No volume available in RMAN-default family

Just a green hand with osb. Any suggestion is welcome. Thank you.
OSB :10.2.0.3
Oracle: 10.2.0.1
Tape Drive : DELL POWERVAULT 122T DLT VS80
OS:windows server 2003
When i try to access OSB devices and media from EM, it sits without anything or message until EM session expires.I don't know what's the problem.
There is no problem with the OEM disk backup.
Osb user ‘ admin’ can back up data to tape(use OSB-CATALOG-MF family) ,it work well, not only General document but database file (except for the library can’t attach to //./obl0)But user ’oracle’ cannot do this 。
it shows error：
The volume in tape0 is not usable for job oracle/9.1.oracle/9.1: A volume usable for media family RMAN-DEFAULT is needed to perform a backup.
It seems that osb cannot distribute volume for family RMAN-DEFAULT。
Backup with the Rman command, once the backup start it pending, and then stopped there until you cancel this job.The same error it shows：
The volume in tape0 is not usable for job oracle/9.1.
oracle/9.1: A volume usable for media family RMAN-DEFAULT is needed to perform a backup.
Login with user ‘Oracle’ OSB administrator wed tool, once you want to backup (operation: backup now)
error：can’t sent message to background process – wrong user id tried to connect.
How can I configure the osb that I can backup with the Rman command?
thanks，
lotus
ob> lsdev -lvg
tape0:
Device type: tape
Model: [none]
Serial number: [none]
In service: yes
Automount: yes
Error rate: 8
Query frequency: 1024KB (1048576 bytes) (from driver)
Debug mode: no
Blocking factor: (default)
Max blocking factor: (default)
UUID: a589640a-f79f-4917-8780-774df5efd581
Attachment 1:
Host: user2
Raw device: //./obt0
ST controller: 0
ST target: 6
ST lun: 0
Connection type: SCSI
Inquiry data:
Vendor: BNCHMARK
Product: VS640
Firmware: 5639
Serial number: PHD2F07363
WARNING: drive type is unrecognized
Tape state: online
Hardware compression: off
Last read was: compressed
Maximum block size: 65536
Remaining tape: 0 (uncompressed) blocks (0.00KB)
ob>
one competed job details：
4.1: 2009/08/05.00:01:04 ______________________________________________________________________
4.1: 2009/08/05.00:01:04
4.1: 2009/08/05.00:01:04 Transcript for job 4.1 running on user2
4.1: 2009/08/05.00:01:04
4.1: Warning: unknown device type. This device is not supported by Oracle Secure Backup
4.1: Warning: and is therefore not guaranteed to work with Oracle's driver.
4.1: Warning: unable to set compression on: bad parameter (OB scsi device driver)
4.1: Backup started on Wed Aug 05 2009 at 00:01:23
4.1: Volume label:
4.1: Volume UUID: 4f9b5d05-6823-4c8d-870a-412a69ad6d48
4.1: Volume ID: OSB-CATALOG-MF-000002
4.1: Volume sequence: 1
4.1: Volume set owner: SYSTEM
4.1: Volume set created: Tue Aug 04 16:30:04 2009
4.1: Volume set closes: Tue Aug 11 16:30:04 2009 (no writes after this time)
4.1: Volume set expires: Tue Aug 25 16:30:04 2009
4.1: Media family: OSB-CATALOG-MF
4.1: Original UUID: 4f9b5d05-6823-4c8d-870a-412a69ad6d48
4.1:
4.1: Archive label:
4.1: File number: 4
4.1: File section: 1
4.1: Owner: SYSTEM
4.1: Client host: user2
4.1: Backup level: 0
4.1: S/w compression: no
4.1: Archive created: Wed Aug 05 00:01:23 2009
4.1: Encryption: off
4.1:
4.1:
4.1: Dumping E:/oracle/product/10.2.0/oradata/orcl/USERS01.DBF
4.1:
4.1: Backup complete on Wed Aug 05 2009 at 00:01:43
4.1:
4.1: Backup statistics:
4.1: status 0
4.1: devices tape0
4.1: devices 1
4.1: volumes OSB-CATALOG-MF-000002
4.1: voltags (null)
4.1: file 4
4.1: host user2
4.1: encryption off
4.1: start_time Wed Aug 05 2009 at 00:01:23 (1249401683)
4.1: end_time Wed Aug 05 2009 at 00:01:43 (1249401703)
4.1: backup_time Wed Aug 05 2009 at 00:01:23 (1249401683)
4.1: entries_scanned 1
4.1: kbytes_scanned 0
4.1: entries_excluded 0
4.1: entries_skipped 0
4.1: mount_points_skipped 0
4.1: files 2
4.1: directories 0
4.1: hardlinks 0
4.1: symlinks 0
4.1: sparse_files 0
4.1: filesys_errors 0
4.1: unknown_type 0
4.1: file_kbytes 0
4.1: dev_kbytes 5257
4.1: dev_iosecs 20
4.1: dev_iorate 269.2 KB/S
4.1: wrt_iosecs 14
4.1: wrt_iorate 384.5 KB/S
4.1: physical_blks_written 5892
4.1: write_errors 0
4.1: physical_blks_read 4027
4.1: read_errors 0
4.1: error_rate 0%
4.1: path E:/oracle/product/10.2.0/oradata/orcl/USERS01.DBF completed, status 0

