PLEASE HELP! Restarting issue with K8N SLI. need bios help???

Hi people,
I would really appreciate some help this this problem im having. It’s a bit long winded but ill try to keep it short.
My pcs spec is as follows –
MSI K8N SLI (model MS-7185) motherboard
AMD Athlon X2 64bit 4200+ cpu
4 x 512mb ram
Running with a Radeon X700 256mb graphics card.
Ever since I purchased the machine ive been having problems with the pc loading up XP (or any OS for that matter!). Sometimes it would freeze on the loading screen and sometimes it would freeze on the black screen just after the loading screen. Sometimes while running windows perfectly normally, a blue screen with writing describing the error came up and then the system restarted, however, I would only ever manage to read the title of the blue screen as the pc restarted so quickly. I remember seeing the word hardware though, so I guessed it was a serious hardware issue. I lived with this for a few months thinking it might be something im doing that’s making it be so unreliable, such as a software issue, but I recently went on a mission to sort it out. The BIOS of the motherboard was password protected and I wasn’t aware of this until I had lost contact with who I had bought the system off, so I decided to restart the motherboard’s settings by pressing the reset button on the board itself. Next time I booted it up it told me that the defaults were restored etc and continued to boot windows, however now I can hardly get windows to start at all, the system restarts on the loading screen 8 times out of 10, and if it does boot up fully then it doesn’t last long before crashing on me. I messed about with a few of the BIOS settings, but to be honest I have no experience with working with these settings, its all very new to me. I have an idea that it could be the processor or the graphics card causing the problem, just an inkling though!
If anyone can help me I would appreciate it greatly. Thank you. Adam
you can also email me at e-mail - [removed by moderator due security purpose]

Quote from: Grayone on 23-December-06, 06:36:43
Can you furnish us some additional info on the 4 sticks of memory that you have? Also on the power supply? There is a label on the side of it that lists the manufacturer of the power supply and the amperage output for the 12volt power rail.
Thanks for your reply. here is some more info:
4 x Kingston 512mb model no - KVR400X64 C34
The power supply is a Sweex Advanced Gold 650W [BA000110]. max currennt on 12v rail is 25A
Hope this helps. Thanks again for your reply.

Similar Messages

Hi, can anyone help me out with this, I need some help on designing GUI for e-learning coursewares. Some tutorials or some helpful sites will do.

I need some help with the GUI design.

Have you tried the line inputs on the back of your FirePod? If you update its firmware (not sure if you will need to or not), I seem to remember hearing that the FirePod can run without FW connection, i.e. stand alone. In this mode with the outs from your mixer into line ins 1-2 (2nd from left on the back) it should work fine. I say should because I have never tried. However, these are used for returns from an external effects unit. I assume here, and the important word is assume, that there are two so that they can be used as a stereo send or as a mono send. Worth a try! Let us know how it goes.
Best, Fred

Issue with shared services - Need Urgent Help please!!

Hello Experts
One of my customer has installed a new instance of oracle and copied all the schemas and data over to the new instance.
Now when they bring up shared services, have lost all our provisioning. None of the projects are recognized by shared serices and gets the following error when we try to bring up a user
'xxxxx' is not a recognized Shared Services project. Please contact your adminstrator
Is there something we need to do to restore Shared Services to its original state?
Thanks in advance.
Regards,
Sonu
Edited by: 637223 on Jan 20, 2009 2:19 AM

hi,
I doubt that "creating a new instance of oracle and copied all the schemas and data over to the new instance" will register the project with shared service and thats why giving error. Because when you install shared service, it asks you about the database name (oracle in your case) to register with. So even if you overwrite that database by new instance it gives error.
Have you tried the configuration utilty ? Over there you can provide the new database instanse as your database and configure your shared service. Remember that you need to do a complete configuration of shared service , analytic administration services and analytic services. After configuring, Restart the system.....it should work.
Hope this helps!
Regards,
James

