Please help : N82 Formatting tool

Dear friend, this is vijay from india. I have something different issue. My phone memory showing full memory utlised. and preventing me to SMS, Saving contacts or any thing. I tried *#7370#, but still problem is same. I had gone to nokia care service centre but they asked me very high amount. I am unable to bear this. Could you please tell me how could i format my handset ?? is there any tool available and after formatting how will i upload new os (means booting and installation).. please help

You could try the deep reset.
Always remember to backup your phone before performing resets as your data will be lost.
Then try the "3 finger deep reset". With the phone powered off, depress and hold these three keys simultaneously "*" "3" "green phone" and then power on phone using the on/off button whilst keeping the three keys depressed until you hear start-up tone.

Similar Messages

Please Help N82 Dead!

Hello everybody
this is my first post here.so im extremely sorry if this is the wrong section.
i purchased the nokia n82 in india around January 2008.last week when i decided to connect the phone to my pc and update it using nokia software updater to the latest version...it was running all fine suddenly "NSU" said that the connection to the phone was lost and remove and insert battery again... i did it as many times possible den some sites indicated the three finger salute.. i tried that also but no use..all i have is a black screen with a backlight on which vibrates when switched on.
then i took it to the nokia care in Bangalore(RT nagar) the place is called shilak.The phone is under warranty so i thot nokia care would help.. first time i went there the incharge there took my phone looked at and said to me you hav dropped your phone and u hav damaged ur screen.. there are a few scratches on the phone due to a bit ruf use.. then he took the phone sayin warranty was void and i had to pay for the services.. there was no feedback from them.then i went back to the place 2 days later... the lady in the counter said "its board problem we hav no solution for it".. then i went to the dealer i bought the phone from..he said hell giv a try with the nokia care...i went two days later... now the reason given by nokia care for waranty being void is water logging...i was like omg!! i hav never even brought the phone near water..
people please help me.. as i really doubt whether nokia care in bangalore or india will help me repair my phone.. for a mere 400rs or 10$ they are ruining nokias name..

Sorry to read about your disgraceful treatment and the hands of nokia vinaydas.I'm afraid that these FAKE voiding of warranties are becoming more and more common.Nokia stop caring after they have your money.My advice to you would be to seek legal advice or some offical goverment body such as trading standards.Maybe even search here and other forums find others in the same position as yourself and get them to support you in a joint claim against nokia.This has to stop its nokia cannot be allowed to get away with this.I have a thread on here named QUALITY CONTROL AND AFTER CARE please add your voice to it.

Please help on Format Mask...

Hi everyone,
I have few question regarding to Format Mask:
1) I know that if u key-in the invalid format
(ie: format: dd-mm-yyyy and I key-in 35/21/2001_
Oracle will display the error message at the Status bar of the
Form, can I make this error message to displayed as a popup
msg (like alert) automatically? Or I need to do a checking on
the error code in ON-ERROR trigger than SHOW_ALERT()?
2) How to make a Format Mask that will format this:
60312345678 format to (603)1234-5678
6031234567 format to (603)1234-567
I tried this format mask "("999")"999"-"999, it worked for the
first one but the second one it came out as below:
6031234567 formated to (60)3123-4567
Is there a way to overcome this?
Thank You
Regards
Wai Chong

1.I ussually use on-error trigger at form level and check for
the error code and use show_alert built in accordingly.
2.Have you tried adding, if I am not mistaken, FM (fill) mode.
It will theoretically accept anything that you type. You can
look on the builder help on format mask topic. Or have you
tried adding the space after the region code. This is pure
speculation but you might want to try.
Hope it help.

Java Experts please help - SimpleDateFormat.format reduces date by a day !!

