'No Entry Sign' on Macbook Boot-up with new SSD

Hi Everyone,
I'm a first time poster looking for some help.
I recently installed a new SSD (Samsung 830 128GB 2.5") in my white Macbook (2,1).
After buying the SSD I did a clean install of Mac OS X Mountain Lion, however, due to not having a physical disc, I performed the install using my iMac, the Mountain Lion DMG, and the new SSD in an enclosure. The install seemed to go fine and my iMac will boot up from the SSD with no problems, but when I try to put the SSD in the Macbook, I get a 'No Entry' sign and no sign of life.
I have tried putting the SSD in an enclosure and tried to boot it with the Macbook by holding 'Option' to choose my start-up disk. When I do this, it reads both the 'Macintosh HD' and the 'Recovery HD' but when I click on either option to boot, it shows the 'No Entry' sign. Is there anyone who could suggest anything - any help would be greatly appreciated.
Mr Flollop

I have now managed to get Mountain Lion working on my Macbook - even though as Mike has correctly pointed out, it is not in the system requirements.
I believe the problem lay with installing Lion on the SSD via a different machine than the one the SSD was meant for - though this should not have been the case.
I ended up installing the SSD in the Macbook and booting Mountain Lion install from a USB stick - it worked and Mountain Lion is running well on my machine.

Similar Messages

My late 2012 mac mini boots slow with new ssd drive

So here is the situation. I purchased a 128gb ssd drive, installed it a usb enclosure, formatted it to Mac OS Extended (Journaled), cloned it with carbon copy cloner 3, used the option key during boot up and selected the ssd drive and it booted my mac mini and it functioned perfectly. I than tested it for dozens of reboots and it worked fine. I then took apart my mac mini and removed the original hard drive and installed the new ssd drive. When I boot to the ssd drive it still takes 47 to 53 seconds just like the old drive. Aren't ssd drives supposed to be a lot faster?
My solution or tip is as follows; The reason it takes so long to boot is because the mac mini doesn't know you replaced the old drive and it is looking for it during the boot process. Finally it can't find the drive so it boots to the ssd drive. All you have to do to correct this is click on "system preferences", select and click on "startup disk" and select your ssd drive and click on "restart". After these steps your mac mini will now boot in about 17 seconds. Issues solved.

Yes, my solution fixed the issue. I went from a 47 to 53 second boot time to a 17 second boot time. The ssd drive is significantly faster than the original drive that came with my late 2012 mac-mini. This is my first post and I wasn't sure how to post this as a tip. I have another tip regarding usb 3.0 hubs.

Boot Problem with new SSD Drive on CQ60-409SA

I have just replaced my HDD with a new Sandisk 120GB Extreme 11 SSD.
All went OK with no problems installing Win 7 Ultimate and much faster search time, etc..
The problem I have is that when I boot the laptop from cold, i.e switch it on for use, the SSD is not recognised and I just get a Black screen with Flashing cursor top left corner, but if I then press Control-Alt-Delete, the system Reboots, and then boots into windows no problem.
I am trying to find out if I can Access BIOS Advanced Options, if I press F10 during boot I only get Options like Change Boot order, and not more Advanced Option to change Drive parameters, etc... and F2 does not run Diagnostics for SDD.
Any help would be greatly appreciated as I am very pleased with the performance increase the SSD drive gives to Windows and Boot itme except for having to boot twice.
Best regards,
This question was solved.
View Solution.

No worries.
What year model is your notebook?
About your request for the Advanced options, unfortunately that is not possible with a BIOS supplied by HP.
You can, if you don't mind taking the risk, go to a BIOS Mod forum and look for a modified BIOS for your notebook there. The modified BIOS will have advanced options.
Have you tried the Solution and Update finder on the Support download drivers page for your notebook? It says that it will find missing drivers.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

I got a mid 2011 macbook air 13 with 128gb ssd is it possible to upgrade my storage?

i got a mid 2011 macbook air 13 with 128gb ssd is it possible to upgrade my storage?

