Prevent called party number changes on outgoing call to PSTN
Hello Folks,
we have CUCM 9.1 with SIP trunks to cisco 2951 connected to the PSTN either by BRI or PRI module.
we have implemented internal full e.164 (including +) dialplan
when we do an outgoing call (via SIP trunk and 2951) the phones first shows the full e.164 number i.e. +4970366431002. As soon as the call goes out to the PSTN, the display changes to the number format in which the 2951 sends the call to the ISDN.
Because in ISDN there is no +, the gateway translates the called number to (in this example) 70366431002 TON national. and sends this back to CUCM in the Session progress Remote-Party-ID value (see output from debug on the 2951 below)
how can we prevend that the phone is showing this number instead of the original number?
thanks a lot - mat
debug isdn q931
Calling Party Number i = 0x1081, '497142500290'
Plan:Unknown, Type:International
Called Party Number i = 0xA1, '70346431002'
Plan:ISDN, Type:National
debug ccsip messages:
Sent:
SIP/2.0 183 Session Progress
Via: SIP/2.0/TCP 10.1.60.2:5060;branch=z9hG4bK3b5c02cb10b0d
From: <sip:[email protected]>;tag=3018449~a209bda8-de62-43dc-9e6a-6ebfafc31bde-46236303
To: <sip:[email protected]>;tag=ED03BF44-10BA
Date: Mon, 02 Sep 2013 12:41:56 GMT
Call-ID: [email protected]
CSeq: 101 INVITE
Allow: INVITE, OPTIONS, BYE, CANCEL, ACK, PRACK, UPDATE, REFER, SUBSCRIBE, NOTIFY, INFO, REGISTER
Allow-Events: telephone-event
Remote-Party-ID: <sip:[email protected]>;party=called;screen=no;privacy=off
Contact: <sip:[email protected]:5060;transport=tcp>
Hi,
any calling or called transformation in the route pattern appears in the screen.
you can discard the 9 in the route pattern and add prefix 9 in the route list level.
for the 2nd point there is a service parameter in the call manager to keep the original dialed number
HTH
Anas
don't forget to rate the helpful posts
Similar Messages
-
Calling Party Number empty when the call gets to Route List
Caller id is not showing up on 911 calls. Using Dialed Number Analyser I can see the calling Party Number fine through the route pattern. Then in the Route List it comes up empty. Nothing in the config of the Route List is restricting or manipulating the calling number. Use calling party's external phone number mask is set to on. We are using Standard Local Route Groups.
Thanks in advance for your help.Do you see the caller ID on the GW in debugs?
What type of circuit is used for this call? If PRI can you provide "debug isdn q931"?
Chris -
Redirect Calls Based on Calling Party Number
Hi All,
I am looking for a method to redirect inbound PSTN calls based on the calling party number. I can do this in CUCM 9 or IOS. I find plenty of documentation out there on blocking calls by calling party number but nothing on redirecting.
My situation is this. We are a large company and often get request from users to block calls from annoying or harassing numbers. Rather than block them I would like to drive them into a mailbox where the caller can attempt to find a resolution if they feel the calls was blocked in error.
Has anyone else attempted something like this?
ThanksHi Jerold,
If you are using CUCM 8.x and above, you can re-direct the call on the basis of the calling party number.
The configuration is very similar to block a call that uses the new feature added in CUCM 8.x and above (
Route Next Hop By Calling Party Number). The step 8 in the following document explains how to handle the call when the call has be routed by the calling party number. The translation pattern is configure with Route Option as "Block this pattern".
https://supportforums.cisco.com/docs/DOC-18367
In order to re-direct the call, you can configure the Route Option with "Route this pattern" and specify the desired destination pattern under "Called party Transformation Mask". Also, make sure to add the appropriate CSS to be able to route the call.
HTH,
Jagpreet Singh Barmi -
Change Ship to party number for outbound delivery
Hi guys
I have a problem
We need to change Ship to party number for outbound delivery
Any suggestions
Any Table level changes posibility???
