New /etc/conf.d/network network configuration does not work.

I did some work to upgrade my system configuration according to
this wiki article: https://wiki.archlinux.org/index.php/Rc.conf
But when i move the network configuration from rc.conf to
conf.d/network, my network is left unconfiguered after boot.
My /etc/conf.d/network looks like this:
interface=eth0
address=172.20.247.67
netmask=255.255.254.0
broadcast=172.20.247.255
gateway=172.20.246.1
Possibly related, /etc/resolv.conf is replaced after boot with this content:
# Generated by dhcpcd
# /etc/resolv.conf.head can replace this line
# /etc/resolv.conf.tail can replace this line
and therefore, my nameserver configuration is gone. This also happens,
when i leave the network configuration to rc.conf. It happens, since i
fiddled with rc.conf, but i don't no why.
I have not yet switched to systemd because of these problems.

Read up here on how to set up your static IP. https://wiki.archlinux.org/index.php/Dh … IP_address Dhcpcd doesn't use your /etc/conf.d/network by default
Last edited by piratebill (2012-12-03 19:00:13)

Similar Messages

Updated my iPhone to new iOS6 and my Memory Loader app does not work! Is there a fix for the problem as it seems I am not the only one coming across this issue?

Updated my iPhone to new iOS6 and my Memory Loader app does not work! Is there a fix for the problem as it seems I am not the only one coming across this issue?

Other than what you have already done, you should clear the cache from your browser and, if you use it, your Facebook app. Also, deleting old texts can free up some room.

CuciLync 9.2 - registry key configuration does not work as expected

Hi,
according to the Administration Guide for CuciLync 9.2.2 some registry keys are supported to configure the client.
In the chapter 'Phone Parameters' there is a statement that four registry keys are supported:
CcmcipServer1
CcmcipServer2
TftpServer1
TftpServer2
In the next chapter 'CTI Load Balancing' there is an explanation that the registry key UseCUCMGroupForCti is also supported.
=> Does that mean that five registry keys are supported and not only four ?
My next questions leads to the possible values for these registry keys.
With CuciLync 8.6 it was possible to leave the registry keys for CcmcipServer empty.
In this case the IP addresses for CcmcipServer were automatically defined by downloading the config file.
And with UseCUCMGroupForCti these IP addresses were 'copied' to CtiServer.
That means with CuciLync 8.6 there was need to define CcmcipServer and CtiServer.
Only the TftpServers were configured by registry keys.
=> Is this also supported with CuciLync 9.2 ?
=> If no: In which future version do you plan to implement this ?
=> If yes: Are there any extra settings needed ? Because it does not work at the moment
Thanks for your feedback
Best Regards
Carsten Lucy
(Bayer Business Services)

According to MSDN:
When caching is enabled, the module caches the service information data until it polls the Service Control
Manager and discovers that the data has changed. If changed, the module updates the cached data and returns it as output. You can disable this caching feature, but doing so will cause the module to return data at every polling interval instead of only returning
when the data has changed or when the polling interval count has reached a multiple of 10.
However, the configuration is DisableCaching, and the default is False. Go figure that one out. Gotta
love Microsoft configuration names and documentation! If true, then it's not disable..... :)
Jonathan Almquist | SCOMskills, LLC (http://scomskills.com)

Installed new version of Firefox, now scroll wheel does not work

Installed new version of Firefox, now my scroll wheel does not work. I need this fixed immediately or will be forced to abandon Firefox as my browser. Can anyone help? I saw some Q&A on this but no definite fix. Thanks!
== This happened ==
Every time Firefox opened
== Immediately after I installed

I have the same problem, plus more. I cannot click on a button, does no good. I have been using 3.01, would never upgrade; always had a problem since 3.5. Now I upgrade to 3.66 figuring the problems were over, wrong. No scroll wheel, no buttons, cannot close half the windows, cannot go to a bookmarked page. Did Microsoft take over Mozilla? If I wanted a junk browser, I would use IE. I want the Firefox that it used to be; stable, reliable. What happened? Only way I can get Firefox to work is in safe-mode.