It is entirely possible, as many have known from day one (as ifixit's first teardown revealed). Unlike the unupgradeable memory, the SSD is a discrete expansion card that is removeable with just one screw, after removing the case cover. It is however debateable as to whether such an expansion is worth the possible risk of making demonstrable changes to the MBA whilst still under warranty. So you may want to stave off consideration for a while.
I made the upgrade recently on my older 2010 MBA, and it was easier than upgrading the HDD on my old MacBook Pro.
Here OWC/Mac Sales has kits and instruction videos.

Macbook 13.3 with new battery and new magsafe adaptor will not charge above 80% no indicator light on charger display states "not charging" while attached to charger

macbook 13.3 with new battery and new magsafe adaptor will not charge above 80% no indicator light on charger, display states "not charging" while attached to charger

rgregoryadams wrote:
macbook 13.3 with new battery and new magsafe adaptor will not charge above 80% no indicator light on charger, display states "not charging" while attached to charger
You'll want to reset your SMC (System Management Controller). Instructions are simple:
http://support.apple.com/kb/ht3964

Rescue and recovery problem with new SSD

Hello all,
i am new in lenovo forum.
Recently i got a new SSD, so i installed win 7 there. Previously i had win xp in my old HDD. The thinkvantage blue button worked fine with my previous configuration (win xp+old HDD). Now, when i try to install RnR 4.3 for win 7 i got this error message "error 25014. There was an error installing the rescue and recovery boot manager. Return code: 6". Can any one suggest how to solve it and use thinvantage blue button in win 7 with new SSD.
thanks in advance
Reza

sorry i forget to mention that i an using thinkpad T400.

Driver issue FIXED in Vista / boot camp with new, unibody macbook pro!!

Hay people, I found a fix for the freezing issues with Vista running in Boot camp with the new, unibody Macbook pros. The driver for the 9600M Gt is no good if you install it from the Apple 2.1 version driver disc (Mac osx disc)for some (most) of us.
I needed to go to Nvidia's site and download the one from DECEMBER 08. If you click the "download drivers" tab on the site, scroll past the current driver it wants you to look at (go to the near bottom of page), click the archives, and input your OS version. Also input "Gforce" and "M" series when needed. It will give you a choice of two drivers. DO NOT CHOOSE THE FEB 09 Driver. Thats the BAD driver for most of us. Choose the DECEMBER 08 driver. Download and enjoy. Be sure to roll back the VGA driver (or the current driver) first before you install this. It should work.
I've been through the ringer with this for weeks now and have even tried to take my MBP back to swap for a new one. Apple wont have any of that so I thought I was SOL. Not quite. This DOES work for me with Vista. It also works for Windows & if you have it handy.
By the way, I am posting this for people who HAVE HAD THE FREEZING problems, not for people who haven't. Apparently there are some out there who are running Vista just fine on their unibody MBS's. Most of us are not.
Cheer's-----Seattle, where the evil empire looms dark

This never worked. I sold that machine and got a new 17" unibody. IT, by the way, works just fine. I KNEW it was that **** 15'. It took 30 more seconds to boot up I found out also.

Macbook boots up with a question mark

Hi,
My Macbook suddenly began to boot up with a pale greay desktop screen colour and in the centre of the screen there is a folder with a question makr inside it. I can not progress to do anything else with it..any ideas?
Cheers CFV

That folder with the question mark icon means that the MacBook can't find the boot directory. That can either mean it can't find the hard drive or the Operating System data on the hard drive is somehow corrupted.
Put your install DVD into the optical drive (CD/DVD drive) and reboot. As soon as you hear the boot chime, hold down the "c" key on your keyboard (or the Option key until the Install Disk shows up). That will force your MacBook to boot from the install DVD in the optical drive.
When it does start up, you'll see a panel asking you to choose your language. Choose your language and press the Return key on your keyboard once. It will then present you with an Installation window. Completely ignore this window and click on Utilities in the top menu and scroll down to Disk Utility and click it. When it comes up is your Hard Drive in the list on the left?
If it is then click on the Mac OS partition of your hard drive in the left hand list. Then select the First Aid Tab and run Repair Disk. The Repair Disk button won't be available until you've clicked on the Mac OS partition on your hard drive. If that repairs any problems run it again until the green OK appears and then run Repair Permissions.
If your hard drive isn’t recognized in Disk Utility then your hard drive is probably dead.

