Please Help: 3550 lab switch locked by radius server

Hi All,
Any idea? After clean up all routers and switches config files, sw3 still asks for radius username and password.
When console login and using 3550 password recovery procedure, it still asks for username and password.
When config aaa new-model, no username is asked only the passowrd cisco in typed in. (please see detail config file in the following)
Note: This is for CCIE R&S home lab rack.
==========
// radius server locks sw3
Access-Server#9
[Resuming connection 9 to sw3 ... ]
User Access Verification
Username:
Username: cisco
Password:
% Backup authentication
00:27:36: %RADIUS-4-RADIUS_DEAD: RADIUS server 150.100.1.254:1645,1646 is not responding.
00:27:36: %RADIUS-4-RADIUS_ALIVE: RADIUS server 150.100.1.254:1645,1646 has returned.
Username:
===========
sw3#sh run
Building configuration...
Current configuration : 4655 bytes
version 12.2
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
hostname sw3
aaa new-model
aaa authentication dot1x default group radius
aaa session-id common
mls qos
ip subnet-zero
ip routing
no ip domain-lookup
dot1x system-auth-control
dot1x guest-vlan supplicant
no file verify auto
interface FastEthernet0/11
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/12
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/13
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/14
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/15
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/16
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/17
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/18
switchport mode access
dot1x pae authenticator
dot1x port-control auto
dot1x guest-vlan 999
dot1x auth-fail vlan 999
interface FastEthernet0/19
switchport mode dynamic desirable
channel-group 1 mode desirable
interface FastEthernet0/20
switchport mode dynamic desirable
channel-group 1 mode desirable
interface FastEthernet0/21
switchport mode dynamic desirable
interface FastEthernet0/22
switchport mode dynamic desirable
interface FastEthernet0/23
switchport mode dynamic desirable
channel-group 2 mode desirable
interface FastEthernet0/24
switchport mode dynamic desirable
channel-group 2 mode desirable
interface GigabitEthernet0/1
switchport mode dynamic desirable
interface GigabitEthernet0/2
switchport mode dynamic desirable
interface Vlan1
no ip address
shutdown
ip classless
ip http server
ip http secure-server
radius-server host 150.100.1.254 auth-port 1645 acct-port 1646
radius-server source-ports 1645-1646
radius-server key cisco

try to do password recovery per cisco doc, but config.text file is missing from flash dir:
switch: dir flash:
Directory of flash:/
2 -rwx 5276 syslog
3 -rwx 0 env_vars
4 -rwx 7131928 c3550-ipservicesk9-mz.122-25.SEE.bin
5 drwx 64 crashinfo
24 -rwx 326 system_env_vars
7 drwx 192 c3550-i9q3l2-mz.121-13.EA1a
26 -rwx 24 private-config.text

Similar Messages

Please help me I'm locked out of my phone...

please help me i've been locked out of my phone and I'm prepared to restore it, i know thats what has to be done, but when i plug i connect it to the computer it says i have to allow access to my phone which i cant do b/c i can't get into it so i cant sync therefore i cant restore. please help me.

See here and note the part about forcing it into recovery mode. http://support.apple.com/kb/HT1212
Or, access it through iCloud and erase it there.

I have restored my iphone and its saying time remaining is about 24 hours can you please help. can i switch the phone back on ? please help ??? :(

after there being an error in trying to update the software it said i have to restore my phone which i have done but says time remaining is about 24 hours . can you please help ? i just want to switch my phone on again .