Hi,
I am facing a very weird problem with SimpleDateFormat class. The input Date to SimpleDateFormat.format method is getting reduced by ONE DAY. This problem is happening at random and is not reproducible at will. Any help/pointers to resolve this issue is very much appreciated !!.
Code is similar to the following code lines
input = "2003-11-01 00:00:00.000000000";
output = 31-Oct-2003 (strange !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!)
import java.sql.Connection;
import java.sql.SQLException;
import java.sql.Timestamp;
import java.text.DateFormatSymbols;
import java.text.ParseException;
import java.text.SimpleDateFormat;
import java.util.Date;
import java.util.Hashtable;
import java.util.Locale;
import java.util.TimeZone;
import java.util.SimpleTimeZone;
public class DateTester {
/** Default constructor for Util.
public DateTester() {
private static String replace(String pattern, String from, String to) {
return replace(pattern, from, to, null);
private static String replace(String pattern, String from, String to, String notFrom) {
StringBuffer sb = new StringBuffer();
boolean finished = false;
int index = pattern.indexOf(from);
if (index < 0) return pattern;
do {
if (notFrom == null ||
notFrom.length() + index > pattern.length() ||
!pattern.substring(index, index + notFrom.length()).equals(notFrom)) {
sb.append(pattern.substring(0, index));
sb.append(to);
sb.append(pattern.substring(index + from.length()));
finished = true;
} else index = pattern.indexOf(from, index + from.length());
while (!finished && index >= 0);
if (!finished) return pattern;
return sb.toString();
public static void main(String[] argv) {
String pattern = "DD-MON-YYYY";
System.out.println("original pattern =" + pattern);
pattern = replace(pattern, "FM", "");
pattern = replace(pattern, "AD", "G");
pattern = replace(pattern, "A.D.", "G");
pattern = replace(pattern, "BC", "G");
pattern = replace(pattern, "B.C.", "G");
pattern = replace(pattern, "AM", "a");
pattern = replace(pattern, "A.M.", "a");
pattern = replace(pattern, "PM", "a");
pattern = replace(pattern, "P.M.", "a");
pattern = pattern.replace('\"', '\t');
pattern = pattern.replace('\'', '\"');
pattern = pattern.replace('\t', '\'');
pattern = replace(pattern, "DDD", "DDD");
pattern = replace(pattern, "DAY", "dd");
pattern = replace(pattern, "DD", "dd", "DDD");
pattern = replace(pattern, "HH24", "HH");
pattern = replace(pattern, "HH12", "KK");
pattern = replace(pattern, "IW", "ww");
pattern = replace(pattern, "MI", "mm");
pattern = replace(pattern, "MM", "MM", "MMM");
pattern = replace(pattern, "MONTH", "MMMMM");
pattern = replace(pattern, "MON", "MMM");
pattern = replace(pattern, "SS", "ss");
pattern = replace(pattern, "WW", "ww");
pattern = replace(pattern, "W", "W");
pattern = replace(pattern, "YYYY", "yyyy");
pattern = replace(pattern, "YYY", "yyy");
pattern = replace(pattern, "YY", "yy");
pattern = replace(pattern, "Y", "y");
pattern = replace(pattern, "RRRR", "yyyy");
pattern = replace(pattern, "RRR", "yyy");
pattern = replace(pattern, "RR", "yy");
pattern = replace(pattern, "R", "y");
System.out.println("converted pattern =" + pattern);
String origDate = "2003-11-01 00:00:00.000000000";
System.out.println("original date =" + origDate);
Timestamp origTimeStamp = Timestamp.valueOf(origDate);
SimpleDateFormat sdf = new SimpleDateFormat(pattern, Locale.getDefault());
sdf.setLenient(false);
String formattedDate = sdf.format((Date) origTimeStamp);
System.out.println("formatted date =" + formattedDate);
Thanks a lot for your time !

Your code is too hard to read for me to look at it in great detail. When you post code, please use [code] and [/code] tags as described in Formatting Help on the message entry page. It makes it much easier to read.
However, I'm guessing it's a TimeZone issue. The midnight on 11/1 that you're setting is probably getting converted to GMT somewhere before the Date object is created. If you're in the U.S., then that's afternoon or evening on 10/31.
Try:
* Starting with a time that's later in the day on 11/1.
* Formatting your date to include time and timezone when you print it. (Just for testing--you can put it back once you understand what's going on
* Reading the Calendar, Timzone, Date, etc. APIs closely.
* Reading any tutorials or texts you can find on the subject.
* Writing a bunch of very small and simple tests to get an understanding of how this all fits together.
Date/Time/TZ handling in Java is kinda tricky.

Please help me format my ipod

I tried to re-install the software for my ipod and had been told my ipod need to be formatted. I click format button. It came up the message " assertion b failed at. /ipod format FAT 32. cpp appline 1068". Anybody can tell me what I am going to do? Thanks a lot!
Windows ME

Thank you for quick response,but what's OS and where I can get it? I checked the user guide p4, still didn't get it. BEW, I use my ipod with a window PC. Can you tell me more. thanks

Please help with formatting a document

Here's what I am trying to do:
Create a quiz. The top of the quiz has a set of instructions. Just below the instructions, is question number 1. The number "1." lines up on the left with the left margin of the instructional paragraph. The question text should then have a left margin that is indented 0.5inch and the text will continue to be indented the same 0.5 inch (a hanging indent).
Also, the text of the question will be single space, but the space between the questions will be double space.
When I try this with a single space setting, I get the numbered list -- which is fine -- but when I hit the return key again in order to get double spacing between the questions, I lose the number.
Thanks and if you need any clarification, feel free to ask.
Boris

