NK6680, often get into standby problem

example..
when i am talking with my friend, suddenly the screen fading till completely off mode...then itself try to start and come back to origin. but in between phone disconected. same thing happens for long time. At last it work fine.
but its happen so many times..dont know its virus..or some default Nk problem or something else..
If you have similar issue and you fixed it properly or any suggestion (welcome) contact me.
Thanks.Message Edited by cen15 on 14-Apr-200707:52 AM
EDIT: removed personal email address, please use PM systemMessage Edited by damocles on 16-Apr-2007 12:41 PM

Did y install something that it started the peculiar behavior itself?
Try hard resettin it.

Similar Messages

Hard drive wakes up immediately after being put into standby

I have an IDE disk which, till now, I used to keep in standby mode (it makes an audible humming noise when it's working which annoys me a lot :<). Today I noticed that after running `hdparm -y' on it, it would spin down but then it would immediately spin up again. I'm certain that the disk isn't being used and doesn't have any partitions mounted anywhere on the filesystem. Still, I'm unable to pinpoint the reason it's waking up.
Any ideas on why this is happening?
Edit: It appears that the disk gets into standby by itself after 10 minutes. I wish I knew where this value is coming from. O.o
Edit2: Those 10 minutes must be coming from `hdparm -S1 /dev/sdb'; maybe the hard drive has a lower limit in regard to this setting. :3
(I'm not sure what kind of information would be useful in order to troubleshoot this issue, but below are some bits I believe are relevant)
Failed attempt to put the drive into standby:
[root@foutboxd ~]# hdparm -y /dev/sdb; hdparm -C /dev/sdb; sleep 1; hdparm -C /dev/sdb
/dev/sdb:
issuing standby command
/dev/sdb:
drive state is: standby
/dev/sdb:
drive state is: active/idle
hdparm -I:
[root@foutboxd ~]# hdparm -I /dev/sdb
/dev/sdb:
ATA device, with non-removable media
Model Number: WDC WD2500SB-01KBC0
Serial Number: WD-WCAL77403899
Firmware Revision: 08.02D08
Standards:
Supported: 6 5 4
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
CHS current addressable sectors: 16514064
LBA user addressable sectors: 268435455
LBA48 user addressable sectors: 488397168
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 238475 MBytes
device size with M = 1000*1000: 250059 MBytes (250 GB)
cache/buffer size = 8192 KBytes (type=DualPortCache)
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 16
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
Power-Up In Standby feature set
* SET_FEATURES required to spinup after power up
SET_MAX security extension
* Automatic Acoustic Management feature set
* 48-bit Address feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* FLUSH_CACHE_EXT
* SMART error logging
* SMART self-test
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct
smartctl --all:
[root@foutboxd ~]# smartctl --all /dev/sdb
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar RE EIDE family
Device Model: WDC WD2500SB-01KBC0
Serial Number: WD-WCAL77403899
Firmware Version: 08.02D08
User Capacity: 250,059,350,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Mar 11 21:47:50 2009 EET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (6951) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 88) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0007 236 124 021 Pre-fail Always - 708
4 Start_Stop_Count 0x0032 098 098 040 Old_age Always - 2680
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 081 081 000 Old_age Always - 14289
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0013 100 100 051 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 2365
194 Temperature_Celsius 0x0022 123 092 000 Old_age Always - 27
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0012 200 200 000 Old_age Always - 0
199 UDMA_CRC_Error_Count 0x000a 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay
Last edited by foutrelis (2009-03-12 10:18:25)

