No Internet Access on Private Network
Hi,
I have an and ESXi Host with few VM's and i require Internet Access on these servers. This is Mini lab i have created at home.
I have My Home Broadband Router (192.168.0.1) acting as a DHCP server handing out DHCP addresses as usual.
A Cisco 3750 with 3 Vlans created with inter vlan working with the "Ip Routing" command.
A Physical PC
A ESXi Host
3 Vlans:
Vlan 100 10.0.9.1/24 (Home Vlan) Created DHCP Pool on this Vlan on 3750
Vlan 200 10.0.10.1/24 (Voice Vlan) Created DHCP Pool on this Vlan on 3750
Vlan 300 192.168.0.2/24 (Internet Vlan) DHCP handing out IP's from home broadband router (Uplink setup from Home ADSL router)
3750 Switch:
Port 1 ESXi Trunk
Port 2 Home PC (Vlan 100)
Port 3 – 28 Vlan 300 and all giving DHCP addresses from home ADSL router
Home PC (Vlan 100 – IP Address 10.0.9.52)
From Command Prompt PC can ping the following:
10.0.9.1 (Gateway) Ping Ok!!!!!
10.0.9.2 (ESX Host) Ping Ok!!!!!
10.0.10.1 (Gateway for Voice Vlan 200) Ping Ok!!!!!
192.168.0.2 (Gateway for Internet Vlan 300) Ping Ok!!!!!
192.168.0.1 (Home Router & DNS) No Ping…..
Cisco 3750 Switch
This can ping the following:
10.0.9.1 (Gateway) Ping Ok!!!!!
10.0.9.2 (ESX Host) Ping Ok!!!!!
10.0.10.1 (Gateway for Voice Vlan 200) Ping Ok!!!!!
192.168.0.2 (Gateway for Internet Vlan 300) Ping Ok!!!!!
192.168.0.1 (Sky router & DNS) Ping OK!!!!!
My assumtion is if i have these settings on my home PC:
IP Address 10.0.9.55
S/M 255.255.255.0
Gateway 10.0.9.1
DNS Server: 192.168.0.1 (Home Router)
i should get internet access on my 10.0.9.1/24 network.
IP routing is enabled and inter Vlan is working correctly. The issue I have is I have no internet connectivity on Vlan 100 (10.0.9.1/24) from my desktop PC or any of my VM's on the 10.0.9.1/24 network and internet seems to be working fine on any device in vlan 300.
I have added my Running Config an attachment to give you a better understanding.
Please can someone find i solution as i desperately require internet access on my VM's but they need to stay on the 10.x.x.x subet due to CUCM licensing.
Kind Regards
Zubair
Hi,
It sounds to me like the home router (192.168.0.1) doesnt have a route back to your 10.0.9.0/24 and 10.0.10.0/24 networks.
Can you try a source ping from your 3750 switch as follows
ping 192.168.0.1 source 10.0.9.1
If this fails you will need to add static routes on the home router for the above networks with a next-hop of your 3750 192.168.0.2
Similar Messages
-
ASA 5505 VPN - how to access Two private networks
Hello
i have cisco 5505 and i confirgured a remote VPN clients. here is my sceniro
cisco switch 2950 === holds two private network 192.168.8.x and 192.168.4.x
vlan 2 outside interface - Eth0/0 155.155.155.x
Vlan 1 inside interface -- Eth 0/1 192.168.8.180
VPN pool ip address = 192.168.8.100 --110
i drag i cable from my cisco switch and put in to Eth0/1. and i want to access this twor private networks 192.168.4.x and 192.168.8.x .
now i can access to 192.168.8.x .
but i can't access 192.168.4.x .. please can any one help me that.
Regards
Thomasconfigure a split tunnel list that contains the networks you want the client to access.
