No SIP 200 OK after Q.931 CONNECT

Cisco AS 5350 configured as H.323 Gateway on CUCM.
Call flows from SIP to H.323.
Inbound dial-peer
dial-peer voice 43 voip
session protocol sipv2
session target ipv4:10.20.8.11
incoming called-number 322####04
voice-class codec 1
Outbound dial-peer
dial-peer voice 103 voip
destination-pattern 322####04
session target ipv4:10.20.8.6
voice-class codec 1
I see messages exchange
SIP: Recieved INVITE -> Sent 100 Trying
Q.931: SETUP -> CALL_PROC -> ALERTING
SIP: Sent 180 Ringing
Q.931: NOTIFY
SIP: Recieved PRACK -> Sent 200 OK -> Sent UPDATE -> Recieved 200 OK
I pick up the phone
Q.931: CONNECT -> NOTIFY
And then Nothing! No SIP signaling. No 200 OK.
As a result I hear ring back on the calling side, and silence on the called one.
Please, help. What's wrong with it?
Oct 1 09:35:47.692: h323chan_chn_process_read_socket: fd=2 of type CONNECTED has data
Hex representation of the SETUP TPKT received: 08028DAD0704038090A24C060081313130307E006B0522C0060008914A0005000A1408069F4B22C0B50000120F436973636F43616C6C4D616E6167657200310000F42F50F1CAB1421E0254020A140E041D0C001100277F9807488511E4833DE2C8A6D0856E0100010010A00100120140B50000120B8204020004000103000100
Q931 Message IE Decodes
Protocol Discriminator : 0x08
CRV Length : 2
CRV Value : 0x8DAD
Message Type : 0x07: CONNECT
Bearer Capability: Length Of IE=3
Data 8090A2
Connected Number: Length Of IE=6
Data 008131313030
User-User: Length Of IE=107
Data 0522C0060008914A0005000A1408069F4B22C0B50000120F436973636F43616C6C4D616E6167657200310000F42F50F1CAB1421E0254020A140E041D0C001100277F9807488511E4833DE2C8A6D0856E0100010010A00100120140B50000120B8204020004000103000100h225ParseData: Q.931 CONNECT received on fd=2
Oct 1 09:35:47.692: Changing to new event: CONNECT
h323chan_chn_connect: connecting to 10.20.8.6:40779
Oct 1 09:35:47.692: h323chan_gw_conn: Created socket fd=3
Oct 1 09:35:47.692: h323chan_gw_conn: connect in progress on fd=3h323chan_chn_connect: using fd=3, owner_data(ccb) 0x69BFC32C
changing from NONE state to CONNECTING state
Oct 1 09:35:47.692: h323chan_chn_process_read_socket: fd=2 of type CONNECTED has data
Hex representation of the SETUP TPKT received: 08028DAD6E2701F14C060081313130307E00210528501900060008914A000500277F9807488511E4833DE2C8A6D0856E10800100
Q931 Message IE Decodes
Protocol Discriminator : 0x08
CRV Length : 2
CRV Value : 0x8DAD
Message Type : 0x6E: NOTIFY
Notification Ind: Length Of IE=1
Data F1
Connected Number: Length Of IE=6
Data 008131313030
User-User: Length Of IE=33
Data 0528501900060008914A000500277F9807488511E4833DE2C8A6D0856E10800100h225ParseData: Q.931 NOTIFY received on fd=2
Oct 1 09:35:47.692: //-1/xxxxxxxxxxxx/SIP/Error/ccsip_call_service_msg: ccb NULL, unable to update the callinfo ui parameters
Oct 1 09:35:47.692: h323chan_chn_process_read_socket: fd=3 of type CONNECT_PENDING has data
Oct 1 09:35:47.692: Changing to new event: CONNECTED
hq_as5350xm_gw1#changing from CONNECTING state to CONNECTED state
Oct 1 09:35:47.692: h323chan_chn_process_read_socket: fd=3 of type CONNECTED has data
Oct 1 09:35:47.692: h323chan_recvdata: No Data on fd=3
PROCESS_READ: FAILED/NOT COMPLETE,rc 10, fd=3