Here is what i get when i try that command.:
$ sudo hdparm -B 254 /dev/sdc
/dev/sdc:
setting Advanced Power Management level to 0xfe (254)
HDIO_DRIVE_CMD failed: Input/output error
APM_level = not supported
I tried other values also and its always the same error.
I just did another try with -y and the drive stayed in standby during ±40 minutes this time. The most annoying part is that is something that was not happening before I am pretty sure that it would stay in standby for days.
I also included my results for hdparm -I.:
$ sudo hdparm -I /dev/sdc
/dev/sdc:
ATA device, with non-removable media
Model Number: WDC WD800JB-00JJC0
Serial Number: WD-WCAM9N730552
Firmware Revision: 05.01C05
Standards:
Supported: 6 5 4
Likely used: 8
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
CHS current addressable sectors: 16514064
LBA user addressable sectors: 156299375
Logical/Physical Sector size: 512 bytes
device size with M = 1024*1024: 76318 MBytes
device size with M = 1000*1000: 80025 MBytes (80 GB)
cache/buffer size = 8192 KBytes
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, with device specific minimum
R/W multiple sector transfer: Max = 16 Current = 1
Recommended acoustic management value: 128, current value: 254
DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 *udma5
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
* SMART feature set
Security Mode feature set
* Power Management feature set
* Write cache
* Look-ahead
* Host Protected Area feature set
* WRITE_BUFFER command
* READ_BUFFER command
* DOWNLOAD_MICROCODE
SET_MAX security extension
* Automatic Acoustic Management feature set
* Device Configuration Overlay feature set
* Mandatory FLUSH_CACHE
* SMART error logging
* SMART self-test
* SMART Command Transport (SCT) feature set
* SCT Long Sector Access (AC1)
* SCT LBA Segment Access (AC2)
* SCT Error Recovery Control (AC3)
* SCT Features Control (AC4)
* SCT Data Tables (AC5)
Security:
Master password revision code = 65534
supported
not enabled
not locked
frozen
not expired: security count
not supported: enhanced erase
HW reset results:
CBLID- above Vih
Device num = 0 determined by the jumper
Checksum: correct

Help, I am about to pull my hair out, can't get into a locked drive and Time Machine problem

I've screwed everything up, I think. I had Time Machine doing backups to an external 500Gig drive and somehow it got locked. I went into Get Info to try and change the access but it won't allow me. On top of this problem, my original drive died and I can't get into Time Machine to restore. When I click "Enter Time Machine", nothing happens. I created an eDisk and a startup disk to another external drive that I'm using now, but since everything that's been backed up is on the other drive that I can't access. When I try accessing the drive it gives: "The folder “G-DRIVE ” can’t be opened because you don’t have permission to see its contents." I'm not knowledgeable enough to work from the command line, so if I need to do that to access the drive, please walk me though it. As for the Time Machine problem, I have no idea how to recover anything since it won't even come up, it just sits there. Outside of blowing my brains out, I don't know what to do. Any help would be greatly appreciated as I can't afford to take it to Apple to let them try and fix it.

Hello, not sure how this might affect a TM drive, or not, but...
Here is what i needed to do for my drive "320GB HD", the last command is just for clean up
Open Terminal and type these commands carefully with the spaces & change 320GB HD to the name of your drive.
sudo chflags 0 "/volumes/320GB HD"
sudo chown root "/volumes/320GB HD"
sudo chmod 1775 "/volumes/320GB HD"
sudo -k
That said, these should be sufficient to do the job:
sudo chflags 0 "/Volumes/320GB HD"
sudo chmod a+rx "/Volumes/320GB HD"

Trying to get into the app store and it asks for my password. The problem is that it is showing an Apple ID I don't use ghosted in. I can't figure out how to use my correct ID.

Trying to get into the App Store to update some apss. It asks for my password but the problem is that it is showing ghosted an Apple ID I don't use. Can't figure out how to fix it.

