OUTPUT to HD Monitor

Hi all....
I've got a G5 2.5 with 2.5mb RAM running 10.4.5 with all my Pro Apps up to date. A Blackmagic Decklink Pro out to a 23" Sony Monitor by way of an HD to DVI converter.
I have the VIDEO OUTPUT in the prefs set to Blackmagic Video Output - DVCPro HD 720p 60 (same as source material and the proj settings in Motion)
Every other pro app does fine with this setting (FCP 5.0.4, AE 7) but Motion (2.0.1) will not sent the signal to the Monitor.
I know there was an issue with it not working properly if I was running FCP at the same time (in the past. was that fixed?) So I run MOTION alone without having any other apps running and still NO GO.
Any Ideas or fixes?

Patrick:
I'm running 10.4.4 on the G5 that has the Decklink card in it but i'm in the middle of a fairly big project and was avoiding the upgrade til later. I'm finding more and more though, that I need video assist while using MOTION.
By the way, and on another subject, I'm doing HD blue / green sceen pulls and I was wondering what app you think works best. Shake is a dog to learn and the workflow is tedious. Primatte in Motion has very few options ( as opposed to the Shake version ) AE maybe?

Similar Messages

Dell Venue 11 Pro Tablet Docking Station - Dock Firmware won't update or output to any monitor

Hi,
Just bought a Dell Venue 11 Pro Tablet Docking Station and it won't output to any monitor via HDMI or Displayport.
I've tried updating the firmware to V02 and V03. I get the message:
Current On-Board Firmware is 0.41.9
Do you want to update with firmware version 0.41.23 (V03) 0.41.19 (V02)
When I select yes I get the following error:
Error: Please unplug the power connector from the Dell desktop dock for 15 seconds, then plug the power connector back into the Dell desktop dock and try again.
This I keep repeating but it will not update.
The model number of the dock is: K10A001.
The only other thing I notice is that the power adapter does not appear the same as any of the pictures I have seen and is a Dell 74VT4 (65w) which seems be for a Dell XPS 18 (1810).
Please help as I think this may need to be sent back.
Thanks.

Hello,
I've exactly the same problem. I've also the model number K10A001 and the current Firmware 0.41.9, and it is also not possible for me to flash the docking station.
This is also problematic because only one monitor of the two connected monitors works. An this monitor shows only a picture, if it is plugged, after the dockingstation and the Venue 11 Pro has been started.
I think there is maybe an improved flash utility required in order to allow to flash the docking station? If some one had succeeded please respond.
Thank you

No output to NTSC monitor

I am unable to get Encore 2.0 to output the Menu Editor to my NTSC monitor. In Preferences > Audio/Video Out I have checked the "Show Menu Editor on DV Hardware" box and Encore correctly recognizes my Sony device and indicates that it is in "VCR Mode", however, no picture is displayed.
I have no problem getting video out to the monitor from any of the other Production Studio Premium applications.
FYI - Although I wouldnt expect it to have any bearing on this problem, the tryout version of Encore 2.0 was installed on this computer before purchasing the Production Studio.
Any ideas on what I may be missing?
Thanks for your assistance

Ok - answering my own question - I unchecked "Automatic" - restarted Encore and am now able to have output to the monitor as expected.

How do I output the program monitor from Premiere Elements 13 to an external TV monitor?

I can find information about dual monitor set ups, but is it possible to output the program monitor only to an external monitor?
If so, what is needed?
I'm using PE`3 on a PC with Windows 7 64 bit with an NVIDIA Quadro NVS 290.
Thanks

bobj
Have not found a way, but....
Do you have a HDMI cable and does your computer and TV each have a HDMI port.
The TImeline panel appears to be the only undockable panel in the Premiere Elements 13/13.1 Expert workspace area (Window Menu/Dual Monitor)
The best I can do is to make a HDMI connection between the HDMI ports of my computer and TV, with display at Duplicate or Extend. That does not appear to be what you seek.
The other part of all this is that Premiere Elements used to have a "Playback Settings" in Project Settings and accessed from
right clicking the Edit area monitor. That is no longer to be found in 13.1, even in a grayed out state. And, for me, the Playback Settings could not be made visible
when attaching a 3rd party device.
In the days of Premiere Elements 11, the answer to your question might have been as described in the following
Adobe Premiere Elements 11 * Previewing movies
Until proven otherwise, I am thinking that it cannot be done in Premiere Elements 13/13.1. But, I am not at a stage where I would put a never and always stamp on this.
ATR

Hetis 865GV video output to two monitors

Does anyone know how to set the Hetis 865GV to output simultaneously to the VGA port and to either DVI or S-Video to display the same output on two monitors?

well i dont have an 865 , but that is handled by my video card.
try reading up in the features of that, using a short alt f something key to turn on 2nd display. may have to set it up under video card propertes, an click a check box under tv.