Memory issues with K8N Sli

I run this mostly as a high end gaming rig and am not really into OCing. I currently have:
Corsair CMX512-2700LLPT 512MB DDR333 XMS2700 64Mx64 184 DIMM CAS2 32Mx8 DRAMs Low Latency SPD Memory w/Platinum Heat Spreader Retail
Is this fine?
But it seems to be running at single channel 64mhz (which I can't figure out)? An suggestions on what to do here?
If I were to buy some new memory what memory is best for this motherboard?
Registered or non-registered, or is that only Socket 940?
DDR or DDR2?
Buffered or unbuffered?
Does it take advantage of each?
I was looking at buying:
https://www.monarchcomputer.com/Merchant2/merchant.mv?Screen=PROD&Store_Code=M&Product_Code=140783
or
http://www.monarchcomputer.com/Merchant2/merchant.mv?Screen=PROD&Store_Code=M&Product_Code=140308&Category_Code=Unbuffered_Corsair
or
http://www.monarchcomputer.com/Merchant2/merchant.mv?Screen=PROD&Store_Code=M&Product_Code=140328&Category_Code=Unbuffered_Corsair
or
http://www.monarchcomputer.com/Merchant2/merchant.mv?Screen=PROD&Store_Code=M&Product_Code=140866&Category_Code=Unbuffered_Corsair
I did read as many memory threads as I could.

You get best timings with theese , and they would be excellent :
http://www.monarchcomputer.com/Merchant2/merchant.mv?Screen=PROD&Store_Code=M&Product_Code=140866&Category_Code=Unbuffered_Corsair
And a total of 1GB would be enough for most of us .
As for your DDR333 ram , it should run dual channel if placed in one green and one purple slot .
Slot 1+2 is recommended if only two modules are used .

MOVED: K8N SLI Platinum - BIOS Update

This topic has been moved to AMD64 nVidia Based board.
K8N SLI Platinum - BIOS Update

Sorry, I'm dozzy... I've since discovered that it's a 219 Mhz problem, there's a sticky in the overclocking section on how to overcome it, and it doesn't apply to me anyway, 'cause I've got a Venice...

Need help troubleshooting issues with Adobe Reader X

Hello,
Recently our company upgraded multilpe computers to Reader X. Initially we installed version 10.1.0. Ever since our users on X have been experiencing problems. We are seeing three different issues.
1) A user will fill out the PDF and click print. At that point a popup appears with the message "Adobe Reader has encountered a problem and needs to close. We are sorry for the inconvenience." The user has the choice to click on Debug or Close. Clicking Debug doesn't appear to do anything.
2) Clicking on a PDF in internet explorer will launch Adobe Reader and a progress bar shows on the screen indicating that the PDF is loading. The progress bar goes away and the user is left looking at a grey screen.
3) When attempting to open a PDF the user recieves this message "The instruction at "0x00720065" referenced memory at "0x00720065" . The memory could not be "written."
In every situation the only way to get past the problems is a restart of the PC.
As an attempt to resolve the issue we tried upgrading several users to Reader version 10.1.3. This was done by completely uninstalling version 10.1.0 and then installing 10.1.3. This did not have any effect on the problems.
Can anyone here offer and suggestions?
Thank you

Hello,
1. The OS on which you are seeing these issues.
Windows XP SP3
2. The method of deployment of the 10.1.3 update. Was it done via SMS/GPO/SCUP?
Originally 10.1.0 was installed remotely using a program PSEXEC. Once the errors began occurring 10.1.0 was uninstalled manually and 10.1.3 was installed using a copy from your ftp site.
3. Can you try and update any one of your systems to the latest version of Reader i.e. Reader 10.1.4 and see if it solves the problem.
We have upgraded one machine to 10.1.4 using the Check for Updates function within Reader 10.1.3 and are looking for any ongoing issues.
4. Which browser are you using to render the PDFs. Is the issue seen with internal links alone or with all links. Can you try and see if the following opens on one of the faulty machine: http://kb2.adobe.com/cps/837/cpsid_83708/attachments/Acrobat_Reader_Re leaseNote_10.1.3.pdf<http://kb2.adobe.com/cps/837/cpsid_83708/attachments/Acrobat_Reader_ReleaseNote_10.1.3.pdf>
We are using IE 8. The issues are seen with both internal and external links as well as stand alone PDFs. No one could open the link you sent but we could open: http://helpx.adobe.com/content/dam/kb/en/837/cpsid_83708/attachments/Acrobat_Reader_Releas eNote_10.1.3.pdf on a faulty machine.
5. If suggestion# 3 doesn't work, can you also try and uninstall the installation on any one of the machines manually (i.e. via Control Panel > Add/Remove Programs or Programs and Features depending upon your OS) and install a fresh copy of Reader 10.1.3 (from ftp://ftp.adobe.com/pub/adobe/reader/win/10.x/10.1.3/en_US/AdbeRdr1013 enUS.exe<ftp://ftp.adobe.com/pub/adobe/reader/win/10.x/10.1.3/en_US/AdbeRdr1013_en_US.exe>) and see if it solves the problem. If it does, then it may be an issue with the Deployment methodology followed.
Already tried this. See answer to suggestion #2
Thanks,
Adam Behsmann
Application Support Analyst
Exchange Bank
(707) 541-1044

