New printer, same ePrint mail, not possible

Hello everyone,
I've recently installed an 8600+ to replace my 6600.
Before uninstalling the 6600 I went on the ePrint portal, change the 6600 mail address, remove it from the portal, deleted it on my computer and finally physically moved from my office
Afterwards I installed the 8600+, set the IP as fixed so I have no problem with the scanner, I've enabled the ePrint functionnality and received a RNG mail so I can add the printed on the web portal, everything is OK.
The problem is that I want to change the ePrint mail address of the 8600+ and came back to the one I had for the 6600, but this is simply not possible, it says that the mail is not available.
Is there a way to solve this problem?
Best regards

Ok, seems the answer were post on other thread at the moment I'm writing mine... Sad to see there is no solution.

Similar Messages

Batch to batch transfer of same material is not possible

We are doing batch to batch transfer of same material no. through MB1B in a plant which is depot. This is not happening and error message is coming "Batch to batch transfer of same material is not possible" msg no. 00398.
We tried the same transaction in mfg. plant and it is allowing the batch to batch transfer of same material no.
Full marks for earliest best solution.

Choubey Ji
Normally when you want to do stock transfer and change the batch of a material then we use M Type 309 via MB1B...in your case..you are doing this within a single plant...which i don't think is possible.
Correct me if i am wrong.
Regards,
N

I am trying to install a new printer and I am not sure which application to use?

I am trying to install a new printer with the external CD rom drive on my MacBook Air. When I load the disc it is not allowing the program to run as it is stating that I have the wrong application to do so. How do I install things from the external CD Rom?

What model printer is it?
It is unlikely you need its installation CD-ROM at all.
Mac 101: Printing (OS X Lion)

Officejet 4622, new printer today. black does not seem to work at all but all the colors do.

I print a test page through diagnostic tool and black square is blank. I cannot tell if the alignment prints properly as I have no example of what it should look like to ensure it is correct since the alignment fails to detect the alignment page. Scans work fine. I tried cleaning the print heads and still don't seem to get black to work correctly. This is a new printer purchased today 9.30.2012.

