Part of touchscreen not active

All of the sudden, a portion of the touchscreen does not react. It is a band spanning horizontally and located in a terrible place: where the newest visual voicemail is displayed, the address bar above the google search within safari, where you turn WiFi on and off in settings, etc. So the problem is in the same place in all applications. From a tech perspective, does it make sense to have a band like this not respond? Is there anything I can do besides get a new phone?
Thanks in advance

If the standard troubleshooting steps do not resolve it, which in order are powering your iPhone off and on, Reset, Restore, your only other option is calling AppleCare (800) 694-7466, or making an appointment at an Apple Store if there is one nearby.

Similar Messages

My iPhone 5 bricked when upgrading to iOS 7. Now it is stuck at the activation part and will not activate.

I downloaded the iOS 7 but it would not install so i tethered it to my computer the connect to iTunes screen came on the iPhone. But after a few minutes, it crashed and iTunes told me it was in recovery mode and that it will be restored to factory setting. After that process, it is stuck on the activation part and will not activate. Please advise!

All of Apple's servers...including the activation servers are pretty much flooded with users like you doing the same thing. Be patient and keep at it...or wait till the traffic to them has decreased and then try again. Coming back to it tomorrow (if that's a viable option for you) will likely increase your chances of not having issues.

After adding list view into the web part page, the items and list control ribbon is not activated.

I created new webpart page and added one list view web part into the page.
However I can see the ITEMS and LIST tabs on ribbon area, but all the buttons are deactivated.
Do I have to activate any feature for this or any settings are needed for the webpart?
I already have full permission for this site.
For your easy understand I added the screenshot.

Thanks for you advice.
However I am currently using the context menu and edit link in the view.
My Client keep complaining about the ribbon is not activated even thought it works fine in the SharePoint 2010.

IPhone Touchscreen Malfunction Not Activated

Hi I bought my iphone on ebay (nib) and while I was playing with it I noticed that I could not touch the little info icon on the bottom right of the screen (not activated) I tried everything and it appears to not respond to touch in that area. I wanted to know if I could take it to an apple store for check up and if I would need the receipt in order to get help from apple.

Go here and enter your phone's serial number to see its warranty information:
[Apple warranty lookup|https://selfsolve.apple.com/GetWarranty.do]
You should be able to take it in for exchange, since no one's owned one past a year yet. The warranty is valid whether it's activated or not, and began at its first purchase... unless it's a refurb unit, which has a later beginning date.
(In a little over a month, hundreds of thousands will begin to fall out of warranty, if they don't get extended with Applecare. Considering the touch screen failures, people might be wise to extend.)

When I open logic express 8 with eyetv open but not active and i close logic express 8 and make eyetv active it won't show closed captioning even though closed captioning is turned on

when I open logic express 8 with eyetv open but not active and i close logic express 8 and make eyetv active eyetv won't show closed captioning even though closed captioning is turned on. When I totally close eyetv and reopen eyetv and open a live tv window the closed captioning comes back. I never noticed this with os leopard, Just after i installed os snow leopard. All software is up to date only I think, thanks to apple they droped support for logic express. Thanks for any suggestions.

Does toggling CC off & back on bring it back?
"Try Disk Utility
1. Insert the Mac OS X Install disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu at top of the screen. (In Mac OS X 10.4 or later, you must select your language first.)
*Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
3. Click the First Aid tab.
4. Select your Mac OS X volume.
5. Click Repair Disk, (not Repair Permissions). Disk Utility checks and repairs the disk."
http://docs.info.apple.com/article.html?artnum=106214
Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.
(Safe boot may stay on the gray radian for a long time, let it go, it's trying to repair the Hard Drive.)
If perchance you can't find your install Disc, at least try it from the Safe Boot part onward.

Remote desktop client software not active

I'm sorry if this has been asked before but I'm a bit bewildered by this errormessage (and I couldn't get a hit when I searched for it) when I try to drag a file from the xserv to the macbook pro desktop, remote desktop client software not active.
The macbook has the ard server and connects to the xserv ppc. It connects over the internet.
The xserv is behind a iptables fw and I have forwarded 3283 tcp/udp plus 5900 udp/tcp to the server. Have I forgotten a port ?
I've read through http://www.starkpr.com/ard.htm as well as http://www.macosxhints.com/article.php?story=20070302234400232&query=vnc%2Bsimpl e%2Bset%2Bup
and tried to find out more from the discsussions here.
The macbook pro sits behind an airport which is hooked into the dsl modem. Do I need to configure port forward in the airport as well.
Connecting to the xserv and working on it works great but the copy file transfer fails.

