Parameter of timeout of BPM

Hi.
We have problems of timeout when a message enters in our BPM. Someone knows what parameters control the timeout of the BPM
Thanks
Best Regards

Hi.
We have the next problem. We have a BPM, there we send a message to other system, this system process the message and we wait the answer. The problem is that the system take 3 minutes to process the message and send the answer to SAP, but the BPM cut the communication in 1 minute exactly. We think that this is because one parameter is set in 1 minute but we don´t know what. Someone knows which is this parameter???

Similar Messages

Increase timeout for bpm workspace

Please, tell me where can i increase session timeout for bpm workspace (Oracle SOA Suite 11.1.1.4)?
Thanks.

Hello Creed -
Go to the workspace.properties file and edit the following.This is from 10.3.2.
Hopefully you can found the same in 11 also.
+# Specifies the timeout period in seconds, between client requests.+
+# If not specified the default value is 45 minutes.+
+#fuego.workspace.sessionTimeOut=2700+
BR,
Justin.

Return message for timeout in BPM

Hey
I have a synchronous scenario using BPM. My question is: If the web service I'm calling is down and I receive a timeout, can I then create a return message from BPM to the sender system that can take attributes from the original message that did not reach it's target? I have read that I can do this in case of an error, but I read someone saying this is not possible when we have a timeout...
Thanks!
regards Ole
Edited by: Ole on Sep 23, 2008 1:16 PM

Hi Ole,
You can implement a Dedadline branch in your BPM that catches your time out.
You can follow theese links:
http://help.sap.com/saphelp_nw2004s/helpdata/en/ca/7c5c41fe06cf1ee10000000a155106/frameset.htm
http://help.sap.com/saphelp_nw2004s/helpdata/en/e8/8e2d4233c8db2ce10000000a1550b0/frameset.htm
Carlos

How to pass simple parameter to XSLT from BPM 11g Data Association

Is it possible to pass a simple parameter to an XSLT from a BPM 11g Data Association (11.1.1.6.0)? Here is why I asked. I have a transform that I want to reuse across two service activities in the same process. The only difference is one integer ID value between the two activities. (Happens to be running an IPM saved search, each with a different ID.)
I tried mapping the ID value in the Data Association dialog, in addition to the XSLT mapping, but didn't work. Or is there another method I could use to reuse this transform (besides just copying it as I've done for now)? Thanks.

If I understood your scenario, the point is: you always have to pass the same dataObjects as parameters to the XSL, but you can change the values of them in an association step before the transformation.
Lets see if the following can fit your needs:
1) your project has three BusinessObjects: "SearchParam", "CommonData" and "Result"; and five process dataObjects:
- "search1", "search2" and "search" of type "SearchParam";
- "commonData" of type "CommonData";
- "result" of type "Result"
2) your XSL has "result" as target and two sources: "search" and "commonData"
3) In some part of the process flow you have a scriptTask with:
- a data association from "search1" to "search";
- a transformation with "search" and "commonData" as parameters
4) In other part of the process flow you can use the same transformation, but using the data from "search2" as parameter, adding a scriptTask with:
- a data association from "search2" to "search";
- the same transformation with "search" and "commonData" as parameters
In this scenario you are reusing the same XSL file only changing the values for one parameter.

11.1.1.5 - How can we increase the timeout of BPM Workspace ?

Hi ,
I am facing an issue where the BPM Workspace times out after every 5 mins or so.
I read in another post that we need to edit some workspace.properties file - where can I find it.
I tried using http://technology.amis.nl/blog/13768/increase-the-timeout-of-oracle-bpm-worklist-app/comment-page-1#comment-481839 but ran into some issues (should be there as my comment) where the timeout became too high.
Appreciate your help.
Thanks

I got this resolved. Added a different variable for the weblogic.xml timeout and teh web.xml timeout (Btw the digits after the timeout props are not needed if you donot need too many variables).
Also My config root was pointing to the wrong war. I changed it to point to a correct .war (relative location can be used too) & it worked just fine after that !
Thanks

Who to manage TimeOut in BPM ?