Hello lyndsey1430,
From what I can gather, it sounds like you're having issues restoring your device. After reviewing your post, I have located an article that can help in this situation. It contains helpful advice concerning recovery mode:
If you can't update or restore your iPhone, iPad, or iPod touch
Use recovery mode
You might need to use recovery mode to restore your device in these cases:
iTunes doesn't recognize your device or says it's in recovery mode.
You see the Apple logo onscreen for several minutes with no progress bar.
You see the Connect to iTunes screen.
Learn what to do if you see the progress bar onscreen for several minutes.
To put your device into recovery mode, follow these steps:
Turn off your device and leave it off.
Plug in your device's USB cable to a computer with iTunes.
Hold down the Home button on your device as you connect the USB cable. Keep holding down the Home button until you see the Connect to iTunes screen.
When you see this screen, release the Home button. If you don't see this screen, try steps 1 through 3 again.
When your device is connected, iTunes will open. You'll see a message saying that iTunes has detected an iPhone, iPad, or iPod touch in recovery mode.
Use iTunes to restore your device. Restoring in recovery mode will erase your device. If you previously synced with iTunes or iCloud, you might be able to restore from your backup.
Get more help
Learn what to do if you don't see your device in iTunes for OS X, or in iTunes for Windows.
If you put your device into recovery mode by mistake, restart it. Or you can wait 15 minutes and your device will exit recovery mode by itself.
Thank you for contributing to Apple Support Communities.
Cheers,
BobbyD

PLEASE HELP: iPod Touch is locked up.

PLEASE HELP: My iPod touch fourth generation has a zoomed in view and is locked like that. How do I get it back to normal size?

This is asked and answered often. the forum search bar is on the right side of this page.
It is also covered in the manual - zoom feature:
iPhone User Guide (For iOS 4.2 and 4.3 Software)
Double tap with three fingers

3850 switch configure with radius server

wifi useres authenticate with radius server configure required
Posted by WebUser Raja Sekhar from Cisco Support Community App

Kindly check the following links for configuring 802.1x
http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/security/configuration_guide/b_sec_1501_3850_cg_chapter_0101.html
http://www.cisco.com/en/US/docs/switches/lan/catalyst3850/software/release/3.2_0_se/security/configuration_guide/b_sec_1501_3850_cg_chapter_01110.html

Please help, After mac 10.5.8 mail server migrated to snow leopard server?

Hi,
All my old emails date has changed to the date on which i migrated to snow leopard server, all the old emails show as they arrived on 31st of Dec 2009.
How do I fix it. Very Very important to me to have the arrived date.
Please help
Thanks,
Gulab Pasha

here is a link of other users having wrong date problems after upgrading to 10.6
http://discussions.apple.com/thread.jspa?threadID=2134525
Some people have managed to fix their date problems. The easiest workaround is to add the column "Date Sent" under (View->Columns->Date Sent) in mail.app and to sort by the send date not the received date.
Hope this helps

Cisco Switch connecting to Radius Server

Hello Team,
I discovered that anytime the Uplink of my Cisco C2960CG-8TC-L goes down and reconnects, before the switch connects with the Radius Server, the access ports starts to connect into Guest VLAN, which is not the correct production VLAN that has been assigned to the Mac addresses.
I thought I could resolve this with Link state track Upstream and Downstream, but it's not working effectively.
The solution to the problem should be when the UPLINK port does down for whatsoever reason and comes back up, it should communicate with the Radius Server first, thereafter the access ports comes up and connect to the assigned Production VLAN not the Guest VLAN.
How do I achieve this? Any positive advise would be highly appreciated. Configuration can be uploaded if needed.
Thanks
Peter

I haven't ever done it, but I think you can set up the Access point as a radius server. Then configure Mac authentication and either filter with the local list or an access list.
Thanks,
Alex

Please help: Photoshop CS5 - Yosemite locked permissions?