Sent from Cisco Technical Support iPad App -
No internet access through hosted network
I created a hosted network to share the internet enabled the same. Both shared connection and the hosted network are showing 'Access type' as internet access, other guest devices are connected to the hosted network, got ip addresses also. But none of
the devices are able to access internet. I have tried disabling antivirus and firewall, but still the internet connection is not available to other devices.
Tried ‘Virtual router plus’. That also could not help in getting internet access, there in fact the internet connection sharing had to be enabled manually.
I had gone through similar issues, but could not see proper answer from an expert.
OS: Windows 8, Windows Firewall enabled
Antivirus: Trend Micro
Internet: USB modem (ICS enabled for the hosted network).
Any suggestions for resolving this issue would be highly appreciated. Thanks in advance.
PS: I could share internet using the same USB modem with a machine running Windows 7 using similar method.Hi,
Refer to this tutorial:
How to share internet from Windows 8 computer via WiFi without using Router
http://gallery.technet.microsoft.com/How-to-share-internet-from-ab8d6d35
if this issue persists, try to see if there is newest network driver for windows 8.
Alex Zhao
TechNet Community Support -
WRT54G configuration for internet access using Lacie Network Space Max
Please HELP!!!!
I have tried for the past 2 weeks trying to configure my router WRT54G so it allows me to access the Lacie over the internet without luck. I have followed every instructions from Lacie and every other FAQs and help on the internet, still no luck. I have spent numerous days with Lacie tech support and they could not figure it out - why my router would not allow me access over the internet. I am hoping that the big guns here can help me.
I have a number of laptops connected wirelessly to my local network and every laptop can access the Lacie NAS hardwired to one of the ports on my router. My entire system works wonderful locally.
The Lacie has been assigned a static IP of 192.168.1.199
My local network has a starting IP of 192.168.1.150 and ends at 192.168.1.199
My router's IP is 192.168.1.99
I have assigned port forwarding for my Lacie (192.168.1.199) for ports
20, 21, 25, 80, and 443.
I have tried other setups but no help. Please help!!!
Happy New Year!!!
Solved!
Go to Solution.Scrooge... thanks!
My NAS has ftp enabled. Access to the network is excellent throughout my local network. Every PC, wirelessly, can access everything on the NAS without any problem. Even when using the web browser using the IP or the dyndns.org assigned to the NAS. (I signed up for a free dynDNS)
The NAS can be accessed throughout the local network using explorer (under the network directory) and also by mapping the drive. The NAS can also be access using the web browser by either through its assigned IP (192.168.1.199) or by using the NAS's dyndns.org web address (web access requires login since it accesses the Network Space Max web page) - both by http and/or by ftp
My problem is accessing it through the internet outside my local network, i.e. from my work place or any other place away from home. The ability to access my data away from home is what I really wanted to be able to do.
"Open the setup page of the router and go to Status tab. Note down the Internet IP address.
Open the Internet browser and in the address bar type http://Internet_IP_address:21 or ftp://Internet_IP_address .
See if that works for ftp server."
Using the router's IP address for both format, http and ftp - I am not getting connected, even in my local network. Using NAS's static IP 192.168.1.199, I am able to access only using the ftp format. http://192.168.1.199:21 does not take me anywhere, but without the :21 takes me to the login page.
Again, thanks for all your help.... I am lost and I need your HELP!
v/r,
abelts -
Internet Access with a Networking Card
I have a macbook pro (for about three months) that has VISTA installed. ( I have been a PC user for about 20 years and will need time to learn about the MAC operating system). I bought a Verizon USB720 card to access the internet nationally through VISTA on the macbook pro. There may be some software in the computer that prevents my being able to use this card. The error message in effect says that someone is using this internet connection. I returned the first Verizon card and bought another card with the same error message. Any ideas what the problem may be? Many thanks EKL1
You probably need to set the card up in OSX. Verizon should have a modem script that needs to be installed. (Hard Drive>Library>Modem Scripts). Then you need to set up the card from Network Preferences. Then it should work on both platforms.