Major issues with nforce3 250GB IDE controller: help needed

I am currently facing the following issues with the IDE controller of the Nforce3 250GB:
1.   On random occasions, the PC hangs on the BIOS boot logo (Platinum) and fails to detect the IDE drives.
2.   In most of the above cases, one of the PATA drives (generally the Seagate ST340016A) is not detected.
3.   Sometimes, the PC shows a faded ‘Windows XP’ boot logo and gets stuck there.
4.   Occasionally, the PC boots successfully into Windows but runs slower than a 386 (All IDE read/write operations take an eternity to complete)
I have thoroughly checked all the drives using Seagate SEATOOLS and Samsung HUTIL (done a complete surface scan and IDE cable checks) and found no errors.
All the drives are configured using the ‘Cable select’ option on their respective jumper terminals.
Here is a short summary of the drives:
Samsung SP0802N (boot drive), PATA primary master (Cable select)
Seagate ST340016A PATA primary slave (Cable select)
Seagate SATA drive with 2MB cache (shall update model number soon)
Optical drives:
Asus CD writer Secondary master, cable select
Asus DVD Rom secondary slave cable select
--Total 4 PATA devices, 1 SATA device NO RAID
All the drives have been checked thoroughly. They are working fine. However, the motherboard fails to detect them on random occasions.
I have tried resetting the CMOS.
Configuration:
Athlon 64 3000+ E6 core with SSE3 support
MSI K8N Neo2-FX BIOS 1.C
1GB dual channel kit Corsair TWINX1024-3200C2 running at 2.5-3-3-8 @ 2.75 V
XFX 7600GT AGP (1.5V AGP)
Seagate ST340016A 7200 RPM PATA
Samsung SP0802N 7200 RPM SATA
Seagate 80GB SATA Drive with 2 MB cache
ANTEC Smartpower SL450 450 watt PSU
Windows XP Home Edition SP2 + all updates
Latest drivers for everything

Hi,
I am back here after a long long time Now a days, I run a Intel 965P based Core 2 Duo as my primary desktop. I still use my AMD64 platform and I did fix all the issues with it!
Sorry, I didn't update this thread earlier with the details of how I had solved those issues...
Well, initially I could not get my Radeon 9600XT to work on the nforce 3. I dirched it and got a 7600GT and that solved the GFX crashes..
The HDD problem (the one that I described in this thread) was fixed by:
1. Using the SATA ports 3 & 4 instead of SATA1 & 2!!!
Apparently, the issue of the cyclic reboot & the faded XP logo crash during reboot happens with a lot of Nforce 3 250 owners.
Using the other set of SATA ports fixes this for good...
I also replaced the 40GB Seagate ... But that wasn't the cause of this issue, because the cyclic reboot recurred with the remaining HDDs when SATA1 & 2 were in use...
Motherboards are really quirky, I admit

Please help! Issues with file permissions on the 'Edit' file created by LR for editing in Photoshop?

I am running a Macbook Pro with Mountain Lion. I use a Netgear ReadyNas as my storage device. I can Save, Re Save, Delete and add files without any concern on the ReadyNas from within PS or LR. However when I use the 'Edit in Photoshop" command on LR. I chose the 'Edit a copy with edits', LR creates the new duplicate 'edit' file in the same directory as the original. It opens in PS, I edit as required, however when I save the file to return to LR, I am informed that the file is locked and that I need to edit settings on file or folder, even though the settings are working for all other edits etc. I have had Netgear on this for 3 hours this evening and they cannot see any issues with the setting on the ReadyNas. Does anyone know what permissions are changed or why they are changing when the file is being created by LR?
Sorry bit of a long winded one - but I hope that all makes sense?

h264 is highly compressed and might be the reason your skimming isn't smooth, it may also take a bit more time to convert. I don't have to worry all that much about space so I haven't particularly tried it and can't say whether there are any drawbacks of doing so.
If you google 'mpegstreamclip tutorials', you will see quite a few tutorials you can look at, they do tend to be specific to one task which may not exactly fit in with what you are trying to do, but looking at a few might give you a better understanding of what some options do and when to use them if at all.