Hi there I took new try at this and this is what finally solved it for me.
The earlier answer I got was very good advise but I had already done that bit, actually I might have overdone it a bit I had checked all the boxes under the useraccount on sharing.
Back to business.
Firewalling. I realised I need to open and portforward at both locations and remeber it's booth tcp and udp.
So at the xserve location I needed to forward 3283 and 5900 both tcp and udp from outside to the IPnumber of the xserve.
At home with my macbook I needed to do the same.
However this did not solve it, I had forgotten one software on the macbook. On the xserve I had installed ARD upgraded it to 3.1 AND installed the upgrade for ARD 3.1 client. The client part I had forgotten at home. So once my ARD and ARD client software matched I could connect to the xserve and drag and drop files booth ways.
ARD wasn't running on the xserve I just had it installed along with the client software.
So portforwarding in firewalls and the same software and versions in all locations seems to have solved it for me.
A small note enabling/disabling the firewall in macbookpro did nothing for me since when enabled ARD rules were in place and active so it still worked.
I hope I made some sense.
Message was edited by: tindome
Message was edited by: tindome

My Windows 8.1 is not activated?

HI,
As I was going through buying Microsoft Office just last night. I came across my computer specs an OS details and it says that my current System isn't activated. I bought this laptop as a return/floor model/refurbished product at Best Buy and it did not come with said Windows DVD or papers. The computer, i was told, was only reset and checked for physical and hardware/sytem damage. When I bought it it had alrerady had everything installed. All I had to do was register it under my personal info ect.
So know I'm left without being able to activate my laptop the I bought under a month ago and I have no idea how to fix it. Anyone have any tips on how to activate the OS. Is it even necessary to activate it. Will I be able to download and run all my programs like, Autodesk software: Revit, AutoCAD, Maya and Design Suite etc, MS Office, Adobe, without any problems?
PS my PC say its got a current keycode active, but on the <Control Panel> <System and Security> <System> <Windows Activation> it says windows not activated. When I follow the active -> Activate Online, it says cannot activate online.
Any help ya'll can throw at me is very well appreciated. Thank ya'll in advanced.

Desco,
Welcome to the HP Forum.
I am NOT the best one to answer this question -- I do not know that much about how all the ways a system gets into this state; I might miss something obvious.
I will try to help.
Because you bought the computer at a legitimate local retail store, you can try going back to them and see what they say -- Best Buy on the West Coast does have a varied history of customer satisfaction, so good luck with that.
You might be able to get help from Microsoft Windows -- yes, really. If the software is legitimate, they might be able to help.
Start here: Why can't I activate Windows?
This document is not really a match to your situation; it is a "well, this is your creek and paddle area".
You might be able to get help over the phone -- again from Microsoft -- the tech probably knows the questions to ask and you have, well, what you have. You can ask.
You might be able to get help from an actual Microsoft Store if you live in or near a large metropolitan area when you can find a Microsoft brick-and-mortar retail store. Take your Best Buy receipt and plead your case. This sometimes works when talking on the phone will not -- you can prove who you are, at least.
============================================================================
Purchase Windows 8.1 Pro
If you purchased the computer for enough off from the original purchase price, think of this as the "bait and switch" part of the deal -- you may have to purchase a new copy of Windows 8.1 Pro.
The good news about purchasing new software -- it's yours and the problem is solved.
Click the Kudos Thumbs-Up to say “Thanks" .
Although I strive to reflect HP's best practices, I do not work for HP.
Kind Regards,
Dragon-Fur

Zrps (copy of vprs) not active in sales order in order to post it to copa

Hi All,
Our company is selling products to its other entities (in other parts of the world) who are not in SAP.
We should be selling to them at 110% of the actual cost.
I copied VPRS to ZRPS. In the Pricing Procedure, i placed ZRPS on top, followed by ZPRI (it has condition record for 110%), ZNOR (manual condition type, where in if the user wants to enter a price manually, then can enter).
lf the cost of the material is $30, in the PP, ZRPS is inactive with $30, ZPRI is active with $33, no ZNOR. and the rest below to it looks beautiful with the totals.
But what's the problem is, in order to get ZRPS into COPA it has to be active, and it is not active in current situation. As ZRPS is mapped into I/C COGS in COPA as this can be seen at the time of billing.
I want this ZRPS to be active in order to get this solved. I also added VPRS at the bottom. It has a red bomb with $0 value. It did nt work either.
Hope I am clear.
Please suggest me on this or any other solution.
Thanks in advance.
Regards,
Vamsi.