Dual Boot Selection with two SSD Installed

I have two SAMSUNG SSD's installed in the W540.
SSD #1 -- Microsoft Windows 7 Professional
SSD #2 -- Microsoft Windows 7 Ultimate
The SSD's had a complete install of each Microsoft Windows operating system without using the dual boot manager. I select teh SSD to boot from by using teh F12 key at boot time.
On my previous computer (HP EliteBook Workstation 8560w), the BIOS had a option to display a boot selection menu for me to select from without having to manually select the option to display. The boot selection menu gave me 20-30 seconds to select a alternative boot option. If I did not respond it woudl boot to the primary drive.
Can the Lenovo W540 be setup the same way? I can find no options in the latest BIOS.

I am honestly dubious that your previous HP machine had anything in the BIOS to provide this "Boot Manager" functionality you've described. Your description is exactly what Boot Manager in Windows does, which probably what was in effect on your HP machine.
Now you say you installed two separate versions of Windows on two separate drives, and without involving Windows Boot Manager. That suggests to me that you unplugged the other SSD when you did each install, so that the Windows installer didn't even know about the other bootable OS when doing its current install. If it had seen the other pre-existing bootable Windows, then the second install would have triggered the creation of a 2-OS boot menu (identical to what you say you saw on your old HP machine). You could still have two bootable Windows, on two separate drives (or, you could also have installed to two separate partitions on one drive if you wanted to), and at boot time Boot Manager would present the menu to you and you'd select one or the other. The most recent Windows to get installed would probably have made itself the "default", so that after 10-30 seconds it would auto-boot to that Windows if you didn't arrow up/down and press ENTER to select the other Windows for this particular boot.
The BIOS of the machine has a "boot sequence" setup, and one of your two SSD drives MUST be first, in front of the other. So at boot time by default (in the absence of F12 to select a boot device) the BIOS would normally go to THAT "first" drive in the boot sequence list, locate the "active" partition on that drive (where Boot Manager is assumed to live), and start the boot process. If Boot Manager sees a 1-OS boot menu, it just goes to that partition (as C, where Windows lives on that drive) and starts Windows. If a 2-OS boot menu exists, Boot Manager presents it to you and you decide which Windows you want to boot to.
When you push F12 at boot time, you simply say to the BIOS "let me pick which of my drives I want you to go to, to then find the "active" partition on that drive to kick off the boot process". Since you did two completely independent Windows installs, I would say that you probably have a "system reserved" partition (which is marked "active") on each SSD, along with a C system partition (for Windows) on each SSD. So you can actually boot to either drive, via F12, or you can just let the machine boot to whichever one you know to be first in the boot sequence list.
But... if you'd simply installed your second Windows to the second SSD while the first Windows/SSD was still cabled and visible, the second Windows install would have done everything you're now asking to be done. The existing 1-OS boot menu (on the first SSD) would have been seen and updated by the Windows installer, to add the second Windows to the menu which would thus now be a 2-OS boot menu. The second Windows would get installed wherever you wanted it to get installed (i.e. to the second SSD), and all would be well with the world.
Note that had this taken place, no second "system reserved" partition (marked "active", and housing the second copy of Boot Manager) would have been created on the second SSD with the second installed Windows. The existing "system reserved" (marked "active", and living on the first drive in the BIOS boot sequence list) would simply have had its boot menu updated from 1-OS to 2-OS, and you'd be home free right now.
This is exactly how Boot Manager works. I'm sure your old HP machine had such a setup, with your two Windows installed sequentially over time, and with the second one recognizing the first one's existence and adding itself to the boot menu to produce a 2-OS boot menu which is what you saw. That wasn't from the BIOS. It was from Windows Boot Manager handling a 2-OS boot menu.
So, what can you do now? Well, technically, you only need one "active" partition (i.e. "system reserved", where Boot Manager lives) on the first SSD in your BIOS boot sequence list. You won't need the second "system reserved" which in my opinion was probably created (unnecessarily) when you did your second Windows install with the first SSD temporarily disconnected.
But the goal here is to get the 1-OS boot menu that's on the first SSD "system reserved" partition updated, to add the second Windows on the second SSD, producing a 2-OS boot menu. And to do that you can use a wonderful 3rd-party product named EasyBCD. It is a tool to maintain your boot menu, and you can manually do things after-the-fact (like now) which you should have done before, or simply to perform maintenance or changes.
So, with both SSD's cabled and operational (your current booted Windows will appear as C, and probably your other drive's Windows partition will thus appear as D to the current booted Windows), you run EasyBCD. It really doesn't matter which Windows is on the first SSD and that is first in the BIOS boot sequence, only that it will be the boot menu in the "system reserved" partition on that drive which will be manipulated by EasyBCD to become the 2-OS menu. You can make either Windows the default (which will auto-boot in 10 seconds if you don't select the other Windows), no matter which SSD it's on.
You can view the current boot menu (from the currently booted Windows) via EDIT. You pick which entry is to be the "default".
To add a new entry to the boot menu, push the ADD button and navigate to the drive (D) the Windows to be added lives on.
If you don't already have same, I would recommend you have a "system image" backup of both of your bootable Windows drives (to an external USB 3.0 drive, ideally), so that if you're skittish about doing this you'll at least be able to quickly and easily restore what you currently have from your backups.
But believe me, EasyBCD can be trusted to do exactly what you want to do... which is to create a 2-OS boot menu on your first drive's "system reserved" partition. This 2-OS boot menu will name BOTH of your two bootable Windows, from your two SSD drives. You won't need to push F12 to select the boot device, just let the machine go to the first drive in the boot sequence and kick off Boot Manager, and the rest will behave exactly as you are now seeking.
Let me know if you have questions. And for sure, let us know how it turns out.