Please I hope someone can help!
I just updated my older iMac with Yosemite, and reinstalled Adobe CS 5. What a mess. Neither Illustrator or InDesign will launch. Photoshop will work, but has problems. (Thank God I've not touched my newer, main studio working iMac's OS, where CS5 still runs fine.)
In trying to quit Photoshop (which won't respond to quitting and must be force-quit), I am getting the error message, "Could not save Preferences because the file is locked or you do not have necessary access privileges. Use the 'Get Info' command in the Finder to unlock the file or change permissions on the file of enclosing folders."
I searched around and found what was sure to be a promising fix posted some time ago (see below, "Here's the Fix"), but the problem is, when I hold down Option > Go ... Library to navigate to the "Adobe Photoshop CS5 Settings", the damned folder is actually EMPTY! There is no file to click on in order to get info on it! So I cannot even tamper with permissions. Ugh. It's bad enough the neither Illustrator nor InDesign will launch. What a sorry mess. I will not TOUCH my MacBook Pro laptop or main iMac. I will leave well enough alone. So glad I only messed with this one computer I rarely do anything on anymore. It could be that this is an old early 2009 iMac, sure, but I don't trust the new OS.
Anyone encounter similar, and have any workaround? Thank you in advance!
HERE'S THE FIX:
Navigate to /Users/YOURUSERNAME/Library/Preferences/Adobe Photoshop CS5 Settings
Select that file File>Get Info
At the very bottom under permissions, hit the + icon.
Add your user name from the list that pops up.
Highlight the user just added.
Click the gear icon to the right of the +/-
Choose make owner.
Click the gear icon again and choose apply to folder contents.
Open Photoshop.
That should do the trick!

Have you tried saving as another layer-capable format, tif or psb?
Is there anything notable about the files – extraordinary number of layers, size or whatever?
Other than that have you performed the usual trouble-shooting routines (trashing prefs by keeping command-alt-shift pressed while starting Photoshop, 3rd party plug-ins deactivation, system maintenance, font validation, etc.)?

I have locked my macbook pro through icloud and now it needs 4 digit pin code please help me ., I have locked my macbook pro through icloud and now it needs 4 digit pin code please help me .

i have locked my macbook pro 10.7 through i cloud and now it needs 4 digit pin as a password.pls help me to open the macbook with password.

You just input the 4-digit PIN that you were given when you locked your machine over iCloud.
Pretty simple - unless you don't recall the PIN.
Clinton

PLEASE HELP! Just switched to Mac and I have a few questions about bootcamp

I am looking to load Boot Camp onto my MacBook and want to know if it is necessary to save things like songs to an external hard drive(the computer is new so i don't have any important documents or files on it).
Second Question: I would consider myself somewhat of an intermediate user on the PC operating system but I am new to Mac and want to know if I should run Boot Camp on my own knowing just the basics of Mac.
Thanks for any help,
-Cody
Florida

If you have nothing important, don't worry. If you want to save the songs to an external hard drive do so. The key is being aware that you could lose everything, so you should back up anything and everything you don't want to lose. If you can't afford to lose the songs, back them up somewhere. If it were me, I would back up the entire computer, just in case, but that's me. Just be sure to unplug the external hard drive before commencing the Windows installation.
As for running Boot Camp on your own, I don't see why not. Most of the problems people have is not with Boot Camp per se but with the installation of Windows. In particular, take care to not overwrite or break your Leopard installation by selecting the wrong disk partition to install Windows on, and make sure you then format (or quick format) the Boot Camp partition to FAT or NTFS. Do not choose the "convert to NTFS" option!

HT1212 Please help me - Backup Passcode Locked - Need to restore

Im trying to restore my old iphone with my new one. Old phone is off and backed up to icloud and computer. When i plug in the new phone to itunes, it has this error message: Cannot connect to iphone . It is locked with a passcode. If i do not remember anything about inputting a passcode for my backup, is there a way to recover my password? Or another way to restore my new iphone with the data on the computer w/o the "backup passcode"?

Your question is not quite clear... Try here...
See iTunes and encrypted backups here
http://support.apple.com/kb/HT4946
If it is a Pass Code lock...
Connect to iTunes on the computer you usually Sync with and “ Restore “...
http://support.apple.com/kb/HT1414
If necessary Place the Device into Recovery mode...
http://support.apple.com/kb/HT1808

Please help me to choose the right Windows Server 2012 edition

Dear All,
I will plan for new hardware for a University. I plan to have Windows Server 2012 network with upto 10,000 users. I will have Exchange, SharePoint and SQL Server as well.
Please advice on what Windows Edition I should select as well as # of CAL to be purchased.
I am expecting to have a Server of 32GB of RAM, 12TB of hard disk. I will take advantage of HyperV to setup Database server, sharePoint and Exchange
Thank