Kindly check at you Item Category in VOV7 whether Determine Cost checkbox is activate or not.
As before maintaining Condition Type in the Pricing procedure ,it should be activated at Item Category level.
Best regards,
Ankur

[SOLVED] Touchscreen not working

I have a generaltouch touchscreen, which was working in ubuntu 10.04. Now I'm trying to get it working in Arch, and it doesn't work. Symptoms are very interesting:
1) mouse cursor doesn't move when I try using touchscreen, but button press and release events are processed correctly
2) "lsusb" doesn't show device name, just vendor id: "Bus 001 Device 005: ID 1ddb:0001"
3) "xinput" lists touchscreen as "HID TOUCH HID Touch Panel id=10 [slave pointer (2)]" in virtual core pointer section
4) "xinput test 10" correctly shows button press, release and motion events, all of which look quite sane
The most strange part is that although mouse cursor doesn't move, xinput test does show correct motion events. I feel that it could be easily fixed, but I cannot find config/manual to look into. Any help would be very welcome.
PS. Relevant output from Xorg.log is as follows:
[ 10.460] (II) config/udev: Adding input device HID TOUCH HID Touch Panel (/dev/input/event2)
[ 10.460] (**) HID TOUCH HID Touch Panel: Applying InputClass "evdev tablet catchall"
[ 10.460] (II) Using input driver 'evdev' for 'HID TOUCH HID Touch Panel'
[ 10.460] (**) HID TOUCH HID Touch Panel: always reports core events
[ 10.460] (**) evdev: HID TOUCH HID Touch Panel: Device: "/dev/input/event2"
[ 10.460] (--) evdev: HID TOUCH HID Touch Panel: Vendor 0x1ddb Product 0x1
[ 10.460] (--) evdev: HID TOUCH HID Touch Panel: Found 3 mouse buttons
[ 10.460] (--) evdev: HID TOUCH HID Touch Panel: Found absolute axes
[ 10.460] (--) evdev: HID TOUCH HID Touch Panel: Found x and y absolute axes
[ 10.460] (--) evdev: HID TOUCH HID Touch Panel: Found absolute tablet.
[ 10.460] (II) evdev: HID TOUCH HID Touch Panel: Configuring as tablet
[ 10.460] (**) evdev: HID TOUCH HID Touch Panel: YAxisMapping: buttons 4 and 5
[ 10.460] (**) evdev: HID TOUCH HID Touch Panel: EmulateWheelButton: 4, EmulateWheelInertia: 10, EmulateWheelTimeout: 200
[ 10.460] (**) Option "config_info" "udev:/sys/devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.6/1-1.6:1.0/input/input2/event2"
[ 10.460] (II) XINPUT: Adding extended input device "HID TOUCH HID Touch Panel" (type: TABLET, id 10)
[ 10.461] (II) evdev: HID TOUCH HID Touch Panel: initialized for absolute axes.
[ 10.461] (**) HID TOUCH HID Touch Panel: (accel) keeping acceleration scheme 1
[ 10.461] (**) HID TOUCH HID Touch Panel: (accel) acceleration profile 0
[ 10.461] (**) HID TOUCH HID Touch Panel: (accel) acceleration factor: 2.000
[ 10.461] (**) HID TOUCH HID Touch Panel: (accel) acceleration threshold: 4
[ 10.461] (II) config/udev: Adding input device HID TOUCH HID Touch Panel (/dev/input/mouse1)
Last edited by xop (2012-11-24 12:41:18)