New Intel WIFI Wireless Network Adapter does not recognize Wireless Router

I have had a Linksys BEFW11S4 Version 4 Wireless router for quite some time. It works like a champ and I have one Laptop wired to it and a second using Wireless working just fine. Recently, I received a new ThinkPad W500 Laptop with an Intel WIFI Link 5100 AGN wireless network adapter. The older laptop that works just fine with the router uses a
11a/b/g Wireless LAN Mini PCI Express Adapter by Atheros. However, the NEW laptop with the Intel Adapter fails to connect to the Router. It will either indicate a failure while "Waiting for Association" or it will indicate a failure when waiting to "renew IP Address". Sometimes, it will show a signal strength close to ZERO (Even as the older laptop with the other adapter is showing a signal strength close to 100%) When I called Linksys support, I was told that the facts that the Router (a) works find with the wired Laptop and (b) works fine with the 11a/b/g NEtwork Adapter and (c) works fine when WIRED to the new laptop all indicate that the problem is NOT with the router at all -- but with the Network Adapter. Can anyone tell me what has to be adjusted in the Adapter settings? Right now, I am using IBM Access Connections for BOTH of the wireless laptops. I have made sure to set IDENTICAL values for SSID and WEP (128-bit) [static] password. I have also ensured that all OTHER settings are the same for the two laptops. Yet, in one laptop, there is NO PROBLEM while in the other, I can not get the Wireless Adapter to "see" the signal from the Router. TO further check this, I have [temporarily] disabled the WEP password, enabled SSID broadcast, and disabled the MAC address restrictions that I put in (so that the system would be totally "open") yet the Intel Adapter STILL did not "find" anything. In addition, when I use the "Find WIFI" feature in Access Connections, I find that SOMETIMES the network with SSID is found and sometimes, it will display "unknown network" and not pick up the SSID.
This is all very frustrating. If anyone has experience with the Intel WIFI Link 5100 AGN Adapter, I would appreciate any hints, tricks, ideas, etc.
Think you!!!!
--Zvi

I installed the LATEST version of IBM Access Connections as well as verifying that I have teh LATEST drivers for the Intel Wireless NEtwork Adapter.
What now happens is that I am able to authenticate to the Router. However, I get a failure on "renewing IP Address" -- which [according to the diagnostic message] means that the Rotuer fails to provide me with an IP address to use. Do you have any suggestions?

HP Officejet Pro 8000 A809a - network connection does not work

Hi,
I just purchased the Officejet Pro 8000 (without wireless). Printer works great when connected and installed via USB, but network connection is just ... awkward. Meaning it doesn't want to work
Question: when I connect the printer via ethernet, the printer should automatically obtain an IP-adress from my router's DHCP-server, right?
Well that doesn't happen here. I printed the network configuration page several times, each time it states that the printer has the IP 169.254.90.4 with 255.255.0.0 as subnet. My local network is 192.168.2.0 with 255.255.255.0 as subnet. So the connection to the printer cannot work. Why doesn't the printer automatically obtain the network config of my network and how can I change this behavior?
Any help would be very appreciated.

Sometimes DSL providers have more control over the router than the printer likes.
- Unplug the telephone line and printer's Ethernet from the router.
- Turn the power off on the router, wait 30 seconds, then turn the power back on.
- Connect Ethernet between the printer and router.
- Now find the IP address of the printer (it should be on the self-test printout), type it into a browser.
- In screen you will find a Networking Tab, then on the left Wireless, then the IPv4 Tab.
- On this screen you want to set a Manual IP. You need to set an IP address outside the range that the router automatically sets (called the DHCP range). If you know what that is, set an IP outside that range but no higher than 255 (the last number in the address).
- Use 255.255.255.0 for the subnet (unless you know it is different, if so, use that)
- Use the router's IP address for the gateway and the first DNS (leave the second blank).
- Finally, plug in the phone line and test.
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

ATT hooked up new u-verse router, now time capsule does not work and airport utility does not see it ?

ATT hooked up the new U-verse router replacing the older 2wire router. Old 2wire router worked fine with Airport +Time Capsule. Now only the amber light flashes. When I try to reconnect with Time Machine it does not find the Time Capsule nor does the airport utility find the Time Capsule. Any help?

