Nexus 3548 couldn`t enable vPC feature

Hello All,
I have to implement to 2 Nexus 3548 switches for a customer. The customer like to use it as core-switch (small LAN) and also like to run VPC feature. Now I have tried to active it, but I got the follow error message:
Enter configuration commands, one per line.  End with CNTL/Z.
chefan-swi01(config)# feature vpc
Error: vPC feature is not supported
Is their a way to get VPC working on these plattform?
Software
  BIOS:      version 1.9.0
  loader:    version N/A
  kickstart: version 5.0(3)A1(1)
  system:    version 5.0(3)A1(1)
  power-seq: Module 1: version v2.1
  BIOS compile time:       10/13/2012
  kickstart image file is: bootflash:/n3500-uk9-kickstart.5.0.3.A1.1.bin
  kickstart compile time:  11/2/2012 1:00:00 [11/02/2012 09:53:29]
  system image file is:    bootflash:/n3500-uk9.5.0.3.A1.1.bin
  system compile time:     11/2/2012 1:00:00 [11/02/2012 10:27:12]
Hardware
  cisco Nexus 3548 Chassis ("48x10GE Supervisor")
  Intel(R) Pentium(R) CPU  @ 1 with 4140896 kB of memory.
  Processor Board ID FOC17480ZHN
  Device name: chefan-swi01
  bootflash:    2007040 kB
Thx a lot for any suggestions.
Kind Regards, Ferdi

Seems to be an error on the Nexus 3k product page.  We had a customer who purchased these for VPC support.
http://www.cisco.com/en/US/products/ps11541/index.html
Nexus 3500 Features
Ultra-Low Latency
Line-rate layer 2 and 3 switching at ultra-low latencies
Ideal for high-performance trading workloads
Mission-Critical Features
Network Address Translation (NAT)
Virtual Port Channel
IEEE-1588 PTP

Similar Messages

  • Nexus 3524 support vpc feature?

    Hi, I read that the Nexus 3524 does not support VPC feature, somebody can confirm me this, 
    Thanks you in advanced.

    The Nexus 3524 does have vPC support.  You have to enable it; it is not enabled by default. 
    (config)#feature vpc

  • Unable to enable sflow feature on Nexus 3548

    When I try to enable sflow via "feature sflow" command on the nexus 3548 switches running 6.0(2)A1(1C) I receive:
    Error: while enabling/disabling service: sflow, err: service not found (0x401e0005)
    Any input would be greatly appreciated.
    Thank you

    Ryan,
    Thanks for the reply... it appears to be supported on the 3000, but not the 3524, which, in my opinion is fairly stupid... I know, I know, "its an architecture thing!", but really, Cisco, you couldn't have considered that customers would want this type of visibility in this switch?? Really?!?!
    Anyway, thanks for the info... have you found a work-around or similar product that provides you similar visibility?

  • Question about Nexus 3548 vPC setup

    Hi.
    We have just installed our two first Nexus 3548 switches in our Catalyst environment. We want to set up a vPC domain between the Nexuses, to use for connections to storage and other equipment.
    I have read the guide at http://www.cisco.com/c/en/us/products/collateral/switches/nexus-3000-series-switches/white_paper_c11-685753.html and tried setting it up. I created a vPC domain on both switches like this:
    nexus1:
    vpc domain 1
      role priority 2000
      system-priority 4000
      peer-keepalive destination 192.168.105.40 source 192.168.105.39 vrf default
    nexus2:
    vpc domain 1
      system-priority 4000
      peer-keepalive destination 192.168.105.39 source 192.168.105.40 vrf default
    The switches are connected with a port-channel consisting of 2x 10GE. The IP addresses above are the ones we use for managing the switches. When I configure the port-channel as "vpc peer-link", the vpc status looks OK:
    vPC domain id                     : 1
    Peer status                       : peer adjacency formed ok
    vPC keep-alive status             : peer is alive
    Configuration consistency status  : success
    Per-vlan consistency status       : success
    Type-2 consistency status         : success
    vPC role                          : primary
    Number of vPCs configured         : 0
    Peer Gateway                      : Disabled
    Dual-active excluded VLANs        : -
    Graceful Consistency Check        : Enabled
    Auto-recovery status              : Disabled
    vPC Peer-link status
    id   Port   Status Active vlans
    1    Po2    up     1,6,100,102,106
    The problem I have is that I lose connection to nexus2 when I bring up the vPC. I can no longer access it on its IP (192.168.105.40). I cannot ping it from nexus1 either. The Nexus switches are connected to our core switches, which are Catalyst 6509. nexus1 is connected to coreswitch1 using a portchannel of 2xGE and nexus2 is connected to coreswitch2 the same way. A spanning-tree cost has been set on the uplink from nexus2, to make spanning tree block that uplink, and allow traffic between the nexuses to go over the 2x 10GE portchannel instead of over the core switches. I have attached a drawing of this.
    Maybe I shouldn't use the management IP:s for peer keepalive? Does the peer keepalive need to be on a different physical link than the peer-link?
    Regards,
    Johan