Hi. Thanks to your post i was able to solve mine.
If anyone is wondering, here's what i believe to be an explanation, based on third party sources and searching.
Symptom: touchscreen always clicks at the same place (e.g. top-left corner).
1) the touchscreen manufacturer id (0x1ddb) and product id (0x1) are currently not into the usb vendors database (even after update-usbids)
lsusb -v:
Bus 002 Device 005: ID 1ddb:0001
iManufacturer 1 HID TOUCH
iProduct 2 HID Touch Panel
2) as such, the kernel (through udev) tried to discover the nature of it blind folded (i'd be interested to know on what basis), and ends up thinking that's a tablet device (and not a touchscreen)
dmesg:
[ 2.298156] usb 2-1.7: new full speed USB device using ehci_hcd and address 5
[ 2.391784] usb 2-1.7: configuration #1 chosen from 1 choice
[ 2.394379] input: HID TOUCH HID Touch Panel as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.7/2-1.7:1.0/input/input7
[ 2.394442] generic-usb 0003:1DDB:0001.0005: input,hiddev96,hidraw4: USB HID v1.01 Mouse [HID TOUCH HID Touch Panel] on usb-0000:00:1d.0-1.7/input0
3) tablets (e.g. wacom) have 4 axis: X, Y, Z (because the pen can be detected when closing up to the surface, or somtimes will send out pressure information) and Rotary X (i would guess the angle of the pen)
xinput list-props 12:
Device 'HID TOUCH HID Touch Panel':
Axis Labels (271): "Abs X" (281), "Abs Y" (282), "Abs Z" (283), "Abs Rotary X" (284)
Button Labels (272): "Button Left" (143), "Button Middle" (144), "Button Right" (145), "Button Wheel Up" (146), "Button Wheel Down" (147)
4) because the driver is generic, it fails associating the correct data to the correct axis; by testing the device (xinput test 12 -- where 12 is the id of the HID Touch Panel found through xinput list), you can see that it's actually putting the X and Y coordinates to the Z and Rotary X axis; and that's exactly why when touching the screen, the cursor will always go to the top left corner (0,0).
xinput test 12:
motion a[0]=0 a[1]=0 a[2]=668 a[3]=900
motion a[0]=0 a[1]=0 a[2]=669 a[3]=912
motion a[0]=0 a[1]=0 a[2]=672 a[3]=928
a[0] and a[1] are obviously the 2 first axes X and Y, a[2] and a[3] the others (Z and Rotary X)
5) now for the solution, what we want is force the usbhid kernel module to consider the device as a 2 axis touchscreen, not a tablet.
Given the large number of unknown/OEM/slightly differring USB devices out there, the Linux kernel already has some tweaks to force some behaviours, called quircks (list of quircks in hid.h), and there is one especially for this: HID_QUIRK_MULTI_INPUT. The hid.h file will give you the hex code for the quirck.
Syntax is quirks=vendorid:productid:quirckhexcode
modinfo usbhid
parm: quirks:Add/modify USB HID quirks by specifying quirks=vendorID:productID:quirks where vendorID, productID, and quirks are all in 0x-prefixed hex (array of charp)
You can set quircks either directly into the kernel like you did (into the hid blacklist), or at module loading time (modprobe usbhid quirks=1ddb:0x1:0x40), or at boot time by adding usbhid.quirks=0x1ddb:0x1:0x40 to the kernel boot line.
After rebooting/reloading, there is a new xinput device available (with the same name), but only 2 axes, and it works, and can be calibrated.
However, i'd be curious about:
* what exactly is the HID_QUIRK_MULTI_INPUT doing ? From third party sources, i think it will break the device into 2 devices, explaining why xinput -list shows a new device; i guess that the first one has X and Y, and the other Z and Rotary X
* since the device does not actually have 4 axes, any way to remove/disable the 2nd device permanently ?
* why did usbhid fallback to tablet mode ?
* is forcing the use of quirks the right way to go inside the blacklist ? Shouldn't the new vendor id and product id be added to the product database, and set the device to touchscreen type, and not force by using quircks ?
Thanks for any follow up...

My laptop sucks battery dry when its not active

I have a compaq 615 laptop, windows 7 32bit. Some days ago i noticed that my battery runs down to below 7% when its not active, this happens when i use the battery to about 60% or 50% before shutting down the system and try to on it after some hours. It doesn't happen when i shut down at 100%. Right now i am confused, i don't know what to do because its seems the laptop sucks the battery when its not active. Pleas i need your advise on what to do

Try calibrating the battery from HPSA. You can test the battery through there.
The battery test is part of HPSA in Windows 7.
Follow this document. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00821536&lc=en&cc=us&dlc=en
THX

How do i get the "part of project not played" error to stop?

