PNRP though the ASA 5505

Can anyone tell me how to enable Microsoft Easy Connect to be used from within my LAN to laptops in the WAN? I cannot find any enformation related to PNRP and my ASA 5505.

Hello Lex,
i am looking for exactly the same. :-)
What i found about that is an entry in the MSDN board on how to block it. Maybe we can use it the other way. ;-)
http://social.msdn.microsoft.com/Forums/hu-HU/peertopeer/thread/8339b59c-b300-4d69-96b1-6882031d2b6b
i didnt get it to work at the moment. but maybe someone has an idea?
Max

Similar Messages

How do I block pings from the outside to the ASA 5505 outside interface?

I was asked to block pings from the internet to the outside interface of our ASA-5505 firewall. I found a post that said to enter "icmp deny any outside", however that does not do it.
I created an ACL to try and do the trick, also to no avail:
access-list outside_in extended permit icmp any any echo-reply
access-list outside_in in interface outside
access-group outside_in in interface outside
Anyone have a clue what I'm doing wrong? I'm not the firewall guy as you can tell. :/
Thanks in advance...
Block / Deny ICMP Echo (Ping) on Cisco ASA Outside Interface
Most networks that you protect with a Cisco ASA device, will probably want to deny ICMP (maybe not all ICMP types, but a lot of network admins will want to block ICMP Echo, etc.) on the outside interface. This will make the network harder to find through external enumeration, but not impossible.
ASA5505(config)#icmp deny any outside
You will deny ICMP on the outside interface, but if you include ICMP as a protocol in the default global policy map, you can ping from the inside to any host on the outside, and it will be permitted back through the ASA, as it knows about the previous ICMP “connection

You are allowing echo-reply, thus it will reply to a ping
try this ACL:
icmp deny any echo-reply outside
From:
https://supportforums.cisco.com/thread/223769
Eric

Standby VPN in the ASA 5505

Hello, I'm triying find out if there is a way to put a second vpn site-to-site as standby and if the primary come down this standby come to up.
for exemplo, I have a ASA 5505 in my branch office I wish add two VPN site-to-site to my head office. one tunnel must be standby and other active.
there is any way to reach this? the contingency can be by hand it's not necessary be automatic.
any tip is welcome.
thanks

as i unerstand you have two interfacces at the spoke side , then you can do the following :
apply the same crypto map on both interfaces .
routing will control to which path the traffic will have and hence which tunnel will be used to encrypt traffic , to ahcieve redundancy with routing you can use SLA and floating routes , this work as you define a route to the primary tunnel with higher metric but this route is associated with a SLA object the tracks the reachability of the primary ISP, when the tracking fails the route will be removed from the routing table and you will be using a secondary route with a higher metric that will send the traffic to the second tunnel and will be only installed when the primary route is down .
here is a useful example on how to configure SLA on ASA :
ASA/PIX 7.x: Redundant or Backup ISP Links Configuration Example
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a00806e880b.shtml
hope that this will help !
cheers

What is the Sucessor for the ASA 5505 Appliance

Hello,
we are looking for a small Firewall Appliance for branch offices which are connected via MPLS and Internet VPNs in the best case.
We need a small low-priced appliance with the specs of a 5505.
Sometimes the appliances are not Rackmounted but placed inside of small offices, so they need to be silent.
We only need basic Firewalling and IPSec VPN capabilities. No Cloud / Application / Fill-In-Buzzword-here Stuff.
An Hardware Updated 5505 would be ideal.
Is there any real sucessor for the 5505? What would you use for this (other vendors may also apply).
Regards
Sebastian

Up to now, there is no successor for the 5505. Many people expect that something will come soon, I do that for much over a year now ... ;-)
For your needs, a Cisco 880 could be a good buy. Not as fast as the 5505 but much more features for your VPN-deployment.

Cisco ASA 5505 performance issues on downloads - data into the ASA from the Internet

I have having serious issues with performance on my ASA 5505s that I am testing with 9.2.3 code.
I stripped the config and removed as much stuff as I could - no VPN etc. and I am ONLY getting about 30-40Mbps downloads from sites but 95Mbps uploads???? Anyone else seeing these problems? If I remove the firewall my PC can hit 300/300Mbps to the same sites using the same switch and cable.
I installed 1Gb of mem on the ASA 5505 but it made no difference. The ASA has a UL IP Security license but I am only using and inside and outside address for these tests, no other ports configured.
Is anyone else seeing this performance problem with the 9.2.3 code? I went to this from 8.2.5 to try to resolve QOS failure bugs that I found in the 8.2.5 code. I did not expect to have a performance hit though and it is only on downloads TO the ASA from the Internet from all speed test sites that I try. Uploading speeds seem fine. No access-lists on my interfaces either...barebones config.
My FIOS and switch interfaces are fine...no errors on any interfaces and the same switch interface hits 300/300Mbps when my laptop is directly attached.
Anyone have a barebones config on their ASA 5505 that flies...I will try it on mine and see if some command somewhere (hidden) is causing the issue. I even cleared the config and started with a clean slate just in case I was missing some command from the older configs that may have impacted performance.

After changing the switch with a high end switch my performance increased but I am still not happy with the throughput out of my ASA. I have about 50+ ASAs 5505s and a dozen 5510s. Most remote sites have 5505s. All my sites right now have 8.2.5-51 and I wanted to put 9.2.3 out there to solve issues I have uncovered on the 8.2.5 code with regards to QOS issues.
I get much better results using the Cisco 3750X attached to the FIOS (right around 300/300 with my laptop directly attached to the 3750x bypassing the ASA - my FIOS circuit rating is also 300/300). Going through the ASA to the same test site I get download speeds of 35 to 75. Changes randomly which really bothers me. My uploads speeds are ALWAYS faster then my download speeds. Example - best download I would ever get is 75Mb and my upload would usually hit 95Mb during the same test period.
I may have to live with it but the inconsistency is what really bothers me.
Here is the config I am currently using. Nothing going on during testing since only a single PC is attached. VPN tunnel to the main site can be up or down...doesn't seem to make any difference. PC does to site directly from outside interface of ASA...split tunneling. Even when I removed tunnels and tested with just the ASA as a firewall to the Internet I was still seeing the same inconsistencies.
Anything obviously missing - new command or anything? Xlates causing issues?