Is it possible to output to div monitor and s-video at the same time?

I'm editing video and want to see the broadcast results on the fly (ie monitor and tv side by side, same image onscreen). Is it possible to output to div monitor and s-video at the same time? Maybe thru a splitter cable. I'm concerned about resolution issues.

This is not possible with a mini.

Satellite Pro U300: DVD issue - error: cannot output to external monitor

Hi,
I was having problems playing a dvd on my U300.
Basically the software would load but when I tried to play the dvd it said "cannot output to external monitor".
Having gone through all options I could not find anything to stop this happening. I then downloaded the latest software from the toshiba site.
dvdpl-20070807102909.zip
I resintalled this but got the same error message.
I then uninstalled the software and tried to reinstall but now it just produces an error mesaage saying it cannot intsall the software on this computer.
How can I reinstall this?
Regards,
Mark

I presume you have received the Toshiba Recovery CD. Am I right?
On this CD you can find the Toshiba image file. This image contains the Vista OS, Toshiba drivers, tools and additional software.
But note; you cannot install only a single program. To reinstall a application from the Recovery CD you have to format the HDD and have to reinstall the whole OS using the Recovery CD.
As Gipsyman said, the Toshiba driver page contains update and the original preinstalled software is needed.

[SOLVED] NVidia, Xorg, Output not reaching monitor?

Hardware...
====================================================
Computer: ASUS K55VD Laptop (UEFI Motherboard)
Processor: Intel i5
Graphics: NVidia GeForce 610M, also the Intel chip that I'm not using (I think)
Relevant System Information (I figure maybe the location of my initramfs is messing with driver installation?)...
====================================================
Partitioning...
sda1: /boot (FAT32)
sda2: / (ext4)
sda3: /home (ext4)
Boot: Syslinux EFI setup using efibootmgr (ESP: /boot, Syslinux: /boot/EFI/syslinux)
Driver package: "nvidia", corresponding libgl and lib32 stuff. NOTE: I know this is the wrong version, but my problem is _exactly_ the same with nvidia-304xx.
Xorg Configuration (no other conf files influencing outcome, no ~/.xinitrc)...
/etc/X11/xorg.conf.d/10-evdev.conf
/etc/X11/xorg.conf.d/10-quirks.conf
/etc/X11/xorg.conf.d/10-server.conf
/etc/X11/xorg.conf.d/20-nvidia.conf
Other Notes: The laptop originally came with Windows 8. At the time, I didn't want to spend a whole lot of time installing Arch, so I chose Ubuntu for the time being. While Ubuntu was installed, I noticed that the driver being used was called "Mesa", and certain applications didn't like that (NCAR's VAPOR, for example). Perhaps there's a problem with the hardware that's causing Ubuntu to choose an alternate install system, and now I'm running into that?
Problem...
====================================================
I've set everything up properly according to the Beginner's Guide, NVIDIA and Xorg pages.
I run startx.
At "Loading extension GLX", the whole TTY freezes (stops redrawing, can tell because cursor freezes in current state <on/off>).
At this point, I can still switch TTYs with C-M-F<n>, so it's just that one TTY.
I can type "exit", <Enter>, and then the server dies dramatically.
Here's the full output from the server, which had to be unjumbled by redirecting all output to a file
Here's my /var/log/Xorg.0.log, recovered after the test
I was even able to retrieve this glxinfo output by piping to a file!
Again, I was typing blind, so there's no real guarantee that the glxinfo output is, in fact, glxinfo output...
Analysis...
====================================================
I have no idea what the problem is on the server's shutdown, but I've got ideas about the rest of it.
I figure what's happening is that the server is starting just fine, but it isn't putting output on my monitor. It opens the twm environment, which starts with an open terminal. When I type "exit", <Enter>, the server shuts down again, as expected, but something goes wrong.
That's how it occurred to me to grab that glxinfo: 'glxinfo > ~/test'
Does the following mean that it's actually using the Intel graphics? (found this in Xorg log)
[ 1571.248] (--) PCI:*(0:0:2:0) :::this refers to the Intel graphics
[ 1571.248] (--) PCI: (0:1:0:0) :::this refers to the 610M
What does that asterisk (*) mean?
Does this line mean that my graphics card isn't hooked up to my monitor?
[ 1571.383] (--) NVIDIA(0): Valid display device(s) on GeForce 610M at PCI:1:0:0
[ 1571.383] (--) NVIDIA(0): none
Maybe I need to configure my monitor to be detected somehow?
I noticed two errors in the Xorg log that might be related...
[ 1571.385] (EE) NVIDIA(0): Failed to initiate mode change.
[ 1571.385] (EE) NVIDIA(0): Failed to complete mode change
Maybe there's a simple package installation that will fix everything?
If there's any more information you need, please ask.
Thanks!
PS: wgetpaste was EXTREMELY helpful!
Last edited by soccermiles (2013-12-22 23:23:40)