Hi Xi Experts,
In SAP WorkFlow, its possible to manage timeout in WorkItem.
I search in IR and ID on BPM design or configuration with no success . Does XI offers a simple way for this ?.
Thanks a lot for your responses.
Etienne

Yep,
it's called deadline.
You can put all the steps you want to be under this timeout condition into a Block Step and then you add a deadline branch to it. In this branch, you configure the amount of time to wait (least granularity in minutes).
We've performed with success a workaround to use timeouts with intervals less than a minute. Use a fork step. In one branch, put the steps (as you would in block step). In the other, use a transformation step and in it you use a mapping to a dummy message with a Thread.sleep() method in a UDF. With this, you can set any amount of time you want.
It was not recommended by Tobias Breyer (for those who don't know, he's the BPE developer, at SAP AG) since fork step does not execute the branches with time paralelism but with logical paralelism (meaning that they'll not necessarily be triggered at the same time). But for practical purposes, it works just fine.
Regards,
henrique.

Difference between timeout(secs) and advanced parameter ftp.timeout

Hi experts,
I have one question:
in sender communication channel, is the same to specify timeout(secs) in FTP connection parameters or to specify ftp.timeout parameter in advanced mode tab?
This is order to solve the problem of "ftp stops polling" solved with below SAP note 1083488.
Thanks
Fabio
Symptom
Sometimes, some of the XI FTP/JDBC sender channels stopped polling
permanently. However this is resolved by re-starting these channels.
Other terms
FTP sender channels, JDBC sender channels, polling stopped, stopped
polling, polling adapters.
Reason and Prerequisites
Program Error
Solution
For FTP adapter, please set the appropriate FTP timeout parameter in sender
channel configurations. Existing timeout implementation has a bug while
reading from Input. This patch solves this problem.
Edited by: Fabio Boni on May 18, 2011 5:16 PM

Hello!
If you don't have the patches mentioned on the note, you must use the advanced tab parameter. Otherwise, you can specify it in the FTP Connection parameters tab.

Changing timeout in BPM Enterprise Server

Hi,
We want to increase the timeout of all automatic activities from 60 seconds to 300 seconds.. We tried doing this by going under:-
Engines-->Name of Engine --> Execution and under retry Interval we change from 60 to 300 seconds...
We then restart the engine but the change does not take place.. The transaction still times out within 60 seconds..
Do we need to recreate the Enginer EAR after doing this? Do we need to change certain timeout settings inside Weblogic Server since we are using WLS Enterprise Server?
Any advice wud be appreciated..

Yes,
Take a look at weblogic transactions. Spefic at JTA transaction timeout.
But please, before increase this XA timeout, take a look at every resource that is participating in the transaction if it's possible to extend the transaction time otherwise you will have an transaction member aborting all the transaction due to timeout. (database , jms, ...)
Regards,
Luiz

The timeout of RFC/BPM

I have 2 scenarios
1. RFC1 -> XI -> MQ (AP1) -> XI -> RFC1 (synchronous/asynchronous bridge)
ps: AP1 gets the message from MQ and put the response into MQ
2. MQ -> XI -> RFC2 -> XI -> MQ (asynchronous/synchronous bridge)
But sometimes AP1 and RFC2 will timeout and I have to control it. I have 2 ideas:
1. Use deadline monitor of BPM, I found it in this document: http://help.sap.com/saphelp_nw04s/helpdata/en/ca/7c5c41fe06cf1ee10000000a155106/content.htm
2. Change the timeout of the SAP RFC, but I cannot find document for it.
Another question is, if I use BPM to set the timeout, could I change it in configuration?

1. Use deadline monitor of BPM, I found it in this document:
An interesting discussion related to deadline branch
Who to manage TimeOut in BPM ?
An example of deadline usage
/people/pooja.pandey/blog/2005/07/27/idocs-multiple-types-collection-in-bpm
2. Change the timeout of the SAP RFC, but I cannot find document for it.
/people/michal.krawczyk2/blog/2006/06/08/xi-timeouts-timeouts-timeouts
Another question is, if I use BPM to set the timeout, could I change it in configuration? 
I dont think so.
Is it a good design to use BPM to control the timeout?
Yes, it is while u use BPM.
[Reward points if helpful]

Regards,
Prateek

BPM: error at exactly 2500 messages after message split: no coincidence?

