OVM 3.0.3 - cannot add new server to VLAN group with bonded VLANs

I have a new OVS 3.0.3 server built with 2 bonded interfaces and a single VLAN running on top for the management interface. It gets discovered fine by OVM Manager (I'm running Version: 3.0.3.126, Build: 20111214_126)
I am trying to add it to a VLAN group with two VLANs -- the existing management VLAN (ID=300) plus one other (ID=301). (I already have one identical server assigned to the VLAN group, with both VLAN interfaces configured and running fine.) This works OK, and I can see VLAN 301 for the new server in Oracle VM Manager with no IP address assigned to it.
However, when I try to apply an IP address to the VLAN (via Hardware / Resources / VLAN Groups / Edit VLAN Group / Configure IP Addresses / VLAN Interfaces) it fails with this error:
Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: dispatch to server: whyovmprd02 failed. OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/1 ovs_br_config start 0004fb0010be2df bond0.301, Status: org.apache.xmlrpc.XmlRpcException: exceptions.RuntimeError:Command ['/etc/xen/scripts/ovs-network-bridge', 'start', 'bridge=0004fb0010be2df', 'netdev=bond0.301'] failed (1): stderr: ovs-network-bridge Start: No such device bond0.301
Oracle VM Manager seems to be expecting the subinterface for VLAN 301 to exist on the server already - which it doesn't of course, because the server has just been built, so it only has its management interface VLAN in place (VLAN ID 300)
I have managed to work around this by removing VLAN segment 301 from the VLAN group completely, then adding it back in with the IP addresses for both servers in place. This seems to convince Oracle VM Manager that it needs to create the bond0.301 subinterface before it configures it. However, I obviously had to shut down all VMs to do this, and it was really messy as VLAN 301 is the storage network, so my original server lost contact with the NFS storage for a while which caused it to fence etc.
There must be another way??! Any pointers would be very much appreciated.

Avi Miller wrote:
It's fixed in 3.1. In the meantime, if you can remove and reapply the Virtual Machine role on that network, it'll recreate the bridges for you.Thanks for replying Avi. (I won't ask you for a release date for 3.1 :))
I did try that initially, but it didn't seem to help - I got this error back:
Job Internal Error (Operation)com.oracle.ovm.mgr.api.exception.FailedOperationException: OVMAPI_4010E Attempt to send command: dispatch to server: whyovmprd02 failed. OVMAPI_4004E Server Failed Command: dispatch https://?uname?:[email protected]:8899/api/1 ovs_if_meta bond0.301 ethernet:0004fb00100a35f{why-be-301}:STORAGE, Status: org.apache.xmlrpc.XmlRpcException: exceptions.Exception:ovs_set_metadata: interface /sys/class/net/bond0.301 does not exists
This appears to be from ovs_if_meta in /opt/ovs-agent-3.0/OVSVMNetConfig.py, which looks to be where the agent tries to write out the new roles for the network into the metadata file - it seems to be expecting the VLAN to exist already, and specifically checks in /sys to make sure that it is there.
Should / could I add a step to my kickstart build to force the 301 VLAN to be created maybe? This would bring it into line with the other VLAN that is used for management, which is of course sitting there ready and waiting as soon as the server is built.

Similar Messages

Cannot add new items to a value list in AW database

I have a database which I have been using for many years. One of the fields is a value list. I just went to add another item to the list, and no matter what I do, the Create button is grayed out. I have another value list in the same database that works fine.
There are currently 170 items in the value list that is causin the problem, but I didn't think that there was a limit to the number of items that can be is a value list. (At least there is nothing in the AW technical specifications to indicate thin. I duplicated the existing database, deleted about 20 items from the list, then saved the file, and reopened it, and still cannot add new items to that value list. Does anyone know what might be causing the problem?