Thanks
SAP MMHi,
You cannot change the ship to party in delivery, nor should you change it.
If you really want to change the SH in delivery, please delete the delivery (after cancelling the picking) and then go to sales order in change mode and then change the ship to party there. After doing this, create the delivery once again with the new SH.
It is not advisable even through programatically to change SH in delivery. This will have lot of implications in the further processes like PGI, Proof of Delivery and so on. -
Spa3102 would not forward a voip call to pstn line
Good morning.
I've done the implementation provided here http://community.linksys.com/t5/VoIP-Adapters/SPA-3102-and-softphone-to-
make-calls-via-pstn-line/td-p/326390 .
It is a way to use for outgoing calls a given pstn line from anywhere I have internet (voip to pstn).
The spa3102 is connected to a router (with an active DHCP server and ip 192.168.1.1) from where it takes the internal
ip (192.168.1.3).On the same network is also a computer , connected to the router ( with ip 192.168.1.2). The spa3102
is set to bridge mode and thus inactivates the function of the router (on SPA3102), and it functions as a simple
network device . I have done port forwarding (from the router) to 192.168.1.3 (SPA3102) for the port 5061 (PSTN
LINE) ( but for 5060 for the LINE 1 also). I want to make calls from a voip softphone (x-lite 4) to the SPA 3102 and
this to forward the voip calls to PSTN line to which it is connected. In x-lite the SPA3102 is set as a proxy so that
i can type the phone number I want to call without being followed by the SPA3102's ip each time ( eg on x-lite I
give call number 2101111111 instead of 2101111111 @ wanip: 5061 where wanip is the external ip of the router).
When x-lite is running on the computer that is on the same network with the SPA3102 everything works as expected. A
voip call is made from x-lite ( using as a proxy the wanip everytime, or even for test purposes the dyndns domain
that i set up for this reason), this call is passese PSTN line and the phone of the called party rings . At x-lite
COMES indication "call established ".
The problem occurs when I do the same procedure from x-lite installed on a computer belonging to another network (
e.g. in another building with its own internet connection , own router, own computer , etc. ) . Always using the
wanip the x-lite makes the voip call to the SPA3102, writes "call established" ( meaning it connected to SPA3102) but
never routed the call to the called party ( the SPA3102 did not forward voip calls it receives to the PSTN line ) .
Trying to find what 's wrong I've tried to disable all firewalls (soft and hard from all involved machines ) . The
behavior is the same either the computer that makes the successful calls is connected to the network directly to the
router or through the port "ethernet" on the SPA3102.
What is the difference in these two voip calls to the SPA3102 and the one " triggers " it to forward the call to
PSTN line and the other does not ?
Thanks now for any ideas you give .The audio sound problem is more than likely also associated with the overall addressing problem initially encountered. As you may know, using the sip protocol the sip signalling exchanges ip addresses to be used for both the sip signalling and the exchange of rtp sound packets. In addition there is an exchange of port numbers to be used for the exchange of rtp sound packets. The sound is exchanged by two separate streams of packets, one stream in each direction. The result is an ip address and port number for the rtp packets flowing from the SPA3102 to the softphone and a different ip address and port number for the rtp packets flowing from the softphone to the SPA3102.
In your previous posting you mentioned that you "set the minimum EXTernal rtp port at the sip tab". Changing the "EXT RTP Port Min:" is an unusual change to make and in my opinion would only be made in special circumstances. Actually, I ran some tests and I'm not sure exactly what that setting does. In my tests it didn't appear to affect the rtp port number used in a predictable manner.
The common changes to make for audio problems typically would be to setup a STUN server. A STUN server is an external server that echos back to the initial sender the external ip address and port number that the STUN server received with the message received by the server. This allows the sender (SPA3102 or softphone) to determine its external ip address and external port numbers for both the sip signalling and rtp packets.