    We are not using the management ports for management, but an ordinary Vlan Interface in the default vrf, as seen below. We can of course change that and instead use the mgmt0 port if that is the best approach.
    vrf context management
    vlan configuration 1,100
    vlan 1
    vlan 100
      name DMMgmtPriv
    vpc domain 1
      role priority 2000
      system-priority 4000
      peer-keepalive destination 192.168.105.40 source 192.168.105.39 vrf default
    interface Vlan1
    interface Vlan100
      no shutdown
      no ip redirects
      ip address 192.168.105.39/23

  • NEXUS 3548 with 24 Port License

    Ive a 3548 box with 24port Lic,My concern is about the functionality of the remaining 24 Ports.Will there be a problem with the rest of the 24 ports while in production.
    NX3548# sh inventory
    NAME: "Chassis", DESCR: "Nexus 3548 Chassis"
    PID: N3K-C3548P-10G    , VID: V02 , SN: XXXXXXXXXX
    NAME: "Module 1", DESCR: "48x10GE Supervisor"
    PID: N3K-C3548P-10G    , VID: V02 , SN: XXXXXXXXXX
    NX3548# SH LICense usage
    Feature                      Ins  Lic   Status Expiry Date Comments
                                     Count
    24P_LIC_PKG                   Yes   -   Unused Never       -
    24P_UPG_PKG                   No    -   Unused             -
    LAN_BASE_SERVICES_PKG         Yes   -   Unused Never       -
    ALGO_BOOST_SERVICES_PKG       No    -   Unused             -
    LAN1K9_ENT_SERVICES_PKG       No    -   Unused             -
    LAN_ENTERPRISE_SERVICES_PKG   No    -   Unused             -