Internet Connection Became Slow after Introduction of Cisco ASA 5505 to the Network

I configured a Cisco ASA 5505 (Version Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
in transparent firewall mode and inserted after Cisco 1700 router. However, the internet connection became very slow and users are compaining that they cannot load any pages.
My setup looks like:
Internet --> Cisco 1700 --> Cisco ASA 5505 --> LAN
The license information is:
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs                       : 3, DMZ Restricted
Inside Hosts                : Unlimited
Failover                    : Disabled
VPN-DES                     : Enabled
VPN-3DES-AES                : Enabled
VPN Peers                   : 10
WebVPN Peers                : 2
Dual ISPs                   : Disabled
VLAN Trunk Ports            : 0
This platform has a Base license.
The flash activation key is the SAME as the running key.
My running-config looks like:
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
domain-name default.domain.invalid
enable password 8Ry2YjIyt7RRXU24 encrypted
names
interface Vlan1
nameif inside
security-level 100
no shut
interface Vlan2
nameif outside
security-level 0
no shut
interface Ethernet0/0
switchport access vlan 2
no shut
interface Ethernet0/1
no shut
interface Ethernet0/2
no shut
interface Ethernet0/3
no shut
interface Ethernet0/4
no shut
interface Ethernet0/5
no shut
interface Ethernet0/6
no shut
interface Ethernet0/7
no shut
passwd 2KFQnbNIdI.2KYOU encrypted
regex urllist1 ".*\.([Ee][Xx][Ee]|[Cc][Oo][Mm]|[Bb][Aa][Tt]) HTTP/1.[01]"
regex urllist2 ".*\.([Pp][Ii][Ff]|[Vv][Bb][Ss]|[Ww][Ss][Hh]) HTTP/1.[01]"
regex urllist3 ".*\.([Dd][Oo][Cc]|[Xx][Ll][Ss]|[Pp][Pp][Tt]) HTTP/1.[01]"
regex urllist4 ".*\.([Zz][Ii][Pp]|[Tt][Aa][Rr]|[Tt][Gg][Zz]) HTTP/1.[01]"
regex domainlist1 "\.facebook\.com"
regex domainlist2 "\.diretube\.com"
regex domainlist3 "\.youtube\.com"
regex domainlist4 "\.vimeo\.com"
regex applicationheader "application/.*"
regex contenttype "Content-Type"
ftp mode passive
dns server-group DefaultDNS
domain-name default.domain.invalid
access-list outside_in extended permit ip any any
access-list inside_mpc extended permit tcp any any eq www
access-list inside_mpc extended permit tcp any any eq 8080
pager lines 24
mtu outside 1500
mtu inside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
access-group outside_in in interface outside
route outside 0.0.0.0 0.0.0.0 192.168.1.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domainlist1
match regex domainlist2
match regex domainlist3
match regex domainlist4
class-map type inspect http match-all BlockDomainsClass
match request header host regex class DomainBlockList
class-map type regex match-any URLBlockList
match regex urllist1
match regex urllist2
match regex urllist3
match regex urllist4
class-map inspection_default
match default-inspection-traffic
class-map type inspect http match-all AppHeaderClass
match response header regex contenttype regex applicationheader
class-map httptraffic
match access-list inside_mpc
class-map type inspect http match-all BlockURLsClass
match request uri regex class URLBlockList
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map type inspect http http_inspection_policy
parameters
protocol-violation action drop-connection
class AppHeaderClass
drop-connection log
match request method connect
drop-connection log
class BlockDomainsClass
reset log
class BlockURLsClass
reset log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect netbios
inspect rsh
inspect rtsp
inspect skinny
inspect esmtp
inspect sqlnet
inspect sunrpc
inspect tftp
inspect sip
inspect xdmcp
policy-map inside-policy
class httptraffic
inspect http http_inspection_policy
service-policy global_policy global
service-policy inside-policy interface inside
prompt hostname context
Cryptochecksum:8ab1a53df6ae3c202aee236d6080edfd
: end
Could the slow internet connection be due to license limitations? Or is there something wrong with my configuration?
Please see the configuration and help.
Thanks