Hi everybody,
we poll a message, split it in BPm and than call a WebService.
We got an error exactly after 2500 messages were processed successful.
Is there a special parameter which influences the BPM?
Thanks a lot
Regards Mario

Hi,
In SXMB_ADM you can set the time out higher for the sync processing.
Go to Integration Processing in SXMB_ADM and add parameter SA_COMM CHECK_FOR_ASYNC_RESPONSE_TIMEOUT to 120 (seconds). You can also increase the number of parallel processes if you have more waiting now. SA_COMM CHECK_FOR_MAX_SYNC_CALLS from 20 to XX. All depends on your hardware but this helped me from the standard 60 seconds to go to may be 70 in some cases.
Make sure that your calling system does not have a timeout below that you set in XI otherwise yours will go on and finish and your partner may end up sending it twice
when you go for BPM the whole workflow
has to come into action so for example
when your mapping last < 1 sec without bpm
if you do it in a BPM the transformation step
can last 2 seconds + one second mapping...
(that's just an example)
so the workflow gives you many design possibilities
(brigde, error handling) but it can
slow down the process and if you have
thousands of messages the preformance
can be much worse than having the same without BPM
see below links
http://help.sap.com/bp_bpmv130/Documentation/Operation/TuningGuide.pdf
http://help.sap.com/saphelp_nw04/helpdata/en/43/d92e428819da2ce10000000a1550b0/content.htm
https://www.sdn.sap.com/irj/servlet/prt/portal/prtroot/com.sap.km.cm.docs/library/xi/3.0/sap%20exchange%20infrastructure%20tuning%20guide%20xi%203.0.pdf
BPM Performance tuning
BPM Performance issue
BPM performance question
BPM performance- data aggregation persistance
Regards
Chilla..

Interface determination : How to populate an Operation Mapping parameter

Hi experts,
I'm creating an interface determination, I have an Operation Mapping in it. This operation mapping has an inbound parameter. When Configurating this parameter I can choose between putting a constant or getting the value from a "container". Does anybody knows where this container will be? Is it possible to take the parameter from an export parameter from Integration Process(BPM)?
My interface:
BPM->IDOC
Regards
Gonzalo

Hi Stefan,
What I wanted is leaving the mapping outside the BPM, instead that I can leave it inside and the result will be the wanted. What you mean implies something similar.
I'm going to explain why, from the process dessign point of view, I want to leave the mapping outside.
1.-I send an IDOC from my ERP
2.-This IDOCs starts a BPM who, in a synchronous way, makes some updates in a DB.
3.- Functionally speaking this updates could return a 0 if OK or a -1 if NOK
4.-The BPM have to return an ACK to the ERP.
For constructing this ACK I need my original IDOC and the result of the updates (-1 or 0).
-If I put the mapping inside the BPM it will work (and that will probably be the final solution).
-But, for a better performance and dessign, I wanted to leave the mapping outside.
-I also want to know if the container in the interface determination we talked before can be used or what it means. (So let me know if you find out something about)
-The third reason is that I find interesting speak about this topics in the forum if you know what I mean :-D
Regards
Gonzalo

RFC connection results in "Timeout during connection setup"

Hello Guys,
The RFC ABAP connection to the Solution Manager encounters connection error: "/ CPIC-CALL: 'ThSAPCMINIT' : cmRc=27 thRc=242#Timeout during connection setup."
The Solution Manager has following details:
SAP Solution Manager (700 15)
ORACLE 10.2.0.2.0
HP-UX
The R/3 QAS Customer 1 system has following details:
SAP R/3 Enterprise (620 54)
ORACLE 9.2.0.8.0
HP-UX
The R/3 QAS Customer 2 system has following details:
SAP R/3 Enterprise (620 59)
ORACLE 9.2.0.8.0
HP-UX
The RFC ABAP connection from <SID Solution Manager> -> <SID R/3 QAS Customer 1> is working correctly.
The RFC ABAP connection from <SID R/3 QAS Customer 2> -> <SID Solution Manager> is working correctly.
The RFC ABAP connection from <SID R/3 QAS Customer 1> -> <SID Solution Manager> encounters connection error:
ERROR timeout during allocate
LOCATION SAP-Gateway on host hemisrq.services.retail.tc.services.retail.tc / sapgw01
DETAIL no connect of TP sapdp02 from host conssmp.servom host <host name Solution Manager> after 22
COMPONENT SAP-Gateway
COUNTER 1152
MODULE gwr3cpic.c
LINE 1820
RETURN CODE 242
SUBRC 0
RELEASE 640
TIME Thu Jun 5 10:55:15 2008
VERSION 2
Here's the dev_rfc0 log file
Trace file opened at 20080605 101956 METDST SAP-REL 640,0,235 RFC-VER 3 985555
======> CPIC-CALL: 'ThSAPCMINIT' : cmRc=27 thRc=242
Timeout during connection setup. Please check partner availability
ABAP Programm: RSRFCPIN (Transaction: SM59)
Called function module: RFC_PING
User: SAPBEHEER (Client: 000)
Destination: <SID Solution Manager>CLNT010 (handle: 2, , {4846C6DC-14A2-0F1F-E100-0000AC1B29D8})
Error RFCIO_ERROR_SYSERROR in abrfcpic.c : 2277
CPIC-CALL: 'ThSAPCMINIT' : cmRc=27 thRc=242
Timeout during connection setup. Please check partner availability
HOST =<host name Solution Manager>
SERV =sapdp02
Checked the error code 242 "GW_TIMEOUT" and found:
Connection setup to the remote gateway has been closed because timeout has been exceeded.
The time limit can be set in parameter gw/timeout.
Changed parameter gw/timeout to value 10000, but still encounter same error message.
From OS level <SID R/3 QAS Customer 1> i can ping the <host name Solution Manager>.
fvb1:/home/stampg$>ping <host name Solution Manager>
PING <host name Solution Manager>: 64 byte packets
64 bytes from 172.27.68.239: icmp_seq=0. time=1. ms
64 bytes from 172.27.68.239: icmp_seq=1. time=1. ms
64 bytes from 172.27.68.239: icmp_seq=2. time=1. ms
64 bytes from 172.27.68.239: icmp_seq=3. time=1. ms
64 bytes from 172.27.68.239: icmp_seq=4. time=1. ms
64 bytes from 172.27.68.239: icmp_seq=5. time=1. ms
conssmp.services.retail.tc PING Statistics----
6 packets transmitted, 6 packets received, 0% packet loss
round-trip (ms) min/avg/max = 1/1/1
Any suggestions where to look ?
Regards,
Gidion