A STUN server is commonly recommended to be setup with the following settings in the SPA3102:
PSTN Line Tab:
NAT Mapping Enable: Yes
Sip Tab:
Handle VIA received: yes
Handle VIA rport: yes
Insert VIA received: yes
Insert VIA rport: yes
Substitute VIA Addr: yes
Send Resp To Src Port: yes
STUN Enable: yes
STUN Server:
The following web page has a list of "Public STUN Servers"
http://www.voip-info.org/wiki/view/STUN
You are using CounterPath's XLite softphone. stun.counterpath.net is a STUN server on the list.
I see XLite also has a setting to use a STUN server on the "Topology" tab. -
Problem with incoming call from pstn
Hi,
we have a 2610XM router with CCME 3.2 and 4 bri
and we don't redirect incomming call from pstn on a internal IP Phone.
which command for redirect call ?
my isdn number (french) is 0156838050
and when we call this number with my mobile (number 0685284832), look this debug
debug isdn q931:
Mar 22 12:53:46.350: ISDN BR1/0 Q931: Ux_DLRelInd: DL_REL_IND received from L2
*Mar 22 12:53:46.378: ISDN BR1/0 Q931: RX <- SETUP pd = 8 callref = 0x73
Bearer Capability i = 0x8090A3
Standard = CCITT
Transer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0x89
Calling Party Number i = 0x2083, '685284832'
Plan:Unknown, Type:National
Called Party Number i = 0x81, '8050'
Plan:ISDN, Type:Unknown
Sending Complete
*Mar 22 12:53:46.382: %ISDN-6-LAYER2UP: Layer 2 for Interface BR1/0, TEI 64 changed to up
Router#
*Mar 22 12:53:46.415: ISDN BR1/0 Q931: TX -> CALL_PROC pd = 8 callref = 0xF3
Channel ID i = 0x89
*Mar 22 12:53:46.439: ISDN BR1/0 Q931: TX -> DISCONNECT pd = 8 callref = 0xF3
Cause i = 0x8081 - Unallocated/unassigned number
*Mar 22 12:53:46.527: ISDN BR1/0 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x73
Cause i = 0x87E4 - Invalid information element contents
Router#
thanks for your helpYou have to either use a transfer pattern or a translation rule.
http://www.cisco.com/en/US/products/sw/iosswrel/ps5012/products_feature_guide_chapter09186a00801812db.html -
Help!! Cant send email how change my outgoing smtp port to 587 stuck on 25
Im on OSX 10.1.4. I go to Mail, Preferences, Account, Select my email account, Select Edit, Select Account Options.
All I see is a box saying Connect to server port: and it says 143.
When I try to send mail a message says smpt port timed our port 25. I called my internet provider and they told me to change my outgoing port to 587 but I cant find where to change the 25 to 587.
If I go back to the above and change the 143 to 587 my incoming mail stops working.
Am I looking in the wrong place or did I setup my email incorrectly? I selected mac account, pop, smtp.mac.com outgoing server, mail.mac.com for incoming server...did I do something wrong. I have a mac mail email address.
Please someone help me!!
Thanks.So there's no way to send with other ports? You HAVE to use port 25?
Sure there is - talk to every mail administrator of every domain you might ever want to send mail to and have them reconfigure their mail servers to listen on some arbitrary port number that you define. Wait for them to do it (it shouldn't take them too long), and then you're done.
Oh, no, hang on a minute... none of them are going to do that, are they?
But that's what you're asking for - you're asking for them to accept mail on some non-standard port number just so you can get around Verizon's mail blocking.
There is a reason why standard port numbers (defined by IANA) exists - just so that everyone's talking on the same page (or at least in the same chapter of the same book). You can't arbitrarily pick a port number and expect it to work unless both sides of the connection know to use it. You know port 25 works for SMTP because that's the standard. You can use any port number you like for your own mail because you can configure your own mail client to use a non-standard port, but you can't convince the rest of the world to follow suit (at least not without good reason).
