Preserve remote vlan with Q in Q

One of our remote sites needs to move their servers to our datacenter. We need to do this while maintaining the server vlan of the remote site so the server's addresses do not change when they are
moved here.
Currently the remote site is connected over a point to point fiber link. There is a 4506 on the remote site end, with a gig link configured with a 30 bit address (i.e. 10.0.1.1 255.255.255.252).
The other end connects to an intermediate site of ours into a 6509 with a corresponding address defind on the port (i.e. 10.0.1.2 255.255.255.252). The 6509 in turn is connected to our datacenter 6513 over a trunk port (connected by fiber).
We've since had another fiber line run between the remote site and our datacenter where the 6513 is housed. We can now eliminate the intermediary link from the 4506 to the 6509 and connect the remote site's 4506 directly into our 6513. How do we do this in a way that preserves their vlans (and therefore their address ranges) so that we can move their servers over here with their addresses intact?
I've been looking at Q in Q vlan stacking but I'm not quite sure this is the right solution. I've also looked at a variation of Q in Q that uses that subinterfaces for vlan mapping from
customer to service provider vlans, but I'm not sure this is the right solution either.
What is the best way to do this? Please ask questions if more information is needed.

If you really have the sites connected via fiber that you light with no carrier equipment providing an IP interface, your switches can just VLAN trunk to each other.
If that's not possible, have you considered using tunnel interfaces? You only said you need to maintain the server's IP addresses (though that does lead one to question why theyt are accessed via IP address and not DNS name... but some things we can't always control), not their Layer 2 broadcast domain (the VLAN).
See http://www.cisco.com/en/US/customer/products/sw/iosswrel/ps1826/products_configuration_guide_chapter09186a00800d9b65.html#xtocid193623 for details on configuring tunnels.
Hope this helps, please rate helpful posts.

Similar Messages

Remote APs with multiple vlan / dhcp

On one of our 5508 controllers we have approx 40 APs, about 20 local and 20 flexiconnect. Until now we have only had one vlan on the flexiconnect APs, but our local APs have several SSIDs connecting to different Vlans and assigned different dhcp addresses correctly.
We now have the need to have multiple SSIDs on some sites being assigned different IPs.
I have created the interfaces, with the correct ip and dhcp server, linked with the correct AP group. The SSID is shown and can be connected, but the original ip is being assigned and not the new range.
I have not yet created any security policies so the new range has full access to the entire network and the controller can ping the new remote vlans.
If i hard connect to the switch on the new vlan, I am assigned the correct new IP range, so this is working.
I cannot see why devices connected to the new SSID are not being assigned the correct IP range.

You need to review the FlexConnect configuration guide. You need to trunk the ap port if more than one vlan is required, you also need to enable FlexConnect local switching in the WLAN, you need to also define the WLAN to vlan mapping on each FlexConnect AP.
It varies depending if you want to place traffic locally at the site or tunnel it back.
https://supportforums.cisco.com/docs/DOC-24082
Sent from Cisco Technical Support iPhone App

RV016 VPN Gateway to Gateway problem to add remote vlan

Hi to all i have a little problem with RV016.I have one site to site vlan ipsec and i would like to add a remote vlan to the tunneling but RV has only three options
-IP
-Subnet
-IP Range
Now the remote lan for vpn is 192.168.10.0/24 and i would like to add 10.1.1.0/24
Can someone help me ?

Hi Ckioroglou,
I'm need more information regarding the VPN on both site but from I understand I can suggest the following
we can have three solution
- Create a second Tunnel and use the local remote as Subnet and configure the Vlan Subnet (10.1.1.0/24)
Or
- If it's possible to change th Vlan to 192.168.x.x and we can have only one Tunnel with remote subnet class B (/16)
Or
- We can use only one IPsec VPN tunnel where the Remote Local is setup to 0.0.0.0 and mask 0.0.0.0 and other site the local network 0.0.0.0 and mask 0.0.0.0 BUT
In this situation we will have full tunnel IPsec Site to Site it mean's all the traffic include Internet traffic will pass through the VPN
Please rate the post or mark as answered to help other Cisco Customer
Best regards
Mehdi