Can you post the output from "obtool lsvol -L <library_name> -l" so we can see the volume details?
Thanks

Similar Messages

I use my iphone 3G to listen to radio stations. Now get "no volume available" message. Anyone had this problem?

I use my iphone 3 to listen to radio stations. Now I'

I just found the earbuds that came with the phone still in the box, plugged them in & it's letting me listen to radio.com. When I unplug them I go back to 'no volume available'.

Pandora app - iPhone 4 - docking - "no volume available"

My pandora app on my iPhone 4 worked fine last week when I would dock it into my Sony alarm clock. now- when I dock- I am receiving a "no volume available" message on my phone & the sound stops.

hmm.. My phone always says "no volume avaliable" when i have it connected to exterior speakers (using the 30 pin music connector) but volume always works.. its just not adjustable. are you sure your speakers havent broken?

HT1349 My ipod say no volume available and therefore I have no sound thru the earphones

My ipod says no volume available and therefore I have no sound in the earphones or thru an aux cable.

- Have you tried a reset. Nothings will be lost.
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Do the speakers work?
- Have yo tried another pair of headphones?

PANDORA -No Volume available

I am trying to use PANDORA It says on the screen-No Volume available...but if I plug in my earphones...i can hear it. It worked on speaker before...what do i need to do?

My ipod touch does the same thing but head phones dont work either..PLEASE HELP

I keep getting the message "no volume available" when I hook my iPad up to my TV to watch netflix, does anyone know how to fix this?

I am trying to hook my iPad up to my TV so I can watch netflix on it, however, when i hook the AV cable up i get a message that says "no volume available." my iPad is not muted, does anyone know how to fix this problem?

Read this link and it may provide some help: https://discussions.apple.com/message/15460209#15460209

Are in app purchases available for download on family sharing

Are in app purchases available for download in family sharing

No. From Which purchased content can I share using Family Sharing - Apple Support:
There are a few things that you can't share:
Songs added to iTunes Match from outside the iTunes Store
In-App Purchases
Items that are no longer available on the iTunes Store
Items that were hidden
Apps that aren't shareable

Audio stopped working only getting 'dock connector'/ 'no volume available messages

Last week, my iPad2 suddenly stopped producing external sound e.g. radio with the message of 'no volume available' coming up. Switching to the iPod app, the mesage of 'dock connector' appears.
I can hear everything if I insert my headphones but this is not practical for me as I move about the house/ workstation.
I am presently overseas and I've already run through every suggestion from Apple's Help line experts with no fix.
From review other message boards, this seems to be a growing probblem. Any advice from anyone?

Solution discovered: The iPad had not been properly ejected when last docked to my laptop. Please ensure that you get the 'Eject' prompt when you right-click. If you do not, try to eject via iTunes programme on PC/ laptop. If 'Eject' prompt is still not present, take out Apple USB and re-insert into the PC dock (or another USB dock location on the computer) as it is not being recognised by iTunes or PC/ laptop. 'Eject' command should then appear and you then click on it. Voila!

Bronze G3, new drive: no volumes available. How come?