I have re-configured the ASA 5505 yesterday and so far it's working fine. I am not sure if the problem will re-appear later on. Anyways here is my sh tech-support
ciscoasa# sh tech-support
Cisco Adaptive Security Appliance Software Version 7.2(3)
Device Manager Version 5.2(3)
Compiled on Wed 15-Aug-07 16:08 by builders
System image file is "disk0:/asa723-k8.bin"
Config file at boot was "startup-config"
ciscoasa up 14 hours 16 mins
Hardware:   ASA5505, 256 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash M50FW080 @ 0xffe00000, 1024KB
Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
                             Boot microcode   : CNlite-MC-Boot-Cisco-1.2
                             SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
                             IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Int: Internal-Data0/0    : address is 001f.9ee8.ffa2, irq 11
1: Ext: Ethernet0/0         : address is 001f.9ee8.ff9a, irq 255
2: Ext: Ethernet0/1         : address is 001f.9ee8.ff9b, irq 255
3: Ext: Ethernet0/2         : address is 001f.9ee8.ff9c, irq 255
4: Ext: Ethernet0/3         : address is 001f.9ee8.ff9d, irq 255
5: Ext: Ethernet0/4         : address is 001f.9ee8.ff9e, irq 255
6: Ext: Ethernet0/5         : address is 001f.9ee8.ff9f, irq 255
<--- More --->
7: Ext: Ethernet0/6         : address is 001f.9ee8.ffa0, irq 255
8: Ext: Ethernet0/7         : address is 001f.9ee8.ffa1, irq 255
9: Int: Internal-Data0/1    : address is 0000.0003.0002, irq 255
10: Int: Not used            : irq 255
11: Int: Not used            : irq 255
Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs                       : 3, DMZ Restricted
Inside Hosts                : Unlimited
Failover                    : Disabled
VPN-DES                     : Enabled
VPN-3DES-AES                : Enabled
VPN Peers                   : 10
WebVPN Peers                : 2
Dual ISPs                   : Disabled
VLAN Trunk Ports            : 0
This platform has a Base license.
Serial Number: JMX1211Z2N4
Running Activation Key: 0xaf0ed046 0xbcf18ebf 0x80b38508 0xba785cc0 0x05250493
Configuration register is 0x1
Configuration has not been modified since last system restart.
<--- More --->
------------------ show clock ------------------
18:32:58.254 UTC Tue Nov 26 2013
------------------ show memory ------------------
Free memory:       199837144 bytes (74%)
Used memory:        68598312 bytes (26%)
Total memory:      268435456 bytes (100%)
------------------ show conn count ------------------
1041 in use, 2469 most used
------------------ show xlate count ------------------
0 in use, 0 most used
------------------ show blocks ------------------
SIZE    MAX    LOW    CNT
     0    100     68    100
<--- More --->
     4    300    299    299
    80    100     92    100
   256    100     94    100
1550   6174   6166   6174
2048   1124    551    612
------------------ show blocks queue history detail ------------------
History buffer memory usage: 2136 bytes (default)
------------------ show interface ------------------
Interface Internal-Data0/0 "", is up, line protocol is up
Hardware is y88acs06, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 001f.9ee8.ffa2, MTU not set
IP address unassigned
18491855 packets input, 11769262614 bytes, 0 no buffer
Received 213772 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops, 0 demux drops
18185861 packets output, 11626494317 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 late collisions, 0 deferred
<--- More --->
0 input reset drops, 0 output reset drops
input queue (curr/max packets): hardware (0/0) software (0/0)
output queue (curr/max packets): hardware (0/55) software (0/0)
Control Point Interface States:
Interface number is unassigned
Interface Internal-Data0/1 "", is administratively down, line protocol is up
Hardware is 88E6095, BW 1000 Mbps
(Full-duplex), (1000 Mbps)
MAC address 0000.0003.0002, MTU not set
IP address unassigned
18184216 packets input, 11625360131 bytes, 0 no buffer
Received 206655 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 switch ingress policy drops
18490057 packets output, 11768078777 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Loopback0 "_internal_loopback", is up, line protocol is up
Hardware is VirtualMAC address 0000.0000.0000, MTU 1500
IP address 127.1.0.1, subnet mask 255.255.0.0
<--- More --->
Traffic Statistics for "_internal_loopback":
1 packets input, 28 bytes
1 packets output, 28 bytes
1 packets dropped
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Control Point Interface States:
Interface number is 28
Interface config status is active
Interface state is active
Interface Vlan1 "inside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa2, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "inside":
7742275 packets input, 903584114 bytes
10645034 packets output, 10347291114 bytes
184883 packets dropped
      1 minute input rate 320 pkts/sec, 35404 bytes/sec
      1 minute output rate 325 pkts/sec, 313317 bytes/sec
<--- More --->
      1 minute drop rate, 17 pkts/sec
      5 minute input rate 399 pkts/sec, 59676 bytes/sec
      5 minute output rate 483 pkts/sec, 503200 bytes/sec
      5 minute drop rate, 9 pkts/sec
Control Point Interface States:
Interface number is 1
Interface config status is active
Interface state is active
Interface Vlan2 "outside", is up, line protocol is up
Hardware is EtherSVI
MAC address 001f.9ee8.ffa3, MTU 1500
IP address 192.168.1.254, subnet mask 255.255.255.0
Traffic Statistics for "outside":
10750090 packets input, 10432619059 bytes
7541331 packets output, 870613684 bytes
109911 packets dropped
      1 minute input rate 328 pkts/sec, 313770 bytes/sec
      1 minute output rate 301 pkts/sec, 32459 bytes/sec
      1 minute drop rate, 2 pkts/sec
      5 minute input rate 485 pkts/sec, 503789 bytes/sec
      5 minute output rate 387 pkts/sec, 57681 bytes/sec
      5 minute drop rate, 2 pkts/sec
Control Point Interface States:
Interface number is 2
<--- More --->
Interface config status is active
Interface state is active
Interface Ethernet0/0 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
Available but not configured via nameif
MAC address 001f.9ee8.ff9a, MTU not set
IP address unassigned
10749794 packets input, 10630700889 bytes, 0 no buffer
Received 2506 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