For the CALs, you can read about them there: http://blogs.technet.com/b/volume-licensing/archive/2014/03/10/licensing-how-to-when-do-i-need-a-client-access-license-cal.aspx
For the Windows Server 2012 edition to use when involving virtualisation, you can read about that here: http://download.microsoft.com/download/7%2F7%2F0%2F7707E736-4557-4310-9709-87358F7E6D1A/WindowsServer2012VirtualTech_VLBrief.pdf
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

Please help urgently Failed to deserialize statedump from server in Cluster

Dear All,
Appreciate a help on this urgently..... I am new to weblogic server & this technologies ... we created IPM,UCM,SOA clusters on one domain (my_domain), all the servers of all the clusters in 1st machine started .... but IPM server is not starting on the 2nd machine (other servers - SOA and UCM started on the 2nd machine)
I am getting the following error. could anyone help to solve this problem...
####<Jan 20, 2011 9:37:29 PM IST> <Info> <Cluster> <machine2.domain.com> <IPM_server2> <[STANDBY] ExecuteThread: '3' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1295539649529> <BEA-000128> <Updating -2575471700288226143S:10.1.7.1:[16000,16000,-1,-1,-1,-1,-1]:my_domain:IPM_server1 in the cluster.>
####<Jan 20, 2011 9:37:29 PM IST> <Error> <Cluster> <machine2.domain.com> <IPM_server2> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1295539649554> <BEA-000140> <Failed to deserialize statedump from server -2575471700288226143S:10.1.7.1:[16000,16000,-1,-1,-1,-1,-1]:my_domain:IPM_server1 with java.lang.ClassNotFoundException: oracle.imaging.input.inputagent.InputAgent.
java.lang.ClassNotFoundException: oracle.imaging.input.inputagent.InputAgent
at weblogic.application.internal.AppClassLoaderManagerImpl.loadApplicationClass(AppClassLoaderManagerImpl.java:135)
at weblogic.common.internal.ProxyClassResolver.resolveProxyClass(ProxyClassResolver.java:68)
at weblogic.common.internal.WLObjectInputStream.resolveProxyClass(WLObjectInputStream.java:76)
at java.io.ObjectInputStream.readProxyDesc(ObjectInputStream.java:1531)
at java.io.ObjectInputStream.readClassDesc(ObjectInputStream.java:1493)
at java.io.ObjectInputStream.readOrdinaryObject(ObjectInputStream.java:1732)
at java.io.ObjectInputStream.readObject0(ObjectInputStream.java:1329)
at java.io.ObjectInputStream.defaultReadFields(ObjectInputStream.java:1947)
at java.io.ObjectInputStream.readSerialData(ObjectInputStream.java:1871)
at java.io.ObjectInputStream.readOrdinaryObject(ObjectInputStream.java:1753)
at java.io.ObjectInputStream.readObject0(ObjectInputStream.java:1329)
at java.io.ObjectInputStream.readObject(ObjectInputStream.java:351)
at weblogic.common.internal.WLObjectInputStream.readObjectWL(WLObjectInputStream.java:98)
at weblogic.cluster.BasicServiceOffer.readExternal(BasicServiceOffer.java:172)
at java.io.ObjectInputStream.readExternalData(ObjectInputStream.java:1792)
at java.io.ObjectInputStream.readOrdinaryObject(ObjectInputStream.java:1751)
at java.io.ObjectInputStream.readObject0(ObjectInputStream.java:1329)
at java.io.ObjectInputStream.readObject(ObjectInputStream.java:351)
at java.util.ArrayList.readObject(ArrayList.java:593)
at sun.reflect.GeneratedMethodAccessor3.invoke(Unknown Source)
at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
at java.lang.reflect.Method.invoke(Method.java:597)
at java.io.ObjectStreamClass.invokeReadObject(ObjectStreamClass.java:974)
at java.io.ObjectInputStream.readSerialData(ObjectInputStream.java:1849)
at java.io.ObjectInputStream.readOrdinaryObject(ObjectInputStream.java:1753)
at java.io.ObjectInputStream.readObject0(ObjectInputStream.java:1329)
at java.io.ObjectInputStream.readObject(ObjectInputStream.java:351)
at weblogic.common.internal.WLObjectInputStream.readArrayList(WLObjectInputStream.java:116)
at weblogic.cluster.StateDumpMessage.readExternal(StateDumpMessage.java:53)
at java.io.ObjectInputStream.readExternalData(ObjectInputStream.java:1792)
when I check the error number BEA-000140, it says
Cause - Server failed to deserialize object since it does not have the class definition. This usually happens if your application classes are not deployed on all the nodes in the cluster. It is preferable to deploy beans to all the nodes of the cluster.
Action - Make sure all the classes are available on all the nodes of the cluster.
Could any one give steps as how to do this or the solution to this problem.... I am new to weblogic..
Thanks in advance.
Edited by: user599937 on Jan 20, 2011 8:32 AM
Edited by: user599937 on Jan 20, 2011 8:37 AM