Okay, the 3801HGV also doesn't bridge - but there is a workaround. Info on the workaround comes from 'SomeJoe7777' at this link:
http://forums.att.com/t5/Residential-Gateway/U-verse-for-BUSINESS-2Wire-3600HGV- bridge-mode-or-another-AT-amp/td-p/2707013
As for connecting to your TC: the 3801HGV uses a default IP address of 192.168.1.254. It passes out IP addresses to your networked devices, and all of those IP addresses will be 192.168.1.something. The TC uses a default IP address of 10.0.1.1. As your primary router, if the TC's defaults weren't changed, the TC would be handing out addresses to your networked devices that are 10.0.1.something.
If your computer has an IP address of 192.168.1.something, it won't be able to see the TC if the TC's address is 10.0.1.1 (or anything else that's not 192.168.1.something). Hopefully that makes sense!
Go into System Preferences on your Mac, and click the Network icon. Click on Ethernet on the left side, and you'll be able to see what IP address your Mac has been given. My guess is that it has a 192.168.1.something address from the 3801HGV.
If I'm right about the 192.168.1.x address, and that your TC is running with 10.0.1.x addresses, then that's why your Mac can't see your TC. In this case, you need to change the Mac's Ethernet setup to manually set your Mac to a 10.0.1.x address for the TC to see. To do this, go to System Preferences, then Network, then click Ethernet on the left side.
Set the Configure IPv4 dropdown to 'Manually', and it will open up some places for you to fill in information:
IP Address: 10.0.1.15 (or a similar number that won't conflict with your TC's address, but starts with 10.0.1)
Subnet Mask: put in 255.255.255.0
Router: 10.0.1.1 (I'm assuming here that your TC was running with the default IP address; if it was something different, then set Router to whatever IP address your TC was using.)
Then, click the Apply button to make your changes active.
Now, since your Mac's IP address will be in the right "subnet" for your TC, they should be able to see each other. (It's kind of like having to live on the same block as someone to be able to talk with them. In general, if your computers don't have similar addresses, they can't talk to each other. Of course that's simplified greatly, but you probably get the idea...)
Once you've got the IP addresses matched up, you should be able to see your TC. At that point, you can update the TC to work with the 3801HGV. I recommend setting it to bridge mode, but if you can follow SomeJoe7777's advice, go for it!

Transfer account from old MBP to new one and now my account password does not work.

I trasferred my account from one MPB to a new one using targeted disk method. I left my desk while it finished and came back to a registration page. I registered and the system rebooted. Now I see my login details but the password form my old Mac fails. The hint it gives me also seems to be bogus becaues I've tried many variations of the hint and they also do not work.
I'm submitting this from my original MBP and had not problem using my old password logging in to it. Why didn't my password transfer properly and now how do I fix my new MBP?
I made sure duing the transfer process to select everything for transfer -- accounts, applications, etc. All check boxes were checked.

AKAspuds wrote:
I trasferred my account from one MPB to a new one using targeted disk method. I left my desk while it finished and came back to a registration page. I registered and the system rebooted. Now I see my login details but the password form my old Mac fails. The hint it gives me also seems to be bogus becaues I've tried many variations of the hint and they also do not work.
I'm submitting this from my original MBP and had not problem using my old password logging in to it. Why didn't my password transfer properly and now how do I fix my new MBP?
I made sure duing the transfer process to select everything for transfer -- accounts, applications, etc. All check boxes were checked.
So now you have 2 accounts, logout of this one and in to the other.

Networked printer does not work under bonjour

I run a 50-computer network with 10 printers, all running bonjour. Servers and clients all 10.3 and 10.4. I just installed 10.5 on my computer to test. It appears that none of the network printers (mostly Lexmarks) no longer work with bonjour, only direct IP printing.
Does anyone have solution for this?
Since when is Apple trying to become Micro$soft?

10.2 - 10.4 did not use Bonjour for Mac to Mac printer sharing though 10.5 does. This article describes the issue:
http://docs.info.apple.com/article.html?artnum=306984
I hope this helps.

E-studio 160 network printer does not work correctly in my office network

Hi Toshiba support team,
I'v got a Toshiba e-studio 160 network printer/scanner/fax in my office and I want that everybody in the office (network) has access to the printer and scanner functions of the e-studio without using a "Server computer" which should be connected to the local parallel port of the printer. In other words, the printer is connected over TCP/IP and a suitable RJ45 cable to my main-switch in the office.
The printer in configured with a valid IP-address but in my office I havn't got any WINS-server, so this configuration field is empty and unused. I tried several different methods but I can't get access to the Printer via TCP/IP. Just the "PING" command works correctly. I expected that the printer will appear in the Windows-File Sharing Folders, but it doesn't. By the way, all my computers are equipped with Microsoft Windows XP. I read somewhere in a board that a guy fixed this problem by using a program called "P2P" but I couldn't find something like this.
With the original Toshiba drivers it is only possible to operate this printer local or over a Windows Print-sharing function but I don't want that one machine is running all the time.
I hope anybody can help me with my issue.
Best regards,
Michael

Since this is a forum only for Toshiba notebooks and Options, I doubt someone will be able to help you.
But I found a special Toshiba page for Printers and Copiers.
http://copiers.toshiba.com/support/index.jsp
Maybe you will find some details there.
Good luck

Networked L7680 does not work from more than one computer at a time.

Have installed latest driver software on both computers. Printer will only work with one computer on at a time. When I run windows device trouble shooter from the last computer turned on it says printer is off. It works ok from the first computer turned on.
Any help is appreciated.

Networked how?? Please explain how everything is connected and model number of equipment.
Say thanks by clicking the Kudos Thumbs Up to the right in the post.
If my post resolved your problem, please mark it as an Accepted Solution ...
I worked for HP but now I'm retired!