3 switch ingress policy drops
7541070 packets output, 1028190148 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/1 "", is up, line protocol is up
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
<--- More --->
Available but not configured via nameif
MAC address 001f.9ee8.ff9b, MTU not set
IP address unassigned
7741977 packets input, 1064586806 bytes, 0 no buffer
Received 211282 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
10644663 packets output, 10543362751 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/2 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9c, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
<--- More --->
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/3 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9d, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
<--- More --->
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/4 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9e, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
<--- More --->
Interface number is unassigned
Interface Ethernet0/5 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ff9f, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/6 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
<--- More --->
MAC address 001f.9ee8.ffa0, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
Interface Ethernet0/7 "", is down, line protocol is down
Hardware is 88E6095, BW 100 Mbps
Auto-Duplex, Auto-Speed
Available but not configured via nameif
MAC address 001f.9ee8.ffa1, MTU not set
IP address unassigned
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
<--- More --->
0 L2 decode drops
0 switch ingress policy drops
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
0 rate limit drops
0 switch egress policy drops
Control Point Interface States:
Interface number is unassigned
------------------ show cpu usage ------------------
CPU utilization for 5 seconds = 12%; 1 minute: 11%; 5 minutes: 11%
------------------ show cpu hogging process ------------------
Process:      Dispatch Unit, NUMHOG: 1, MAXHOG: 133, LASTHOG: 140
LASTHOG At:   04:45:59 UTC Nov 26 2013
PC:           8be0f7
Traceback:    8bed19 8bf553 302b87 3030a5 2fad69 7674bf 75ca16
              c6251d c62a4c c62f6c 75c653 767820 797f64 769c85
<--- More --->
------------------ show process ------------------
    PC       SP       STATE       Runtime    SBASE     Stack Process
Mwe 00c9bb24 01bb8700 013e3250          0 01733fc8 15616/16384 emweb/cifs
Lwe 001072ac 0176f9c4 013e32d0          0 0176d9f0 8132/8192 block_diag
Mrd 00223a67 01783d5c 013e33b0     314854 0177be18 25752/32768 Dispatch Unit
Msi 00f82847 01b07b84 013e3250        229 01b05bc0 7984/8192 y88acs06 OneSec Thread
Mwe 0011b1a5 01b09cfc 013e3250          0 01b07d88 7864/8192 Reload Control Thread
Mwe 00120606 01b1260c 013e5258          0 01b10988 7256/8192 aaa
Mwe 001486aa 01b19404 013e5ae8          0 01b15450 16020/16384 CMGR Server Process
Mwe 0014c3c5 01b1b4d4 013e3250          0 01b19570 7968/8192 CMGR Timer Process
Lwe 002227a1 01b239b4 013ee360          0 01b219f0 7524/8192 dbgtrace
Mwe 004e1ba5 01b29c34 013e3250        157 01b27d50 6436/8192 eswilp_svi_init
Mwe 01064b1d 01b4a7f4 013e3250          0 01b48890 7848/8192 Chunk Manager
Msi 008b61b6 01b52d54 013e3250        230 01b50da0 7856/8192 PIX Garbage Collector
Lsi 00ecb6ac 01b54e94 013e3250         12 01b52ec0 7552/8192 route_process
Mwe 008a5ddc 01b5dc04 0133b430          0 01b5bc40 8116/8192 IP Address Assign
Mwe 00acb779 01b60604 01346e10          0 01b5e640 8116/8192 QoS Support Module
Mwe 0091eba9 01b6275c 0133c530          0 01b60798 8116/8192 Client Update Task
Lwe 01083c8e 01b656d4 013e3250     123088 01b63770 7840/8192 Checkheaps
Mwe 00acfd7d 01b6b824 013e3250        623 01b69ad0 3476/8192 Quack process
Mwe 00b2a260 01b6dad4 013e3250         22 01b6bbf0 7364/8192 Session Manager
Mwe 00c55efd 01b78564 031d0478          4 01b74a50 14768/16384 uauth
<--- More --->
Mwe 00be3c9e 01b7aaec 0135c010          0 01b78b28 7524/8192 Uauth_Proxy
Mwe 00c52759 01b80e0c 01361770          0 01b7ee88 7712/8192 SMTP
Mwe 00c3f7b9 01b82eec 01361710          0 01b80fa8 7412/8192 Logger
Mwe 00c3fd26 01b8502c 013e3250          0 01b830c8 7492/8192 Thread Logger
Mwe 00f62272 01b9596c 013ac520          0 01b939c8 7188/8192 vpnlb_thread
Msi 00b4097c 01c598c4 013e3250        190 01c578f0 8000/8192 emweb/cifs_timer
Msi 005bd338 017a909c 013e3250      25855 017a7108 7412/8192 arp_timer
Mwe 005c76bc 01b486e4 013fba50      20643 01b46770 7348/8192 arp_forward_thread
Mwe 00c5a919 023fa5fc 013619e0          0 023f8648 7968/8192 tcp_fast
Mwe 00c5a6e5 023fc624 013619e0          0 023fa670 7968/8192 tcp_slow
Mwe 00c754d1 0240d42c 013628a0          0 0240b478 8100/8192 udp_timer
Mwe 0019cb17 01b404a4 013e3250          0 01b3e530 7984/8192 CTCP Timer process
Mwe 00efe8b3 0308c15c 013e3250          0 0308a208 7952/8192 L2TP data daemon
Mwe 00efef23 0308e194 013e3250          0 0308c230 7968/8192 L2TP mgmt daemon
Mwe 00eea02b 030c62ac 013a5c10         43 030c2338 16244/16384 ppp_timer_thread
Msi 00f62d57 030c82f4 013e3250        264 030c6360 7924/8192 vpnlb_timer_thread
Mwe 001b96e6 01b7cbbc 01b1e9c8          1 01b7ac48 7728/8192 IPsec message handler
Msi 001c9bac 01b8d4dc 013e3250       2917 01b8b548 7648/8192 CTM message handler
Mwe 00af93b8 031465b4 013e3250          0 03144640 7984/8192 ICMP event handler
Mwe 00831003 0314a724 013e3250        387 031467b0 16100/16384 IP Background
Mwe 0021b267 031a83c4 013123c0         31 03188450 123488/131072 tmatch compile thread
Mwe 009f2405 03290044 013e3250          0 0328c0c0 16072/16384 Crypto PKI RECV
Mwe 009f305a 03294144 013e3250          0 032901e0 16040/16384 Crypto CA
Mwe 0064d4fd 01b3e24c 013e3250          8 01b3c2f8 7508/8192 ESW_MRVL switch interrupt service
<--- More --->
Msi 00646f5c 032c134c 013e3250    3059378 032bf448 7184/8192 esw_stats
Lsi 008cbb80 032dc704 013e3250          3 032da730 7908/8192 uauth_urlb clean
Lwe 008afee7 034a0914 013e3250        197 0349e9b0 6636/8192 pm_timer_thread
Mwe 0052f0bf 034a35ac 013e3250          0 034a1648 7968/8192 IKE Timekeeper
Mwe 00520f6b 034a8adc 0132e2b0          0 034a4e38 15448/16384 IKE Daemon
Mwe 00bf5c78 034ac7ac 01360680          0 034aa7f8 8100/8192 RADIUS Proxy Event Daemon