This is definitely the problem:
java.lang.ClassNotFoundException: oracle.imaging.input.inputagent.InputAgent
The cause is likely that the configuration during installation of IPM went wrong somehow or the particular way you are starting the server is missing the IPM libraries. This is not so much a WebLogic Server issue as an IPM issue. I recommend you try posting in one of the Content Mgmt forums like WebCenter Content or open a support case with the IPM team.

Please, HELP ME... "ZENworks Repoting Server installation f"

(Sorry was mistake send to the Politic forum)
Server:
#cat /proc/version
Linux version 2.6.16.60-0.42.5-smp (geeko@buildhost) (gcc version 4.1.2 20070115 (SUSE Linux)) #1 SMP Mon Aug 24 09:41:41 UTC 2009
# uname -a
Linux zcm0 2.6.16.60-0.42.5-smp #1 SMP Mon Aug 24 09:41:41 UTC 2009 x86_64 x86_64 x86_64 GNU/Linux
# rpm -qa | grep -i zenwork
novell-zenworks-java-links-1.5.0_11-1
novell-zenworks-addon-image-langs-server-10.2.1-33465
novell-zenworks-configure-server-10.2.1.34436-34436
novell-zenworks-inventory-server-10.2.1-33465
novell-zenworks-policies-langs-server-10.2.1-33465
novell-zenworks-reports-server-10.2.1-34436
novell-zenworks-uninstall-10.2.1-33465
novell-zenworks-zmgexplorer-10.2.1-32627
novell-zenworks-znews-server-10.2.1-33465
novell-zenworks-bundles-langs-server-10.2.1-33465
novell-zenworks-discovery-langs-server-10.2.1-33465
novell-zenworks-managed-devices-langs-server-10.2.1-33465
novell-zenworks-primary-agent-10.2.1-31704
novell-zenworks-temp-extras-server-10.2.1-34617
novell-zenworks-zencore-agent-10.2.1-31891
novell-zenworks-zmgpxeclientfiles-10.2.1-32627
novell-zenworks-actions-10.2.1-30006
novell-zenworks-asset-management-langs-server-10.2.1-33465
novell-zenworks-certificate-authority-server-10.2.1-33465
novell-zenworks-core-server-10.2.1-34693
novell-zenworks-deployment-server-10.2.1-34693
novell-zenworks-java-utilities-server-10.2.1-33465
novell-zenworks-patch-management-10.2.1-1000
novell-zenworks-preboot-langs-server-10.2.1-33465
novell-zenworks-remote-management-server-10.2.1-33465
novell-zenworks-system-update-10.2.1.5432-32066
novell-zenworks-temp-extras-langs-server-10.2.1-33465
novell-zenworks-xplat-pre-agent-10.2.1-32192
novell-zenworks-zmediacreator-10.2.1-32627
novell-zenworks-zmgservices-10.2.1-32627
novell-zenworks-zmgupdate-10.2.1-32627
novell-zenworks-version-10.2.1-34731
novell-zenworks-jsvc-5.5.20-1
novell-zenworks-common-libs-10.2.0-21306
novell-zenworks-addon-image-server-10.2.1-33465
novell-zenworks-bundle-10.2.1-31873
novell-zenworks-certificate-authority-langs-server-10.2.1-33465
novell-zenworks-core-langs-server-10.2.1-33465
novell-zenworks-deployment-langs-server-10.2.1-33465
novell-zenworks-java-utilities-langs-server-10.2.1-33465
novell-zenworks-policies-server-10.2.1-33465
novell-zenworks-zcm-server-10.2.1-33465
novell-zenworks-preboot-server-10.2.1-33465
novell-zenworks-remote-management-langs-server-10.2.1-33465
novell-zenworks-system-update-server-10.2.1-34646
novell-zenworks-thirdpartyimagingutils-10.2.1-32627
novell-zenworks-zmgbootcd-10.2.1-32627
novell-zenworks-zmgmcast-10.2.1-32627
novell-zenworks-zmgweb-10.2.1-32627
novell-zenworks-tomcat-5.5.23-11
novell-zenworks-common-jars-10.2.0.22715-22715
novell-zenworks-bundles-server-10.2.1-33465
novell-zenworks-discovery-server-10.2.1-33465
novell-zenworks-managed-devices-server-10.2.1-33465
novell-zenworks-pre_pkg-10.2.1-33465
novell-zenworks-system-update-langs-server-10.2.1-33465
novell-zenworks-zcm-langs-server-10.2.1-33465
novell-zenworks-zmgpolicy-10.2.1-32627
novell-zenworks-asset-management-server-10.2.1-33465
novell-zenworks-configure-langs-server-10.2.1-33465
novell-zenworks-inventory-langs-server-10.2.1-33465
novell-zenworks-policy-10.2.1-27420
novell-zenworks-reports-langs-server-10.2.1-33465
novell-zenworks-version-primary-server-10.2.1-34693
novell-zenworks-zmglibs-10.2.1-32627
novell-zenworks-znews-langs-server-10.2.1-33465
THis was my steps:
1 copy from the ZRM10.2.1 to the /usr/local/src/zrm
2) cd /usr/local/src/zrm
3) setup.sh
Administrator / qwerty
Zenworks Reporting Server Already Installed in this ZONE
"ZENworks 10.1.0 Reporing Server haz already been installed in this zone.
Do you want to decommission it from the then ?"
OK
BOE XI 3.1 Installation is is progress...
ZENworks service must be restarted in order to use ZENworks Reporting Server.
(*) No, I will restart the services mysel | Next
And see this error:
Installation Resullts:
ZENworks Repoting Server installation failed
Press: Done
After all this steps:
shutdown -r now
from the my Linux do:
https://myzcmserver | Reports
And see this info:
"Note: There is no ZENworks Reporting Server configured in the Management Zone."
What can i do ?
Serg