Oops
I read too fast.
Here is a short script which may help.
Replace the pop-up item by a text one and edit the property myList in my script to fit your needs.
Select the field to fill and run the script.
Then choose an item in the displaid list. It will be pasted in the selected field.
This trick would give you to work with a "no limit" list of items.
-- [SCRIPT DB fillFieldFromAlist ]
Assuming that
the front document is a database one
and that a text field is selected,
run the script to select an item in a list
and paste it in the field.
Yvan KOENIG, Vallauris (FRANCE)
le 19 mars 2007
property MyList : {"item 1", ¬
"item 2", ¬
"item 3", ¬
"item 4", ¬
"item 5", ¬
"item 6", ¬
"item 7", ¬
"item 8", ¬
(* edit the list to fit your needs *)
tell application "AppleWorks 6"
activate
tell document 1
set laClasse to (get class of selection)
if laClasse is not field then return (* the selection is not a field *)
set myItem to choose from list MyList
if myItem is false then return
set the clipboard to myItem's item 1
select menu item 7 of menu 3 (*
Tout sélectionner •• Select All *)
paste
end tell -- document 1
end tell -- AppleWorks
-- [/SCRIPT]
Yvan KOENIG (from FRANCE lundi 19 mars 2007 16:44:53)

IPhon 4: After recently updating to version 7.1.2, all my past calendar entries disappeared and I cannot add new entries.

After recently updating to 7.1.2, all of my past calendar entries for 22014 disappeared and I cannot add new entries??

What account were you using to sync your Calendar? Make sure that account is added to the device, and make sure that Calendars is turned on for that account.
Then, go to Settings > Mail, Contacts, Calendars, and make sure that under the Calendar section that 'Sync' is set to 'All Events'.
Then go to the Calendar app, go to Calendars, and make sure that you have that account enabled.
Then, close out all the running apps on your device, and restart it.
Open up your Calendar app. Are your entries back?

Cannot Add New Form Fields

I'm troubleshooting a problem with an existing pdf document in our office. Though I install Acrobat I do not use it on a daily- hence my asking for assistance. The computer is an Optiplex 745 running WIN XP Pro SP 2 with all updates.
The doc is a 42 page human resources document that has both scanned and original (made in Word/Acrobat) pages. Though I can edit existing fields/boxes, I cannot add new ones. I can select "add fields", click and drag seeing the crosshairs and field/box area, but when I let go, nothing happens. No new field and no erorr messages.
I've checked the security- it's wide open (no security) and layers- it has none or only one. The user who reported the problem is using Acrobat 5.x, I've tested it in 5.x, and 9 (standard and pro) on my computer with no success. I've included screenshots of the doc info below in hopes that they might provide some clues as to the problem.
Thank you for any assistance that you may provide.

After discovering that the other primary user had a local copy of this form- I tried that in Acrobat 9 and it was editable. So it appears that it was the form itself.
I'm resaving the local document to the network drive (where the problem doc came from) and updating both primary users to Acrobat 9. One was using 5 the other 7. Hopefully that will prevent any further problems.
Thanks for your assistance.

Cannot Add new line using BI IP query

Hi All,
We have created a planning application (BI IP Query) and used it in VC 7.1 model using BI Query Wizard service. Now we are able to customize existing rows ( existing rows are using flat file upload)... we can able to change the existing record values and save it.
But we are not able to add new line... its going to dump... We are able to add new line using WAD with same query but not in VC 7.1
This issue is same as below 2 threads...
Re: How to create new records through a VC form in an input-ready query??
Re: Cannot add new records through VC form when consuming IP write back query?
Thanks,
PradeeP

Its working now... SAP has given the fix (patch) for this issue when we deployed it, everything is working fine... I think they will release this fix (patch)soon...
Raise an Sap OSS message for solution

Cannot add new selectors or edit existing CSS file with my Mac

I have just subscibed to Dreamweaver CC and I cannot add new selectors or edit the exisiting "main" css that comes with the tutorial. When asked to add selector a box appears but when I press enter/return twice it disappears. Also there is no option to edit existing properties. for example, to change a font color I pick color but there is no enter or "OK" option. I'm very puzzled and stuck.

The trial version of Dreamweaver is fully functional. The only limitation is that it stops working after 30 days. If you're having problems with getting the software to work correctly, it might be a good idea to try posting a question in the Downloading, Installing, Setting Up forum, mentioning the fact that you've already posted here (otherwise, they might just transfer you back to this or one of the other Dreamweaver forums).
If you can't make changes to files, it might have something to do with permissions or the user account that you've logged onto the computer with.
When asking for help in the other forum, mention your operating system, and which version you're using. The problem might be related to your computer setup.

Cannot add new contact or edit existing one

Cannot add new contact or edit existing one. TH GSM, curve 8900, OS v5.0.01067, file free none ,battery pull didn't fix the problem, applications Google maps 3.0.2, whatsapp 2.6.2177. Device even freezes when trying to add or edit . Thanks

I am having the exact same problem!! I hope we get an answer.

