Print issues when going from develope to print

In LR5 when going from Develope to Print, I loose the picture and the print tab is greyed out. Never had this problem before, did I do something wrong

Make sure the source remains the same - check the filmstrip.
The only suggestion is to place the batch for editing and printing into a collection or (temporary) quick collection and access the images from there in both modules.

Similar Messages

Hi When going from Develop module to print module a white boarder appears on screen which also prints via my epson r3000 printer. I can get round this by exporting photo to Elements and printing from there but can i get rid of the boarder and print from l

Hi When going from Develop module to print module a white boarder appears on screen which also prints via my epson r3000 printer. I can get round this by exporting photo to Elements and printing from there but can i get rid of the boarder and print from lightroom?

In the printer driver (accessed through the Page Setup button) set the Advanced tab to borderless. Then in the right hand panel under Layout set all the margins to zero.

Problems losing quality when going from develop module to library module ?? anyone have a fix

Problems losing quality when going to library module from develop module. Sharpness and color quality decrease

This is normal. There will be a difference as you are comparing Library Previews with the image in Develop which accesses the original file, although the difference is usually slight. Real results need to be judged from exporting after selecting the output sharpening e.g. for glossy paper, if printing or screen sharpening for web images or emailing.
The idea with sharpening is to apply capture sharpening so that the image in Develop looks just sharp but not over sharp. Lightroom then uses the correct algorithm for output sharpening based upon image size and quality settings etc.

Printing issue when using Intel Macs to print wirelessly via Airport

We seem to have a problem. It has come to light since using Intel based Macs running 10.4.7 and Airport to connect wirelessly to the internet and to print to a Acculaser C1900N with intel printer driver installed. When setting up by Bonjour and then printing to the printer it fails and an exclamation mark appears on the printer icon in the Dock. Appletalk is enabled for the port, just in case you ask.
Browsing the internet works fine, but the printing side fails every time.
When we insert a Ethernet cable everything works fine.
As far as I can see its not a System Software problem related to old macs running 10.4.7, but to new Intel macs running 10.4.7. I have tried this on a Intel Mac Mini and also an Intel MacBook the results are the same.
Please has anyone got a solution as we start a new term with these new macs in about two days and printing is a integral part of school life.

I have just configured a new Airport Extreme and I have just printed sucessfully to our printer. Weird its just a Graphite Airport base Station Issue. I am not sure if the problem occours with the Snow Airport Base Station....Ill have to try that one out. I am so happy that it works you wouldnt believe it.

Lost finger print access when going from vista to xp

Starting session with finger print worked fine with vista but after tranfering to xp pro I get a message saying the computer name is incorrect. Any solution?
François

François, welcome to the forum,
did you delete the finger print profile in Vista before you installed XP?
Try clearing the finger prints in the BIOS Security menu. You will then need to create a new profile from scratch in Vista.
Hope this helps
Andy ______________________________________
Please remember to come back and mark the post that you feel solved your question as the solution, it earns the member + points
Did you find a post helpfull? You can thank the member by clicking on the star to the left awarding them Kudos Please add your type, model number and OS to your signature, it helps to help you. Forum Search Option T430 2347-G7U W8 x64, Yoga 10 HD+, Tablet 1838-2BG, T61p 6460-67G W7 x64, T43p 2668-G2G XP, T23 2647-9LG XP, plus a few more. FYI Unsolicited Personal Messages will be ignored.
Deutsche Community Comunidad en Español English Community Русскоязычное Сообщество
PepperonI blog

Time Machine Issue when going from WiFi Network to Ethernet cable

I have my WD network drive attached to my router so I can do Time Machine backups wirelessly. I updated my ancient Mac to Snow Leopard the other day for software reasons, and when I went to backup via Time Machine it said I had 4.6GB to backup. Ok. Don't understand why, but assume it has to do with the OS update. I thought it would quicker to do it through the Ethernet cable, but when I unplugged it from the router and into the Mac Time Machine said it couldn't locate it. that seemed very, very odd. I put it back into the router, and it re-appeared. The bummer is, after two days it's less than half way through the backup. I'm just going to keep it going and hope for the best, but if anybody has any thoughts on this Im all ears.

