Number of logical interface

Hi all,
How can i programatically get the total number of logical interfaces that are added to a particular interface ???
thanks,
rakesh

Hi,
Yes i am talking about the Logical interface. Considering that my n/w interface is "le0", i want to programatically determine what are the locial interfaces that are attached to it (i.e le0:1, le0:5.....etc)
thanks,
rakesh

Similar Messages

Logical interface in solaris 10

Hi there,
I need to configure logical interface in a solaris 10 3/05 server. After reading the Solaris 10 IP services manual, I am not quite sure what to do. All the examples and explanation are about using the new subcommand addif of ifconfig. It was not clear in the documentation if the setting logical interfaces via addif will persist across boot.
Can one still configure logical interface in Solaris 10 in a more traditional way like in Solaris 8? In an Solaris 8 server I will do the following.
Let's assume I want to configure in a solaris 8 server a logical interface named hme0:1 with IP address 192.168.20.28 with netmask 255.255.255.0 for hostname host001
# cat /etc/hostname.hme0:1
host001
^D
# echo "192.168.20.28 host001" >> /etc/inet/hosts
# echo "192.168.20.0 255.255.255.0" >> /etc/inet/netmasks
# reboot -- -r
Can one still do that in solaris 10 3/05 server?

Hi there,
I need to configure logical interface in a solaris 10
3/05 server. After reading the Solaris 10 IP services
manual, I am not quite sure what to do. All the
examples and explanation are about using the new
subcommand addif of ifconfig. It was not clear in the
documentation if the setting logical interfaces via
addif will persist across boot.No. No 'ifconfig' command is persistent.
Can one still configure logical interface in Solaris
10 in a more traditional way like in Solaris 8? In an
Solaris 8 server I will do the following.
Let's assume I want to configure in a solaris 8
server a logical interface named hme0:1 with IP
address 192.168.20.28 with netmask 255.255.255.0 for
hostname host001
# cat /etc/hostname.hme0:1
host001
^D
# echo "192.168.20.28 host001" >> /etc/inet/hosts
# echo "192.168.20.0 255.255.255.0" >>
/etc/inet/netmasks
# reboot -- -r
Can one still do that in solaris 10 3/05 server?Absolutely.
You don't need to reboot (you can run ifconfig for this boot and let the files do the work next time) and the -r doesn't do anything with interfaces (expecially virtual interfaces) anyway.
Darren

My serial number for Logic Studio doesn't work. I used one from a different box and it worked. How can I get a new number?

My serial number for Logic Studio doesn't work. I used one from a different box and it worked. How can I get a new number?

http://support.apple.com/kb/TS2005
http://support.apple.com/kb/HT1861
https://ssl.apple.com/support/proapps/serialnumbers/

Increasing maximum number of Logical Processors in a Processor Group greater than the default (64)

Can the maximum number of Logical Processors allowed in a Processor Group be increased by Bcdedit command or registry key to a number greater than the default (64) to allow non-group-aware applications to seamlessly scale via multithreading across more cores
MSDN documents methods to reduce the max number of LP's in a Processor Group to 1 or any power of 2 less than 64 in order to increase the number of Processor Groups. But there is no discussion of how to increase the maximum number of Logical Processors
allowed in a Processor Group to a number greater than the default (64), e.g. to 128 or 256.
Since a non-group-aware application/process can only run on 1 Processor Group, increasing this limit is needed to allow non-group-aware multithreaded applications to scale seamlessly for parallel computation across more than 64 cores simultaneously on systems
with more than 64 cores (for example, a quad-socket Intel Xeon system with 24 cores per socket, including true and hyper cores). If that limit can be set via registry key or command line, or if there is another way to force all the cores on
all 4 sockets (4 NUMA nodes in this case) to join in 1 Processor Group, then non-group-aware applications will not need to be rewritten using group-aware thread-affinity APIs.

Hi John,
Are you trying to specify a static NUMA-node-to-group assignment, rather than letting Windows dynamically assign NUMA nodes to groups at boot time? If yes, You can refer the
following related KB:
How to manually configure K-Group assignment on multiprocessor machines
http://support.microsoft.com/kb/2506384
Systems with fewer than 64 logical processors always have a single group, Group 0. On systems with 64 or fewer processors, existing applications will operate correctly without
modification. Applications that do not call any functions that use processor affinity masks or processor numbers will operate correctly on all systems, regardless of the number of processors. To operate correctly on systems with more than 64 logical processors,
the following kinds of applications might require modification:
•Applications that manage, maintain, or display per-processor information for the entire system must be modified to support more than 64 logical processors. An example of
such an application is Windows Task Manager, which displays the workload of each processor in the system.
•Applications for which performance is critical and that can scale efficiently beyond 64 logical processors must be modified to run on such systems. For example, database
applications might benefit from modifications.
•If an application uses a DLL that has per-processor data structures, and the DLL has not been modified to support more than 64 logical processors, all threads in the application
that call functions exported by the DLL must be assigned to the same group.
By design, a non-NUMA computer is considered to have one NUMA node. Because NUMA nodes cannot span groups, the system creates a node for each group after you restart the computer.
The related KB:
Processor Groups
http://msdn.microsoft.com/en-us/library/windows/desktop/dd405503(v=vs.85).aspx
More information:
Uneven Windows Processor Groups
http://blogs.msdn.com/b/saponsqlserver/archive/2011/10/08/uneven-windows-processor-groups.aspx
Boot Parameters to Test Drivers for Multiple Processor Group Support
http://msdn.microsoft.com/en-us/library/windows/hardware/ff542298(v=vs.85).aspx
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Where can I find the serial number for LOGIC PRO from the AppStore