Mwe 00bc32de 034ae79c 034dcbe0          0 034ac918 7208/8192 RADIUS Proxy Listener
Mwe 00bf5e0f 034b099c 013e3250          0 034aea38 7968/8192 RADIUS Proxy Time Keeper
Mwe 005aac4c 034b3154 013fb980          0 034b1250 7492/8192 Integrity FW Task
M* 008550a5 0009fefc 013e33b0       3183 034e3b20 24896/32768 ci/console
Msi 008eb694 034ed9d4 013e3250       2370 034ebc40 6176/8192 update_cpu_usage
Msi 008e6415 034f7dac 013e3250       1096 034f5eb8 6124/8192 NIC status poll
Mwe 005b63e6 03517d1c 013fbd10       1963 03515d78 7636/8192 IP Thread
Mwe 005becbe 03519e4c 013fbcb0          3 03517e98 7384/8192 ARP Thread
Mwe 004c2b36 0351befc 013fbae0          0 03519fe8 7864/8192 icmp_thread
Mwe 00c7722e 0351e06c 013e3250          0 0351c108 7848/8192 udp_thread
Mwe 00c5d126 0352008c 013fbd00          0 0351e228 7688/8192 tcp_thread
Mwe 00bc32de 03a6982c 03a5ee18          0 03a679b8 7512/8192 EAPoUDP-sock
Mwe 00266c15 03a6b614 013e3250          0 03a699e0 7032/8192 EAPoUDP
Mwe 005a6728 01b27b94 013e3250          0 01b25c30 7968/8192 Integrity Fw Timer Thread
-     -        -         -      47686621    -         -     scheduler
-     -        -         -      51253819    -         -     total elapsed
------------------ show failover ------------------
<--- More --->
ERROR: Command requires failover license
------------------ show traffic ------------------
inside:
received (in 51429.740 secs):
7749585 packets905087345 bytes
67 pkts/sec17013 bytes/sec
transmitted (in 51429.740 secs):
10653162 packets10355908020 bytes
40 pkts/sec201026 bytes/sec
      1 minute input rate 412 pkts/sec, 51803 bytes/sec
      1 minute output rate 475 pkts/sec, 522952 bytes/sec
      1 minute drop rate, 24 pkts/sec
      5 minute input rate 399 pkts/sec, 59676 bytes/sec
      5 minute output rate 483 pkts/sec, 503200 bytes/sec
      5 minute drop rate, 9 pkts/sec
outside:
received (in 51430.240 secs):
10758403 packets10441440193 bytes
42 pkts/sec203021 bytes/sec
transmitted (in 51430.240 secs):
7548339 packets872053854 bytes
<--- More --->
63 pkts/sec16037 bytes/sec
      1 minute input rate 479 pkts/sec, 523680 bytes/sec
      1 minute output rate 387 pkts/sec, 46796 bytes/sec
      1 minute drop rate, 3 pkts/sec
      5 minute input rate 485 pkts/sec, 503789 bytes/sec
      5 minute output rate 387 pkts/sec, 57681 bytes/sec
      5 minute drop rate, 2 pkts/sec
_internal_loopback:
received (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51430.740 secs):
1 packets28 bytes
0 pkts/sec0 bytes/sec
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Aggregated Traffic on Physical Interface
<--- More --->
Ethernet0/0:
received (in 51431.740 secs):
10758462 packets10640075825 bytes
42 pkts/sec206042 bytes/sec
transmitted (in 51431.740 secs):
7548383 packets1029818127 bytes
63 pkts/sec20023 bytes/sec
      1 minute input rate 485 pkts/sec, 537048 bytes/sec
      1 minute output rate 395 pkts/sec, 54546 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 485 pkts/sec, 511723 bytes/sec
      5 minute output rate 387 pkts/sec, 65495 bytes/sec
      5 minute drop rate, 0 pkts/sec
Ethernet0/1:
received (in 51433.570 secs):
7749780 packets1066328930 bytes
67 pkts/sec20064 bytes/sec
transmitted (in 51433.570 secs):
10653359 packets10552787020 bytes
40 pkts/sec205006 bytes/sec
      1 minute input rate 419 pkts/sec, 59621 bytes/sec
      1 minute output rate 480 pkts/sec, 533950 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 399 pkts/sec, 67618 bytes/sec
<--- More --->
      5 minute output rate 482 pkts/sec, 511073 bytes/sec
      5 minute drop rate, 0 pkts/sec
Ethernet0/2:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Ethernet0/3:
received (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.730 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
<--- More --->
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Ethernet0/4:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Ethernet0/5:
received (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51434.870 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
<--- More --->
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Ethernet0/6:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Ethernet0/7:
received (in 51435.010 secs):
0 packets0 bytes
0 pkts/sec0 bytes/sec
transmitted (in 51435.010 secs):
<--- More --->
0 packets0 bytes
0 pkts/sec0 bytes/sec
      1 minute input rate 0 pkts/sec, 0 bytes/sec
      1 minute output rate 0 pkts/sec, 0 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 0 pkts/sec, 0 bytes/sec
      5 minute output rate 0 pkts/sec, 0 bytes/sec
      5 minute drop rate, 0 pkts/sec
Internal-Data0/0:
received (in 51435.510 secs):
18513901 packets11784250044 bytes
25 pkts/sec229023 bytes/sec
transmitted (in 51435.510 secs):
18207269 packets11641332179 bytes
19 pkts/sec226078 bytes/sec
      1 minute input rate 891 pkts/sec, 595715 bytes/sec
      1 minute output rate 863 pkts/sec, 588935 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 885 pkts/sec, 584035 bytes/sec
      5 minute output rate 870 pkts/sec, 580393 bytes/sec
      5 minute drop rate, 0 pkts/sec
Internal-Data0/1:
received (in 51436.010 secs):
18207323 packets11641364184 bytes
<--- More --->
19 pkts/sec226076 bytes/sec
transmitted (in 51436.010 secs):
18513954 packets11784281987 bytes
25 pkts/sec229022 bytes/sec
      1 minute input rate 855 pkts/sec, 575808 bytes/sec
      1 minute output rate 884 pkts/sec, 582339 bytes/sec
      1 minute drop rate, 0 pkts/sec
      5 minute input rate 869 pkts/sec, 578350 bytes/sec
      5 minute output rate 883 pkts/sec, 581924 bytes/sec
      5 minute drop rate, 0 pkts/sec
------------------ show perfmon ------------------
PERFMON STATS:    Current      Average
Xlates               0/s          0/s
Connections         17/s          6/s
TCP Conns            8/s          2/s
UDP Conns            7/s          2/s
URL Access           0/s          0/s
URL Server Req       0/s          0/s
TCP Fixup            0/s          0/s
TCP Intercept        0/s          0/s
HTTP Fixup           0/s          0/s
<--- More --->
FTP Fixup            0/s          0/s
AAA Authen           0/s          0/s
AAA Author           0/s          0/s
AAA Account          0/s          0/s
------------------ show counters ------------------
Protocol     Counter                     Value   Context