just in case anyone else encounters this problem, heres whats really going on and heres how to fix this annoying issue. its relatively easy to do and more efficient than wasting money on a new printer or having it repaired like most people end up doing.
whats going on? the ink has clogged the printing heads and has solidified shut. the "clean print heads" feature the printer came with does not have the ability to fix this. that feature is to clean up dirty heads, not clogged heads. why hp decided to make this model without a simple to remove cradle is beyond me, but fortunately the cradle DOES come out and can be cleaned with hot water.
theres a few items you will need to make this happen the easy way or you could just break out the tree limb loppers, like i did, and vent your frustrations.
what you will need: a pair of needle nosed pliers, a T9 torx screwdriver head ( auto parts stores sell them for a couple bucks), some paper towels and an area to work (its easiest to do this in a corner of a room, on a small table or the floor). keep in mind you are dealing with ink, so change out of your good clothes just in case and also grab a paper plate or a few sheets of printing paper to set the ink cartridges on as you work.
1) ok. lets get started. !!!FIRST UNPLUG THE PRINTER RIGHT NOW, SO YOU DONT ACCIDENTALLY DIE BY ELECTROCUTION!!! i forgot and when i began unscrewing the first 6 screws, the chime kept going off and im like **bleep**? i was impressed by the safety measures hp took while engineering this model.
2) the printer is now unplugged and then go to your corner work area and place the printer so there is a wall or barrier on its left and also a wall or barrier behind it. do this while facing it as if you were about to use it.
3) now, what you have to do is open the printer like you are going to change the ink and on the right side there is a plastic guide that prevents the top from opening all the way. look on the side and you will notice it could pop off with your fingers. pop it off and open it all the way open so you could get at the screws the lid would have prevented you from accessing.
4) lean the scanner portion and top portion against the back wall.
5) all screws you will be removing are size T9H torx screws. there are ten total. there are 2 black screws in the front top and then 4 black screws in the back top. remove them and put them on your paper plate.
6) next is 1 short silver colored screw located under the control panel, use your finger and feel around beneath the * button. unscrew it, put it on the paper plate.
7) next you are going to remove the face/control panel to get at the last 3 screws so locate the little illustrations on the top of the printer, there are 2 on the bottom left and 5 on the bottom right (1 and 2 on the left explain paper jam removals and then 1-5 on the right explain changing ink cartridges). then about half an inch south of the number 5 illustration, on the lip, is a plastic bracket. six inches to the left is another one then 6 more inches to the left, under the illustration number 2 (paper jam removal) is a third bracket. undo them using your fingernails. and just flip it up like car hood and then lay it down on the main top portion of the printer, minding the flat wire which is connected into the circuit board of the control panel (if the flat wire popped out because you got too rowdy on it, then simply insert it back in when you reassemble).
8) next, unscrew the 3 longer silver screws which are located under the panel you just popped off. there is 1 on the left and 2 on the rightish side. toss em on the paper plate.
9) now that all the screws are removed, take the face panel and partially pop it back together.
10) then take the whole top ( the part with the little illustrations and lift it like a car hood, ONLY THIS TIME OPEN IT TO THE LEFT and balance it on the edge of the printer, leaning it towards the wall or barrier on your left. BE CAREFUL NOT TO YANK ON THE FRUIT STRIPE COLORED WIRES ON THE LEFT AND ALSO THE BLACK FLAT WIRE THAT CONNECTS THE SCANNING PORTION TO THE MAIN PORTION OF THE PRINTER.
11) next grab the needle nose pliers and remove the 2 silver colored tension springs located behind the printer cartridges. pay attention where they were attached so you remember where they go during assembly. take a pic with your phone if you have to or simply re-figure it out like i did. toss em on the paper plate.
12) then disconnect the 2 large flat wires and 1 small flatwire attached to the back of the ink carriage. take a picture or remember like i did. i imagine bad things may occur if you reverse them on re-assembly. grab the phone and take a quik pic to be sure.
13) now remove the ink carriage, cartridges and all, by lifting the front first. be careful of the little transparent ribbon in there that moves the carriage left to right and vice versa. you dont want to damage that little guy. now take the carriage to your paper plate. dont drip any ink or accidentally get it on your fingers without knowing or you will make a mess.
14) remove the ink cartridges and set them on the paper plate, ink side up to avoid a mess, these things sometimes drip. set the plate off to the side. its time to clean the print heads.
15) then go to the sink, with the empty ink carriage and turn the water on hot and then just let the empty ink carriage sit there with the water mainly going through the screen of the clogged color (inspect and make sure there isnt a little rubber gasket surrounding the little screen if there is dont lose it. i didnt look too closely and i dont think hp has them but i know some other printers do). it wont stain the sink but wash down any ink as it comes out to be sure. also notice there is a small circuit board attached to it. dont bang it up but getting it wet doesnt matter.
16) keep doing this until the water runs clear.
17) then use your finger and rub the screen gently with your finger and then rinse it, washing away the ink until the water runs clear. continue this until there is no more ink and the screens are clean. do it to all the colors just for good measures. the problem color that wouldnt print, you will notice takes longer to clean than the other colors.
18) now look on the bottom side of the carriage. those wierd looking things are the heads. rinse them with hot water and wipe them with paper towels. then flip it over and blast the screen side again. also in between the screenside and the heads (on the side of the carriage) is an opening that is also probably gunked up. blast it with water too. then flip it over and wipe the heads again. repeat this step until nothing wipes away or until you are sick and tired.
19) shake off then use paper towels to dry the entire unit. make sure the unit is dry. especially inside the female plugs. blow in it or break out the hair dryer and gently dry it. dont sit there and melt it though with the blow dryer. but the sooner it dries the less likely your ink cartridges sitting on the paper plate will dry out. the ink wont dry out fast just dont take a nap or go out on a date until you are reassembled with the ink portion.
20) now you have completed the cleaning of the heads and probably wont need to do this again for the length of time it was since you bought the printer. and just like a roadtrip you used a map to navigate, you will use these instructions in reverse for re-assembly. but keep in mind when re-inserting the 3 flatwires you disconnected from the back of the ink carriage, make sure you have the little metal contact points on the flatwires (male side) inserted so they touch the little metal contact points on the carriage plugs (female side). ALSO BE EXTRA CAREFUL NOT TO DAMAGE THE BLACK FLATWIRE CONNECTING THE SCANNER PORTION TO THE MAIN PRINTER PORTION. THERE IS A LITTLE GROOVE IN THE PLASTIC WHERE IT CAN BE SEATED TO GUARANTEE NO CRIMPAGE. USE IT. also make sure the 2 hinges of the scanner portion/lid are seated properly before fastening the the top with the 6 black screws.
now re-assemble the printer and reinstall the ink cartridges. and then plug in the unit, and turn it on. if you get any notifications on the control panel saying the carriage wont move, then open the hood and take out the ink cartridges, push around and make sure the carriage is seated properly and that the tensioner springs are in place properly. repeat if neccesary until notifications go away or just do a test print and disregard the notification if you messed with it already a few times. thats what happened to me and the notification went away on its own. once its online, open the hp utilities and press the "clean the heads" button. do it 2x in a row and you will be back in style, with extremely rich and bold colors and yes, raven black print.
p.s.
you can always take your aggressions out with the tree limb loppers or the tin snips like i did and snip out the center plastic that prevents you from taking the carriage directly out. this eliminates disassembly and re-assembly entirely. just make sure you DO NOT CUT THE TRANSPARENT RIBBON THAT MOVES THE CARRIAGE BACK AND FORTH. this way the next time it happens it only takes you 10 minutes before you are up and printing.
enjoy! - Porf