amaltsev1,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

Please help : "Configuring Windows SSO for Sun portal server 7.1"

Hello friends,
I have a problem when create Single Sign On ( SSO ) on the portal server 7.0
If you have configured successfully.Please give me the way you have used.
Thank you very much.
DungT
Related document and information :
http://docs.sun.com/app/docs/doc/819-4670/6n6qardtu?a=view#gbaqc
http://forum.java.sun.com/thread.jspa?threadID=5140689&messageID=9519196
Edited by: dungtran on Mar 13, 2008 4:35 AM

There is a ZIP Install available for Windows that bundles the Access Manager, Directory Server,and Portal Server in a pre-configured deployment. Try this download instead:
PS 7.1u1
[https://cds.sun.com/is-bin/INTERSHOP.enfinity/WFS/CDS-CDS_SMI-Site/en_us/-/USD/ViewProductDetail-Start?ProductRef=PortalSvr7.1U1-OTH-G-F@CDS-CDS_SMI]
PS 7.2
[https://cds.sun.com/is-bin/INTERSHOP.enfinity/WFS/CDS-CDS_SMI-Site/en_US/-/USD/ViewProductDetail-Start?ProductRef=PortalSvr7.2-OTH-G-F@CDS-CDS_SMI]
- Jim

Please Help: 3550 lab switch locked by radius server

Similar Messages

Maybe you are looking for