I decided to change the external drive setup to be a wireless drive over our home network, plugged into my Airport Extreme
Unfortunately, Apple does not support Time Machine backups to a drive attached to the USB port on the AirPort Extreme.
Some users seem to be able to make this work anyway, some have some success and some have no success. At best, it is not a reliable method to protect your data.
Time Machine stores backups differently depending on whether the drive is attached directly to your Mac compared to a drive that works over a network.
That's why Time Machine will make a complete new backup of your Mac when the drive is located at the AirPort Extreme. It may well be that there is not enough space on the drive to allow this.
Options...
1) keep the drive attached to your Mac. This is supported and works well.
2) Erase the drive or add a new drive and start over with a new complete backup on the drive at the AirPort Extreme
If you go for #2, I would suggest that you also develop a secondary backup plan in case things do not work out.
I've experimented 3-4 times with Time Machine backups at the AirPort Extreme and in each case.....they work fine for a few weeks or so. Then I get messages that the backups have become corrupted and I have to "repair disk". This works a few times until I cannot repair the disk and must erase the drive and start over again.
Your resullts, may of course be different.

I am trying to print from my iphone to my LEXMARK printer. When I select the select printer option when trying to set it up, it does not find my printer??? i dont know what to do at this point. Maybe it does not have the capability? it is a year old???

Hello! I am trying to print from my iphone 4 to my LEXMARK printer. When trying to select my printer in my phone it comes up and says that there are no printers available... I dont know what to do at this point. Can someone PLEASE HELP???
I also cant get my music I have purchased, to become my ringtone???????
Thank you so much,
Michael

What's the model number of your Lexmark printer?

C410a thinks I want to print photos when I want to just print paper. Won't feed regular paper.

The printer thinks I want to print photos when I just want to print papre. The Photo Printing light is on. Won't feed regular paper.

You could use the iPrint App to accomplish this. The following thread has links to show how to install and use the iPrint App for Android, iPhone, and iPod products.
http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mobile/How-to-Download-and-Use-HP-iPrint-for-Android-...
This is a link to iPrint Photo 3 for iPhone, iPod Touch, and iPad (Available through iTunes)
http://itunes.apple.com/us/app/hp-iprint-photo-3-0/id299531647?mt=8
And finally, this link shows how to use Airprint from your Apple devices via your home wireless network.
http://www.apple.com/ipad/features/airprint.html
Hope this helps
I am an HP Employee
Click the KUDOS Star to say "Thanks"
Please mark the post that solves your problem as "Accepted Solution"

JMS issues when migration from weblogic 9.2 to 10.3.5

We are facing some issues when migration from weblogic 9.2 to 10.3.5
In weblogic 9.2 :_
BMP Entity EJBs used in our project are read-only in nature using entity cache, below is the configuration details
<!DOCTYPE weblogic-ejb-jar PUBLIC "-//BEA Systems, Inc.//DTD WebLogic 6.0.0 EJB//EN" "http://www.bea.com/servers/wls600/dtd/weblogic-ejb-jar.dtd">
<weblogic-ejb-jar>
<weblogic-enterprise-bean>
<ejb-name>
Company
</ejb-name>
<entity-descriptor>
<pool>
<max-beans-in-free-pool>300</max-beans-in-free-pool>
<initial-beans-in-free-pool>150</initial-beans-in-free-pool>
</pool>
<entity-cache>
<max-beans-in-cache>3500</max-beans-in-cache>
<idle-timeout-seconds>100000</idle-timeout-seconds>
<read-timeout-seconds>0</read-timeout-seconds>
<concurrency-strategy>ReadOnly</concurrency-strategy>
</entity-cache>
Entity beans will get refreshed using the JMS messges. with in the MDB descriptor files(weblogic-ejb-jar.xml) we are using the provider URL directly and XA enabled connection factory is set to false.
migration to Weblogic 10.3.5_
With the same configurations MDB are not not getting deployed in weblogic 10 with some exception, so we removed the provider URL from weblogic-ejb-jar.xml and changed the JMS configuration to use foreign JMS and XA enable connection factory is set to true. Now when ever the JMS message is triggered Entity bean is not getting refreshed with the updated values. i.e values are stale.
Can some one look into this and provide your inputs to resolve this issue.