Hey all,
I have a PB Bronze G3 333/512, and I've just installed a Samsung 40GB Spinpoint M 5400rpm drive. When trying to install Panther, I see no volumes available (as in no icons at all in the "Select a Destination" screen).
The drive has two NTFS partitions on it from a previous XP install. Does this prevent 10.3 from seeing the drive as a viable volume for install (ie: is Panther "non-destructive)?
I have reset the PRAM with no luck. So, my questions are:
1) Do I have to manually kill these partitions on a Windows machine before I can install 10.3?
2) Is there a way of deleting partition information during the Panther install process? I expected to see one, but maybe I'm missing something.
3) Is there a way I can check to see if the PB even sees the drive? I feel kind of "blind" here, because there's no evidence during the install that the drive even exists.
I'm sorry if these are stupid questions (I've searched), but I'm kind of new to the Mac scene.
Thanks for any help!
Ugli
PB Bronze Mac OS X (10.3.9)

Ugli:
If you can boot from the Panther install CD, go to the Installer menu and open Disk Utility. You should see the HDD there. Select the manufacturer ID in the left panel, and Erase in the main panel. Make sure the Volume Format is set to Mac OS Extended, and the Install OS 9 Drivers checkbox is checked. Name your volume. You can just click erase, or select Options and choose to zero all data. This process takes several hours but it completely erases the HDD. Your volume should then show up for installation after you quit DU.
Good luck.
cornelius
PismoG4 550, 100GB 5400 Toshiba internal, 1 GB RAM; Pismo 500 OS X (10.4.5) Mac OS X (10.4.5) Beige G3 OS 8.6

Delete all AVAILABLE valid RMAN backup by RMAN command

Hi
We are taking RMAN full backup on disk every day. But right now we don’t have enough space on RMAN backup mount point. So we want to delete all AVAILABLE valid RMAN backup by RMAN command.
Please guide to delete all AVAILABLE valid RMAN backup by RMAN command.
-Thanks
Edited by: Fazlul Kabir Mahfuz on May 13, 2013 11:06 AM

You can do it by manually delete the backups and archivelogs from OS location. Then use below commands
RMAN>crosscheck backup;
It will give status as EXPIRED for backups which are valid but not available at OS level.
RMAN>delete expired backup;
Delete all the backups whose status are EXPIRED from database level.
Similarly for archivelogs
RMAN>crosscheck archivelog all;
RMAN>delete expired archivelog all;

'No Volume Available' but headphones work

Weird problem just cropped up today on my iPhone 4 (no longer under warranty). If I try to play the Music app, Pandora, YouTube and many other sound apps I can't hear the audio over the speaker and on some apps a message appears saying 'No Volume Available' on the screen. It has this message in Pandora, in YouTube and the music app just don't have the volume slider.
If I plug in headphones all work normally.
If I use the Phone app, or Talkatone I can hear the audio via the earpiece and I can switch it to the speaker. So I know the speaker system works as some apps detect the speaker and can route audio through there. Skype on the other hand works via speakerphone but not via the earpiece. Key-clicks and lock sounds don't work via the speaker.
I've reset the iPhone a few times, 2x via holding down the power key and shutting it down then restarting with the Apple logo and once forcing a shutdown via power+home buttons.
I've restored the iPhone, I'm running iOS 5.0.1, bluetooth is off, mute switch on the side is on (I've switched it both on and off, didn't do anything). I've tried plugging/unplugging in headphones to see if debris or something would be knocked loose but that didn't work. Plugging/unplugging dock connector several times didn't work either.
I'm wondering if an app I tired did something weird electrically? I had a headphone jack plugged-in and ran the TASCAM recording app to try and record something. Had a tough time figuring it out and it was while I was trying it that the problem seemed to occur as I couldn't hear anything recorded via the app.
I've since removed the app and done all of the above to no avail. I'm going to try another restore. And don't suggest I just go to an Apple Store, the nearest one is a few hundred miles away on another island.

I went to an Apple Store and let a 'Genius' check it out. First thing he says is that the water damage indicator was activated in the bottom dock connector. I've never dropped my iPhone 4 in water though I probably do live in one heck of a humid place so maybe that's why it activated. He had opened it up and I asked him if there was any indication at all if there was water damage in the iPhone and he said 'no.'
I let him wipe the phone since I had it backed-up via iTunes. Then it started to work and thought we had it fixed but then all of a sudden it stopped producing sound again. This is with no extra apps loaded on it and right there at the Genius Bar with the Genius there. He operated the controls and was just stumped.
He said because it was out of warranty I could get a replacement one there at Apple for (I forget) something like $149, or I could wait a few week when I can get an early upgrade to an iPhone 4S for $199 (that would only be for the 16GB model, mine is a 32GB iPhone 4).
So yeah, the Genius couldn't figure it out. The phone's sound continues to have this problem along with the problem, which I hear many people have, of the home button being disfunctional at times. The iPhone 4 is a flawed design in so many ways: Antenna, Home Button, Audio System, Lower Battery life with iOS 5.