-
No internet access through hosted network in Windows 8.1
I am asking this question with a lot of expectation that I will get a solution for this issue. I have got seen a lot of questions being asked about this but there is no proper answer.
I use a USB modem in Windows 8.1 laptop. I want to share the internet to other devices by creating a hostednetwork. I used the netsh commands to create and start the hostednetwork. The wifi
hotspot got created as 'Local area network connection *14’. The internet from the USB modem was shared to ‘Local area network connection *14’. Other devices are able to connect to this and are getting IP address in the range of 192.168.137.X. The issue
is that, the devices are not able to access internet. Please help in troubleshooting this issue.
Please don’t give the instructions to create a hostednetwork or advice to use 'Virtual router plus'. I have already done all sorts of basic troubleshooting. Everything looks fine, but there is no internet connection to other devices.
I am able to share internet using the same USB modem with same method in Windows 7. Please let me know if any more info is needed.What is output from
ipconfig /all
route print
Rgds
Milos
Hi Milos
The details are given below.
ipconfig /all
=================
Windows IP Configuration
Host Name . . . . . . . . . . . . : XXXX-PC
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Mixed
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
PPP adapter Reliance Netconnect+:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : My Connection
Physical Address. . . . . . . . . :
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv4 Address. . . . . . . . . . . : XXX.XXX.XX.XX(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.255
Default Gateway . . . . . . . . . : 0.0.0.0
DNS Servers . . . . . . . . . . . : XXX.XXX.X.XX
XXX.XXX.XX.XX
NetBIOS over Tcpip. . . . . . . . : Disabled
Mobile Broadband adapter Mobile broadband 3:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Wireless Ethernet Adapter FFE9 #3
Physical Address. . . . . . . . . : 00-A0-C6-00-00-24
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Local Area Connection* 14:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Hosted Network Virtual Adapter
Physical Address. . . . . . . . . : 5E-85-DE-8B-77-0D
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::b0c8:44e8:1706:8f7e%13(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.137.1(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 241075678
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-18-33-18-B9-DC-85-DE-8B-77-0D
DNS Servers . . . . . . . . . . . : fec0:0:0:ffff::1%1
fec0:0:0:ffff::2%1
fec0:0:0:ffff::3%1
NetBIOS over Tcpip. . . . . . . . : Enabled
Wireless LAN adapter Local Area Connection* 11:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft Wi-Fi Direct Virtual Adapter
Physical Address. . . . . . . . . : 1E-85-DE-8B-77-0D
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Wireless LAN adapter Wi-Fi:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . : mshome.net
Description . . . . . . . . . . . : Qualcomm Atheros AR9485WB-EG Wireless Network Adapter
Physical Address. . . . . . . . . : DC-85-DE-8B-77-0D
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter 6TO4 Adapter:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft 6to4 Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2002:73f1:a3e::73f1:a3e(Preferred)
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 184549376
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-18-33-18-B9-DC-85-DE-8B-77-0D
DNS Servers . . . . . . . . . . . : 220.226.6.104
220.226.100.40
NetBIOS over Tcpip. . . . . . . . : Disabled
Tunnel adapter Local Area Connection* 17:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:0:9d38:6abd:10fd:35c3:8c0e:f5c1(Preferred)
Link-local IPv6 Address . . . . . : fe80::10fd:35c3:8c0e:f5c1%11(Preferred)
Default Gateway . . . . . . . . . :
DHCPv6 IAID . . . . . . . . . . . : 201326592
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-18-33-18-B9-DC-85-DE-8B-77-0D
NetBIOS over Tcpip. . . . . . . . : Disabled
Tunnel adapter isatap.{9B6DCE6D-CA03-414F-B9CF-9ADB7F37CEE7}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{45B50EE1-6A47-4BC2-994C-A7F5901B6141}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter #4