WRT54G2 connection issues with a windows 2000 laptop, HELP!!! please?

Ok, at my house I have a newer version of a wireless router (I can't remember which). The old windows 2000 laptop that I have connects perfectly there, but when I installed a WRT54G2 router at my grandma's house it wouldn't connect to the router. My vista laptop and my grandma's vista desktop both are connecting to the router fine (as is evident in my typing this right now), but not the windows 2000.
It is registering that the signal exists, however, it says that it is out of range and it can't connect every time I try. Which makes no sense at all because the laptop in question is sitting no more than 4 ft away from the router.....
It's driving me insane! Does anyone have any suggestions on fixing this problem? Plus I'm not even sure if it's an issue with the computer or if it's an issue with the router itself......
Any ideas would be GREATLY appreciated!
Thanks,
illueia
P.S. sorry if I was too rambley...... or I wasn't clear enough....

Download and install the latest driver for your wireless card...
I aaume the security on the WRT54G2 wireless router must be WPA/WPA2 and that's the reason your Laptop(win2000) does not connect to it...
What error do you get when you attempt to connect to the Wireless Network ?
If it connects to your wireless network then what IP Address do you get for your Wireless Connection ?

[Resolved] No boot with K8N sli Platinum & AMD 64 X2 3800+

Hye,
I've received these new stuff last night (everything is good until here) :
- Antec Sonata II 450W
- MB MSI K8N SLI Platinum
- Proc. AMD 64 X2 3800+
- GC Sapphire X800 XL 256Mo
I've assembled all and turned it on... No bip... but all the fans are turning... and the screen says "No signal" and becomes black ( and me )
Can someone help me? Please?
On the MSI site, I also found this :
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_cpu_support_detail.php?UID=641&kind=1
Maybe the proc. and the Motherboard are not compatible? Has someone already tried this combinaison (MB+Proc.)?
My Thanks in advance.

Quote from: darinn on 12-November-05, 03:22:08
I will ask the sellers if they can update the Mobo for me.
But with the last version of the bios, will the mobo accept the dual-core with this proc. AMD 64 X2 3800+?
And if it's not possible I'll change the mobo.
Thanks .................................. again.
Pretty much any SLI motherboard supports the X2 3800. MSI is just really pathetic sometimes. So, I had the Abit AN8 SLI before and their latest BIOS (17) supports all X2 CPUs. But Im sure most other brands support them too.

Sata issues with k8n-fsr

Hi list!
I have serious issues with my sata drive on my K8N Neo-FSR.
The SATA drive is connected on the SATA3 controller, and an IDE DVD is connected as master on IDE channel 1. The DVD is detected by the BIOS and can be booted...
BUT, the SATA hard drive is not detected by the BIOS, and so neither by WinXP or Linux installers...
I tried loads of configurations settings in the BIOS like SATA3/4 Enabled, RAID IDE enabled, ... Boot priority options do not show the HD...
Please help!!!!!!!
Here is my config:
MSI K8N Neo-FSR (NVIDIA nForce3 250Gb)
Hitachi 160 Go 7200 RPM 8 Mo Serial ATA (bulk)
Sapphire Radeon 9800 Pro
NEC ND-3500 - DVD(+/-)RW

hi zorloc,
looking at size of your new drives are they the new ncq capable seagates, in which case it may be a compatability issue. Maxtor 10 series users have had similar issues.
Try updating bios to the new officiial v1.5 which has Raid v4.6 & may be better for these drives.
You'd also be best upgrading to the latest Nvidia 5.1 drivers .
Other than this Try & see if any of the fixes that worked for the Maxtor users work for you.
see Maxtor 16Mb Cache HDDs & Neo2 Problems there are several more member €ric had some success at end of included thread.
Edit: This may also be of interest Ech a fellow Neo 754 user has had a long stuggle trying to get his maxtor 10 to work Updated Neo BIOS to fix Maxtor 16Mb problem?
luck

ECC6 EHP5 issue with authorisations now need access to S_DEVELOP

Hi
We have ECC6 and have just upgraded to EHP5 and have found that many HR reports/transactions now need access to S_DEVELOP authorisation object. This has caused issues with our user roles. Has anyone else experienced this issue?
Many thanks
Julie