Yvan,
I appreciate your input, but beg to differ. I have downloaded the user manual in PDF and have been using it to trouble shoot this issue. I find that in this particular instance, it has not been as helpful as I would like.
I prefer to use the manual as a reference, and while reading it from start to finish is probably a good way to gain an in depth understanding of the program, that act can also lead to information overload, and, hence, an inability to recall exactly what it was that would help solve a particular issue.
I find that in technical manuals, different perspectives in presentation and organization will resonate better with one reader and less so with another. It seems to me that a collection of these perspectives is often more helpful than a single resource.
Regards,
Boris

Please help in Format

Hello,
How do I format a number, e.g. 12345 to become " 12345"?
Many thanks!

" 12345" i think u want to convert it into string. than use this
int i=12345;
String strInt=new String(i);
strInt=" "+strInt;
[\code]

N82 Completely Crash, Please HELP!!

Hi everyone,
My N82 is completely crash and I do not know how to fix.
I never dropped this phone and never used messily. Because I love this phone since I got it.
I tried all possibility to fix.
To take out SIM and SD. To reinstall the firmware.
I guess it started after I installed new firmware v20.
Here are my problem
1. while calling, the phone suddenly freeze and cut a communication. It also happens many times when I hang up the phone call. After a moment it turns off.
2. When I turn on the phone, it just show black screen and keep turn on a backlight.
3.When I remove the SD, sometimes it turns on correctly but few hours later, it shows black screen and backlight.
4.When I charge the phone, it also shows black screen and backlight.
I hope this is software problem because I am using it in Japan and Japanese customer center doesn't support this model.
SOMEONE PLEASE HELP!

Try a hard reset, but backup everything you want to keep. Also remove the memory card before you do it and try it without the card to see if it works. If it does work you may need to format the memory card to avoid any slowdown.
Hard reset:
1. Switch off the phone.
2. Hold down the following three buttons: Green (the call answer button), * button, and '3' button.
3. While holding these buttons, press the power button and switch on the phone.
4. Release when the phone shows the nokia logo or shows other signs of life like the language selection screen.

Please HELP! = major disk issue - none of OSX "help" tools works (repair/time machine/reinstall)

Hello to all,
My first post, but directly with a very difficult case I suddenly encountered yesterday evening...
When, as usually I opened the lid, it turned on from sleep, as usually, however frozen suddenly... so I did hard turn off... with ON/OFF button. When it turned on again, I had no possibility to put my password, but I was directly faced with "OSX tools" with 4 options (it is in Polish so I try the translation):
1) Recover from Time Machine back up;
2) Install OSX again;
3) Get online help;
4) Disk tool;
I am totally ****** off how this could happen. There was so much stuff on the disk, including the whole Aperture libary with thousends of my daughter photos (she was born a year ago) - priceless stuff.
I would never expect Apple to give me such an "experience"... never heppened to me on any PC's before..
I have 2011 MacBook Pro 13" with Maverics.
This is what I encountered using each of solutions:
1) I use Synology DS209 for Time Machine backup (connected via Lan cable). As far as I remember backup is about 2 months old. Anyway when I choose this option. OSX tool finds the Time Machine in DiskStation, connects to "MacBook Pro" timemachine on the external disk, BUT cannot find any BACKUP further on!!!! I am lost!
2) second, but not preferred option is OSX reinstallation.After initial analysis, and conditions acceptance, I cannot choose the only disk available. I can see only "recovery disk", but when I click on it, there is a message popping up "This disk is blocked". Obviously this prevents any further activities in reinstallation;
3) Third option is BS clearly, no help at all.
4) Disk tool shows me several disks / I am not an expert, so I am not sure how to understand it (Bold is active, standard non active):
- 320,07 GB Hitach HTS54503...
- Macintosh HD
- Superdrive
- disk1
- OS X Base System
I run "check disk" for Hitachi. No problems. Nothing to repair.
I run "check disk" for Macintosh HD => This disk requires repair. So I run "repair". Quickly I get a message "Disk Tool is unable to repair this disk. Please backup as much data as possible, format the disk and recover the files from backup"..... Really????? How can I backup any files???
DEAR COMMUNITY, please HELP!
What to do in order not to loose any data on one hand and on the other be able to use the computer again?
Please note I do not use "recovery CD" all is running without anything in CD/DVD drive.
Thanks in advance for your answers, competence and experience!
Disk tool does not give any solution, showing

You are in a bad situation, because the internal drive has malfunctioned and your only backup is on a device that is not suitable for use with Time Machine, despite what its manufacturer says.
You must try to make another backup now, before you do anything else. It may or may not be possible.
There are several ways to back up a Mac that is not fully functional. You need an external hard drive to hold the backup data.
1. Boot from the Recovery partition or from a local Time Machine backup volume (option key at startup.) Launch Disk Utility and follow the instructions in this support article, under “Instructions for backing up to an external hard disk via Disk Utility.”
2. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode. Use the working Mac to copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
3. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.