My garageband app lately has been absolutely awful and everytime i do any recording will not let me play it back if im playing multiple tracks over eachother. In one project I have there is only one real acoustic track and when trying to record over it I am not able because a message is constantly popping up saying that the project can't be played because it has too many tracks, effects, or notes. I don't understand how this can be the case as I only have two tracks, no effects and minimal notes so there doesn't seem to be any reason why the project shouldn't be able to be played or recorded in real-time. Any help/suggestions are greatly appreciated.

In addition to Edgar's explanation -
is your profile signature "GarageBand (Mac) '11, OS X Mountain Lion (10.8.5)" still current? Just in case you already upgraded to OS X Mavericks, make sure you updated to the latest version 10.9.2. The 10.9.1 version had problems with the memory management, that have been fixed in the new update.
You can check, how much memory is used by your applications from the "Activity Monitor" utility. You will find it in the "Utilities" folder in the "Applications" folder. Launch it and click the "Memory" tab, to see which applications are competing with GarageBand for the memory and should better be closed.
To free as much memory as possible at once, restart the computer, if you are continually seeing "Part of project not played".

I updated my Iphone which is successful but it is not activating.

I updated my Iphone which is successful but it is not activating.

Okay.. I guess you can't tell us the complete message.
This is normally part of a message that indicates the Iphone was jailbroken or unlocked by someone other than the carrier.
If so, we cannot help you here and you need to work with your carrier.
We are just users, not Apple support.

ER : 10338256 : AF:ACTIVEOUTPUTTEXT IN TASK-FLOW-CALL DOES NOT ACTIVELY CHA

hi
In the context of Re: Task Flow API for programmatically retrieving parameters? and "The official ADF EMG bug and ER thread", this forum thread is Re: Task Flow API for programmatically retrieving parameters? to get your vote or feedback on one specific ER:
- 10338256, "AF:ACTIVEOUTPUTTEXT IN TASK-FLOW-CALL DOES NOT ACTIVELY CHANGE"
Among other bugs, it was created in the context of forum thread "show server time on a page (automatically updating)" ...
at show server time on a page (automatically updating)
... where part of the feedback from Oracle support (SR 3-2369020191) was
"... we have the limitation in ADS today that we can't add an ADS component to a page through a PPR request. For example, a task-flow-call, or a simple button click with the attribute partialSubmit=true ..."
(But, regardless the intent of this forum thread, feel free anytime to pursue other means to attract the attention of Oracle to a specific ER. Possibly by creating a service request referring to an ER, or by any other way you see fit.)
many thanks
Jan Vervecken

+1

Home Move & BT Vision Not Activated Properly - nea...