TS3899 just got my 5c transfered everything over to new phone but my mailis not connecting

just synched old sim to new sim for new phone but cannot get into mail please help

I think you may have the process confused. You do not sync anything to do with the SIM. If you sync your phone via the iTunes process and sync over the email settings, the one thing that does not sync is the password. You need to go into the mail accounts in settings and enter your password. To receive mail, you need to go into the Incoming Mail server settings, to send mail, it is the outgoing or SMTP server. Did you read through the support document that you linked to the forum with?

Open bookmark results in "new tab". More is not possible!

[]Opening a bookmark or entering a web address does not work.
The result is only: "New tab".
Also opening in the Firefox Help menu results in "New tab".
By clicking on "New tab" nothing happens!

Can't you open any web page or do you only have that problem with bookmarks?
Issues with bookmarks or history not working properly can be caused by a corrupted file places.sqlite that stores the bookmarks and the history.
* http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
A possible cause is security software (firewall) that blocks or restricts Firefox or the plugin-container process without informing you, possibly after detecting changes (update) to the Firefox program.
Remove all rules for Firefox from the permissions list in the firewall and let your firewall ask again for permission to get full unrestricted access to internet for Firefox and the plugin-container process.
See:
* [[Server not found]]

New computer same ipod ipod not working

I recently purchased a new laptop. It has been authorized (after several attempts because the "iTunes Store was unavailable") and now my iPod, which I have had for several years and has successfully been working no longer properly syncs with the new laptop.
When I synced iTunes told me that audiobooks that I had on the iPod and was listening to no longer worked with the iPod. This makes absolutely no sense. They worked on the iPod earlier this week before I synced it through the new laptop. How do I recover the ability to listen to songs and books that previously had no issues on my iPod?
I have also lost all of my playlists, this has never happened before and I have changed computers several times with this particular iPod.

Peter,
Welcome to Apple Discussions.
First: It is not safe to have your music on your iPod only. iPods do fail sometimes and would leave you with an empty iPod and no music.
That said, it is possible to get your tunes of your iPod. You don't mention your OS but you may find an utility for this on versiontracker.
iPod Agent (windows).
Senuti (Mac).
JJ
Don't steal music !! Just a statement, not an accusation

Sending Mail not possible

Re-installed Mail and imported Mailboxes, with minimum hassle. Now cannot send mail. Message stays in Outbox. Why not in Draft ?. Message now reads ...The SMTP server does not support SSL on Port 25..
when trying to send a mail. Checking with my ISP, I was able to send & receive mail on their web server.
Repaired permissions, Run Applejack etc. Dumped Mail caches and Envelope index on Desktop.
Any clues or suggestions welcome.

Clues...
The receiving email ports are:
IMAP is port 143
IMAP-SSL is port 993
POP is port 110
POP-SSL is port 995
SMTP and SMTP-SSL is on ports 25, 587 and 465. Port 587 has to be SSL, and port 465 is enforced TLS-wrapped and is generally used by Outlook users.
Try ports other than 25.

Export With Same Pixel Size Not Possible?

I'm exporting two photos from Aperture to another program for the purpose of creating one panoramic picture.
However, the other program (PFactory) only allows the stitching of photos with the exact same pixels and no matter how I try to export both photos with same pixels using Fit Within Pixels with Aperture they never come out the other end the eact same size.
One photo has 5195 x 3454 and the other has 5195 x 3459.
Anyone know why?
Thanks.

How are you trying to do this now? When you export using a "fit within" it's going to scale the image proportionately. It's not going to crop. The problem you're having is that the ratio of height to width of these two images doesn't match so "scaling" wont work... if it trims the height by a few pixels it's going to trim the width by a few pixels to maintain the aspect ratio.
You'll have to crop the larger image by 5 pixels. But this is what I had assumed you (or someone) had already done to the 2nd image. I've never seen a digital camera that puts out images in random sizes (were the images actually taken with the same camera on the same settings??)
Select the larger image, pick the 'adjustments' tab, click the 'crop' icon along the bottom left corner of the image frame. In the crop-window that opens, set the "Aspect Ratio" to "Custom" and then type in the dimensions that you want. It'll put a box on the screen to show the area it intends to keep but you can use your mouse to slide that box around. When you leave the crop mode (e.g. pick the "selection tool" icon (left-most icon in the lower left corner of the image -- or really any other mode) the image will be updated to reflect the crop (keep in mind Aperture doesn't really crop the master... it's just displaying it that way.)
Now when you export to TIFF or JPEG, etc. as "original size" the image sizes will match.