Unable to pair Apple Remote App with iTunes

I am running a Toshiba Satellite L505D-S5965 with Windows Vista SP 2. My iTunes software is 8.2.1.6, and my iPhone 3GS is running OS 3.0.1 (7A400). Both the Satellite and iPhone are connected to the same WiFi local network, and yet the App "Remote" by Apple Software is unable to communicate with iTunes to allow the entry of the four digit code to establish control of the iTunes library. Shortly after purchasing the iPhone 3GS I purchased the Satellite, but in the couple of weeks between the purchases the Remote App worked fine on my Gateway running Windows XP SP2. I have been through Apple Telephone support twice, and have really run one of the technicians through the mill researching possible solutions. I have visited an Apple Store Genius, who could find no reason for the problem. The iPhone and Remote App worked perfectly well on the store's WiFi and Mac, but his iPhone also wouldn't work with my laptop. I have been through Kaspersky's technical support system to ensure that there isn't a firewall issue. They have assured me, after reviewing logs from my laptop, that this is not the case. I even went so far as to uninstall all my Kaspersky product, but the Apple Remote App still would not function properly. I have updated the router's firmware, and checked that the laptop's wireless card is running the latest driver. At this point I can't think of anything else to try but would really appreciate any suggestions. Thanks, Steve

Monday 7th Jan.
Just to say that Apple did call me this am to discuss the problem on foot of a call I made last week.
In the meantime the remote worked with both a 2007 IMac and a 2009 laptop but not on the m-mini.
When I tried pairing this morning during the call by pressing Menu and next together it paired.
The change is very subtle, it just says paired in the advanced section of the security et sl section as referred before, with a fleeting 2 intersecting rings icon.
The big difference is that Front Row is gone....
The remote only works to a limited degree within some apps such as iTunes and iPhotos.
In theory it controls the volume in iTunes but as of now for me it doesnt....:( need to look more.
As to what the problem was:
It seems there is a set of keyboard combinations that can be used to force a reset the ID of the remote, the suggestion is MAYBE that by getting it to work on the iMac and laptop in some way reset the ID.
This stuff is WAY beyond my skill level:)
I did impress upon Apple the need to look at the issue in threads like this....
Message was edited by: qazxsw52

Remote app with Apple TV

I use the Remote app with both an iPad and iPhone to control my first gen Apple TV. This works fine except for one thing. When I select "Apple TV" as the library, using an iPhone I have access to all my library including Podcasts. When I run the same app on my Ipad, still selecting "Apple TV" as the library, no Podcasts come up on the iPad to select - the category is completely missing.
Has anyone else seen this issue ? Are they still there but hidden somewhere else ? Bear in mind I keep no content on the Apple TV - it is effectively just acting as a wireless device to get the signal to my TV.

Literally nothing happens. I click the done button and hear a beep. Over and over again.
On the phone, the passcode is still displayed.
Thank you for your help.

How does Remote work with Apple TV?

How does Remote work with Apple TV?
1. Does Remote, "Play" the music that resides on your iPod Touch>Apple TV>Home Speakers.
OR
Does Remote "Control" the music that resides on Apple TV HD>Home Speakers.
(If so... say you have a iPod Touch that only holds 8GB's but your music collection on your Apple TV exceeds that amount.
Will Remote still "Control" the larger music collection on Apple TV or your computer?)
2. Will iPod Wifi work on a patio outside a home to control Apple TV inside the home?
thank you in advance, Tom

Remote is a way to control iTunes on either your computer or Apple TV using a WiFi connection. See this article for complete instructions.

Why isn't my remote working with my Apple TV?

I have had my Apple TV a while now and I noticed a while back that the remote wasn't working with my TV. I assumed that I needed to replace the batteries so I downloaded the Remote app with my iPhone. Once I replaced the batteries, the remote still didn't work with my Apple TV. I reset my Apple TV to factory settings the other day because I noticed that my newer music that I had purchased recenlty wasn't showing in my music. Once I reset it, there was a screen that came up to set the TV up again but since I can't use the remoted I can't choose English as my language. In small writing at the bottom, it says I can use my iPhone or iPad as a remote by searching for my Apple TV in the bluetooth settings. When I try that on my iPhone and iPad neither of them show the TV as being able to pair with it. Has anyone else had a similar issue or can think of anything that I can do? I tried holding the Menu and left keys, I have held just about all the keys for more than 6 seconds and nothing ever happens. Thank you in advance for any suggestions.

You can use your IOS device to do initial setup on an Apple TV, but you won't be able to use it as a remote as that also requires home sharing to be enabled. I would take it to Apple to test the remote and/or get a replacement.

If I were to purchase the Apple Remote Desktop with Unlimited licenses, would I be able to install the client software on each of there computers/laptops and have them remote desktop into the server?