Hello,
Apologies if there is an answer to this somewhere but I did a search and couldn't find anything relevant... also apologies that this is quite long but the whole saga has been going on for ages so there's a lot to write.
I hope someone is able to advise as to how I can finally get this sorted out though before I have a breakdown!
- On 15/11/11 I contacted BT via the website to inform them of my home move from A to B and that I wanted to stop service at A on 21/11/11 and to start at B on the same date or asap thereafter
- I received a standard email reply stating that service would start at B for phone, broadband & BT Vision 22/11/11
- I then received a call (not sure of exact date) to say that there unfortunately would be a delay to Broadband & Vision
- Phone service activated at B (new address) 23/11/11
- Broadband activated at B 26/11/11
- BT Vision activated 03/12/11
- However I then noticed that Replay & On Demand (which had been part of my package) were still not activated (i.e. they were still PAYG)... I gave it a few days
- I called BT in the afternoon of 08/12. I spoke to a few different people (Indian call centre I believe) who didn’t have a clue and was then put through to a helpful chap (I think in UK)... we went through everything and although he couldn’t see what the problem had been he did switch me to a new package: dual package (phone & broadband: and switching from Broadband Option 2 to Option1) + BT Vision Unlimited (i.e. not also including Film Club) + unlimited weekend & eve calls (previously had just been weekend).
- He also said that they would knock a few quid off for the first 2 months because of the hassle and that it would be a new 12 month term
- HOWEVER he couldn’t have it set up immediately as one of the first people I’d spoken to before being put through to him had logged it as a fault and apparently the new order can’t be put through and activated until the fault has been cleared
- He informed me the new activation date would be 15/12/11
- The phone activation happened 15/12/11 (i.e. switching from unlimited weekend calls to evening + weekend)
- As of 22/12 BT Vision had still not been activated properly as I still didn’t have On Demand, Reply & Film Club... I was told that the order was still shown as open. There was an issue and the guy I spoke to said he would try and get to the bottom of it, sort it out and would call me back the following evening
- A couple of hours later I received an email to say that my order was cancelled (?!)
- Now it is possible that the person I spoke to tried to call me on 23/12/11 but I was out
- 24/12/11 (I think, it may have been the evening of 23rd) I sent an email via bt.com asking what was going on
- I then received a call 29/12/11 to say that the old order needed to be cancelled (I thought that it had been already, according to the email received on 22nd) & that then a new order would have to be put through. This would take at least 24hrs and that I should then be notified in 48hrs to let me know when the new activation date would be. Apparently there has been an “over-capacity” issue....
- On 30/12/11 the order status online showed that an order had been put through on 22/12/11 but the activation dates were still showing as 15/12/11.
- 02/01/12 I still had not been notified as to when the new activation date would be (48 hours would have been 31/12/11 PM)
03/01/12 - someone from BT called and asked if my phone & broadband were OK. I said yes but that I’d not been having a problem with them anyway, it was BT Vision. He said that was a separate department and that I would have to speak to someone there. OK, fine I replied but I’d never had a prob with the phone & broadband anyway (i.e. so why the call in the first place as I’d not made an issue of that)... he just repeated that I would need to spk to someone at BT Vision. Fair enough.
- 08/01/12: I checked on bt.com and now my account was showing as having no outstanding orders at all.
- Again I checked BT Vision and On Demand, Replay and Film Club had still not been activated. Plus my online account still seemed to be showing that I had Broadband Option 2 (not 1) as well.
- I sent another email via bt.com 08/01/12. Pretty much detailing the whole timeline as I have here - and obviously asking that someone *please* let me know what was going on.
- I received a call today (09/01/12) from someone at BT asking if it was all now OK as apparently it should be. I said that certainly it hadn’t been the last time I checked (last night).
- He said that he could log it as a a fault but I said I was loathe to do that without double checking as that would delay it further (see what happened when it was previously logged as a fault when apparently it shouldn’t have been) and this had been going on since November as it was.
- I said he would check tonight and turn everything off & on again etc and see if that would make a difference.
- He then said that he would just check what the system said was active... unfortunately he then cut me off and didn’t call back
- This evening (09/01/12) I checked BT Vision when I got home but still no On Demand, Reply & Film Club (well they are there, but wanting to charge me).
- I’ve restarted the hub and also the Vision Box but it hasn’t made a difference
Does anyone have any ideas what I should do next? Clearly emails and calls aren't doing me any good at all and I'm getting incredibly frustrated...
All advice very gratefully received!
Thanks,
LK

Hi LondonKitchener
I am really sorry that you have had so much difficulty getting your Vision working properly. Occasionally we can have problems with how the order is built and it sounds like certain essential elements have been left out of activation, it should just be a case of getting this reported and applied but sometimes it can take a while to get everything figured out and set up correctly.
I'll happy to help you out with this and make sure you know what's happening each step of the way. We can act as a point of contact for you which should make things a bit easier.
Could you drop me in an email please? Use the 'contact us' form in my forum profile under the 'about me' section. You can find it by clicking on my username.
Thx
Craig
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)”
td-p/30">Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Selection printing not active in photosmart C6280

I am using this printer with Windows 7 Premium and on my Safari browser I cannot select part of a page to be printed it is not active I can only select pages not just a paragraph . Is there a fix for this?

Hello,
Thanks for the post. Windows 7 premium, can you select area using Explorer? How about Chrome or another browser? I've attached a link here to the APPLE support, I might also suggest posting this question there. Good Luck!
http://www.apple.com/support/safari/
I worked for HP but my posts and replies are my own....Thank you!
*Say thanks by clicking the *Kudos!* which is on the left*
*Make it easier for other people to find solutions, by marking my answer with (Accept as Solution) if it solves your issue.*

Part of touchscreen not active

Similar Messages

Maybe you are looking for