Network adapter does not work

How do I replace network adapter for Model p6370t, Product No. AZ210AV, Window 7 Professional operating system? It quit working after a power surge caused by a close lightning strike. It appears that this was the only damage. I can get on the internet using a wireless adapter and router. I would like to use a wired connection.
This question was solved.
View Solution.

You will have to purchase a PCI Express x1 network adapter card to install in one of the slots in your motherboard.
Tere are quite a few available on this web document at NewEgg.com. You should also be able to find one at any local PC or electronics store.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

New MBP logic board and wireless internet does not work anymore

hi there
i had to change the logic board in my only 2 years old MBP15". i purchased a new one and put it in by myself (relatively easy task). i still use the same internal HD as this one still works fine, so all data are the same.
however, the new logic board has obviously a different "identity" from my old one, it came with a sticker which says "ethernet ID 001FF3513E7A" which is different from before. this may be the reason i can still access my wireless network at home, but the self assigned IP address prevents me from connecting to the internet. all settings are as before and it worked always without a problem.
all settings were "automatic" before (using DHCP), and i use exactly the same settings again, but no success. i have to add that i use a new mac mini in the same network with absolutely identical settings (automatic) and this one receives a free IP address from the router (which is only in the last number different from the router's), but the MBP shows a totally different IP address.
i could finally fix it switching to "manual" and adding the same IP address the mini is using and just changed the last number, which has to be different from the time capsule i use as wireless device and the mini. like this everything works just fine.
but why does the mac mini perform everything automatic and the MBP (even with the new ethernet ID - and especially since i connect wireless and not using ethernet) is not able to do so?
i worry if i want to use the internet in any wifi hot spot i may run into troubles...
any idea what the difference between these two machines (with identical settings) is?
thanks and cheers
george

Thank you. It didn't work unfortunately :((
Here are my router's details (Huawei):
Product name HG655b
Device ID 00E0FC-21530307237S0B028701
Hardware version VER.C
Firmware version V100R001C02B018
Batch number RWC3P0.010.29066
Physical address 5C:4C:A9:A5:41:B0
System up time 0 days 0 hours 15 minutes 56 seconds
I don't have Mac filtering enabled.
Now it doesn't even find the wireless network anymore...
My computer and itouch are connected to WAP, but the iphone could not connect to WAP, but only WEP.
Any other ideas?
Thanks a lot!

I´ve bought the new IPad3, what a disappointment the 3G does not work, no Internet available, APPLE what are you doing for the all the people in Germany who bought the new IPad3? I´m still an Apple fan, all my products are from Apple but I need a solution

I have been waiting since months for the new IPad4G 64 Gbt. ON recommendation of Apple Support I have changed my IPad 4G last week in the hope that something was wrong with the firts one I bought.
The one I have now has the same problems. WiFi is working however 4G not at all. Apple what can I do? What are you doing for the thausands of German Apple fans who have bought a IPad4G and can not use it. We need a solution NOW. I´m working with this tool and need to be able to rely on it.
Thanks for a feed back.

JKerki wrote:
They had not heard about the problem, however made no problem to change it for an other one. Apple Support Germany pretendet not to know about this problem. However the web is full of complaints.
It would be advisable for Apple to react officially on it. € 799, - for something that doesn´t function is no fun :-((
Isn't replacing your iPad Apple "officially" acting on it?

I installed a new bigger hard drive and now spotlight does not work with outlook to search for emails

My old hard drive was full so I went to an apple authorized provider to install a new bigger hard drive. They also moved the data and applications from my old drive to the new one. They did not use time capsule because their way was faster. After the installation I did have to reenter the product code key for Office 2011 for the Mac. However, now I find that I cannot do email spotlight searches in Outlook. When I put in the search - it comes up with no results. This is true no matter what the search. Any ideas of how to point spotlight to look in the email folders so I can do searches again. This is a feature I use daily - so I am concerned that I have lost this feature. Also, I am noticing that alot of the settings did not carry over to the new hard drive. Any help is greatly appreciated!

I would recommend starting over and migrate using your Time Capsule backup however DO NOT do it wirelessly, connect using an Ethernet Connection. If you upgraded to Lion from Snow Leopard then follow the instructions in this video, the kid is annoying but he knows what he's doing. Clean Install Of Snow Leopard video. Once you have installed and updated Snow Leopard then update using the 10.6.8 Update Combo, then log into the Mac App Store and re-install Lion and all it's updates. My guess this is an afternoons work.

New /etc/conf.d/network network configuration does not work.

Similar Messages

Maybe you are looking for