Please configure the ff and send the logs
service sequence-numbers
service timestamps debug datetime localtime msec
logging buffered 10000000 debug
no logging console
no logging monitor
default logging rate-limit
default logging queue-limit
Then..
<Enable debugs, then test again.>
debug ccsip messages
debug h225 asn1
debug h245 asn1
<Enable session capture to txt file in terminal program.> (such as Putty)
then do the ff:
terminal length 0
show logging

Similar Messages

My ipod touch says "activation required, connect to itunes" i restore it on my itunes and it seems to be working, after i tried connecting to my wifi but no luck, i reset it and the same thing happens all over again. Help!

my ipod touch says "activation required, Connect to itunes" i restored it with on my itunes and it seems to be working again, after i tried connecting to my wifi with no luck i reset it, and again it pops back "activation required, connect to itunes" i restored again, its a non ending cycle, and it makes no sense having my ipod and i cannot connect to the internet with it, can someone please help with this issue?

Maybe here:
Restore loop (being prompted to restore again after a restore successfully completes)
Troubleshoot your USB connection. If the issue persists, out-of-date or incorrectly configured third-party security software may be causing this issue. Please follow Troubleshooting security software issues. .
Next would be to make an appointment at the Genius Bar of an Apple store.

After that I connect my Iphone 4 to the computer for syncronization the phone does not working and it is not possible to connect to i-tunes . On the screen on Iphone it is just an apple and a small frame benite the apple

After that i connected my iphone to a computer there was some errors and the phone stopped to work and there is just an apple on the screen on the phone and when I connect to i-tunes it is not any phone connected

Unable to Update or Restore
http://support.apple.com/kb/HT1808
iPhone, iPad, or iPod touch not appearing in iTunes
http://www.apple.com/support/itunes/troubleshooting/

TS3297 Even after having data connectivity can't open iTunes,app store and iBooks

Even after having data connectivity can't access iTunes ,app store,iBooks

I have the same problem. The install seemed to go fine, it rebooted and the only APPLE app I can use is Safari and Itunes, The Mac Apple store freezes, Ibooks, Iphoto etc, all of them just lock up when I open them, even drop down items under the little Apple are frozen. I'm disgusted, any help would be appreciated.

CSCsm80678 - SIP-200 logs " percentSIP200_SPIRX-3-SPA_INTERRUPT" error message continuously

We recently upgraded our C7609-S routers to 12.2(33)SRE8 version. Post a month of these upgrades, I am continuously getting the SIP-200 related alarms on one of my routers which matches with bug id CSCsm80678.
Only IOS version 12.2(33)SRB1 is mentioned as affected release. Is SRE8 also affected?
What is the workaround for this bug so that I can avoid these errors in my router?

That bug is a duplicate of CSCsq19146, which will contain the fix information
A fix was applied to:
12.2(33)SRC02, 12.2(33)SRB04 and 12.2(33)SRD have the fix, so it would seem that SRE should have inherited it.
What version did you upgrade from? This may merit a TAC case.

GX520 hangs after establishing server connection

We are running ZFD 6.5 sp2 and trying to image new GX520's
There are 21 machines all exactley the same down to every last BIOS line,
DELL GX520.
I used the bootcd.iso from SP2
Set up a policy to install an image to any PC booting within a given IP
range.
Here is the issue:
I installed the boot loader on all twenty PC's
7 PC's took the image just fine
14 hung with no error after establishing server connection and the path
to the image.
Zimglog.xlm shows
- <WS DN="R3NWTS01.R3.usnrc">
<Tree>NRC_TREE</Tree>
<Status>Failure</Status>
<ErrorMessage>Workstation failed to restore image as the base image
already exists.</ErrorMessage>
<Operation>Download</Operation>
<ImageType>Base Image</ImageType>
<ImagePath>\\R3NWTS01\NRC\zen-img\train2.zmg</ImagePath>
<Timestamp>Tue Apr 11 12:13:08 2006</Timestamp>
When I try a manual download I get "no eligible partitions to recieve
Image"
Any thoughts?
Thanks
Thomas Magee
US NRC
Network Manager
[email protected]

Tmm3,
It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
- You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

After a call connects, my iphone 4 makes a jackhammer sound in my car only. does not happen in other cars. what is going on with my car to interfere with reception?

after a call connects, i can hear a loud jackhammer sound on my phone. the other end can hear it too. only happens in my car so i am thinking something in possibly my ignition is giving off a signal?? any suggestions?