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
=====================================================================
route print
========
===========================================================================
Interface List
47...........................My Connection
39...00 a0 c6 00 00 24 ......Wireless Ethernet Adapter FFE9 #3
13...5e 85 de 8b 77 0d ......Microsoft Hosted Network Virtual Adapter
12...1e 85 de 8b 77 0d ......Microsoft Wi-Fi Direct Virtual Adapter
3...dc 85 de 8b 77 0d ......Qualcomm Atheros AR9485WB-EG Wireless Network Adapter
1...........................Software Loopback Interface 1
10...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
8...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
9...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #4
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 On-link XXX.XXX.XX.XX 41
XXX.XXX.XX.XX 255.255.255.255 On-link XXX.XXX.XX.XX 296
127.0.0.0 255.0.0.0 On-link 127.0.0.1 4531
127.0.0.1 255.255.255.255 On-link 127.0.0.1 4531
127.255.255.255 255.255.255.255 On-link 127.0.0.1 4531
192.168.137.0 255.255.255.0 On-link 192.168.137.1 4506
192.168.137.1 255.255.255.255 On-link 192.168.137.1 4506
192.168.137.255 255.255.255.255 On-link 192.168.137.1 4506
224.0.0.0 240.0.0.0 On-link 127.0.0.1 4531
224.0.0.0 240.0.0.0 On-link 192.168.137.1 4506
224.0.0.0 240.0.0.0 On-link XXX.XXX.XX.XX 41
255.255.255.255 255.255.255.255 On-link 127.0.0.1 4531
255.255.255.255 255.255.255.255 On-link 192.168.137.1 4506
255.255.255.255 255.255.255.255 On-link XXX.XXX.XX.XX 296
===========================================================================
Persistent Routes:
None
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
1 306 ::1/128 On-link
11 306 2001::/32 On-link
11 306 2001:0:9d38:6abd:10fd:35c3:8c0e:f5c1/128
On-link
10 1040 2002::/16 On-link
10 296 2002:73f1:a3e::73f1:a3e/128
On-link
13 281 fe80::/64 On-link
11 306 fe80::/64 On-link
11 306 fe80::10fd:35c3:8c0e:f5c1/128
On-link
13 281 fe80::b0c8:44e8:1706:8f7e/128
On-link
1 306 ff00::/8 On-link
13 281 ff00::/8 On-link
11 306 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
===========================================================================
The ip address is removed as this is a public forum. Please let me know if any more details are needed. Thanks. -
No internet access via guest network
I have setup up a guest wifi network on time capsule. Guests can connect to the network but the network does not allow them to access the internet?
That would be the issue.
The simplest fix would be to use the wireless on the Netgear for "guests".
Next option would be to ask your provider if they can supply you with a simple modem.....not a modem/router or gateway type of device.
After that.....not recommended.....you could try a different setting on the Time Capsule which would produce an error called Double NAT on the network....that may or may not allow things to work and create other problems as well. -
Internet access in different networks with proxy without proxy
at home i connect to a network with an internetaccess without proxy, in the enterprise I connect to a network with an internetaccess via proxy. How to configure the iPAD?
Hi Porras,
Try creating an exception for your proxy-server - see pics attached (Win XP SP3).
Note: These proxy exceptions can be created programatically, by modifying the Windows Registry.
Cheers.
"Inside every large program is a small program struggling to get out." (attributed to Tony Hoare)
Attachments:
net_proxy_adv.JPG 29 KB
net_proxy_adv_except.JPG 30 KB -
Set up internet access airport extreme network
Would like to set up old computer to airport extreme wireless network. Purchased a usb adapter. What next??
ThanksOK, but you might try these drivers, direct download link for 10.3 to 10.7 drivers...
http://www.bearextender.com/doc/BearExtender-v4.6.dmg
From this site...
http://store.bearextender.com/products/bearextender-for-mac?gclid=CMP2pNWLsa8CFS %20c0Qgod-mwiIA
Or these...
http://eshop.macsales.com/item/Newer%20Technology/MXP2802GU2/
http://eshop.macsales.com/item/Asus/USBN10/
Get a USB extension cable for these last two to give better range. -
No internet access when cellular network is available?