Outlook 2010 additional account same server - mail not sending

Hi,
I have setup a new domain (child.domain.local) and a second mailbox for the boss on our Exchange 2010 server. I have created a new User account in the new domain for him and a new mailbox in Exchange. I have given Send As and Full Access permission
on the new mailbox to his original user account ([email protected]) and added the new mailbox as an additional account in Outlook 2010.
The new mailbox is visible in Outlook with emails addressed to the new email address but when trying to send from the new email address the email just sits in the Outbox, despite sending and receiving completing fully with no errors.
Any ideas what I am missing please?
Also, I have disabled the new user account in ADUC in the new domain ([email protected]).

Hi Tippers,
Sorry for the late reply.
Yes, you are right. OWA works well but Outlook not, it seems like an issue on the Outlook Client side.
Our emails stuck in Outbox without errors, this problem is likely to be related to our local Outlook configuration.
If Outlook is not sending only some Outbox emails, please make sure we don't have the habit to preview/open/click on Outbox emails.
If Outlook is not sending any of our Outbox emails, please try one of the following methods:
1. Please make sure Outlook is not set to the Offline mode.
2. Run Outlook under safe mode to avoid some AVs, add-ins and firewall.
3. Our Outlook data files may be corrupted. Please performing a data file scan via Outlook ScanPST tool.
More details in the following article:
Outlook is not sending email – stuck in Outbox
PLEASE NOTE:
Microsoft is providing this information as a convenience to you. The sites are not controlled by Microsoft. Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there. Please make sure
that you completely understand the risk before retrieving any suggestions from the above link.
Also suggest re-creating a new thread on Outlook Forum to double confirm this issue.
For your convenience:
http://social.technet.microsoft.com/Forums/office/en-us/home?forum=outlook
Hope it is helpful
Thanks
Mavis
Mavis Huang
TechNet Community Support

Printing over FritzBox ist not possible with osx 10.8.5

I can not print with Networkprinter on Fritz Box with osx 10.8.5.
Is there any solution on this issue?
I'm using a Canon Pixma MP780.

It doesn't look like - from viewing this -> http://support.apple.com/kb/HT3669#canon-inkjet - list that the MP780 is still supported by Apple. I would suggest that you contact Canon support and see if they've a driver or 'fix' for this apparent incompatibility issue.
Good luck,
Clinton

Creation of new task list in CharM not possible

Hello!
I am using SOLMAN 4.0 (SP13 with the newest SP) and the problem to create the task list in Tcode: SOLAR_PROJECT_ADMIN --> System Landscape --> Change requests --"Create task list".
The following error occurs:
The project is not released. Hence cycle can not be created.
/TMWFLOW/CONFIG_UI017
How to solve this problem?
Any helpful information will be appreciated.
Thank you very much!
regards
Thom

Hi!
Yes, the problem was wrong configuration of systems.
Please try the following:
- your systems in system landscape have the right roles
- your TMS configuration is mandant dependent
- you have delivery as well consolidation routes
You can also run the check for the consistency...
You can write back, if the problem still exist...
regards
Thom

Adding a new mailbox in MAC Mail not working

Please assist me on how to troubleshoot this issue I'm having on my mac mail.
I added a mailbox by clicking the primary email inbox then after that I checked the newly added mailbox but no emails are coming in. I tested to send an email to that mailbox but still no emails are arriving.

Hello cliffcrusher,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
OS X Mail: Troubleshooting sending and receiving email messages
http://support.apple.com/kb/ts3276
Best of luck,
Mario

Login Gmail on Mail not possible

I loaded Mountain but since that I cannot log my Gmail account
Mail is refusing my password
Thierry

I have gmail set up in mail
http://support.google.com/?hl=en click on support for gmail

New Snow Leopard install, Mail not working

I installed Snow Leopard in my late 2006 iMac yesterday. It has gone through all of its updates now. When I try to open Mail it gives me the error message, "You can't use this version of the application Mail.app with this version of Mac OS X. You have Mail.app 3.6."
I would have thought that the install would have installed the appropriate version of Mail, but something's up. Suggestions?
Details:
Model Name:          iMac
Model Identifier:          iMac5,1
Processor Name:          Intel Core 2 Duo
Processor Speed:          2.16 GHz
Number Of Processors:          1
Total Number Of Cores:          2
L2 Cache:          4 MB
Memory:          3 GB
Bus Speed:          667 MHz
Boot ROM Version:          IM51.0090.B09
SMC Version (system):          1.9f4
Serial Number (system):          W87042M5VUV
Hardware UUID:          00000000-0000-1000-8000-0017F2CC2056

answer found in How do I update my mail now that I have Snow leopard

New printer, same ePrint mail, not possible

Similar Messages

Maybe you are looking for