Hi Julie,
Please implement SAP note : 1487329 "Additional Authorization Check in ABAP Workbench" that should solve your issue. There is also note 1617448 "WD ABAP Team Calendar needs S_DEVELOP authorization to load". Hope it helps,
Kind Regards
Christine

HELP: SERIOUS ISSUES WITH BILLING

I have had serious issues with BT since joining their service. Without getting into the issues we had with the BT homehub and other things at the start of the contract with them here is what's been happening.
When we joined BT we explained that we wanted a monthly direct debit. Sounds simple enough but apparently not.
I have phoned over 6 times in the last year to change this. It has still not happened. Several times we were told that on the system it said monthly for it to be then taken out quarterly. In July while we were away this happened again. Only as we assumed that as they had informed us it would definitely be on monthly direct debit that it was the money for the whole of the quarter was not there. So when they took the money for a quarterly bill again. We were charged. It has set back other bills as the money had been eaten up by charges for this. As you can imagine we were quite annoyed. This was not our fault and we felt that BT were not capable of holding our account details without taking money they we repeatedly requested not to. I admit we should have kept a closer eye on our bills account but you don't think that a company will repeatedly do this to you.
After phone calls it emerged that they would not say more than a 'sorry' about this.
The saga then continued. I cancelled the quarterly direct debit at the back and have asked BT to send me monthly paper bills. Then last month our phone and internet was cut off.
We rang up and suggested that due to the mix up could they add the money we owed to our monthly bills and we'd pay this off on top of the monthly bill. Despite that the reason we owe this at all is not through any fault of our own but through theirs. The money would have been available had they taken it as repeatedly requested.
We were on the phone for 1hr and 10 mins ( 21st September) to three different people. No, they said must be paid in 10 day. My partner only managed to get money off this in about an hour - the point being we were happy to pay the whole amount over a year and were not allowed. We asked to speak to a manager after 1hr and 10 and were put back to the start of the queue. 16 minutes later the man we spoke to said a manager named Samantha would call us back. No-one did.
On the 22nd of september a rather annoyed me called back and repeatedly requested a manager - sadi would be put though. After 17 minutes the phone went dead.
Called later on same thing phone went dead after requesting a manager at 10 minutes.
Later on called for 28 minutes and told the call centre the issue £20 deducted from amount but said it had to be paid in ten days and a bill would be sent. Was told that the internet would be reconnected that day.
23rd September was hung up on after thre minutes on requesting why the internet had not been connected.
Phoned later. The man that I spoke to said that no action had been put through to reconnect the internet. He would do it and it would be through by 5pm.
My partner phoned at 8pm when the internet still had not been reconnected. It was done the next day.
Today BT phoned to ask if I had the bill ( Not sent) and tell me that the line will be disconnected by the end of the day. i explained that we were in the middle of complaints procedures with them. She looked on the system and said that there were no notes on the account. I asked for a manager and then asked for this managers superior. She put me through to someone that when questioned was not her superior and half way through my explanation of this....you guessed it..... the line went dead.
I am so annoyed that we've been fine with bill paying and as of their mistake we're now in debt to them and feel like we can't sort it out as there is not anyone who will listen or help. Has anyone had similar probelms or does anyone have a number for their English call centre?
Jess

hi Jess,
I am really sorry that you have had so much trouble trying to get this sorted out. I'll get this straightened out.
Could you drop me in an email please to the address in my profile with your BT account and telephone number along with a link back to this thread.
Cheers
Craig
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)”
td-p/30">Ratings star on the left-hand side of the post.
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Freezing issues with K8N Neo2 Plat & 6800 gt

Well I get random freezing during games. Sometimes it freezes for 5-10 seconds then comes back, while other times it just freezes and the sound comes back but not the game.
I had this problem when I first upgraded.
K8N Neo2 plat
1gb corsair xms 3200
athlon 64 3500
aslo have:
420-30? antec tru power supply. I cant remember exact number.
6800gt ultra
audigy 2 plat
Now I first posted my problem a while ago and someone told me to try chaning the HT to 4x instead of 5x. So I did and it worked. It worked for a few weeks and now the problems have come back.
Any Ideas?