    Hello Dhanesh,
    thanks for your reply.
    We have 2 3548 licensed exactly as your Nexus.
    After a reboot of the two Nexus the first 4 ports (of the two) had problems (no input packets, only ouput packets, so unusable). There was connected devices with GLC-T, so they worked at 1 G, not 10G.
    We opened a TAC Case about this and, after remote session and many analysis, the engineer decided to replace the two devices.
    Despite this I have still some doubt.
    I found the discussion below and I post some logs of one of the Nexus, we use the 10 G not in a contiguous way.
    Thanks and regards
    https://supportforums.cisco.com/discussion/12073821/nexus-3548-24-port-license-what-ports-use
    371) Event:E_DEBUG, length:55, at 552701 usecs after Sat Mar 14 20:02:11 2015
        [825307441] Couldn't send grace period data: No route to host
    372) Event:E_DEBUG, length:58, at 255834 usecs after Sat Mar 14 19:02:57 2015
        [825307441] Couldn't fetch grace enabled status: no such pss key
    373) Event:E_DEBUG, length:55, at 819209 usecs after Sat Mar 14 19:02:18 2015
        [825307441] Couldn't send grace period data: No route to host
    374) Event:E_DEBUG, length:44, at 818664 usecs after Sat Mar 14 19:02:18 2015
        [825307441] Failed to get VDC map: no such pss key
    375) Event:E_DEBUG, length:44, at 818270 usecs after Sat Mar 14 19:02:18 2015
        [825307441] Transient read error in glob_refresh()
    376) Event:E_DEBUG, length:60, at 813122 usecs after Sat Mar 14 19:02:18 2015
        [825307441] Expiry date for feature LAN_BASE_SERVICES_PKG: 3650000
    377) Event:E_DEBUG, length:50, at 773120 usecs after Sat Mar 14 19:02:18 2015
        [825307441] Expiry date for feature 24P_LIC_PKG: 3650000
    378) Event:E_DEBUG, length:30, at 716563 usecs after Sat Mar 14 19:02:08 2015
        [825307441] checking confcheck config
    N3K-DC-1# sh int status
    Port          Name               Status    Vlan      Duplex  Speed   Type
    Eth1/1        *** FREE ***       sfpAbsent 1         full    1000    --
    Eth1/2        *** FREE ***       sfpAbsent 1         full    1000    --
    Eth1/3        *** FREE ***       sfpAbsent 1         full    1000    --
    Eth1/4        *** FREE ***       sfpAbsent 1         full    1000    --
    Eth1/5        UCS_UPLINK_FABRIC_ connected trunk     full    10G     SFP-H10GB-CU5M
    Eth1/6        UCS_UPLINK_FABRIC_ connected trunk     full    10G     SFP-H10GB-CU5M
    Eth1/7        --                 sfpAbsent 1         full    10G     --
    Eth1/8        --                 sfpAbsent 1         full    10G     --
    Eth1/9        --                 sfpAbsent 1         full    10G     --
    Eth1/10       --                 sfpAbsent 1         full    10G     --
    Eth1/11       --                 connected trunk     full    1000    1000base-T
    Eth1/12       --                 connected trunk     full    1000    1000base-T
    Eth1/13       --                 sfpAbsent 1         full    10G     --
    Eth1/14       --                 sfpAbsent 1         full    10G     --
    Eth1/15       --                 sfpAbsent 1         full    10G     --
    Eth1/16       --                 sfpAbsent 1         full    10G     --
    Eth1/17       --                 sfpAbsent 1         full    10G     --
    Eth1/18       --                 sfpAbsent 1         full    10G     --
    Eth1/19       --                 sfpAbsent 1         full    10G     --
    Eth1/20       --                 sfpAbsent 1         full    10G     --
    Eth1/21       --                 sfpAbsent 1         full    10G     --
    Eth1/22       --                 sfpAbsent 1         full    10G     --
    Eth1/23       --                 sfpAbsent 1         full    10G     --
    Eth1/24       --                 sfpAbsent 1         full    10G     --
    Eth1/25       --                 sfpAbsent 1         full    10G     --
    Eth1/26       --                 sfpAbsent 1         full    10G     --
    Eth1/27       --                 sfpAbsent 1         full    10G     --
    Eth1/28       --                 sfpAbsent 1         full    10G     --
    Eth1/29       --                 sfpAbsent 1         full    10G     --
    Eth1/30       --                 sfpAbsent 1         full    10G     --
    Eth1/31       *** FREE ***       notconnec 1         full    1000    1000base-T
    Eth1/32       --                 sfpInvali 1         full    10G     1000base-T
    Eth1/33       --                 sfpAbsent 1         full    10G     --
    Eth1/34       --                 sfpAbsent 1         full    10G     --
    Eth1/35       --                 sfpAbsent 1         full    10G     --
    Eth1/36       --                 sfpAbsent 1         full    10G     --
    Eth1/37       --                 sfpAbsent 1         full    10G     --
    Eth1/38       --                 sfpAbsent 1         full    10G     --
    Eth1/39       --                 sfpAbsent 1         full    10G     --
    Eth1/40       --                 sfpAbsent 1         full    10G     --
    Eth1/41       --                 sfpAbsent 1         full    10G     --
    Eth1/42       --                 sfpAbsent 1         full    10G     --
    Eth1/43       --                 notconnec 1         full    10G     10Gbase-SR
    Eth1/44       --                 notconnec 1         full    10G     10Gbase-SR
    Eth1/45       C3850-CORE [Port-C connected trunk     full    10G     10Gbase-SR
    Eth1/46       C3850-CORE [Port-C connected trunk     full    10G     10Gbase-SR
    Eth1/47       vPC PeerLink [Port connected trunk     full    10G     SFP-H10GB-CU3M
    Eth1/48       vPC PeerLink [Port connected trunk     full    10G     SFP-H10GB-CU3M
    Po2           C3850-CORE         connected trunk     full    10G     --
    Po3           3750-DC            connected trunk     full    a-1000  --
    Po4           UCS_UPLINK_FABRIC_ connected trunk     full    10G     --
    Po10          vPC PeerLink       connected trunk     full    10G     --
    mgmt0         --                 connected routed    full    a-1000  --