In this case your options are to relay your mail through Verizon's servers, upgrade to their business plan (which supports hosting your own mail server and doesn't break the user agreement), or setup another mail server somewhere else that you can relay your mail through. -
Vendor Master Bank Account Number Changes
Hi,
Where are the changes of bank account number (New and the Old one) in vendor master data Reflected , is there any Table.??
Regards,
ArchitYou can see the bank account before and after values in vendor master display or change. Call up the vendor master (XK02 or XK03), go to the Vendor: Payment transaction screen, and then select the menu path Environment -> Account Changes -> All Fields. The bank account changes will be listed under the change screen heading "Vendor Master (Bank Details)". You may need to click the button "Entries" to see the Vendor Master (Bank Details). Double-click that line and you will see the before and after values for ever bank number change.
Example:
Entry Vendor Master (Bank Details)
Date Chgd By Co Bank Number Acct/IBAN
11/30/09 ?????????? US 043318092 987654321 NEW
11/30/09 ?????????? US 043318092 123456789 OLD
Hope this helps. -
No re-determining of Header Text, when Ship-to party is changed
Hi Ravi,
Whenever ship to party has changed then header text is not re determining,
I am calling 'RV_TEXT_COPY' FM inside the include FV45PFAP_VBAP_FUELLEN_TEXTE , then its saving header text correctly,
but this include is calling whenever I click on Header Text tab, if suppose if I am changing ship to party and I am not clicking on
Header Text tab then this FM will not call , this is an issue and one more issue even in screen data is changing after
calling RV_TEXT_COPY FM but STXH table is not updating, its updating the first value when we created the order.
Can any one tell me how to solve this issue, Thanks in advance!Hi Srinivas,
Can you try out in the user exit 'EXIT_SAPMV45A_002' .
If it is not working pls let me know.
Message was edited by:
raj joe -
Converting External Ship-to-party number to Internal ship-to-party number
Hi Friends,
I am working on Ale idoc scenario in which i need to create sales order from customer purchase order. for this i need to maintain ship-to-party number in advance. Customer is providing me with list of ship to party number, but i dont want to maintain external number. I wan to maintain internal ship-to-party number and assign it to external ship-to-party number coming from idoc from customer PO.
So Please suggest how can i do this. is there some standard functionality provided by sap for this, coz i think this is standard requirement.
Thanks ,
Brijesh SoniHi Brijesh,
You can maintain the value of external ship to party number in the customer master against a system generated(internal) customer number.
This can be done in the sales view----partners tab of customer master. The field is called"partner description".
When you received an idoc,you can match the customer number in idoc to the field KNVP-KNREF and against this field pick value of KNVP-KUNNR. once the system determines the correct sold to party then ship to party will be determined automatically.
SAP has given KNREF field especially for these kind of scenarios.
Regards
Karan -
How text will be redetermined if the ship to party is changed
Hello,
The test is maintaining at ship to party level and if the ship to party is changed how the text will be redetermined here in the order the text is not redetermining. kindly give the solution for redetermination on this.
Regards,
Kishore.aHi Kishore,
Sorry, note 784371 is not released to customer anymore.
Please refer to note 548615, point 5 about the description of this standard system behavior.
You want to change the SAP standard behavior described above with a user-defined modification and trigger the text determination in dependency of other fields (for example ship-to party).
Take into account that all header texts and item texts entered manually are lost when you call you own text determination again.
If you still want to modify, use the following include for the item
data:
> FV45PFAP_VBAP_FUELLEN_TEXTE
and for the header data, use the include
> FV45KFAK_VBAK_FUELLEN_TEXTE
In both includes, the RV_TEXT_COPY function module is called. A user exit is not provided here.
Ensure that the modification is retained (using transaction SPAU) when you import a new Support Package after an upgrade.
Thanks,
Alex -
I had my number changed and now I can't use my phone. Do I need to reprogram it? And how?
You need to contact your carrier. If the carrier is GSM you need to get a new SIM from them. The easiest way is to take the phone to any of their retail stores and they can do it on the spot.
If the carrier is Verizon or Sprint in the US just call their support number. -
Home number changed without my knowledge. Want my old number back.