New Progress!
I've managed to get my screen to go black during the server's run, instead of having my TTY just freeze!
I followed the instructions here
However, now I have the problem that the X server shuts down about two seconds after startup. I have confirmed that both of the xrandr commands are completed.
Here is my x log
Here is my x output
As you can see, we have "Screen 1 deleted because of no matching config section". I have no idea what that means.
The NVIDIA driver still appears to try setting mode "NULL" (maybe it isn't getting the available modes properly?)
At the end, there's this weird thing...
reporting 3 4 17 122
have a master to look out for
adjust shatters 0 1366
need to create shared pixmap 1(II) NVIDIA(GPU-0): Deleting GPU-0
Uhhh...why is it deleting my GPU? (I have no idea what it means by that)
UPDATE (again!)...
I HAVE LWM WINDOWS APPEARING! (but I had to stop the nvidia to get that)
I changed the ServerLayout to have Screen 0 be the "intel" screen.
Initially, input wasn't being handled at all, resulting in complete inability to do anything once x started
I managed to get input working by adding some xorg configs for my input devices (now I have fully-functional xorg, but without my nvidia card)
I still want to get my nvidia working.
Last edited by soccermiles (2013-12-22 19:31:50)

Video Output to NTSC monitor

I recently got new furniture, so of course, I unhooked everything and moved it around, and now, for some reason, I can't see video on my NTSC monitor. I know everything is hooked up correctly because I can log and capture and see video on the monitor; the video captures correctly with audio and everything. But when watching video in the timeline, there's nothing happening on the monitor. Any suggestions? Has this happened to anyone else?
I have switched out firewire cables, rebooted the computer, etc. I'm so confused!

#8 External Monitor Viewing.
Shane's Stock Answer #8:
A simple path is mac > firewire > camera or deck > rca cables > tv
Then start up your camera and tv, then open fcp.
Then go View > External video > all frames
Video playback should be Apple firewire NTSC (If you are using an NTSC set)
Audio playback should be Audio follows Video
Techinially, this should send synched video to your TV
If for some reason you can't view your timeline on your external monitor, there are a few things to try:
1) Make sure that the camera/deck is connected and powered on BEFORE you open FCP.
2) In the Final Cut Pro menu select AUDIO/VIDEO Preferences and make sure your signal is being sent out thru Firewire DV.
3) Go to the menu and select VIEW>EXTERNAL>ALL FRAMES.
4) Click in the % box above the image and select FIT TO WINDOW.
5) Go to VIEW->refresh A/V devices
6) Make sure the Log & Capture window is closed
If you want it to play in both the canvas and the external monitor you need to go to the FINAL CUT PRO menu and select AUDIO/VIDIO settings and make sure MIRROR ON DESKTOP is selected under the PLAYBACK OUTPUT section
Shane

Viewer won't output to NTSC monitor in FCP5.1

Hello!
I was used to being able to view my clips in the viewer on my ntsc monitor in HD, since upgrading to FCPStudio5.1.1, I can't seem to find an option for this, the manual mentions none, and a search provided no answer related to the viewer. I am able to watch the timeline just fine on my ntsc monitor.
Is this a new change with FCP5?
Thanks!
Ymir

I am connected to a Sony mediaconverter via firewire.
It connects to my tv monitor. External video is set to all frames. After refreshing a/v devices, the viewer will now output to the screen when using "gang" setting. If I use sync off, I get current frame its stopped on. Open gives nothing. Is there a way to make gang the default so I don't have to set it for each clip?
Thanks
Ymir

No 1920x1080 output to external monitor from MBP 2011 OSX 10.6.8

Hi, I have a MBP 2011 running OSX 10.6.8.
I have recently purchased an Asus ML249H Monitor and the Kanex Mini DisplayPort to HDMI Cable 10 ft (3 m) MDPHD10FT.
The monitor should display at 1920x1080 natively but does not. The MBP max output resolution is 1600x900 on this screen. Is this a known issue with the MDPHD10FT cable or is it OSX? What it the work around to get 1920x1080.
Thanks

i had to go into iCal Preferences and delete my account and then put it back in. Everything is working fine, now.