Folks, I'm looking for debug help. For two days now, I've had an almost complete lack of success in connecting to the Internet via my iphone.
Environment: new-since-march iphone 3G running OS 2.2, Wifi OFF, airplane mode OFF, 4 full bars ATT 3G. Can make cell phone calls.
Symptoms: third party apps (NYTimes, FB, etc) abort or timeout with a "check your internet connection". Integrated apps, like the Apps store, error with "cannot retrieve download info, please connect with itunes".
What should I try next?
skgReboot.
To reboot, press and HOLD both the HOME and LOCK buttons.
DO NOT let go when it says to slide to turn off, but keep holding both.
Screen will flicker off but DON'T let go.
Once you see the Apple Logo, then you can let go.
That is how to do a full cold reboot of the phone. No data or settings will be lost and only takes as long as it takes the phone to boot up.
This is the fix to just about every problem you ever may face with the phone (remember, it is a computer and a new OS at that. So reboots are needed now and then just to clear the cobwebs/memory leaks). -
Mac G5 Airport "NO internet Access" but is connected to WRT54G network
I have read thru prior threads and nothing has worked. I have connected to the internet once. I have upgraded the firmware to the wrt54. I have tried both PPPoe and DCHP to connect as well as using the built in ethernet. Why will it connect to the network but have no internet access?
The network status on my G5 says "Airport connected and You have internet access through Airport. But when I try through Safari, the screen comes up "no internet connection". Currently my wrt54 is 192.168.2.1 and I have set the security to allow access to the router. Can someone layout what my mac and router settings should be, If they are working for them? After trying somemany different things, I worry that I am not trying the right sequence of settings anymore. Help!
Many thanks!I have upgraded my router firmware to the latest, at least what is available here at linksys. The airport does retrieve the address from the router, but no go. Should it be set to PPPoe or not? If it isn't. it doesn't look for the host. When its off, the network status says connected to the linksys network, internet access through Airport, but still no Safari. I don't understand, if it is connected to the network, what is preventing it from connecting to the internet, which is available on the router? My DHCP server is enabled, I have changed the address to 192.168.2.1, 50 clients, but there are no DNS static address'. Should I input some DNS Address? My router is connected to a DSL modem and hardwired to a PC through the net connection. This is how I access the router. Whoops gotta get to work...........
Thanks for your help -
Help needed with internet access
I have just aquired a 5800 and I (think) I have turned of the 3G so it will only connect via my home WiFi unless it asks me. However, when I do connect I get a tiny little symbol which looks like 3.5g and the book says it is something to do with "HSDPA". It tells you that a line under it means "supported and active" and that a line through it means "a connection is on hold" but doesn't tell you what if there are no lines, just the symbol and what the flaming hell that means anyway.
My question is - when this is showing, am I doing something that I am being charged for ? On this phone I do not want to do anything chargeable without first being asked, so if anyone understands this minefield of information I would be eternally grateful for your assistance.
Solved!
Go to Solution.You can't normally switch off internet access via the network through settings, usually you get the following network options:
GSM only (which could could connect to the internet via GPRS)
UMTS only (this is 3G)
Dual mode (which selects 3G if the service is available in the area, otherwise defaults to GSM)
Your phone will always show the GSM or 3G signals if it is in range of such services, this does not mean that you are conencted to the internet by them. If you are connected via WLAN, you will not be charged for internet access over the internet.
One thing to be careful of is that if you leave the range of your WLAN router, the phone can automatically go for the next access available point in the "Destinations" setting, which could be your network. As long as you are in range of the router and it is working fine, you should have no worries. -
No internet access after 10.1 update
After downloading the 10.1 update to my Z10 my phone could not get Internet access through the network, although wifi still worked. Telus tech support had no idea what was wrong, and we found that the apn field in network settings was blank and could not be typed in manually. He said I might need to send my phone in for repairs. He called me back the next day to say this problem has come up for some people since the update and for a workaround to restore the phone to factory settings. However, if you turn your phone off the problem will come back so you can't turn off or restart your phone. I restored my phone and got Internet back over the network. Hopefully blackberry will have an update to fix this problem soon, I don't know how long I can go without having to turn off or restart my phone. Anyone else familiar with or experiencing this problem?