Iphone 4s calendar events disappeared and I cannot add new events

I have an iphone 4s with ios 7. Suddenly all events I added on my calendar disappeared and I cannot add new events. The plus sign+ is there but it is light grey and will not activate. I do not sync it with any other calendar

What account were you using to sync your Calendar? Make sure that account is added to the device, and make sure that Calendars is turned on for that account.
Then, go to Settings > Mail, Contacts, Calendars, and make sure that under the Calendar section that 'Sync' is set to 'All Events'.
Then go to the Calendar app, go to Calendars, and make sure that you have that account enabled.
Then, close out all the running apps on your device, and restart it.
Open up your Calendar app. Are your entries back?

I cannot open new tabs in Firefox, either with CTRL+T or with the mouse right click or click on the tab icon.

I cannot open new tabs in Firefox, either with CTRL+T or with the mouse right click or click on the tab icon.

I have this problem as well. I could not see the ask toolbar in firefox, yet in the add or remove programs it was installed. As soon as I uninstalled it, I could open tabs again!
Thanks guys!

Regarding : How to add a user to portal group with the help of webdynpro .

Hii ,
I am working on an application in which with the help of an action( Button) we r adding a user in Ztable in R/3 , as well as group in portal.
The user r successfully creating in Ztable but from portal side No user is assigned to Portal group.
I need coding solution for " How to add a user to portal group with help of webdynpro"
Any usefull link will also do.
Pls anyone have any solution ??
Thnks in advance.
Rewards r waiting for u .

Hi,
Use UME api to add user to portal group.
Using UME API:
https://www.sdn.sap.com/irj/scn/go/portal/prtroot/docs/library/uuid/40d562b7-1405-2a10-dfa3-b03148a9bd19
Regards,
Naga

Disks not avialable and cannot add new disks to existing pools

I have a few disks that are RAW and I want to add them to existing pools. However, only 1 disk shows up as a Primordial disk and the others do not. I cannot add these drives to a new volume and when I try to add any drive to an existing
pool, the add disk option is greyed out. I have search everywhere to resolve this but no luck.
What is interesting is one of the drives that shows available for a volume is the drive I have associated to backing up the OS on the server itself and is initialized, i.e. not RAW.

Hi,
Please try to run the following commands in PowerShell to obtain the information about disks:
Get-physicaldisk
Get-disk
In additional, the physical disk added to a storage pool must be 4GB or larger. If the space is less 4GB, the disk will not appear in the storage pool window.
For more information, please refer to the thread below:
Storage Pool in WS2012
http://social.technet.microsoft.com/Forums/windowsserver/en-US/d230ef80-8791-4eaf-84b5-a41b8f7fef10/storage-pool-in-ws2012?forum=winserver8gen
Best Regards,
Mandy
If you have any feedback on our support, please click
here .
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Can not add new server

Hi,
I install Oracle Workshop for WebLogic 10.3 on Windows Vista and I create new remote server without problem but I can not see server state.
So I delete server and try add new one. Unfortunately when new server popup window is open and I click next (to Specify a WebLogic domain directory/Specify a remote host name) I can not type connection data because all fields but Re-enter password are disabled for remote server type.
Next I try reinstall Oracle Workshop and this takes no effect.
Thanks for answer.
Peter

In new installation BEA2 I create new domain and start it. After configuring WebLogic Runtime Oracle WebLogic Server connection start to live.
Same procedure with old installation doesn't work.

Cannot Add new fields to standard QM datasource

Hi
I got this erro when I try to add new fields from LBWE.
Field ZZRFKIMG cannot be selected because of unit field VRKME -> see long text
Message no. MCEX032
Diagnosis
Field ZZRFKIMG cannot be transferred, since its unit field VRKME is either not in the communication structure, or was purposefully excluded from the selection.
Procedure
If you have chosen your own field, you must also create a user-defined unit field in the append and use it accordingly.
How can I resolve it.
thanks