Hello Gidion,
can you please verify the hostnames/FQDN's? Because:
LOCATION SAP-Gateway on host hemisrq.services.retail.tc.services.retail.tc / sapgw01
host hemisrq.services.retail.tc.services.retail.tc
It seems to me that somewhere the domain is double used.
Additionally:
Sometime there is sapgw 01, sometime sapdp 02. Can you please check the correct service numbers / system numbers?
Regards
Holger

SOAP: "XI.Timeout" module in the sender adapter

Hi,
Could you please explain in detail, how to enter the XI.timeout module in the soap sender adapter.
Regards,
Vishnu.

Hi Vishnu,
The default timeout value for synchronous calls is 5 minutes. You can increase this value by setting parameter XI.Timeout in the module parameter table of the SOAP adapter. The value must be given in milliseconds. For example, value 600000 represents the timeout value of 10 minutes. This parameter is not recognized in systems prior to SP13.
In the Module tab of the Communication channel you can find Module Parameters can be specified under Module Configuration section.
Add the XI.Timeout Parameter with some Parameter Value.
regards
Ganga

XMBWS.Timeout in soap receiver channel not working

Hello
I have a requirement where my soap receiver channel should time out in 20 sec from the time it had shot a webservice request.
I tried setting the module parameter XMBWS.Timeout to 20000 but it didnt work. I assume this parameter should be set for the standard module i.e. sap.com/com.sap.aii.af.soapadapter/XISOAPAdapterBean.
Currently my receiver channel is timing out after every 3 min and that might be because the parameter xiadapter.inbound.timeout.default in SAP NWA is set to 180000.
Any other parameter to be set so that channel takes time out duration from module parameter.
Note: we are working on PI 7.1 EHP1
Regards
Shailesh

>
Shailesh Kunjiraman wrote:
> i doubt if this can be reduced to value lower than a minute.
i agree. A minute is usually the minimum value for lot many parameters.

Timeout in synchronous SOAP-Proxy communication

Hi,
I have a synchronous SOAP-Proxy communication (3rd party - XI - ERP). 3rd party is always the initiator of the communication.
Is there a general rule about who should set a timeout? Does it should be set by a 3rd party, XI, or ERP? In our scenario it shouldn't be longer than 30 seconds.
If it needs to be set on SAP side, where it should be defined? On XI or on ERP, or on both systems?
Which SAP parameter is used for setting the timeout for synchronous communication that does not affect other already working ways of communication, like asynchronous.
Thanks for answers.
Janos

Hi,
The timeout property needs to be set at XI level. For SOAP sender timeout check sap note no. 856597 which reads as The default timeout value for synchronous calls is 5 minutes. You can increase this value by setting parameter XI.Timeout in the module parameter table of the SOAP adapter. The value must be given in milliseconds. For example, value 600000 represents the timeout value of 10 minutes. This parameter is not recognized in systems prior to SP13.
Thanks!

Parameter of timeout of BPM

Similar Messages

Maybe you are looking for