I have several friends and family who are looking for a central place to access information from ( Pictures, home movies etc ). So I am considering setting up an OSX Lion Server. There are some other things I can use it for as well.
Here is my question:
If I were to purchase the Apple Remote Desktop with Unlimited licenses, would I be able to install the client software on each of there computers/laptops and have them remote desktop into the server? Or would I have to install the Admin software on each? Do they intend it to be used strictly as one admin to access many clients?
I always could set up a network drive so they can log in and just see the folders they have created with space on the server I provide them. But I want them to be able to log an and actually use it as a Remote Desktop.
Thanks,
Eric

Dave,
Thanks for the feedback. I understand that ARD is meant for Remote Administration, but I was not sure if it could be used for my purpose as well. The reason I was looking to do it this was was because I read several articles online about security and performance issues with setting up VNC and activating screen sharing. Unless I am misunderstood.
As far as people's activities on the server, mostly it is going to be used as a place for them to store their media. I will only allow own person ( Who I trust and I know wont botch the server ), to run applications. Everyone else will be restricted to uploading and downloading content to their designated account on the server as well as a community share on the server.
I appreciate your help.
Thanks,
Eric

How can you run a command with elevated rights on a remote server with invoke-command ?

I am trying to run a script on a remote server with invoke-command. The script is starting and is running fine, but the problem is that it should be running with elevated rights on the remote server. On the server where I start the invoke-command, my account has the necessary rights.
The server were I launch the invoke-command is a W2K8 R2. The remote box is a W2K3 with powershell v2.0 installed.
When I launch the script on the remote-box from the command line, I don't get the access denied's.
Is there a way to do this ?
Thanks in advance

The script that I want to run is to install the windows updates. I get an access denied on the download of the updates.
When I execute the script on an W2K8 box, (not remotely) and I run it with non-elevated rights, I get the same error.
The script is running fine when it is launched on W2K3 box locally with a domain account that has local admin rights, or on a W2K8 R2 server with a domain account that has local admin rights, but with elevated rights.
Thanks in advance for your help.
#=== start script ====
param($installOption="TESTINSTALL",$rebootOption="NOREBOOT")
Function Show-Help
Write-Host ""
Write-Host "SCRIPT: $scriptName <installOption> <RebootOption>"
Write-Host ""
Write-Host "DESCRIPTION: Installatie van WSUS updates op de lokale server"
Write-Host ""
Write-Host "PARAMETERS"
Write-Host " -installOption <[INSTALL|TESTINSTALL]>"
Write-Host " -rebootOption <[REBOOT|NOREBOOT|REBOOT_IF_UPDATED]>"
Write-Host ""
Write-Host "EXAMPLE:"
Write-Host "$ScriptName -installOption INSTALL -rebootOption REBOOT_IF_UPDATED"
Write-Host "$ScriptNAme INSTALL NOREBOOT"
Write-Host ""
Write-Host "Indien beide parameter weggelaten worden zijn de defaultwaarden :"
Write-Host " installOption=TESTINSTALL "
Write-Host " RebootOption=NOREBOOT"
Write-Host ""
Exit
#Include alle globale variablen
$CEIF_WIN_PATH = (get-content env:CEIF_WIN_PATH)
$includeFile=$CEIF_WIN_PATH + "\Scripts\include_win.ps1"
. $includeFile
#initialiseer error count
$errcnt=0
$scriptName=$MyInvocation.MyCommand.Name
#argumenten controleren
$arrInstallOption= "TESTINSTALL", "INSTALL" # Mandatory variable with predefined values
If (!($arrInstallOption –contains $installOption)){ Show-Help }
$arrRebootOption = "REBOOT", "NOREBOOT","REBOOT_IF_UPDATED" # Mandatory variable with predefined values
If (!($arrRebootOption –contains $rebootOption)){ Show-Help }
#Logfile opbouwen
$logfile = get-logfileName($MyInvocation.MyCommand.Name)
Log-scriptStart $MyInvocation.MyCommand.Name $logfile
function Get-WIAStatusValue($value)
switch -exact ($value)
0 {"NotStarted"}
1 {"InProgress"}
2 {"Succeeded"}
3 {"SucceededWithErrors"}
4 {"Failed"}
5 {"Aborted"}
function boot-server()
if ($installOption -eq "TESTINSTALL")
logger "TESTINSTALL : - Reboot local Server" $logfile
else
logger " - Reboot local Server" $logfile
$thisServer = gwmi win32_operatingsystem
$thisServer.psbase.Scope.Options.EnablePrivileges = $true
$thisServer.Reboot()
$logmsg="Install option = " + $installOption + ", RebootOption = $rebootOption"
logger "$logmsg" $logfile
logger "" $logfile
logger " - Creating WU COM object" $logfile
$UpdateSession = New-Object -ComObject Microsoft.Update.Session
$UpdateSearcher = $UpdateSession.CreateUpdateSearcher()
logger " - Searching for Updates" $logfile
$SearchResult = $UpdateSearcher.Search("IsAssigned=1 and IsHidden=0 and IsInstalled=0")
logger " - Found [$($SearchResult.Updates.count)] Updates to Download and install" $logfile
$Updates=$($SearchResult.Updates.count)
logger "" $logfile
foreach($Update in $SearchResult.Updates)
if ($Update.EulaAccepted -eq 0)
$Update.AcceptEula()
# Add Update to Collection
$UpdatesCollection = New-Object -ComObject Microsoft.Update.UpdateColl
$UpdatesCollection.Add($Update) | out-null
if ($installOption -eq "TESTINSTALL")
else
# Download
logger " + Downloading Update $($Update.Title)" $logfile
$UpdatesDownloader = $UpdateSession.CreateUpdateDownloader()
$UpdatesDownloader.Updates = $UpdatesCollection
$DownloadResult = $UpdatesDownloader.Download()
$Message = " - Download {0}" -f (Get-WIAStatusValue $DownloadResult.ResultCode)
if ($DownloadResult.ResultCode -eq 4 )
{ $errcnt = 1 }
logger $message $logfile
# Install
logger " - Installing Update" $logfile
$UpdatesInstaller = $UpdateSession.CreateUpdateInstaller()
$UpdatesInstaller.Updates = $UpdatesCollection
$InstallResult = $UpdatesInstaller.Install()
$Message = " - Install {0}" -f (Get-WIAStatusValue $InstallResult.ResultCode)
if ($InstallResult.ResultCode -eq 4 )
{ $errcnt = 1 }
logger $message $logfile
logger "" $logfile
#Indien er een fout gebeurde tijdens download/installatie -> stuur mail naar windowsteam
if ( $errcnt -gt 0 )
logger " - Fout tijdens de uitvoering van script -> send mail" $logfile
$mailSubject=$MyInvocation.MyCommand.Name
$msg = new-object Net.Mail.MailMessage
$att = new-object Net.Mail.Attachment($logfile)
$smtp = new-object Net.Mail.SmtpClient($smtpServer)
$msg.From = $mailFrom
$msg.To.Add($mailTo)
$msg.Subject = $mailSubject
$msg.Body = “Meer details in attachement”
$msg.Attachments.Add($att)
$smtp.Send($msg)
#Moet de server herstart worden ?
if ($rebootOption -eq "REBOOT_IF_UPDATED" )
if ($Updates -gt 0)
#Reboot the server when updates are installed
boot-server
elseif ($rebootOption -eq "REBOOT")
#reboot the server always
boot-server
else
#Do not reboot the server
logger "Do not reboot the server" $logfile
Log-scriptEnd $MyInvocation.MyCommand.Name $logfile
exit 0