What troubleshooting steps have you taken so far?
Restart?
Reset?
Reset All Settings?
Restore From Backup?
Restore As New?

IPhone 5s won't automatic connect to cellular network after the wifi connection lost.

My iPhone 5s won't automatic connect to cellular network after the wifi connection lost. I have try make a restore and open again my cellular data but the problem is still there, after I try to restart my iphone then can use my cellular data, but after few hour ago I still confront the same problem too.

I also tried a total reset. But it didn't work.

Nothing can be run after internet is connected

After recent updates, my gnome sucks. (Tried xfce4, it works.) The problems is that no software can be run in gnome after the wireless connection is established.
I tried to disconnect it, and then everything worked just fine (of course, without internet). In that case, I opened a terminal, and reconnected the internet, and tried to do something:
$sudo gedit /etc/rc.conf
Password:
No protocol specified
$dropboxd
No protocol specified
Everything I did ended up with a "No protocol specified".
How can I fix this problem?
Last edited by sfbi (2010-09-29 08:52:23)

sfbi wrote:
wonder wrote:this sounds like network manager (if this is what you use for your wireless) is changing your hostname and /etc/hosts.
Yes, I am using network-manager. Then, how can I fix it? Cheers.
to really fix this, you should help writing a backend for archlinux. We do patch networkmanager to not do that but seems there is another case which i can't figure it out.
maybe your dhcp server is sending you the hostname?

FileSharing Transfer Speed Drops after sharing internet connection

Hi Folks
Sometimes, when I copy files via FileSharing,
the speed drops exactly to the max. upload speed my internet connection has.
= instead of 12 MB/s I got 600 ~700 KB/s.
I needed a bit of work to see this connection.
But after a while, it changes back to normal.
However, I did share the ethernet-internet-connection from one machine via WiFi (to surf with an iPod Touch).
Could that initiate this problem? I believe so.
Internet-Provider is cablecom, switzerland, zurich.
I use a Zyxel Ethernet Switch to connect two macs with the cablecom-modem (and together).
So Idetached the cablecom-modem from the ZyXel Switch and restarted both machines.
Now, the copy-action via filesharing has the expected full speed. (Just no internet, of course).
After that I connected the Cablecom-Modem again,
restarted (PowerOff/On) the ZyXel Switch,
and tried the same again:
Now the speed is slow.
It seems that I really should NOT share the Ethernet Internet Connection with WiFi
Won't do that anymore because I often copy files from one machine to the other and this slow transfer speed kills me.
Why is that affecting the connection between two local machines?
How can I reset this to "normal".
I hope there is a way to do it in OS X instead of waiting until it sets itself to "normal" from cablecom's side.
[ -Despite the fact that I should use a wireless router- ]
Is there any chance that this is an issue that OS X could resolve?
Best would probably be: the local connection between two machines should not be affected by the provider in any circumstances.
BTW: The cablecom-modem gives - via a ZyXel Switch - both computers unique IP's and they are reachable/visible from the internet.
Greetings from Zurich
Alain Burki
If my English is bad
please forgive me

I am doing the same thing (have tried it occasionally over the past 6 months or so and cannot install Arch because of it)...sad panda. The downloads start fast (up to 5MB/s), then when it gets to 49% it slows all the way down until it gives up and moves to the next mirror, repeating and repeating and repeating until finally it shows:
core is up to date
error: failed to update extra (download library error)
error: failed to update community (download library error)
:: There are 51 members in group base
:: Repository core
Enter a selection (default=all): error: failed to prepare transaction (could not find database)
I've tried commenting out the XferCommand and using wget but that fails even worse.
Thank you for posting this, I am glad I am not the only one experienceing this. I was about to give up searching and post too.