Video Output to TV Monitor

Hi
I have a Miglia directors cut and am trying to output my floating movie onto a tv monitor. Following intructions from the manual I go to song settings and change the video output from Window to FireWire. Doesn't work. It seems as if logic isn't seeing the Firewire. The Miglia works well for outputting video in Final Cut Pro, where the app. has a 'refresh a/v devices' option which kick starts the Miglia. Does logic have anything like this?
Any help would be appreciated.
ta

I use a dc30 personally, brilliant old card.
I reckon it may be a diveo format problem. play the QT video in Quicktime. does it play back on the TV? if it does then it should play back in logic no problem. if it doesn't, then you might need to convert the video to dv streaming (which is different to dv which final cut pro uses). i am no expert in this area, but until somebody more knowledgable posts then i would say QT format issue is your problem.

FCP Problem with Firewire output to external monitor and speaker ???Help

i have a g5 powermac. the problem is when using Final cut pro 4hd. when i output my work through firewire to my external monitor and speaker i have a problem with the audio signal. Theres feedback/noise/hiss from the speakers. The firewire connects to DSR-11 vtr deck which feeds my monitor and speakers. it only happens when in FCP is set to A/V firewire output. does not happen if Video output is not set to firewire.
I Diagnosis is that it is not my dsr-11 deck or firewire i've ruled those out. The problem is either FCP software or Hardware problem with my G5
Does anyone have a similar problem. please respone, i will try to answer any respones,
Thanks
powermac g5 powermac

CaptM
From the firewire that feeds the dsr-11. on the output, i use s-video cable to my monitor (sony pvm-14l) and High Quality rca cables thet feed the audio to the Roland Speakers.
I've changed all wires and still have audio problem. I,ve changed my Dsr-11 deck to my camcorder and still have the problem.
If any of u guys use FCP The problem happens When I select view> external Monitor > and select firewire for Audio/ and video. I have never changed my editing habits, something just went wrong with the signal, I think its a Hardware problem with the firewire connection. I'm Going to have to bring this to a Apple Service Center In my local area one day.

FCP DV Output to External Monitor Quality Problem

Hi there, I'm using Final Cut Pro HD from Final Cut Studio 2, and I'm having a problem with the quality of the image on my external monitor. I have checked all the settings etc... for external video and they all seem right, but when I play the video in my canvas the signal into my camera lcd and onto my ntsc monitor is not correct. It plays the video; however, it also has a constant stream of large grey squares flashing across the TV. I would say 50% of the output signal is my video, and then 50% of the screen is taken up by these large moving grey squares.
I have all my windows fit to screen, I've choosen the Apple FireWire NTSC option in the A/V settings, and I have the all frames checked in the View tab.
It seems like only half of the signal is making it's way from FCP to my camcorder. At first I thought it was my NTSC monitor, but when I saw that the grey squares are also showing up in my camcorder's lcd screen I figured that it must be a problem coming from FCP.
Any help with this would be greatly appreciated. Thanks so much!

You'd think so, but I'd try another anyway...
Another thing that might be amiss is the power management on your Mac. There is a PMU button on the motherboard of your machine you can reset. You need to unplug it from power first however. It's under the fan you can remove to add RAM...
Jerry

Timeline output to external monitor

Hi - I'd like to see the timeline output on an external monitor (TV set with composite in) while editing. I'm told the only way to do this is to purchase an input-output card and one of the most reasonably priced ones seems to be the Pinnacle Movie Box. Does anyone know if this compatible with Premiere Pro CS3? Will it do what I want it to? If not, what is the best solution?
Thanks in advance...

For the moment, neither SD nor HD, but just simple DV :) But I'd like to buy something that can handle HDV, as I'll be editing a project soon. The output need not be great - after all, it's going to an ordinary TV set, not a precision reference monitor. The purpose of this additional monitor is to screen unfinished portions of the film to other people. I might have people come in to give their comments during the editing, so it's useful to be able to output the timeline.
Pinnacle lists four products on their site: Studio MovieBox Plus, Studio MovieBox Ultimate, Studio MovieBoard and Studio MovieBoard Ultimate. Do they all work? Which of them would you recommend? Or would you suggest someting else altogether?
Thanks very much.

OUTPUT to HD Monitor

Similar Messages

Maybe you are looking for