  • Nexus 3548 6.0(2)A1(1) within Prime Infrastructure 2.0

    Hi there,
    I am trying to introduce some Nexus 3548 in my Prime Infrastructure 2.0.
    For my 3048 running 6.0(2)U1(1a), no problem, they are discovered well and showing no error in the Device Work Center.
    My 3548 are unrecognised (NXOS 6 too).
    Is this an expected bahaviour ?
    Regards,
    Fred

    Hello,
    Take a thorough look at realease notes for this version and before. This is the only way.
    If your doubt is only about VPC and FEX features, it is totally supported, just be aware that upgrade is disruptive.
    Regards.
    Richard

  • Thoughs on interconnecting Nexus 3548 and 3750 switches

    Hi,
    I have two nexus 3548 switches.
    I have created port-group 1  on both switches to group eth1/47 with eth1/48.
    I have 4 sfps, 2 per switch. to connect to a single 3750 that I want to group together as well.
    So I have gi1/0/31 going to eth1/1 on nexus1 and gi1/0/32 going to eth1/2 on nexus1
    I have gi1/0/33 goin to eth1/1 on nexus2 and gi1/0/32 goin to eth1/2 on nexus2
    When I create the port group on the 3750 do I create one group with all 4 ports or will I have to create 2, one per nexus switch?
    Thanks

    Thanks for the replies. I finally got to test the hardware and config yesterday.
    Just so I am clear. the vpc and peer to peer links are only for interconnecting the two Nexus switches. I think I got that right. sho VPC br seems to say it is up. I am using Po5
    vPC domain id : 1
    Peer status : peer adjacency formed ok
    vPC keep-alive status : peer is alive
    Configuration consistency status : success
    Per-vlan consistency status : success
    Type-2 consistency status : success
    vPC role : secondary
    Number of vPCs configured : 0
    Peer Gateway : Disabled
    Dual-active excluded VLANs : -
    Graceful Consistency Check : Enabled
    Auto-recovery status : Disabled
    vPC Peer-link status
    id Port Status Active vlans
    1 Po5 up 1
    Next do I create a port channel on Nex1 and Nex2 for the two ports that connect to the 3750 (Po6 for example) or do I add the two links to the 3750s to Po5 ? I thought I add them to Po 5 but since I am mixing 1000 and 10G ports it doesnt seem to like it.