Remote Site with its own CUCM Sub#2 and Router network failed and the site didnt keep its phones active, need some assistance

I have a Pub and 2 Sub's. Sub #1 is with the Pub, at the main site it is our TFTP server, Sub #2 is at a remote site with about 100 users along with a router and 2 PRI's for outbound calls. We had a network failure between the main site and the remote site and all phone lost their registration with the system until we were able to get the network back up. Currently the network is up in a crippled state on a 1 T-1 link while we troubleshoot the bigger issue with our 6mb pipe, however Sub #2 and its associated router arent talking with the PUB or other Sub. I'm still getting alerts every 30 minutes stating they are the server is down. I'm sure once the network is corrected this will bring everything back on line. My question is how can I prevent in this in the future. I need this site to be stand alone if the network goes down again. I was told by our vendor that if we had a subscriber at each site then we would need SRST licensing. I know something needs to be configured to make it all work, I'm just not sure what.

I already have a group at the site but it includes both the Pub and Sub from the main site as well as the Sub from the remote site. I would only have to remove the Sub from the main site, problem is I currently only have 1 TFTP server it runs on SUB #1, should I make SUB#2 a TFTP server as well and the phones are setup for DHCP at the main site, I'm going to need to have a DHCP server setup at the remote site as well. Correct?

It´s possible to use the "Remote" app with Itunes and a Nokia E72 with Joikuspot installed only? Or I´ll need to buy a modem Wifi?

It´s possible to use the "Remote" app with Itunes and a Nokia E72 with Joikuspot installed only? Or I´ll need to buy a modem Wifi?
I was using "remote" with a D-link modem, that works fine at my iPad. But now I´m using only the cell phone as modem 3G, and don´t want to intall a router to put new cables at my notebook.

What?
You want to control iTunes on your computer using the Remote app on your iPad?
And you want to connect the iPad and computer through your Nokia?
No, this will not work.
Just create a network with your notebook.