After VPN is connected...

I'm trying to setup my Mac mini with Snow Leopard server VPN connection.
With a Macbook and a 3G dongle I can connect to the server via VPN.
After the VPN connection how do my Macbook "see" Public and Users folder?
I've enabled Bonjour in the DNS setting.
I've tried from Finder "Connect to Server" with afp://xxxxx.com but it won't connect.

Hi
Over a VPN connection you don't 'see' anything unless you're prepared to work very very hard. This is how VPN is supposed to work.
From the Connect to Server dialog box use the Server's IP address instead. This won't be the external IP address. If you've started the AFP service you should see a prompt for a user name and password. Supply them and you should now have access to any defined shares that account has been given access to.
Assuming you've configured everything else correctly you can use the Server's hostname but only if you've configured the DHCP Service to hand out the appropriate DNS Server address.
Tony

Cannot connect to iTune store... even after the internet connection is working fine... plz help...

cannot connect to iTune store... even after the internet connection is working fine... plz help...

Same here, also cannot access the App Store. Internet connection is good. Iam on a Mac

Ipod runs out of battery after its been connected to pc.

Hi my Ipod has ranout of battery after its been connected and charging through my pc. It was connected for a good few hours and when i disconnected and i went to play an album, i get the message - "please connect to power". I cant understand why it runs out when it says charging (the lightning bolt) and then battery fulll (the plug symbol). This has happened a couple of times now, i would be greatful for any help or insight into this. Thanks.

My computer doesnt go to sleep, the ipod still says connected, so still not sure whats happening. It doesnt happen all the time, so funk knows, cheers anyway. Maybe the new firmware will fix it. Any ideas to when its due out?
Message was edited by: adamski82

Hp laserjet Pro 200 M276nw won't consistently connect wirelessly with iMac

I'm on my second brand new hp laserjet Pro 200 M276nw in 3 days, it will not consistently connect wirelessly with my newly purchased (8days old) Apple refurbished 27" iMac on OSX 10.9, i7 chip & Fusion Drive. The hp laserjet will sometimes connect wirelessly immediately after clicking "print" on the iMac, but about half the time it says "printer not connected" & takes 2-4 minutes (or longer) before the devices do connect. I've called hp support many times, they're reset various things via remote takeover of my iMac, the printer will work for a few of minutes but then the same problem returns. AppleCare made sure I have the
correct Airprint driver installed & also checked my settings, but says they don't know why this is occurring. I've also verified that our newer (6 months old) AT&T router is functioning correctly.
My older hp laserjet (CM1312nfi MFP) has worked flawlessly since 2009 via USB connection with my old iMac (still on Snow Leopard), I assumed it would continue with the new one, but there is no software update for Mavericks & the scanning feature won't operate on the new iMac. Hp says it is a discontinued model. The new hp laserjet is a successor model to the older one, they are both very similar except for the new wireless feature.
I can print fast & wirelessly from the new iMac via a different new hp inkjet printer (8600 series) here in the house. This inkjet printer is less than a month old, I installed it myself for a Windows laptop here, it has never malfunctioned. Unfortunately it's upstairs & I do not like inkjet print quality, I need a good laserjet here in my office downstairs next to my iMac.

HI there
Did you manage to sort this issue out - as I have exactly the same problem.
Lots of similarities as I also have an inkjet 8600 which works via USB and wirelessly no problems at all!
I always buy HP printers as they are usually easy to set up - but this one is making me tear my hair out!
I've even upgraded to Yosemite and downloaded the new drivers from HP - no success. The printer will print one page and then become unavailable.
I can print via USB or wireless direct - but not just via my wireless network which is what I want to do!
No responses posted - so assume no one has a fix.
aaaargh!!!

No SIP 200 OK after Q.931 CONNECT

Similar Messages

Maybe you are looking for