  • Windows XP Mode - Could not enable integration features

    Hello!  Let me start off with saying that I'm not very computer savvy, so please be gentle!  :) 
    So here my problem.  I have scoured forums all morning looking for a solution and have tried many things and nothing has worked yet.  I have Windows 7 Pro.  I use the Windows VM to run in XP mode so my small business programs will
    operate correctly.  This morning VM would not open.  I click to open Windows VM, it take unusually long to attempt to open.  After 5 or so minutes error message - Could not enable integration features with details stating .  It gives me
    an option to retry or continue.  When I hit retry, it does so but the ending result is the same error message.  When I click continue it states the operation has failed - the VM is not running. 
    What I HAVE tried-
    -Reboot
    -Clicked start>windows virtual pc>open windows virtual pc>right click settings
              - From this point I have tried to shut down from the close option as well as uncheck enable integration features at start up. Status is in Hibernation and has not changed. 
    Your help will be greatly appreciated.  Thank You 

    Bob, I have read as much as I can find on this problem (Enabling Integration Features and having it remain enabled), and your responses are the most straight forward, complete and seem to have helped a number of others. So, I'm adding to this discussion,
    instead of starting a new discussion, so that I can get YOUR response.  
    I am running Windows 7 Professional on a Dell Precision M6500 laptop with an Intel Core i7 processor and 8 Gb of memory.  When I first setup the laptop I installed Windows Virtual PC and XP Mode, after downloading from the Microsoft.com
    website.  While the installation went without an error, getting to use it was a major, and long problem.  I have one (very) old planner software app that I've been using since the mid 1980s. Being somewhat stubborn, I refused to change to a newer
    app. So, I installed the app under XP Mode (it doesn't run under Windows 7) and it worked fine.  I then tried to setup the printer and the Guest PCs drives (some USB).  I followed the Microsoft instructions and suggestions I found in forums. 
    I finally gave up and called and paid for Microsoft tech support.  Many weeks and we finally got it working - was able to print to my wireless printer from XP Mode and was able to backup my data to the Host PCs USB drives (I make three copies of the data
    on a daily basis, so I actually have 21 copies of the data after a week).  When we got it working I never had a problem with Enabling Integration Features, before it would disable Integration Features after I enabled them, repeatedly.  Then a Windows
    7 upgrade hung - 8 hours and the PC hadn't shut down.  I powered off the PC and then powered back up.  I got a blue screen error about CPU being too hot and the PC shut down. It was no hotter than usual. Powered up again and all seemed fine, until
    I went to start XP Mode and my planner.  XP Mode was trashed, wouldn't start.  Tried to reinstall and still had the same problem.  So, another call to Microsoft Tech support and another fee. Interestingly, the fellow that I worked with this
    time as a level higher and knew the first tech I worked with.  A few days and XP Mode was back running and the environment was actually as it had been when the PC crashed (the VHD file was still there and had my original environment - settings, programs,
    printer and drive mappings - all in place, this file is in the same location as the VSV file).
    Long winded background to my current, repeated problem. Integration Features will no longer stay enabled.  While I don't recall a "crash" or "hung" PC, my notes are all in that planner app in XP Mode and I can't get to it.  So,
    I uninstalled VPC and XPM and reinstalled from scratch. Reinstalled my planner app, configured and tested my printer and host drives (didn't map them, just access them from My Computer).  Suddenly (as I said, I can't recall anything going wrong to trigger
    the repeat of this problem) Integration Features will not enable.  I've deleted the VSV file and the problem still exists. Just "Shutdown" XP Mode and 50 Windows XP updates were installed.  Then installed 48 updates. It worked for one afternoon and
    evening. Booting the laptop this morning and Integration Features again is unstable. One more Windows update was installed.  Then I followed your suggested steps:
    Delete the" Windows XP Mode.vsv" file in the folder
    C:\users\[your user name]\appdata\microsoft\Windows Virtual PC\Virtual Machines.
    That should then allow XP Mode to start correctly.
    Have you uninstalled, rebooted XP, and reinstalled the Integration Components?  All of this occurs in XP Mode not on Win7.
    1. Uninstall the Integration Components in XP Mode from Add/remove programs
    2. Reboot XP Mode
    3. Reinstall the Integration Components in XP Mode from WVPC menu.
    The laptop is also in the same Workgroup as the Host PC and all the other PCs on my LAN.
    Any suggestions?
    Where can I find the following folders from XP Mode on the Host PC:
    C:\Documents and Settings\All users\Documents
    C:\Documents and Settings\XPMUser\My Documents
    I created folders in both with the backed up data and programs from my planner app and would like to have access to them from the Host PC.
    I'm just about at the point of abandoning XP Mode and looking for an alternative Virtual Machine app, just using Outlook, or getting the Outlook app from the original software provider of my planner app.  All of these options are less
    than ideal, but Microsoft's XP Mode has also become less than ideal.
    TIA
    Neil Cook