Unable to syndicate same Remote System with differnt value

Hi,
I am working on MDM 7.1 SP05 and I have the following issue with syndication:
I have a remote system table (Key Enabled) with System as Non-Qualifier and value as Qualifier and I have values in the MDM Datamanager as
MDM ID, Remotesystem (Multivalue Qualifier Table with Key Enabled)
111,((Qual1-Key,Val1),(Qual1-Key,Val2),(Qual1-Key,Val3))
When I syndicate I see only one value as 111, (Qual1,Val3)... But I want to have all the Qualifiers-Key with multiple values.. Where as in MDM 5.5 I can see all the Qualifiers with out any issues..Is this a restriction in MDM 7.1?
If I map System instead of Remote Key of Qualifier Table then I can see multiple times of same remote system with appropriate values.. But If I map remote key then I see the consolidated/the latest system-remote key wiht value... But I want system-remote key value appear multiple times...
Thanks alot
Rajeev

I am using customised...
Did you tried syndicating Remote key of that table or the field of the Qualifer table?
I am able to syndicate out with the system field and values.. But I want to syndicate out the multiple values wiht remote key of the table..
As mentioned Remote keys are AAA and BBB for System Sys1 and Sys2..
First I imported remote system table with Sys1 and Sys2 with remote Keys as AAA and BBB. then along wiht main table record I imported Sys1 and Sy2...
While Syndicating I want to syndicate AAA and BBB values along with Value field...
Suppose:
I have data :
MDM ID, RemoteSystem(System, Value)
111, ((Sys1,Val1),(Sys1,Val2),(Sys1,Val3),(Sys2,Val1))
Remote Keys for Sys1AAA and Sys2BBB
In the Syndication Manager I mapped as below: RemoteSystems RemoteKey and value are mapped to target...
RemoteSystem
--RemoteKey
System(DFNQ)
--Value(Qualifier)
I mapped RemoteKey and Value to the target fields.. Which is a XML output..
<REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val3</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>BBB</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val1</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
</REMOTE_SYSTEM>
Where I need the following Output:
<REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val1</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val2</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>AAA</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val3</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
- <Z_MDM_REMOTE_SYSTEM >
<Z_MDM_SYSTEM_NAME>BBB</Z_MDM_SYSTEM_NAME>
<Z_MDM_VALUE>Val1</Z_MDM_VALUE>
</Z_MDM_REMOTE_SYSTEM>
</REMOTE_SYSTEM>
Any inputs.
Thanks
Rajeev

DOES THE APPLE REMOTE WORK WITH THE IPOD TOUCH..? WITHOUT A DOCK..

HI
DOES THE APPLE REMOTE WORK WITH THE IPOD TOUCH 5TH GEN..? WHITHOUT A DOCK..??
THANKS ANYONE

This Apple remote requires a dock since this remote uses IR and the iPod does not ha IR capibility,.
Manufacturer Information
Apple Remote with iPod and iPhone: Please note a Universal Dock is required in order to use the Apple Remote with your iPhone or iPod.
http://store.apple.com/us/product/MC377LL/A/apple-remote?

Does the apple remote work with the ipod touch 4th gen?

Does the apple remote work with the ipod touch 4th gen?

Yes, but it also requires Apple's Universal Dock to go along with it. Otherwise, it is useles.
B-rock

WIn 7 PRO to Win 7 PRO Remote Desktop with matching 1920x1080 Dual Monitors

I have done quite a bit of looking and still do not know if WIn 7 PRO can connect to a to Win 7 PRO with Remote Desktop with matching 1920x1080 Dual Monitors. It seems like it cannot use dual monitors by the HELP file. But
then why does it have "Use all of my monitors for the remote session" as a selection in the Connection settings ? Just what is the real answer ? Both systems are 64 bit. If the answer is YES. Please tell me how !

Hello i-wonder-why,
To use this Remote Desktop Multimon feature, you must:
1.Connect using the Remote Desktop Client 7.0 (mstsc.exe) available initially on Windows 7/Windows Server 2008 R2.
2.Enable Multimon using one of the three methods described below:
a. Click “Use all monitors for the remote session” in the client (mstsc.exe) window.
b. Use the “/multimon” switch on the mstsc.exe command line.
c. Add “Use Multimon:i:1” to the RDP file.
image
3.Connect to a computer running Windows 7 or Windows Server 2008 R2.
For more information, please refer to the following article.
http://blogs.msdn.com/b/rds/archive/2009/07/01/using-multiple-monitors-in-remote-desktop-session.aspx
Best regards,
Fangzhou CHEN
Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Preserve remote vlan with Q in Q

Similar Messages

Maybe you are looking for