Macbook Pro 2012 with 240GB SSD or Macbook Air 2012 240GB SSD or Macbook Pro Retina

Macbook Pro 13inch 2012 240GB SSD Specs:
2.5GHz Dual-core Intel Core i5, Turbo Boost up to 3.1GHz
4GB 1600MHz DDR3 SDRAM — 2x2GB
500GB Serial ATA Drive @ 5400 rpm
SuperDrive 8x (DVD±R DL/DVD±RW/CD-RW)
240BG Mercury Extreme Pro 6G SSD
Intel HD Graphics 4000
Overall Price $1600+Tax
or
Macbook Air 2012 13inch with 240GB SSD SPECS:
1.8GHz Intel Dual-Core Core i5, Turbo Boost up to 2.8GHz
8GB 1600MHz DDR3L SDRAM
240GB Auro Pro 6G Solid State Drive
Turbo Boost up to 2.8GHz
Intel HD Graphics 4000
Overall Price $1600+Tax
or
Macbook Pro Retina 15inch 2012 256SSD Specs:
2.3GHz Quad-core Intel Core i7, Turbo Boost up to 3.3GHz
8GB 1600MHz DDR3L SDRAM
256GB Flash Storage
Intel HD Graphics 4000
NVIDIA GeForce GT 650M with 1GB of GDDR5 memory
Overall Price $2199+Tax
orMacbook Pro Retina 13in 2012 256SSD Specs:
2.5GHz Dual-core Intel Core i5, Turbo Boost up to 3.1GHz
128GB Flash Storage or 256 Crucial m4 256GB 2.5 inch if possible to upgrade
2.5GHz dual-core Intel Core i5
Turbo Boost up to 3.1GHz
8GB 1600MHz memory
Intel HD Graphics 4000
I'm looking for a laptop that will last me a couple of years which is why I'm upgrading to SSD without losing performance. I usually game on my Mac so I want a laptop to handle that, handle programs in the background and writing or reading without losing speed, I also need a laptop that has fast boot time.
I will be using the laptop mainly for school and running programs such as iWork and mircrosoft office as well as websurfing and video streaming thanks for any advice.