You installed a hacked app, originally from the Mac App Store. It contains the receipt for a different app, downloaded using an account that you don't control. You need to identify and remove the hacked app.
Important: The app you need to remove is not necessarily the one named in the App Store alert. For example, if the App Store says you need to update "Twitter," the hacked app may be "Angry Birds" or something else entirely. Don't make any assumptions about which app you're looking for. To find it, you have to carry out a systematic search.
Triple-click anywhere in the line of text below on this page to select it:
kMDItemAppStoreHasReceipt=1
Copy the selected text to the Clipboard by pressing the key combination command-C.
In the Finder, press command-F to open a search window, or select
File ▹ Find
from the menu bar. In the search window, select
Search: This Mac
from the row of tokens below the toolbar. Below that is a popup menu initially showing Kind. From that menu, select Other...
A sheet will drop down. In that sheet, select Raw Query and click OK or press return.
Now there will be a text box to the right of popup menu. Click in that box and paste (command-V).
The search window will show all the App Store products you've installed. Compare those search results with the list of your purchases from the App Store. To see the complete list, you may need to unhide hidden purchases. If any apps were download from the App Store using other Apple ID accounts that you control, sign in to the store under each of those ID's and check the purchases.
At least one of the items listed in the search window is not among your purchases in the App Store. Move each such item to the Trash. You may be prompted for your administrator password. Empty the Trash.
Log out and log back in. Test.

Can't get into talk talk email account in Mozilla, you have undefined new mails in your inbox message. No problem with Internet Explorer though

I've been using the Firefox browser for nearly a year now but for the past three days I can't open my tiscali email account via Firefox. The message "you have undefined new mails in your inbox" comes up. Talk Talk technical help says there is a problem with Firefox and advised me to use Internet Explorer. I can get into my account through Explorer but would much prefer to use Firefox so please help me out.

Apparently TalkTalk mail will work with Firefox 4 and Firefox 5 ''if'' you set the browser to ''lie'' to TalkTalk mail by saying that you are still using version 3.6.
You can find the instructions for that in a post on the TalkTalk forums: [http://www.talktalk.co.uk/forums/showthread.php?t=185113#post2452787 Firefox 4 & TalkTalk webmail - Forums].
Note: when you open about:config the first time, it will display a warning message that you should be careful with the changes you make. That's definitely good to bear in mind.
Does it work?

When I plug my iPhone 4s into my PC, I get an error message that says iTunes needs a newer version of Apple Mobile Device Support. It wants me to uninstall both the AMDS and iTunes and then reinstall iTunes. Has anyone else run into this problem recently?

When I plug my iPhone 4s into my PC, I get a message that says iTunes needs a newer version of Apple Mobile Device Support. It wants me to uninstall both the AMDS and iTunes and then reinstall iTunes. iTunes won't recognize my phone and so I can't synch it. Has anyone else run into this problem recently and how did you resolve it? Thanks!

Thank you both. I suppose I should have prefaced my question with the concern that I've read a number of other posts from people who have had a similar issue and when they tried to follow the directions, they ran into a multitude of other problems. As you might imagine, I'm hoping to avoid the creation of new problems as I try to solve this one. Thanks again.

I can't get into my yahoo bookmarks. I have spent time with AT&T and the conclusion they came to is that it may be a problem with Firefox and yahoo. Help please

I am using a HP Laptop NOT mobile device. Every time I try to go into my YAHOO bookmarks it asks me to sign in which I do to no avail. AT&T came to the conclusion it may be that Firefox and Yahoo are not working together. I just downloaded both the latest versions of Firefox and the yahoo toolbar again to no avail. Is there something with Firefox that is preventing me from getting into my yahoo bookmarks??

It's really up to you how often you want to clear history. If you have a large hard drive, Firefox may save history for a year or more...

I don't want the 'chat' option. how can I disable it? I often get the message that I am being disconnected from chat because i've logged on from another computer. I never use chat, and it just seems to be a problem. How can I get rid of it?

I often get the message that I am being disconnected from chat because i've logged on from another computer. I never use chat, and it just seems to be a problem. How can I get rid of it?

Don't expect any wonders. If you use it heavily with multiple applications running at the same time, nobody can help you. It's physics: more usage => higher energy consumption.
Here you can find some tips to reduce the battery consumption. My tip: close applications if you don't need them right now and reduce screen brightness.

I tried to update the latest update 1/27/14 and it ran into a problem. I am not able to get to my library. I tried to download Itunes and it won't work . What should I do?

I tried to update the latest update 1/27/14 and it ran into a problem. I am not able to get to my library. I tried to download Itunes and it won't work . What should I do?