  • Nexus 3548 reload after Jumbo Frames

    I have a Nexus 3548... I know the Catalyst switches require a reload after enabling jumbo frames but does a Nexus require a reload?
    Also, is there a way to verify other then doing a int counter detail command?
    Thanks in advance.
    RS

    As for the verify, If I run "sh queuing int eth1/6" as per instructions I get Ambiguous command pointing to the "n" in "int"

  • Nexus 3548 ACL Logging

    "show ip access-list", IOS displays matches against each statement within the ACL and you can see counters incrementing or not, useful in troubleshooting. Nexus 3548 does not display any counters with the same command!
    I must be missing something because I cannot find a logging command that will simply add hits with command "show IP access-list <name>" (Nexus 3548)
    Is there an alternative?

    After reading Cisco ACL docs I managed to configure and get ACL logging working fine on my lab 3548:
    test# sh log ip access-list cache
    Source IP        Destination IP     S-Port  D-Port    Interface   Protocol          Hits
    10.170.x.x    10.x.x.x        0       0         mgmt0      (6)TCP            98
    Software
      BIOS:      version 1.9.0
      loader:    version N/A
      kickstart: version 6.0(2)A4(3)
      system:    version 6.0(2)A4(3)
      Power Sequencer Firmware:
                 Module 1: version v2.1
      BIOS compile time:       10/13/2012
      kickstart image file is: bootflash:///n3500-uk9-kickstart.6.0.2.A4.3.bin
      kickstart compile time:  11/21/2014 9:00:00 [11/21/2014 19:29:20]
      system image file is:    bootflash:///n3500-uk9.6.0.2.A4.3.bin
      system compile time:     11/21/2014 9:00:00 [11/21/2014 21:09:06]
    Hardware
      cisco Nexus 3548 Chassis ("48x10GE Supervisor")
      Intel(R) Pentium(R) CPU  @ 1.50GHz
     with 3805876 kB of memory.
    However in my other live Nexus 3548 "show log ip access-list cache" is not available from the command line with the following software version:
    -n35# show log ip access-list cache
                               ^
    % Invalid command at '^' marker.
    Software
      BIOS:      version 1.9.0
      loader:    version N/A
      kickstart: version 6.0(2)A1(1b)
      system:    version 6.0(2)A1(1b)
      Power Sequencer Firmware:
                 Module 1: version v2.1
      BIOS compile time:       10/13/2012
      kickstart image file is: bootflash:///n3500-uk9-kickstart.6.0.2.A1.1b.bin
      kickstart compile time:  9/5/2013 14:00:00 [09/05/2013 23:37:16]
      system image file is:    bootflash:///n3500-uk9.6.0.2.A1.1b.bin
      system compile time:     9/5/2013 14:00:00 [09/06/2013 03:25:01]
    Hardware
      cisco Nexus 3548 Chassis ("48x10GE Supervisor")
    I've researched the command line reference and found nothing to suggest version 6.0(2)A1(1b) this OAL feature is not supported......anyways  the live 3548 I can see statistics per-entry command under each ACL (these ACL's are not bound to any VLAN interfaces). show ip access-list shows no hits against any of the ACL's
    My 1st question why is the OAL ACL cache is not supported on my live version?
    2nd q - Why there are no hits when the statistics per-entry command is configured under each ACL when I know there are thousands of hits per minute?
    NB: The ip access-group in statements are applied to the Interface port number NOT interface VLAN
    example
    interface Ethernet1/6
      description ** hello **
      ip access-group test in
      switchport access vlan 885
      speed 1000
      no negotiate auto

  • In Adobe Bridge when I try to open my camera raws, I get a pop up box stating "Bridges parent application is not active.  Bridge requires that a qualifying product has been launched at least once to enable this feature"  What do I do? Please advise

    In Adobe Bridge, when I try to open my camera raws, I get a pop up stating"Bridges parent application is not active.  Bridge requires that a qualifying product has been launced at least once to enable this feature."  What the heck?  I have a PC and haven't had problems before.. I have adobe cloud and pay my monthly bill...