IP           IN_PKTS                  168960   Summary
IP           OUT_PKTS                 169304   Summary
IP           TO_ARP                       61   Summary
------------------ show history ------------------
------------------ show firewall ------------------
Firewall mode: Transparent
------------------ show running-config ------------------
<--- More --->
: Saved
ASA Version 7.2(3)
firewall transparent
hostname ciscoasa
enable password
names
interface Vlan1
nameif inside
security-level 100
interface Vlan2
nameif outside
security-level 0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
<--- More --->
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd
regex domain1 ".facebook\.com"
regex domain2 ".fb\.com"
regex domain3 ".youtube\.com"
ftp mode passive
access-list ACL_IN extended permit ip any any
pager lines 24
mtu inside 1500
mtu outside 1500
ip address 192.168.1.254 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-523.bin
no asdm history enable
<--- More --->
arp timeout 14400
access-group ACL_IN in interface outside
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
telnet timeout 5
ssh timeout 5
console timeout 0
class-map type regex match-any DomainBlockList
match regex domain1
match regex domain2
match regex domain3
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
<--- More --->
message-length maximum 512
match domain-name regex class DomainBlockList
drop-connection log
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:bb5115ea1d14ee42e7961ef0c9aaed86
: end
<--- More --->
------------------ show startup-config errors ------------------
INFO: No configuration errors
------------------ console logs ------------------
Message #1 : Message #2 : Message #3 : Message #4 : Message #5 : Message #6 : Message #7 : Message #8 : Message #9 : Message #10 : Message #11 : Message #12 : Message #13 : Message #14 :
Total SSMs found: 0
Message #15 :
Total NICs found: 10
Message #16 : 88E6095 rev 2 Gigabit Ethernet @ index 09Message #17 : MAC: 0000.0003.0002
Message #18 : 88E6095 rev 2 Ethernet @ index 08Message #19 : MAC: 001f.9ee8.ffa1
Message #20 : 88E6095 rev 2 Ethernet @ index 07Message #21 : MAC: 001f.9ee8.ffa0
Message #22 : 88E6095 rev 2 Ethernet @ index 06Message #23 : MAC: 001f.9ee8.ff9f
Message #24 : 88E6095 rev 2 Ethernet @ index 05Message #25 : MAC: 001f.9ee8.ff9e
Message #26 : 88E6095 rev 2 Ethernet @ index 04Message #27 : MAC: 001f.9ee8.ff9d
Message #28 : 88E6095 rev 2 Ethernet @ index 03Message #29 : MAC: 001f.9ee8.ff9c
Message #30 : 88E6095 rev 2 Ethernet @ index 02Message #31 : MAC: 001f.9ee8.ff9b
Message #32 : 88E6095 rev 2 Ethernet @ index 01Message #33 : MAC: 001f.9ee8.ff9a
Message #34 : y88acs06 rev16 Gigabit Ethernet @ index 00 MAC: 001f.9ee8.ffa2
Message #35 :
Licensed features for this platform:
Message #36 : Maximum Physical Interfaces : 8
<--- More --->
Message #37 : VLANs                       : 3, DMZ Restricted
Message #38 : Inside Hosts                : Unlimited
Message #39 : Failover                    : Disabled
Message #40 : VPN-DES                     : Enabled
Message #41 : VPN-3DES-AES                : Enabled
Message #42 : VPN Peers                   : 10
Message #43 : WebVPN Peers                : 2
Message #44 : Dual ISPs                   : Disabled
Message #45 : VLAN Trunk Ports            : 0
Message #46 :
This platform has a Base license.
Message #47 :
Message #48 : Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0x0)
Message #49 :                              Boot microcode   : CNlite-MC-Boot-Cisco-1.2
Message #50 :                              SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03
Message #51 :                              IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
Message #52 :   --------------------------------------------------------------------------
Message #53 :                                  .            .
Message #54 :                                  |            |
Message #55 :                                 |||          |||
Message #56 :                               .|| ||.      .|| ||.
Message #57 :                            .:||| | |||:..:||| | |||:.
Message #58 :                             C i s c o S y s t e m s
Message #59 :   --------------------------------------------------------------------------
<--- More --->
Message #60 :
Cisco Adaptive Security Appliance Software Version 7.2(3)
Message #61 :
Message #62 :   ****************************** Warning *******************************
Message #63 :   This product contains cryptographic features and is
Message #64 :   subject to United States and local country laws
Message #65 :   governing, import, export, transfer, and use.
Message #66 :   Delivery of Cisco cryptographic products does not
Message #67 :   imply third-party authority to import, export,
Message #68 :   distribute, or use encryption. Importers, exporters,
Message #69 :   distributors and users are responsible for compliance
Message #70 :   with U.S. and local country laws. By using this
Message #71 :   product you agree to comply with applicable laws and
Message #72 :   regulations. If you are unable to comply with U.S.
Message #73 :   and local laws, return the enclosed items immediately.
Message #74 :
Message #75 :   A summary of U.S. laws governing Cisco cryptographic
Message #76 :   products may be found at:
Message #77 :   http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
Message #78 :
Message #79 :   If you require further assistance please contact us by
Message #80 :   sending email to [email protected].
Message #81 :   ******************************* Warning *******************************
Message #82 :
<--- More --->
Message #83 : Copyright (c) 1996-2007 by Cisco Systems, Inc.
Message #84 :                 Restricted Rights Legend
Message #85 : Use, duplication, or disclosure by the Government is
Message #86 : subject to restrictions as set forth in subparagraph
Message #87 : (c) of the Commercial Computer Software - Restricted
Message #88 : Rights clause at FAR sec. 52.227-19 and subparagraph
Message #89 : (c) (1) (ii) of the Rights in Technical Data and Computer
Message #90 : Software clause at DFARS sec. 252.227-7013.
Message #91 :                 Cisco Systems, Inc.
Message #92 :                 170 West Tasman Drive
Message #93 :                 San Jose, California 95134-1706
ciscoasa#