Hi man, I updated 3day ago my Z10 and I have the same problem I think. From time to time I get no internet connection by low or full mobile network. It has no reason, It´s just happened. Just like you wrote, reset or turning off/on the mobile helps not. But I don´t want reset my phone to factory default :-/ .
I hope Blackberry tech support works allready on this problem!!!
Come on Blackberry I need to work with my Z10 without problems! -
Do I need internet access on my iOS devices to enroll with Profile Manager?
Hi, I'm trying to configure Profile Manager on a closed network. The Mac Server does have Internet access, but the network for the iOS devices can only have communication with the server, but not to the internet because of company policies. Is there a way around to make it work or do I need internet access on the iOS devices as well?
I've made the enrollment process in another network with internet access for every device and everything works well, but on the other network(no internet for iOS devices) everything seems ok (from conection to the server, profile certifiacation and stuf) but the devices can't send or receive anything else, like pushed configurations and device info. Ports and everything is ok, I even read that they need to be on an open network so I know it all comes down to having internet access, but just wanted to ask if there's another way around?? Suggestions?
Thanks!You can share internet connection with your XP-PC using a router(as I do with XP-old MAC's,connected via cable).You may look for more info at:
http://homepage.mac.com/car1son/mylinksyssetup.html
and
http://homepage.mac.com/car1son/os9xnet_nfilesharing.html
Did you ever use a MAC before? Have you got Airport at your PC?Which?
Good luck -
Airport Extreme - Remote is not passing internet access - help please
I have the following:
Cable modem - > WAN of Airport Extreme. - works perfectly - wireless clients in range get internet access and the network works.
Second Airpot Extreme set to relay this network. It connects, gets a "green" light - seems to be set up properly, but wireless clients in that area cannot get internet. Why is it not passing internet.
Can anyone explain step by step how to do this or post a link to an apple doc?
Thank you,
Miklos.Hi, actually this is still not working.
I got the second base station configured so that when it started up, it was working properly as a "remote" station, and I was getting internet fine through an ibook there (which is normally too far away from the main station to get any signal).
However, today, although the second "remote" station still has a green light and is connected to the network it is not getting an IP address from the main base station - and so I can't get any internet through that 2nd base station anymore.
Why was it working yesterday and not today when I've changed nothing?
Any help much appreciatd.
Miklos.
Maybe you are looking for
-
Mass generation of sales orders from marketing projects
Hi, I am trying to create sales order from a campaign. I get an error message: Sales orders are only generated when products and quantities are assigned. I have added a quantity in the order template, but from the campaign the is no field available f
-
No stock posting for this material
I have create a material with item category LEIH for returnable packaging,while doing stock posting in MB1C error comes as "No Cmaterial posting for this material".plz help how to post the material.
-
How to accept input Text in UpperCase?
Hi, How to accept Character Text from users in UpperCase in inputText Field? I am using ADF BC and Jdev10.1.3.1. In forms world it is very simple ( setting the visual attributes ), I am searching for such simple solution in Jdev . Regards, Seshu.
-
When Does Time Capsule Actually Stop Backing Up?
I have tried backing up my system using Time Machine and my Time Capsule a number of times without success. I have 144GB of data to be backed up - I guess that should equal about 172.78GB in a Time Machine backup (with a 20% buffer). But, I am now at
-
Revision: 3403 Author: [email protected] Date: 2008-09-29 12:36:37 -0700 (Mon, 29 Sep 2008) Log Message: Fix for SDK-17097 - Missing summary description of a class in package classes table QA: Yes Doc: Tests: checkintests Ticket Links: http://bugs.ad