    Have you opened Photoshop or any other Adobe app that Bridge works with?  You need to do this if you've upgraded PS or just signed up for CC.

  • Acrobat Pro 8 and Reader X - Enable Extended Features for Form

    Using Acrobat Pro 8.3.0, I "Enabled Usage Rights for Adobe Reader" for a fillable form created in LiveCycle Designer 8.0.  The following error message occurs when opening this form in Reader X:
    "This document enabled extended features in Adobe Reader.  The document has been changed since it was created and use of extended features is no longer available.  Please contact the author for the original version of this document."
    The form has not been changed and as mentioned, I am the author.  Any solutions to allow user in Reader X to fill-in form?  Do I need to upgrade to Acrobat Pro X?

    I am having same problem with a 2011 year tax PDF fill in form I JUST got from IRS website.  The actual form is the 2011 8829.
    I can not open the PDF from the web browser or if I save it to my local drive. 
    I have not been able to open it at all ... thus I have made NO changes.
    I am running Windows 7 64 bit, Adobe Reader X version 10.1.4.
    After trying to open the doc (nothing displays) I go to properties, and it says ...
    Title: 2011 Form 8829
    Author: SE:W:CAR:MP
    Created: 12/23/2008
    PDF Producer: Adobe LiveCycle DSesigner ES 8.2.
    PDF Version: 1.7 (Acrobat 8.x)
    Tagged PDF: No
    Fast Web View: No
    What do I do to resolve this ... I only have this version of Reader ... nothing else.

  • Bridge will not now let me use camera raw, though I had been using it every day.  It says that "the parent application is not active.  Bridge requires that a qualifiying product has  been launched at least once to enable this feature."  What am I to do?

    Bridge will not now let me use camera raw, though I have been using it every day.  It ways that "the parent application is not active.  Bridge requires that a qualifiying product has  been launched at least once to enable this feature."  What am I to do?

    Usually this points to having some kind of earlier trial version still installed on your system. However without more details you are not likely to find an answer. Try this for a start:
    How To Get Help Quickly

  • Camera Raw editing requires that a qualifying product has been launched at least once to enable this feature - Can someone help me I'm on a Macbook Pro 2013 with CS6?

    I get this error message when I try to use Camera Raw in Bridge - all my other adobe products work fine. "Camera Raw editing requires that a qualifying product has been launched at least once to enable this feature"  I have a 2013 Macbook Pro - I have also updated all the know adobe updates online.

    Just a clarification in general:
    BOILERPLATE TEXT extracted from the FAQ:
    https://forums.adobe.com/thread/375816?tstart=0
    Do not be abusive or aggressive in your tone
    An aggressive, demanding, accusatory or abusive sounding post will often evoke an aggressive or abusive and unhelpful reply.
    Remember, you are not addressing Adobe here in the user forums.  You are requesting help from volunteers users just like you who give their time free of charge. No one has any obligation to answer your questions.

  • When I highlight photo's in bridge and then click open in camera raw this message comes up... Camera Raw Editing Is not enabled...Camera raw editing requires that a qualifying product has been launched at least once to enable this feature. I have used cam

    When I highlight photo's in bridge and then click open in camera raw this message comes up... Camera Raw Editing Is not enabled...Camera raw editing requires that a qualifying product has been launched at least once to enable this feature. I have used camera raw a different way but it won't seem to work with bridge.

    Have you opened Photoshop or any other Adobe app that Bridge works with?  You need to do this if you've upgraded PS or just signed up for CC.

Maybe you are looking for