sometime will 'lucky' that can connect to my iTunes and charge battery…
    This message will auto pop up also when I don't have plug anything in my iPhone 5, It is very annoying…
    The lighting cable is original and now i'm using OS 7.0.4 / iTunes is 11.1.3
    What I can do to fix this problem? Thank you.

    I would try using another cable you can likely borrow one to test from somebody
    if it's the same then likely the connector in your iphone have been damaged

  • After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

    After I've upgraded my iPhone iOS to 5.0.1, I got problems with connectivity. If my iPhone lose network, then it gets frozzen and I cannot make calls. After restart the telephone still does not work.

    1. Download the iOS 5.0.1: http://www.tobias-hartmann.net/2011/11/download-ios-5-0-1-veroffentlicht-direkte -downloadlinks/
    2. open itunes,Click in iTunes while holding down the Shift key (on Windows) or Alt key (Mac) to restore and firmware

  • I bought a new MacBook Pro (Mac Os 10.8.4) when conecting my mobile broadband dongle (Huawei E122) the computer does not read it at all. I do not have problems when connecting it to my former computer (PC) and a Mac from last year. Any suggestions?

    I bought a new MacBook Pro (Mac Os 10.8.4) when conecting my mobile broadband dongle (Huawei E122) the computer does not read it at all. I do not have problems when connecting it to my former computer (PC) and a Mac from last year. Any suggestions?

    Thanks,
    Yes, I did that. They have uppgrades for the dongles, but just untill Mac Os 10.7. Their solution is to buy a new modem from them or getting one for free if I sign a contract for 24 months! So, i think from that side not very helpful.
    It is just that I do not want to buy a new modem, when it works in quite recent computers and after having spent money in the new Mac.
    But thank you for your reply!

Maybe you are looking for

  • Hp laserjet 400 mfp can't scan, i lost the installati​on cd

    Hello, i have a hp laserjet 400 mfp and i can't scan. I have Windows 7 and the printer works just fine with the W7 software, but the scan option is not available, because the software installs only the printer, not the scanner. I lost the installatio

  • Color Correction Novice rounding home stretch w/ a Q

    Hi, So far, I've received some valuable advice & tips for my 1st attempts at color correction, esp since my production falls outside the normal applications. The help has been great! I went thru my production and did scene by scene corrections, which

  • Macbook does not boot to anything

    Previously my Macbook Pro 8,2 (15" Early 2011) was fine, but then it was not booting to Mac OS X, thus I removed the hard disk and test it, I found out that the hard disk was dead. I didn't had enough money to buy a new hard drive, so I put inside my

  • EIS load kickouts handling to an "unassigned" parent bucket

    Hello, a question for the Essbase EIS/AIS pros out there. Is it possible and if so, where in the EIS GUI could I specify where to drop a given dimension member record kickout during EIS the member load? For example, if I created an "Unassigned" paren

  • Flash 11.0.1.152

    Hey Guys. I recently updated my mac to the newest version of flash (11.0.1.152). Ever since then, my browsers, VLC, anything that uses flash hangs up and never loads. I know its flash cause when it was installed, I went into activity monitor and quit