Please help me:
Where can I find the serial number for LOGIC PRO from the AppStore?
I bought and downloaded the application, now it asks me for the serial number but I didn't not receive it or can find it.

My understanding is that if it was purchased throught the App Store, then there is no requirement for a serial number. At which point does it ask you for the serial?

HOW DO I GET A SERIAL NUMBER FOR LOGIC PRO IF LOST MINE ?

How do i get a serial number for logic pro ? i purchased it so long ago and i just cleaned off my computer and re-installed mountain lion . When i did an erase and archive i forgot to look to see the serial number . Now when i go to launch it it asks for SN . Any help would be great .

http://support.apple.com/kb/ht1861

Solaris 10 ip address of outgoing packets on logical interfaces

Hi there.
I have a Sun here with Solaris 10 and one physical interface e0 and one logical interface on it e0:1.
e0 has address 1.2.3.4
e0:1 has address 1.2.3.5
gateway is 1.2.3.254
To every ip address I bind a sendmail deamon.
For incoming connection the ip packtes come out with the right ip address
from the interface to which the connection was established.
But for outgoing packets it seems that only the ip address of e0 is used even if the sendmail on e0:1 makes an outgoing connection.
On Solaris 9 every app that binds to an logigical interface uses that ip for outgoing connection, but on Solaris 10 it looks, that only the ip address of the primary (physical) interface (e0) is used.
Is there a way to make outgoing connections of apps binding e0:1 to use the ip address of the e0:1 interface?
I dont use zones, both interfaces are in the global zone.

I'm not that familiar with postfix, but thats where the solution should be. As I mentioned earlier in this thread, the application has full control here and should be the place to set it. I'll bet postfix has a setting for what outbound IP address to use.
Trying to coerce this at the OS level is much more difficult.
Especially with your phrase about "if packet enters..." There's two possible things you might mean by that.
#1 is if the packet coming in starts a TCP session. That session sets the two IP addresses, and the OS can't override that address for outbound packets. The usesrc setting is only valid for TCP sessions started by your machine.
#2 is if the "packet coming in" you refer to really means an email in (which gets completed), and then your machine sends an email back out. But then there's no association (in the OS) between the two emails, so it doesn't know that this mail "should" go out that interface.
In both cases, I think you'll want postfix to handle this.
Darren

Need assistance in creating a logical interface in PIX 7.2

Hi,
I've recently upgraded my pix 525 from 6.3 to 7.2. Now I need to take a spare interface (ethernet4) enable this interface and create sub interfaces to use to communicate to my inside network by mapping to inside vlans.
In 6.3, I would do the following (example)
niterface ethernet4 vlan240 logical
nameif vlan240 PROD security 25
ip address PROD 192.168.1.2 255.255.255.0
Now that the 7.2 command set is really different and I do not have a test PIX to test with, I'm hoping that someone would have an example for me.
Goal: My remote location (VPN/GRE) needs to communicate to my local networlk. But, I am not advertising this subnet in ospf. I want to map an advertised IP to this inside non-advertised IP. Setting up a logical interface is how I can achieve this.
Please advise with samples.
Regards
jeff

Hi,
I think this will help :-
http://www.cisco.com/univercd/cc/td/doc/product/multisec/asa_sw/v_7_2/conf_gd/general/intrface.htm#wp1044006
Regards,
Vivek

-6.1db..........a magic number in logic?

hi, i find i use/choose this number in logic a lot.
-6.1db is to absolute peak i'll let any recorded trk to be rendered at.
-6.1db is rarely exceeded on any fader anywhere.
-6.1db is where i set the peak limit of a compression/limiting plug 90% of the time.
-6.1 to -18db is the range my faders move in the most.
-6.1 to 0db is the attenuation range i set most plugs to if they feature an input trim.
just above -6.1db (5.9) is where the peak in Wave Burner set as standard for burning cds. (i'll go to just under 0db for clients).
the numbers: -6.1, -12, -18, and even -24db are basic level settings/ranges
used in most of my mixing.
Magic number?
david r.