I hope others pipe in with their comments, but the first suggestion is to visit your local Apple Store and try out the units. Trying them out can make a difference in your decision.
This is how I'd try to make sense of this:
MBP 13 2012:
Solid all-purpose portable at a decent price, and even has a 240GB SSD. If you don't load it with tons to videos, this will more than fit your needs as a student and websurfer. A little heavier than the others here, but it's a solid package that's stable. Great if you need to use the CD/DVD.
MBA 13 2012:
Also good, similar specs, notably lighter. Notes are easy to take, and easier to carry on long campus treks. If you're not near a power source, the battery life may be a concern. If you need a CD/DVD, you can connect it when you need it - but it's extra. Servicing a MBA is more difficult.
MBR 15 2012:
Beautiful display, packed with performance. No DVD/CD drive, NVIDIA performance is unproven, kind of pricey, the first generation of a device; it's going to get better over time. Can't be serviced in any way by the user; the Apple Store is your only option. Now's not the best time to get the MBR.
MBR 13 2012:
Same comments.
I'd say the MBA is a good pick. Few moving parts, therefore more reliability. Low heat. You can always attach a CD/DVD drive via USB. Intel Graphics is solid; no problems there. Plenty of capacity for your needs. And the display is bright. MBA 13 or 11, IMO.

Macbook pro hard drive transfer to new i7 Mac Mini with new SSD

I've seen some of the threads on drive transfer but wanted to get more input. I currently have late 2008 Macbook Pro with 750gb hard drive running Lion latest version. I bought a new Mac Mini i7 with dual 500 gb drives. I also have new SSD 512gb. I want to use SSD as boot drive for Mac Mini and install 750gb drive as 2nd drive. I know how to remove and install the drives. What is best sequence, software and procedure to execute the exchange? Any help would be greatly appreciated in advance.

Hello,
Not clear on your circumstances, but...
Best way to get an exact bootable copy of your old drive to the new one is with Carbon Copy Cloner...
http://www.bombich.com/software/ccc.html

T410 will not boot with new SSD

I've cloned my HDD to a new SSD, but it will not boot. It goes into a Lenovo Think Bios splash screen / Black screen loop. I booted off a repair disk and performed a repair, but it is still doing the bios loop thing. This has happened with both an OCZ and a Kingston SSD. Any ideas? Thanks...
Solved!
Go to Solution.

I'm going to venture a guess that the drive was not cloned properly.
The "new" drive must be in the machine's HDD bay, and the "old" one in the USB enclosure.
I always use Clonezilla for the rare occasions that I actually clone something, but Acronis should do just fine as well.
Good luck.
Cheers,
George
In daily use: R60F, R500F, T61, T410
Collecting dust: T60
Enjoying retirement: A31p, T42p,
Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

Permissions problem with new SSD boot drive

I recently installed an OWC SSD drive as a boot drive on an iMac I've had for many years. I’m having some sort of permissioning error that I can’t figure out how to resolve.
I’ve setup the SSD as the boot drive (created user named “Boot Admin”). 10.9.3. All data and files remain on my old spinning disk
When the computer first boots, as expected, I’m presented with 2 users at the login screen (“Boot Admin”; Original User Account). If I choose my old user account, I receive the following error:
"You are unable to log in to the user account “<name of original user account>" at this time. Logging in to the account failed because an error occurred.”
If I choose the Boot Admin user I’m able to login without issue as the Boot Admin user (no access to my original apps and data). At that point, I can choose Log Out from the Apple menu and then login using my old user account. When I follow that sequence, I’m able to login with no issues. Apps are there, data is accessible etc. I can enjoy the speed of the SSD.
Although, if browse within Finder to the Boot Admin user on the hard drive, none of the folders are accessible (the little red icon is on the folders). Similarly, if I boot straight into the Boot Admin user and browse to my original User on the hard drive, none of its folders are accessible!
I am at a loss on how to troubleshoot. Ideally, I would like to login in directly to my old user account (eliminate the 2 step — login to Boot Admin, log out, login to Original User) and have full file access to things within both the Boot Admin user and my original user account.
Any guidance or tips on how to troubleshoot? thanks in advance