ASA 5505 Failed to unzip the Anyconenct Package

There is ASA 5505:
- 8.4(2) IOS
- FLASH: 128 Mb
- DRAM: 256 Mb
Requirements for 8.4(2) are acomplished:
For the ASA 5505, only the Unlimited Hosts license and the Security Plus license with failover enabled require 512 MB; other licenses can use 256 MB.
Are installed latest AnyConnect packeges for linux, some smatphones (each 4-5 MB). But for Windoes it's 21 MB and we got error "Failed to unzip the Anyconenct Package". In prior IOS version there was command cache-fs limit, by default it was 20 Mb. As i understand ASA now dinamically determines amount of cache memory and it's not enough.
Because of the increased size of the AnyConnect package from 4MB in AnyConnect 2.5 to 21 MB in AnyConnect 3.0, you may need to upgrade the ASA flash and memory card first.
If your ASA has only the default internal flash memory size or the default DRAM size (for cache memory) you could have problems storing and loading multiple AnyConnect client packages on the ASA. Even if you have enough space on the flash to hold the package files, the ASA could run out of cache memory when it unzips and loads the client images.
So there is a question, after DRAM upgrade to 512 MB will be there enough cache memory for Anyconnect packeges with total size 35-40 Mb?

I have having the same issue on an ASA-5510 with 256MB DRAM 256MB Flash. I do not have this issue on an ASA-5550 with 4GB DRAM 256MB Flash, so I'm guessing the issue is with the memory size.
Also, from: http://www.cisco.com/en/US/docs/security/vpn_client/anyconnect/anyconnect30/release/notes/anyconnect30rn.html
Flash and DRAM Requirements for Upgrade
Check for the space available before proceeding with the AnyConnect 3.0 upgrade. You can use one of the following methods to do so:
•CLI—Enter the show memory command.
asa3# show memory
Free memory:       304701712 bytes (57%)
Used memory:       232169200 bytes (43%)
Total memory:      536870912 bytes (100%)
•ASDM—Choose Tools > File Management. The File Management window displays flash space.
Because of the increased size of the AnyConnect package from 4MB in AnyConnect 2.5 to 21 MB in AnyConnect 3.0, you may need to upgrade the ASA flash and memory card first.
Caution The minimum flash memory required is 128MB for an ASA 5505; however, we strongly recommend 256 or preferably 512 MB. To support multiple endpoint operating systems and enable logging and debugging on the ASA, you will most likely need 512 MB of flash memory.
If your ASA has only the default internal flash memory size or the default DRAM size (for cache memory) you could have problems storing and loading multiple AnyConnect client packages on the ASA. Even if you have enough space on the flash to hold the package files, the ASA could run out of cache memory when it unzips and loads the client images. For internal memory requirements for each ASA model, see Memory Requirements for the Cisco ASA Adaptive Security Appliances Software Version 8.3 and Later. For additional information about the ASA memory requirements and upgrading ASA memory, see the latest release notes for the Cisco ASA 5500 series.

ASA 5505 as a SSL VPN Server and Easy VPN Client at the same time?

Is it possible to configure and operate the ASA 5505 as a SSL VPN server and Easy VPN Client at the same time? We would like to configure a few of these without having to purchase additional ASA 5505 and use a 2 device method (1 SSL VPN Server and 1 Easy VPN Client). Thanks in advance.

I don't think it is possible. Following links may help you
http://www.cisco.com/en/US/products/ps6120/products_configuration_guide_chapter09186a008068dabe.html
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008071c428.shtml

Save configuration in ASA 5505

Hi all, I have this issue, I save the configuration in the ASA 5505 using write memory or using copy run start but whe i unplug the power cord and plug it back in the ASA gets its factory default configuration.... then what i do is a copy start run to get the configuration active....
why is this so? even though i saved the config to flash ... regards!

You have incorrect boot register:
Please follow up the following document:
http://www.cisco.com/en/US/docs/security/asa/asa71/configuration/guide/trouble.html#wp1062992
You need to set up default value 0x1
HTH. Please rate this post if it was helpful. If this solves your problem, please mark this post as "Correct Answer"

ASA 5505 - Backup and restore to another device of same model and version

How can I backup the configuration of the ASA 5505 on 8.x and restore it to another ASA 5505 with same version? I have tried to save the running config to a file and then copy it to the new device and use the boot config: filename but it doesn't work. Or is there any other way to try? Thanks.

Thanks Andrew, I had tried it but I was having issues with the fact that I kept both ver 7 and ver 8 of the OS images on the flash. So it booted from the first found (ver 7) and creating confusion for me as the config file was for ver 8.
I noticed that it keeps the 192.168.1.1 IP even though in the config file it has another IP assigned. Is there other things that I need to check that do not change apart the IP address?
Thanks.

CISCO ASA 5505 Split Tunnel DNS with Site to Site VPN

I have a working configuration for Site to Site VPN between our head office and a private AWS VPC instance.
The tunnel is active and I can ping the IP address of the remote network and connect to the remote machines using the IP address, but we need to use the FQDN and not the IP. We have a DNS server set up in AWS for any DNS queries for the remote domain name.
My question is whether or not the ASA 5505 supports a DNS split tunnel for Site to Site VPN and how it can be configured.
I can not find where I can interogate the DNS query to be redirected to the VPN tunnel when our domain name is used in a DNS query. Thus, any pings I try with the FQDN of our servers in AWS are failing as they are going to the default DNS, which is the internet.
Can any one point me in the right direction on how to configure this DNS rewrite so that we can access our AWS private cloud using FQDN from our AWS domain rather than an IP address?

Jose, your fix to problem 1 allows all access from the outside, assuming you applied the extended list to the outside interface. Try to be more restrictive than an '...ip any any' rule for outside_in connections. For instance, this is what I have for incoming VOIP (access list and nat rules):
access list rule:
access-list outside_access_in extended permit udp any object server range 9000 9049 log errors
nat rule:
nat (inside,outside) source static server interface service voip-range voip-range
- 'server' is a network object *
- 'voip-range' is a service group range
I'd assume you can do something similar here in combination with my earlier comment:
access-list incoming extended permit tcp any any eq 5900
Can you explain your forwarding methodology a little more? I'm by no means an expert on forwarding, but the way I read what you're trying to do is that you have an inbound VNC request coming in on 5900 and you want the firewall to figure out which host the request should go to. Or is it vice-versa, the inbound VNC request can be on port 6001-6004 ?

1 Website Blocked under ASA 5505 - Why?

I have had the ASA 5505 set up for over 5 years, no problems. For some reason there is one website that my users cannot access. www.communityservicepartners.org (173.161.122.9). I have no idea why it is being blocked. Can someone assist? Thanks
------------------ show running-config ------------------
: Saved
ASA Version 7.2(2)
hostname ciscoasa
domain-name mrsh.net
enable password <removed>
names
interface Vlan1
nameif inside
security-level 100
ip address 10.10.10.1 255.255.255.0
ospf cost 10
interface Vlan2
nameif outside
security-level 0
ip address 173.15.74.73 255.0.0.0
ospf cost 10
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
passwd <removed>
time-range All
periodic daily 0:00 to 23:59
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
domain-name mrsh.net
same-security-traffic permit intra-interface
access-list mrsh_nat0_outbound extended permit ip 10.10.10.0 255.255.255.0 10.10.20.0 255.255.255.192
access-list DefaultRAGroup_splitTunnelAcl standard permit 10.10.10.0 255.255.255.0
access-list DefaultRAGroup_splitTunnelAcl standard permit host 173.15.74.73
access-list DefaultRAGroup_splitTunnelAcl standard permit host 173.15.74.74
access-list outside_access_in remark Implicit rule
access-list outside_access_in extended permit ip any any
access-list inside_access_in extended permit ip any any
pager lines 24
logging enable
logging console debugging
logging buffered notifications
logging trap debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool Pool 10.10.20.10-10.10.20.50 mask 255.255.255.192
ip local pool Pool2 20.20.20.10-20.20.20.50 mask 255.255.255.192
ip verify reverse-path interface inside
ip verify reverse-path interface outside
no failover
monitor-interface inside
monitor-interface outside
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list mrsh_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
access-group inside_access_in in interface inside
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.10.10.1 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout uauth 0:05:00 absolute
port-forward RDP 3389 173.15.74.73 3389 RDP
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
vpn-access-hours value All
vpn-simultaneous-logins 20
vpn-idle-timeout none
vpn-session-timeout none
vpn-filter none
vpn-tunnel-protocol IPSec l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl
http server enable
http 10.10.10.100 255.255.255.255 inside
http 10.10.10.2 255.255.255.255 inside
http redirect inside 80
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp identity address
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime none
crypto isakmp nat-traversal 20
crypto isakmp ipsec-over-tcp port 10000
tunnel-group DefaultRAGroup general-attributes
address-pool Pool
address-pool Pool2
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *
isakmp keepalive disable
tunnel-group DefaultWEBVPNGroup webvpn-attributes
nbns-server 192.168.2.109 master timeout 2 retry 2
tunnel-group MRSH type ipsec-ra
tunnel-group MRSH general-attributes
address-pool Pool
default-group-policy DefaultRAGroup
tunnel-group MRSH ipsec-attributes
pre-shared-key *
tunnel-group MRSH ppp-attributes
authentication pap
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
dhcpd address 10.10.10.2-10.10.10.230 inside
dhcpd enable inside
policy-map type inspect http http://192.168.2.100/mrshproject
parameters
protocol-violation action drop-connection
webvpn
svc enable
port-forward RDP 3389 173.15.74.73 3389 RDP
cache
disable
no cache-compressed
prompt hostname context
compression svc
Cryptochecksum:278c4c6bf9defa17d7201e040655e9a7
: end