G'day, mate, these steps, i'll use as rough start
points to get a mix going, then i'll home in on fine
tuning down to +- 1.5db, and sometimes smaller.
i'm finding that my mix levels are more consistant
and predictable like this.
and with clients it reduces time/money.
i even have preset on the gain plug at these values.
it's getting to the point where i know the outcome of
a render without having to look at the resulting
file.
it is also invaluable training for one's ear to be
able to resolve minute change in level.
cheers, david r.
Well I do not believe in "magic" anything when it comes to audio but I think it is a very sensible approach to use a universal detente point and 6.1 sounds fine to me.

TA23387 i cant find my serial number to logic pro 9 to activate i got a new computer

i can find my serial number to logic pro to activate on my new computer

If you bought the Boxed version of Logic then you have two basic choices....
1) If you still have your old comoputer and Logic Studio 2/Logic Pro 9 is installed on it.. Open up Logic and go to the Logic Pro menu option and choose About Logic and you will find your serial there (Assuming you bought the full version of Logic 9 DVD) If you bought the upgrade version of Logic Pro 9 then you will also need your Logic 8 serial as well..... which can be obtained the same way if you retained the original copy of Logic 8 on your old Mac.
2) Use the following form to contact Apple get issued a replacement serial for Logic Pro 9
https://ssl.apple.com/support/proapps/serialnumbers/
If you bought your full version of Logic 9 from the App Store you don't need a serial (as it uses your existing Apple ID and Password to authenticate) and can simply open the App Store App on your new Mac, navigate to the purchased tab and redownload Logic 9 from there.

Zone with multiple logical interfaces

Hi,
How can multiple logical network interfaces be added to a running zone?
I have configured and installed a whole root zone with one shared-ip network interface.
Now, I need to add more logical interfaces to the same zone.
On a physical server with a bge interface, I would create a /etc/hostname file for each logical interface such as
$ ls /etc | grep host
hostname.bge0
hostname.bge0:1
hostname.bge0:2
hostname.bge0:3
hostname.bge0:4
hostname.bge1
hostname.bge1:1
hostname.bge1:2
hostname.bge1:3
hostname.bge3
hosts
$How can the above be done for a zone?

Hi
This requires 2 steps. Firstly update your zone configuration to add the logical interface and its associated IP address.
Assuming from below you want the logical interface to be added to bge0 then do the following replacing the zonename and ip address for whatever is appropriate for you.
# zonecfg -z itchyzone
zonecfg:itchyzone1> add net
zonecfg:itchyzone1:net> set address=192.168.1.21
zonecfg:itchyzone1:net> set physical=bge0
zonecfg:itchyzone1:net> end
zonecfg:itchyzone1> exitYou can do the above as many times as you like to create multiple logical interfaces for the zone.
After doing the above you will need to reboot the zone to get the new logical interface.
However if you cant reboot the zone you can plumb a logical interface into the zone by running something similar to the following (change for your zonename, IP etc) from the global zone:
# ifconfig bge0 addif 192.168.1.21 netmask + broadcast + zone itchyzone1 upyou will now have an extra interface in the zone (in this case called itchyzone1). To verify, login to the zone and run ifconfig -a and you will see your new interface.
# zlogin itchyzone1
[Connected to zone 'itchyzone1' pts/4]
Last login: Mon Oct 5 22:24:15 on pts/4
Sun Microsystems Inc.   SunOS 5.10      Generic January 2005
# ifconfig -a
lo0:1: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
        inet 127.0.0.1 netmask ff000000
bge0:2: flags=201000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 2
        inet 192.168.1.20 netmask ffffff00 broadcast 192.168.1.255
bge0:3: flags=201000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,CoS> mtu 1500 index 2
        inet 192.168.1.21 netmask ffffff00 broadcast 192.168.1.255Hope this helps
Martin

Assigning Port Number to Logical System.

Hi,
How can i assign Port Number to Logical System.
i have created Port Number but Logical System which i am looking is taking another (Default) Port, how do i change it.

this might help:
http://help.sap.com/erp2005_ehp_03/helpdata/EN/92/7d9601fb90ae41b14154e1f9e0cc58/frameset.htm

HT4812 I recently fixed my computer and need to reinstall logic pro 9 but I can't find the booklet with my serial number, is there any other way I can get the serial number for logic pro 9 (box)?

I recently fixed my computer and need to reinstall logic pro 9 but I can't find the booklet with my serial number, is there any other way I can get the serial number for logic pro 9 (box)?

If you still have the receipt or other proof of purchase, you can ask Apple to send you the serial. Otherwise, bad luck mate.. Good news is, you can now buy Logic Pro 9 from App Store for just 199 USD

Serial Number for Logic Pro 8

Hi
Can anyone tell me where I can find my serial number for Logic Pro 8 please?

in the box you bought
there is a 2 page booklet there with the serial

How to detect the number of logical processors?

Hi,
How to detect Hyper-Thread Technology, the number of processor cores on a single package, and the number of logical processor?
What java api can do this?
Thanks for help!

Who can help me?

Number of logical interface

Similar Messages

Maybe you are looking for