Are you sure it was error 0604 since I never heard of that error, it does not appear in the list of errors in the following and a search of Apple's support site gets no hits. However, error 1604 is list and users have reported that error number. If 1604 is the error number the following tell yu wnat to do when you click on that error number:
iOS: Resolving update and restore alert messages

Trying to access hotmail account but it is taking forever to get into hotmail it was working ok at start of week only yesterday and today have a problem with it

rying to access hotmail account but it is taking forever to get into hotmail it was working ok at start of week only yesterday and today have a problem with it

You can try these steps in case of issues with web pages:
You can reload web page(s) and bypass the cache to refresh possibly outdated or corrupted files.
*Hold down the Shift key and left-click the Reload button
*Press "Ctrl + F5" or press "Ctrl + Shift + R" (Windows,Linux)
*Press "Command + Shift + R" (Mac)
Clear the cache and remove cookies only from websites that cause problems.
"Clear the Cache":
*Firefox/Tools > Options > Advanced > Network > Cached Web Content: "Clear Now"
"Remove Cookies" from sites causing problems:
*Firefox/Tools > Options > Privacy > "Use custom settings for history" > Cookies: "Show Cookies"
Start Firefox in <u>[[Safe Mode|Safe Mode]]</u> to check if one of the extensions (Firefox/Tools > Add-ons > Extensions) or if hardware acceleration is causing the problem.
*Switch to the DEFAULT theme: Firefox/Tools > Add-ons > Appearance
*Do NOT click the Reset button on the Safe Mode start window
*https://support.mozilla.org/kb/Safe+Mode
*https://support.mozilla.org/kb/Troubleshooting+extensions+and+themes

Y ipod because,I keep getting an error -9808 saying I can't get into the itunes store. What can I do to resolve this problem? Thanks in avance!

Hello, I restored my ipod and now I can't restore my information back on my ipod. I read the manual on how to restore my ipod and I click the ipod under devices but, it won't let me get into the itune store. I keep getting error -9808. What can I do to resolve this problem? Thanks!

Have you seen this Apple support document?
http://support.apple.com/kb/TS2753
B-rock

Problems getting into rescue mode muvo2

i've had a problem with the sound on this player it was a little quiet for my liking so i want to install the international firmware. Problem is i cant get into rescue mode, my player is fully charged and i was wondering if that is the reason i cant access it should i run the battery down?

Battery level shouldn't affect Rescue Mode. Make sure you follow the procedure exactly for the MuVo? which is: unplug the player from your computer and remove the battery from the player. Press and hold the Menu button while inserting the battery back in the unit. Release the Menu Button. The player will display Recovery Mode in its LCD screen.

My iMac Version 10.6.8 has problems starting up. I often get a white screen without the apple icon.

My iMac Version 10.6.8 has problems starting up. I often get a white screen without the apple icon. Then I must turn the computer off and restart. Restarting will usually bring up the Apple icon and the start screen. What could be causing this? And how can I resolve this issue. My Mac is still under warranty, I've had it just 7 months.

Reset the NVRAM/PRAM and Reset the SMC.

Difficulty sending photos through iPhoto 11 often get a connection error. When I go to my email and copy the photos in email the emails go out always with never a problem

I have difficulty sending photos through iPhoto 11 often get a connection error. When I go to my email and copy the photos in email the emails go out right away and never seem to have a connection problem? Why did they cahnge the process for sending photos form iphoto?

It is an addition option some people like and other do not (I do not) -- to use it as always is trivial - in the iPhoto preferences set Apple Mail as the e-mail client
LN

My camera often gets stuck or says "camera not available" what's the problem? What should I do?

My camera is not working properly. It often gets stuck or says " camera not available" and if I take video via manual mode it gets stuck with a photo but the video is being taken. What's the problem?
Solved!
Go to Solution.

Hi soubham and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
Did you try the advice offered by SergioPL above?
What are your thoughts about this forum? Let us know by doing this short survey.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

NK6680, often get into standby problem

Similar Messages

Maybe you are looking for