I am getting a no volume available on Pandora

I get a message when opening Pandora that says ' no volume available'

Hello , I would like to help you with your fax setup, but can you specify your exact printer model for me? In your title you have specified a laserjet m1217nfw, and in the body of the post a Pro 6830.How Do I Find My Model Number or Product Number? Here are some helpful documents for the laserjet m1217nfw;Setting up the FaxSending a FaxFaxing with VoIP Services As well as a document for the Pro 6830;Sending and Receiving Faxes, Set up the printer for faxing I would also need some more information about your fax/phone line setup to assist you further;Is this a Dedicated phone line? Only being used for faxing.Or is it a Shared phone line? Phone and Fax.Is your phone provider Analog (Typical Phone lines) or Digital? (Cable Connection)If the line is shared;Do you have Distinctive ring service? 2 numbers, same phone line that have different ring patterns to indicate teh type of call coming inDo you have an Answering machine? An answering machine answers voice calls at the same phone number you use for fax calls.Do you have Voice mail? A voice-mail subscription service uses the same phone number as the fax. Please let me know if any of these steps resolved your issue, or if there is anything else I can do to help. I look forward to hearing from you! Thanks,

Prefs code show server volumes in sidebar by default?

I support a K-12 installation of around 4000 Macs, roughly 1000 of which are now running Leopard. I'm creating a new image for these systems, and cleaning up glitches, including this one:
In Tiger, mounted server volume names appeared in the sidebar below the hard drive icon in any Finder window. When you click on the volume name, the contents of that volume are immediately available as any regular disk would be. When you click the eject icon beside the volume name, only that volume is ejected.
In Leopard, the server name appears in the sidebar instead of the volume name. The server name is not particularly meaningful, since it's the volume name which our users recognize. When you click on the server name, a list of available volumes appears after a longish pause. This also creates confusion ("what are those other names?" "can I save there?" "why do these appear?"). When you click the eject icon beside the server name, all mounted volumes are ejected. Many of our education applications don't handle well this new way of accessing server volumes -- some crash, some hang when you click on the server name instead of a volume name. This is a serious reduction in ease of use for our end-users! Now they have to deal with the confusion of clicking on an unfamiliar item like the server's name, then figure out which share they want to use, and finally save their document ("why can't I save to the server like I can save to my USB key?").
I haven't yet found a way to reproduce Tiger Finder's shared-volume-in-the-sidebar behaviour as a default, beyond manually dragging each server volume to the sidebar (not an ideal solution, since volume names change, and servers change). Is there some XML key I can add to the Finder prefs to revert to the old way of displaying server volumes in the sidebar?

Hi,
I have the same problem (and there are threads archived starting 2007 dealing with the same issue) This is not a SERVER problem. Its simply that the 10.5 finders sidebar does not show mounted volumes or mountpoints anymore. Instead of that you see whole servers, which makes navigation slow.
Any way to get TIGERS behaviour back?

Using an available upgrade from another family member on my plan???

Hello all,
I want to upgrade my 3G to the 3GS. I have an AT&T Family Plan. My wife's V1 iPhone account is upgrade available now.
I want to give her my 3G and use her upgrade on my new 3GS......
I was hoping to just upgrade her phone, then later swap SIM cards to get our phone numbers straight. Ive done this with other phones in the past, but I think that iPhone is SIM specific......
How should I try to make this happen without confusion. I don't want to overwhelm the local AT&T store salesman.
Your advice would be appreciated.
Thanks
Donald

I have been able to switch iPhones with someone on my family plan, trading 3G for 2G. I also want to buy 3GS using one line that is eligible for upgrade and then trade phones so I get the new one. I was planning to activate it from home on the eligible line, then backup, swap sims, then restore. This is procedure I had used before and worked swapping 3G and 2G phones. I think as long as they really want to get you for a 2 year contract, so may not matter what phone you have, as long as you also pay the new $30 data charge.

Rman default configured fine and in v$rman_configuration but cannot display

using RMAN show all; or show default device type;
anything I missed? thanks.
- Zack

You pretty much hit the nail on the head. Thank!
Just didn't realize I needed to set the text of the component but with your
tip and thinking about it, it makes sense.
Actually I needed to use:
setText(t_label.getText());
Using toString got me: "java.swing......" (the components text representation)
Thanks a bunch!
/Steve

No volume available in RMAN-default family

Similar Messages

Maybe you are looking for