yes I am trying to access by name.
Here is my oputput:
Result of the command: "packet-tracer in inside tcp 10.10.10.10 12345 173.161.122.9 80"
Phase: 1
Type: FLOW-LOOKUP
Subtype:
Result: ALLOW
Config:
Additional Information:
Found no matching flow, creating a new flow
Phase: 2
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   173.0.0.0       255.0.0.0       outside
Phase: 3
Type: ROUTE-LOOKUP
Subtype: input
Result: ALLOW
Config:
Additional Information:
in   10.10.10.0      255.255.255.0   inside
Phase: 4
Type: ACCESS-LIST
Subtype: log
Result: ALLOW
Config:
access-group inside_access_in in interface inside
access-list inside_access_in extended permit ip any any
Additional Information:
Phase: 5
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 6
Type: NAT
Subtype:
Result: ALLOW
Config:
nat (inside) 0 access-list mrsh_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
match ip inside any outside any
    dynamic translation to pool 1 (173.15.74.73 [Interface PAT])
    translate_hits = 1010100, untranslate_hits = 497459
Additional Information:
Dynamic translate 10.10.10.10/12345 to 173.15.74.73/57304 using netmask 255.255.255.255
Phase: 7
Type: NAT
Subtype: host-limits
Result: ALLOW
Config:
nat (inside) 0 access-list mrsh_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
match ip inside any inside any
    dynamic translation to pool 1 (No matching global)
    translate_hits = 0, untranslate_hits = 0
Additional Information:
Phase: 8
Type: IP-OPTIONS
Subtype:
Result: ALLOW
Config:
Additional Information:
Phase: 9
Type: FLOW-CREATION
Subtype:
Result: ALLOW
Config:
Additional Information:
New flow created with id 1034245, packet dispatched to next module
Result:
input-interface: inside
input-status: up
input-line-status: up
output-interface: inside
output-status: up
output-line-status: up
Action: allow

ASA 5505 vpn/OWA issue

I have a client that is running Win2003 Server R2 with Exchange Server 2003. OWA was setup and clients could connect to their exchange mailbox from the internet with no problems.
We recently configured vpn on the ASA 5505 and now no-one can connect to OWA since that time.
Any thoughts?

Have you been using the ASDM to configure the VPN? In that case, you may have removed the required portforwarding or modified the access-list that allows traffic from the outside.
regards,
Leo

OWA not accessible after setting up vpn through ASA 5505

I have a client that is running Win2003 Server R2 with Exchange Server 2003. OWA was setup and clients could connect to their exchange mailbox from the internet with no problems.
We recently configured vpn on the ASA 5505 and now no-one can connect to OWA since that time.
Here is what I have for a configuration.
Any thoughts?

I thought OWA uses tcp port 80 by default, or 443 if you use https. Ignore the rest if this fact is wrong. Otherwise ...
In your config there is nothing to allow the www traffic in the access-list outside_access_in
access-list outside_access_in extended permit tcp any interface outside eq 80
and no static nat for this
static (inside,outside) tcp interface 80 192.168.0.254 80 netmask 255.255.255.255
I think these must have got deleted when you made the other changes ? Hope this helps.

Problems upgrading ASA 5505 memory

I am trying to get experience with 8.4 code on my 5505. I purchased a Cisco 512MB memory upgrade and installed it. It booted up once and I thought I was ok. I then looked down and noticed that all lights were blinking on the front panel and I had no console access.
Since I dont have smartnet on my personal 5505, calling TAC for help isnt an option. That is why I spent extra money on Cisco memory but it looks that didnt help. I am assuming all blinking lights isnt a good thing but I havent been able find an explanation.
I will try reseating the memory to see if that is the problem. I put the ASA on an anti-static mat and had it and myself properly grounded.
If this doesnt fix it, I will return the Cisco memory to the vendor and go back to the original installed memory. The ASA 5505 worked fine on 8.2.5.
Would appreciate any suggestions,
Ron

Ronald and James,
It has been over a month since you posted, so perhaps your issue was resolved. I actually experienced the exact same issue with my personal ASA 5505 today following an upgrade to 512MB. What really surprised me was James' comment that his worked for about 12 hours and stopped. That's exactly what happened to me today. It might have been 13 hours, but it was definitely in the ballpark.
The first thing I did was just disconnect power and re-connect the power to see if it magically went away. (I've never had to cycle the power on my ASA before, so I was not hopeful this would work. In fact, I was glad it did not work, as that would concern me even more.)
The next thing I did was disconnect everything, open the case, remove the RAM, blow out all of the dust using compressed air, and then re-install the RAM. So far, so good, but it has only been 15 minutes.
I'll keep an eye on this, obviously, but I am nonetheless curious to hear more about your situations. Were you able to resolve the problem permanently or were you unable to make the upgrade to 512MB?
UPDATE - My ASA continued to have issues with the new RAM module. It turned out to be a defective SIMM. I contacted the seller and returned the defective SIMM. They sent a new one and it works just fine.

PNRP though the ASA 5505

Similar Messages

Maybe you are looking for