I think the Entity bean refresh problem appears to be unrelated to MDBs. The MDB is only responsible for getting the message to your application (which in turn interacts with Entity beans). You might want to try posting your question to an EJB newsgroup.
Tom

I can't print. When I go to file-print, nothing happens. My printer is working just fine with IE and everything else.

I can't print. When I go to file-print, nothing happens. My printer is working just fine with IE and everything else.

Try the Firefox SafeMode. <br />
''A troubleshooting mode, which disables most Add-ons.'' <br />
''(If you're not using it, switch to the Default Theme.)''
# You can open the Firefox 4/5/6/7 SafeMode by holding the '''Shft''' key when you use the Firefox desktop or Start menu shortcut.
# Or use the Help menu item, click on '''Restart with Add-ons Disabled...''' while Firefox is running. <br />
''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shft key) to open it again.''
If it is good in the Firefox SafeMode, your problem is probably caused by an extension, and you need to figure out which one. <br />
http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes

When going from a Mac-based Ai to a PC based Ai, the documents "Font" are not found on the PC version? (mostly Helvetica) where and how do I get those Fonts? And/or, can I use the Mac version of these Fonts?

When going from a Mac-based Ai to a PC based Ai, the documents "Font" are not found on the PC version? (mostly Helvetica) where and how do I get those Fonts? And/or, can I use the Mac version of these Fonts?
Thanks, Rich

In order to be cross platform you must be using the Open Type version of all fonts to cause the least disruption. Macs can read and process the Windows .ttf type format but PCs can't process Mac formatted type. Most recent versions also cannot use the older PS Type 1 fonts.

Has anyone else noticed that: "The OS X Lion v10.7.3 Update includes Safari 5.1.3 and fixes that: Resolve a Wi-Fi connection issue when waking from sleep" didn't work?

I installed OS X Lion v10.7.3 because of the following claim.
The OS X Lion v10.7.3 Update includes Safari 5.1.3 and fixes that:
Resolve a Wi-Fi connection issue when waking from sleep
It continues to be a real pain having to reconnect to the network each time I wake my MacBook Air from sleep.
Does anyone have a suggestion for the resolution to this problem?

It seems the update fixed old problems for some and caused new problems for others. Sorry to hear you're in the latter group.
Here are some things to try.
1. Go to System Preferences > Network, and click the gear icon under the network interfaces like so:
Whatever service order you have set, drag Wi-Fi either to the top (assuming it's not already there) or someplace else in the list. Click OK and then Apply. Sleep the system then wake it again to observe any changes.
2. Click Wi-Fi in the above then click Advanced. Select all the networks your computer has ever joined and delete them with the "-" button. OK then Apply again. Select your network under the AirPort icon to re-join it. Sleep and wake again to see if that did anything.
3. Try creating a new, temporary user account. Log in under that account to see if its behavior is any different.
You may have done all of these already but perhaps there is something you have not thought of. If nothing helps we may just have to wait a bit longer for Apple to release a fix.

Resolve a Wi-Fi connection issue when waking from sleep

Hi,
In the recent release for Mac OS X Lion 10.7.3 "Resolving a Wi-Fi connection issue when waking from sleep" was supposed to be resolved, not so at my end. Has anyone else encountered the same issue and if so will there be a resolve.
Thank you

Hello BGreg and thank you for your answer,
I have alreadty read about this solution, and tried it.
I downloaded the 1.2 Go file, and applied it. And repaired permissions.
Everything went fine.
Unfortunately, it didn't solve the problem.
Meaning that when iMac wakes up, it doen't join my WiFi network.
I have to do it manually.
I don't know what to do : it is very strange because I never had that problem with OS 10.7.2 !
And my network setup has never changed.
another info :
I noticed that in the network setup screen, when I want to close the little lock to restrain further modifications, it won't close. Weird !
Do you think I should call Apple Assistance ?