Hi,
My Understanding is that if the field is available in the Pool in LBWE then no need to enhance the datasource.
In my case the field is available in LBWE though it is ZFIELD (ZZRFKLMG and ZZNETPRC).
In RSA6 I added the this unit
ZZMEINS     MEINS     UNIT                                                                           Base Unit of Measure
ZZWAERK     WAERK     CUKY                                                                           SD Document Currency
I went back to LBWE and try to add the following Zfieds (ZZRFKLMG and ZZNETPRC) and the error is same.
Now I try to add the the field directly in the append structure * ZZMC05Q02ITM* but its asking to maintain the ref table and ref field.
I added ZZMC05Q02ITM as ref table and ZZRFKLMG as ref unit and I still get errors.
I am are that if I maintain it in RSA6 then I need to write user exit in CMOD but since it is available in LBWE I want to get it from the pool.
I have tried this and there was no errors during activation
ZZRFKLMG     ZZRQE_RFKLMG     QUAN     QMFE     ZZMEINS     Notification quantity in base units
I gave the table name and Unit.
Despite adding it, I still get data even though I did not used LBWE pool.
thanks alot SUV123
Edited by: Bhat Vaidya on Oct 14, 2009 10:44 AM
Edited by: Bhat Vaidya on Oct 14, 2009 11:06 AM

User cannot add new task in a project

Hi everyone,
I've got a issue with Project Server 2013.
The situation : I create a new project then, I add some resources (which are users of the AD) and I don't add new task in this project because I want that the user creates all the task.
But when he's in the "Task" page (PWA/Tasks.aspx) and he want to add a new task (ribbon TASKS -> Add a row -> Add a new Task), the new project is not present in the drop down "Project" , if I want that the project
appears, I need to add a task with the user as a ressource.
Is there any way to automatically add the project in this list without add a task for the specific resource ?
Thanks,
Patmol

Hi Patmol6,
Please note that PWA/My task is NOT INTENDED to create tasks and assign them to resources. The process to create a project plan at project initiation and to assign resources to tasks must be done:
either in Ms Project Pro connected to your server and using enterprise resources,
or with PWA: open your project from the project center, then navigate to the schedule page, edit the schedule, create the build team, create tasks and assign resources on tasks.
"My task" page in PWA is meant to make tasks updates by team members.
Hope it clarifies the process.
Guillaume Rouyre - MBA, MCP, MCTS

Add New Server with Configtool Questions

Hello All,
We are running EP7 SP12 on W2K3 with 16GB RAM and 4 CPUs.
As part of one the Go Live checks done to the system a while back, it was recommended that we increase the number of Server processes to the instance.
So, I followed the information here (http://help.sap.com/saphelp_nw70/helpdata/en/68/dcde416fb3c417e10000000a155106/frameset.htm) to add 3 additional servers to the instance. When I restarted the J2EE engine, it basically sat there in a 'Starting Apps' status. I waited about 2 hours before I stopped the startup process. I went back into Configtool and did a 'Remove Server' on the last, Server3, process and restarted J2EE. This time, everything did start OK, but now I have a few questions I hope someone can answer.
1. Is there a limit to the number of Server processes that can exist in a single instance? If not, what would cause the J2EE servers to essentially hang on startup although they didn't look hung, just extremely slow starting up.
2. I thought when you did the initial 'Add Server' it was supposed to create a duplicate Server process. But, when I check the directory structures of the newly created Server processes, they aren't anywhere close to being the same as the original Server0 process. For example, we have a custom redirect in place when people logon to the Portal, but this wasn't transferred/copied to the new Server1 or Server2. The same was true for other customizations. Also, when looking at the structure, Server0 has approx 80,000 files and 15,000 sub-folders. When looking at the new Server1 & Server2, they are both different in size in both files and folders in respect to each other and compared to Server0. Shouldn't they all be the same?
3. A follow up to question 2. If they aren't the same and they are supposed to be the same, can we just copy the missing files & folders from Server0 to the new Servers?
4. Lastly, since I did a 'Remove Server' in Configtool for Server3, it does not appear in the MMC when the J2EE engine starts. This I expect. But, it did not remove the directory structure for Server3. If I try to manually delete the Server3 directory, it simply says it is in use and won't let me delete the structure. So, is it safe to delete this structure since it isn't being used anymore? If so, I'll stop SAP and delete the structure offline. Do I have to do any database cleanup once I do this? If so, can someone point me to some documentation as to what needs to cleaned up in the DB and how?
Thanks,
Tom