Along with the above issues, I've also found that a lot of my gaming probs with the 6800 are due to it being a "bandwidth hog" & it's latency needs to be adjusted lower to enable the other devices on the PCI bus (i.e. sound card) to get enough bandwidth to function properly. This isn't noticeable until you start some heavy gaming with a lot going on at once...
If your game ever practically chugs to a halt when a lot of sounds are being produced, this is the main problem. Here's a way & some notes on how to deal with it. Just like every "tweak" though, it's not guaranteed to work for everyone but I got noticeable benefits from it.
- D/L (I got it @ guru3D) PCI Latency Tool & give the "Read Me" a quick once-over. Write down the values for your devices, in case you need/want to change 'em back. Most items are well labeled - the 6800 & your sound card will be what you are most interested in. I wouldn't mess with the rest of 'em, as they deal with low level system items that are best left alone. Unless you are truly an Uber Geek!
- The latency for my 6800 listed as a massive 248 clks! For some reason, I've read that ATI cards don't default at such a large value, which might explain why people don't seem to have as many performance issues with 'em. Anyhow lower the 6800 to a more "reasonable" value, like 128 or 64. 64 seemed to work best for me.
- Save the settings, reboot & test it out. You can experiement with the sound card latency too, in order to find what works best for you, but I wouldn't set it at less than it's default value (32).
Hope this helps.

Z77A-GD65 with 3570k noobie needs some help.

Hi Guys,
First of all I’m very impressed by the looks of GD65, I just hope it will work as well as it looks…
So finally I should get my RAM tonight (4 x 4gb Sammy ECO ram). I believe there might some issues with o/c the memory, which I believe was a ittle improved in beta bios.
3570k
Silver Arrow SB-E HSF
4 x 4gb Sammy eco ram
Gigabyte gtx670 GPU should arrive early next week.
Corsair TX750
Windows 7 x64 SP1 Home
HAF 922 case
I’ll use this method to upgrade mobo to the latest official BIOS 10.5 using recommeded method.
https://forum-en.msi.com/index.php?topic=108079.0
Also should I wait for Gtx670 to come in next week, or would I be able to use hdmi/dvi output from GD65 (IB HD4000 IGPU) to display 1080P on LG 32LD450 display. I believe there were some reports only VGA output works? Is it true?
Also where should I get most stable NIC Intel drivers (I saw some people having problems with them) and 898 audio drivers?
Is official 10.5 BIOS recommend or is there a “better” beta BIOS I should install (and where do I get it from)?
I do apologize for so many questions, but I’m very scared to put this rig together with so many z77 chipset issues around… I’m just trying to avoid “ I told you so” from my wife… LOL I’m concern about error 55 (memory not installed), in some cases CPU installation issues. I’m coming from several years of AMD builds… so IB it is very new to me…
Any help would be much appreciated…
TIA

I promise as soon as I get everything stable I will test it with 200mm fan as intake and outtake...
I love big sinks and fans, I will post some pictures after everything is done. My system is nothing to brag about, HAF 922 with 3 x 200mm 1 x 120mm, 1 x 140mm and Silver Arrow SB-E (dual tower) HSF. I’m using Lampron fan controller to control fans.
Positive pressure is very interesting concept and some swear it works...
http://www.silverstonetek.com/techtalk_cont.php?tid=wh_positive&area=usa
So I went to bed at 3am last night, I did go far, as I was taking updates, installing drivers, changing drive letters… etc..
System seems to be stable at stock/default 10.3 bios settings, all I changed was to set fans on CPU (I selected 70C to be my goal) and SYSFAN1 to run at 50% (my 140mm internal fan, which is strapped to the drive cage).
The NIC card seems to be working fine, Intel IGPU video works fine (using dvi to hdmi cable). I haven’t installed any temp monitoring software so I cannot tell you how is my IB CPU.
The only problem I found last night was I couldn’t get any audio from rear speaker output (I tried display’s and 2.1 speakers). The driver seems to be working, because I can see sound bar moving up and down. Also when I connect my headphone to my front audio output, I can hear sound and I get pop up saying I have headphones connected. When I remove headphones I get another pop up saying the headphones have been disconnected. When I connect anything to the green output (speaker out), I get pop up saying rear speakers were detected, however there is nothing no static, noise or anything… I tried to disable/enable device without luck. I’ve used all drivers from MSI website, should I try to see if there are newer/older drivers? Since I’m currently using 10.3 BIOS, should I try latest 10.5? Have you guys heard about this problem before? If you have any ideas please let me… I did poke around BIOS but I couldn’t find anything related to audio…
Overall (other than small audio hiccup) “so far” I’m very happy from my purchase…
Thank you

PLEASE HELP! Restarting issue with K8N SLI. need bios help???

Similar Messages

Maybe you are looking for