I have been in touch with Verizon's phone representatives ever since moving into my new apartment. Most recently, my home number changed after I cancelled digital voice service and got Verizon to put me back on my old service. The new number that Verizon has me on is not even recognized as a Verizon number! I talked to Britney the other day and was told that she would call me after getting permission to change our number back to what it was before. This current number sems like the temporary number that Joanie gave me during my FIOS installation. When I called Verizon again this morning to check the status of my inquiry I was told that they can't change my number back because it's unauthorized and that the number is not even Verizon's. My home number has been hijacked and I AM HELPLESS. Everyone says one thing and I am stuck with a number I didn't even ask for. Please help me get my old number back. This is not right.
Good afternoon Nahid,
Can you send us this information in a private message so we can look further in to this please?
~Jess -
Header text is not changing when ship to party has changed
Hello Team,
I am facing one issue when ship to party has changed in sales order the header text is not re determining automatically,
I have read some posts and found that using standard its not possible we need to write enhancement for that.
I have written below code to change the header text but facing some issues, can you please help me on to resolve this issues.
I am calling 'RV_TEXT_COPY' FM inside the include FV45PFAP_VBAP_FUELLEN_TEXTE ,
then its saving header text correctly, but this include is calling whenever I click on Header Text tab,
if suppose if I am changing ship to party and I am not clicking on Header Text tab then this FM will not call this is an issue
and one more issue is even in screen data is changing after calling RV_TEXT_COPY FM
but STXH table is not updating, its updating the first value when we created the order.
Can any one tell me how to solve this issue, Thanks in advance!Hi Mac,
I think the following user exits can help you. In the Include MV45AFZZ use the below exit points,
1) USEREXIT_MOVE_FIELD_TO_VBKD
2) USEREXIT_SAVE_DOCUMENT_PREPARE
try to write your code logic here.
Regards,
Satish -
Why has my macbook pro serial number changed after getting it repaired?
I just noticed that the serial number in the 'about this mac' information has a different serial number to what is on the back of the macbook pro, which is the same serial number on my apple care/phone . I had a lot of issues with my macbook pro it was sent to repair in july 2013 then in august 2013. Why has the serial number changed? I tried using my original serial number to use the online apple care service however it did not recgonice my serial number when I tried the new serial number it regconised it but said I did not have apple care but I do. I don't know what the apple team have done to my macbook as it requires to go in for repair again.
Was it repaired at Apple or an authorized service provider?
You need to contact the repair place/store and/or call Apple and make them aware of the problem - sooner rather than later. Make sure you give them the repair/case number so they can find the paperwork for it.
I had a logic board replaced and the tech also did not do anything - I called Apple and the tech came back to my house to take care of it. It's important because you want to make sure that your Applecare is being associated with the right serial number.
Maybe you are looking for
-
Playlist function not working correctly
I have an Ipod nano 4th generation, it works fine in every way it is supposed to except when it come to the playlist function. When ever a song is selected from a list of songs or an artist/album list containing 10+ or so songs it does not add the se
-
N73 2.0628.0.1 This model/firmware seems to be a really buggy release. There's a lot of problems people are experiencing with it. The moderators of this forum claim that Nokia staff do read and take into considaration problems reported here, although
-
Transit time in consignment fill-up
Hi, As we know that after consignment fill-up in MMBE unrestricted stock become the consignment stock,but if stock take 3-4 days to reach the customer site.So this duration( transit time) how will we show in our system. Because system immediatly show
-
Can a dataset be updated with DataAdapter.Update(dataSet)
In Oracle is it possible to use the dataAdapter Update command to insert / update multiple rows of a dataset. I have an Oracle dataAdapter with stored procedures assigned to it for the select, insert, delete, and update. But I am unable to update thr
-
Implementing Workflow without HR module
Hi everybody! I have to implement workflow in a company there is implementing SAP now. The problem is that the company will not install HR module. The question is: - How can I work with organizacional structure in the workflow? I never attended a imp