I appreciate the continued assistance. I'm clearly overlooking something and Google is not my friend! I've tried.
At the expense of repeating myself, I'll share my current configuration:
10.9.3
2 hard drives (new SSD with name "Boot Drive" and original spinning disk "Macintosh HD")
Startup Disk in System Preferences is "Boot Drive"
"Macintosh HD" has 3 User Folders: bootadmin, jayelevy, shared
jayelevy is my home folder - all my documents are in tact
bootadmin has the normal home folder structure
"Boot Drive" has 3 User Folders: bootadmin, jayelevy, shared
jayelevy is empty; no folders
bootadmin has the normal home folder structure (Desktop, Documents, Downloads, Movies, etc), but each is empty with the exception of Movies and Pictures. I've moved my Aperture databases to these 2 folders to take advantage of the speed of the SSD
When I restart the iMac I'm presented with 2 user choices: jayelevy and bootadmin
If I initially select jayelevy, I receive the error mentioned at the start of the thread
If I initially select bootadmin, I can login without issue, but get the standard Mac desktop (not my home).
If I then log out of bootadmin (not restart, but logout) and then choose jayelevy, the signin completes successfully and my desktop/home folder is restored to it's normal and expected condition.
I am still trying to avoid this step of login/logout/login.
I imagine I'm overlooking the obvious, but I'm in uncharted grounds for me! Here I thought the hardware swap to replace my optical drive with SSD would be the hard part. That was simple! I've stumbled on the software side!

Exchanging macbook air 13 with new haswell macbook pro.

I recently bought a haswell series 13" macbook air exactly 1 week before the introduction of the new haswell macbook pros. After considering the spec and price difference I realized I'd rather have the pro. I looked on the returns tab on the website. It said I can return my product within 14 days. Is it possible for me to exchange my air for the pro without having to go through returning my macbook air and buying the pro? I realized the price difference wasn't all that differernt and I wouldn't mind the extra power. I currently have the 13" macbook air i5 with 8gb. I plan on getting the 8gb for the 13" retina display macbook pro as well.

I still have 1 day to return it. Currently my best option is to return my air for a full refund and then apply that towards the pro. However there is a delay on the returned funds.
The credit card I bought the MBA on only has enough credit for one of the macbooks at a time. However I need to purchase it on that credit card because it offers me product insurance.
So as of now I have to wait 3-5 days for the credit return and then order the pro which will take an additional week. I'm just trying to find a way to reduce the time between retuning my air to getting the pro. lol.
Thank you!

Cannot boot with new SSD

Installed new OWC 240G SSD in 2007 iMac. Started up with old HD in external case running OS 10.10.2. Initialized SSD with Disk Utilities, and it mounted on the desktop. Transferred contents from old HD to new SSD. Computer boots fine from old HD in external case, but does not boot with internal SSD. After displaying Apple symbol for a few seconds of the startup process, computer goes to a kernel panic and gets into a loop of retry message-Apple symbol-message-etc. The SSD shows on the desktop, but does not show as a startup disk in System Preferences pane. Disk Utilities shows drive is fine, but repair of permissions is grayed out. Window says permissions repair is only permitted on OS installed with an Apple installer. System folder on the SSD does not show the "blessed" symbol. Have tried recloning using Time Machine backup - same result. Installed eDrive on SSD with TechToolsPro, and can start up in eDrive thru TTP window, thus verifying all cabling. After booting with original internal HD installed in external case, SSD will show on desktop, but will disappear in a few minutes after a message says it was improperly ejected. Suggestions? Is there a way to access OS 10 software purchased and downloaded from Apple site?

Many possibilities here. Maybe a bad connection when you installed the drive. Maybe a bad drive. Maybe a bad SATA cable.
How did you format the drive? Should be Mac OS Extended Journaled. When you boot into the recovery drive, access disk utility from there and see if you can access the drive.
I have the same drive as you. What I did is use Disk Utility from the recovery drive of TM. I first re-formatted the SSD drive. Then I used Disk Utility to restore the whole drive of my original to the new SSD drive.
You can still download the Yosemite installer from the App Store in your purchases providing you downloaded it from the App Store already.

'No Entry Sign' on Macbook Boot-up with new SSD

Similar Messages

Maybe you are looking for