Thanks for the info.
Interesting though. I open a message with SAP and posed these same questions. Their response was similar to yours, but it opened up a whole new set of questions. What follows is the text of that message for others to benefit from (clipped for clarity):
SAP's response to the original set of questions posted here:
=====================
....1.Number of server nodes depends upon the CPU speed.J2EE Engine
can support upto 21 server nodes in a intance.
If number of server nodes is big,it will slow down the startup process.
2.When you create the "New Server"its not the dublicate server.
Its a new server.You can not copy mising files from one server to other
J2EE engine syncronises the server nodes in the instance.
3.Yes.You need to manually delete the file system.Configtool deletes
the server node from the DB....
=====================
To which I replied:
=====================
.....2. I thought when you did the initial 'Add Server' it was supposed to
create a duplicate Server process. But, when I check the directory
structures of the newly created Server processes, they aren't anywhere
close to being the same as the original Server0 process. For example,
we have a custom redirect in place when people logon to the Portal, but
this wasn't transferred/copied to the new Server1 or Server2. The same
was true for other customizations. Also, when looking at the structure,
Server0 has approx 80,000 files and 15,000 sub-folders. When looking at
the new Server1 & Server2, they are both different in size in both
files and folders in respect to each other and compared to Server0.
Shouldn't they all be the same?"
You replied:
"2.When you create the "New Server"its not the dublicate server.
Its a new server.You can not copy mising files from one server to other
J2EE engine syncronises the server nodes in the instance."
But, from actual experience, it does NOT synchronize the nodes, rather
it is a partial synchronization.
So, are the following staements true:
-When a new server process is added, ONLY standard SAP delivered files
& folders are synchronized. True or False?
-No custom files/folders are synnchronized. True or False?
-Custom values, whether part of standard SAP deliverables or custom
deliverables, are NOT synchronized. True or False?
-Each server node needs to be configured independently. True or False?
The reason I'm asking such specific questions is because of what we are
seeing. I'll use the same example from before. We modified the
index.html file for the Portal in Server0. When we added the new
server nodes, this index.html file was not synchronized. Instead, the
default index.html file was created for the new server nodes. That is
an example at the file level. Here is an example from a configuration
perspective. In Server0, in the Visual Admin tool, we have a TREX
server specified in TREX service properties. When the new server nodes
were created, this setting was NOT transferred. Therefore, TREX didn't
work until I specifically went back into VA and added the TREX settings
to the new server nodes. This is a major problem and opens up three
more questions:
1.How do we know what settings were transferred vs. those that weren't
transferred?
2.Also, if you can't copy missing files/folders from one server to
another, then how are we supposed to get those files/folders into the
new server(s)?
3. Is there a way to do a comparison between the server nodes to see
what settings are missing?.....
=====================
SAP's reply:
=====================
.....-When a new server process is added, ONLY standard SAP delivered files
& folders are synchronized. True or False? TRUE
-No custom files/folders are synnchronized. True or False? TRUE
-Custom values, whether part of standard SAP deliverables or custom
deliverables, are NOT synchronized. True or False? TRUE
-Each server node needs to be configured independently. True or False?
YES.
If any new server node is added,J2EE Engine syncronises the information
at the time of next restart......
======================
My Reply:
======================
.....1.How do we know what settings were transferred vs. those that weren't
transferred?
2.Also, if you can't copy missing files/folders from one server to
another, then how are we supposed to get those files/folders into the
new server(s)?
3. Is there a way to do a comparison between the server nodes to see
what settings are missing?.....
======================
SAP's Reply:
======================
.....1.How do we know what settings were transferred vs. those that weren't
transferred?
NO there is no way.
2.Also, if you can't copy missing files/folders from one server to
another, then how are we supposed to get those files/folders into the
new server(s)?
You need to deploy the appliactions again on the new server.
3. Is there a way to do a comparison between the server nodes to see
what settings are missing?
No there is no way......
======================
So, although I really didn't have the answers I was looking for, I confirmed the message. It seems ludicrous to me that there is no way of doing a comparison or manual synch between two server nodes. Also, I can't believe you have to configure each node independently let alone when you do a deployment you now have to deploy to each server individually, of which I haven't found any docs explaining how to do that. So if someone here has a suggestion I'd appreciate it. Although at this point, given the fact the server nodes are so out of synch as to make them almost unusable, we might just delete them all and go back to one node, although I don't want to have to do that.
Thanks,
Tom

OVM 3.0.3 - cannot add new server to VLAN group with bonded VLANs

Similar Messages

Maybe you are looking for