Printing issues when printing to Server 2008 R2 Print Server

We have a problem with netwok printing that encompasses many different areas and versions of Windows OSes so I will be posting this in a few different places.
Let me lay this out for you. We have a single Server 2008 R2 print server with 300 printers of various models. This print server has both 32 and 64-bit drivers installed for every printer. For the HP printers we are using the HP Universal Printing PCL 6
(version 61.94.3.37) and for the Ricoh printers we are using their PCL6 driver for universal printing version 3.5. All drivers run in Isolation mode and no printer gets published to AD.
We have a mix of Windows clients printing to these printers, both XP Pro and Windows 7 32 and 64-bit.
Now for the problems: The other day one Isolation host on the server went crazy, processing was hitting 100% and memory was fluctuating and growing a lot. After investigating a little that isolation host was having issues accessing the Ricoh Driver (which
was 3.4 at the time). In an attempt to resolve the issue we updated the driver to V. 3.5. This seemed to fix the isolation issues and things calmed down however this is the beginning of many other issues for the clients. Both Windows OS versions (XP and 7)
don't seem to be either downloading and installing the updated driver and/or doing so correctly. Clients are now experiencing extremely slow printing, applications such as Word, Outlook, Excel and others open slowly and it can take 2-3 minutes for print dialog
boxes to open. In all cases it seems that we have to have a tech delete the printer(s), delete the driver and then re-install the printer to make things better but for some reason, which is really unknown, this process doesn't work for every machine and on
some we can't even remove the old drivers at all without booting into SafeMode and doing it that way.
With all of that said, are there any suggestions as to why the clients aren't downloading and installing the drivers from the server correctly? How to avoid these issues when we need to upgrade the drivers on the server in the future? Most importantly right
now, are there any recommendations or scripts on how to force the deletions of the printer, driver, reset the print spoolers and then re-add the printers in a more automated fashion?
I have played with both wmic, pnputil and printuidll and am trying to put something together but without a set solution that will work consistently it becomes a lot more difficult.

We are experiencing a very similar issue.
Windows Server 2008 R2. Printers are deployed over group policy.
Clients range from Windows 7 to Windows 8. Citrix XenDesktop and XenApp environment also connects to these endpoints.
We have A wide assortment of HP printers, and Ricoh Printers.
For the ricoh's we have been historically using the PCL6 drivers for the individual device type (not universal print). Up till recently, it all was working fine, until about some time in the middle of june, when everything just seemed to go crazy.
The issue was resolved by moving off from the PCL 6 drivers and using the PCL5e driver counterparts on all of our ricoh printers.
It would crash XenDesktop applications, it would crash office applications.
The print spooler would lock up, even if the ricoh printers were not actually used, just as long as they were loaded.
Even after loading PCL5 on the servers, some of the clients would simply not download the PCL5 version of the driver from the print server. In order to resolve this, I have created the steps below. Be advised, this may possibly cause damage on your system.
We just found it worked great for us. Local printers will likely have to be manually reinstalled after this.
Directions
Stop the print spooler
Open C:\Windows\System32\Spool and delete the following
All files in SERVERS
All files in PRINTERS
All files in drivers
All files in prtprocs
Start the print spooler
Open a command prompt as administrator, and run the following command
Cscript C:\windows\system32\Printing_Admin_Scripts\en-US\prndrvr.vbs -x
This should further delete all print drivers.
Open a command prompt as a standard user (not administrator) and run the following
Gpupdate
Now wait. It takes a while, but the printers will slowly start to repopulate.
I am still not sure what is going on with the PCL6 drivers for ricoh, and why this issue is happening. I'm guessing it has something to do with the Ricoh auto update that is included in their pcl6 drivers. Maybe some sort of auto update happened recently.

Printing issue when converting an .indd file to .pdf

All,
I have two .indd files that loose color when printing after .pdf conversion. The first file looses all color and changes the text font. The second file prints correctly on the first page but not the second. The seond .indd file looses it's color all the way through.
When I view the .pdf, they both look fine. Also, If I print directly from indesign, it prints fine.
Any thoughts?
Thanks in advance!

You need to provide us with more information.
How are you creating the PDF files? Export (recommended)? Print to PostScript (strongly discouraged)? With exactly what settings?
If you examine the PDF file in Acrobat, does the document information indicate that all the fonts are embedded?
More information and we can try to begin assisting you.
- Dov

Print issues when going from develope to print

Similar Messages

Maybe you are looking for