My pages is showing error while opening a document in microsoft word format. Please help

While trying to open documents in microsoft word format, pages is showing an error. It is unable to complete the task and is requesting me to reopen pages but then no response. However I am able to work on pages format. Please help.
thanks

When you open a Word document in Pages, it is translated into the internal .pages document format — and you are no longer working in the original Word document format. This translation also occurs in reverse when exporting a document back to Word. When you open a Word document in Pages, if it has issues with the translation (missing font characteristics, other issues), it will open a warning dialog box and display these issues for you.
If however, you prefer to always work in the native Word document format, and not risk translation issues, then you should be using MS Word in Office for Mac 2011 with the latest update.

Photoshop Elements 8. "Could not use Clone Stamp Tool because of a program error." Please help.

Photoshop Elements 8. "Could not use Clone Stamp Tool because of a program error." Please help.

Try this:
Open your picture file
Access the clone stamp tool
Hold down the ALT key on the keyboard and left click on the area from which you wish to clone, then release the ALT key, and click to place the pixels at the destination
TIPS:
It is a good idea to open a blank layer at the top in the layers palette, and do the cloning on this layer. Be sure that "sample all layers" at the top is checked. You can change the layer opacity if necessary
Use the bracket keys next to the letter p on the keyboard to increase & decrease the size of the cursor
Let us know how you make out with the error message now.

Photoshop CC text tool problem! Please HELP!

Everytime i try to use the text tool on photoshop CC it turn my picture black and keep flashing on and off.! Can someone please help me solve this problem? ( Please excuse my english, I'm still learning ^^")

Windows 8? Update your video card driver from the GPU maker's website.

I just bought a 7th gen Nano, no matter what I try, it will not let me load videos to it, I downloaded 5 off Itunes, it still tells me they wont play on my ipod, ive tried to convert them to every type of format possible, please help me

I have tried everything I can try, I figured downloading them from Itunes they would go straight onto my Nano, but it wont let me put any of them on there, I cannot find anything anywhere on the internet, nothing, I am so furious, I have converted them to any and every possible format, and this fking thing will not load one of them, so before I finally lose it(my temper) and destroy my brand new Nano, can someone please please help me, I am generally pretty well versed in this kind of stuff, and can figure things out, but nothing I do will let me do anything, I am stuck, and this is not acceptable, and will possibly be the last time I purchase anything other then a desktop from Apple, they are not making things easier and more convienent, they are making things harder and more monotonous, can somebody please point me to what im doing, or not doing? thank youj

In iTunes, do Store->View my AppleID
Click "Deuthorize ALL"
Then, on any computers you still have, do Store->Authorize this computer. If there are less than 5, you will have no problem.
You can only do "deauthorize all" once a year, so in the future, if you ever throw a computer away, remember do to "Store->Deauthorize this computer" first.

5th Gen iPod error while formating please help

Ok here is the long and complicated story. I had a iPod Mini 4GB and thought it was time to upgrade to a 30GB. itunes and everything working just fine up to the point where I went and loaded the ipod disc to format my new iPod. I incountered a iPodDeviceInternal assert error when the program started to format the iPod and failed to complete the install. I tried over and over again. I loaded itunes and it said that the iPod could not be Recognized and that i should reinstall itunes. I then went to Best Buy were I bought it and took it to the Geek Squad tech. center and he hooked it up and it worked fine,then telling me to try downloading the newest version of itunes. I did and it installed fine...but when i click it, it doesnt open. so baically I cant get itunes to open and my iPod will not format. Please Help me

Can you see iPod drive under Removable disk in My Computer?
If so,try disk defragment on it or manually format your iPod and lastly redo the whole installation process

"It is formatted incorrectly, or is not a format that iBooks can open". Can anyone help me with this message of a book that I purchased on iBooks, read, highlighted in the book and now I can't open it anymore. Please help!!!

"It is formatted incorrectly, or is not a format that iBooks can open". Can anyone help me with this message of a book that I purchased on iBooks, read, highlighted in the book and now I can't open it anymore. Please help!!!

Mine does the same thing occasionally, is your phone jailbroken? Sometimes it will work if you delete the book and reinstall it or put your phone into airplane mode then turn it back off.

Please help : N82 Formatting tool

Similar Messages

Maybe you are looking for