Problem with "show interfaces transceiver"

Hi.
After we have change SUP32 with SUP720 on Cisco7600 (IOS 12.218SXF) we cannot show the optical details of our Gbeth links (for example the receive power, the temperature of the transceiver and so on).
This is the result of the command:
Router>sh int gi2/10 transceiver
Diagnostic Monitoring Data is not available.
How can I solve this problem?
Thank you very mutch.

Also to add you would be able to use the previous command only if your tranceivers are DOM capable (that is they are capable of Digital Optical Monitoring) which can be enabled globally on all capable tranceivers using "router(config)#tranceiver type all"
Here is a link for reference.
http://www.cisco.com/en/US/products/hw/routers/ps368/products_mib_quick_reference_chapter09186a00807f6bcb.html
HTH-Cheers,
Swaroop

Similar Messages

Hi! I´m having problems with showing video files in Qlab on my Macbook Air. A sound/video technician told me to "blow out" my Mac. Was told to use cmd+ r when restarting. Is this the right way?

Hi! I´m having problems with showing video files in Qlab on my Macbook Air. It started suddenly. Consulted a sound/video technician who told me to "blow out" my Mac. Was told to use cmd+r when restarting. Is this the right way to clean up my Mac? And is it likely that some kind of bug is causing problems for Qlab to show video files? I´ve already tried with a bunch of different video files and sometimes Qlab plays them and sometimes not. I need the Qlab playlist for a theatre show and only have a week until showtime so starting to really worry. Is there anyone out there who can help?

Your Mac runs maintenance in the background for you.
Command + R gives you access to restore, repair, or reformat the drive using OS X Recovery
No idea why that was suggested.
You may have a third party video player installed that's causing an incompatibility issue.
Check these folders:
/Library/Internet Plug-Ins/
/Library/Input Methods/
/Library/InputManagers/
/Library/ScriptingAdditions
~/Library/Internet Plug-Ins/
~/Library/Input Methods/
~/Library/InputManagers/
~/Library/ScriptingAdditions
The first four locations listed are in the root-level Library on your hard disk, not the user-level Library in your Home folder.The tilde (~) represents your Home folder.
To access the Home folder in OS X Lion or Mountain Lion, open the Finder, hold the Option key, and chooseGo > Library.

We have problem with showing warnings "Inline with Field"s.

We have problem with showing error messages "Inline with Field"s.
1. We have a package ERROR, that collects all errors/warnings. It has a procedure PUT, that saves errors in the variables of the package.
Package ERROR
procedure put(ptable in varchar2, pcolumn in varchar2, pcode in varchar2, pmsg in varchar2);
end;
2. We have a database table. Its values are validated by a trigger (saving business rules).
If an error occurs, then the trigger calls the procedure PUT ( to save an error message).
For example ...
CREATE TRIGGER ...
--- Rule 21
if substr(:new.ka_kood,1,1) != :new.s_kat then
error.put('TABLE1','COLUMN1', -20167, ' MESSAGE 1 !');
end if;
END;
3. I have a form of HTML DB that updates the table TABLE1
I want to show this error message with the field COLUMN1 (Inline with Field) .
I need same validations before and after updating values.
Before update - to validate same input; after update - to show errors saved in the package ERROR.
I also tried to use the global variables. For example ...
WWV_FLOW.g_validation_ids_in_error(1):= 192645056564169139;
WWV_FLOW.g_item_ids_in_error(1):= 192644674113169137 ;
WWV_FLOW.g_validation_message(1):='MESSAGE1';
And this did not help.
To rise errors in programs - is there same API ?
Or there is some other solutions ?
How can I do this in HTML DB?

Andres,
I'm not sure exactly what you are trying to do. But perhaps this will help some. If your after-submit process runs DML that causes triggers to fire, which result in error messages to be accumulated in package variables, you could create a branch on the page that would be conditional on the existence of error messages in the package variables. The branch could be back to the same page or to a more customized error page. The page you branch to would use the error messages in the package variables to determine how to format the page with the error text. The key to doing this is to run it all in the same database session. The way to do that is to use a "direct" branch, i.e., one that does not do a URL redirect. You create this type of branch with the Create Branch wizard (Branch to Page) and do not check the "Branch to page using redirect" checkbox when you see it.
Be sure to roll back any changes you do not want committed before the branch.
Using HTML DB global package variables for anything like what you described is not supported.
Scott

Problem with showing caller information on E90

I recently purchased an E90 and it appears to have a problem with showing the information of the caller (name) for those numbers that have been synchronized with Outlook 2003 or using Bluetooth from a Sony-Ericsson. The presentation of the caller information for the numbers that I have punched in manually works just fine.
Does anybody have the same problem and if so what is the solution if it is a configuration issue as it sure sounds like a software bug..
Regards,
-mats-

unfortunately the quick office solution bundled with the E90 is very much inferior to the ones found in the older communicators. you Must PAY to upgrade to a better version w/c to my mind is still inferior to the basic version found in the 9X00/i series communicators
9110,9210,i,9500,9300,i,E90 I still miss my 9300i , E71, E72 But......

Problem with showing mp3 album art in list view.

Hello.
I have litle problem with showing mp3 album artwork in list view.
In SNOW LEOPARD all work fine, and all mp3 files have album art's preview in list mode in finder.
But in LION i have only default preview mp3 icon.
Option "Show icon preview" is already on!

I have the fix!!!!
I have had the same issue ever since Lion. Its been very painful not having album art preview in finder or the play button when rollover the file for so many versions of OSX. Today I worked hard in trying to solve the problem since Applecare support hasn't helped much, all they did was tell me to bring the computer in. The other main reason I got so motivated to try and fix this is because the DJ app for Mac only reads album art from the finder even if iTunes can display the album art. The other reason that got me curious is that my friends macbook pro album art worked fine, so I cross checked with his computer until I figured out a few things that helped and ultimately fixed the issue. FINALLY!
My set up:
- I have my full iTunes library folder on my external as I have over 700GB of music.
- It includes all my database files in there, which is very important as I have many playlist settings from over 7 years of iTunes activity.
SOLUTION:
1. With every new computer I have purchased, I use to just pressed option on Mac and press iTunes to locate my folder (which I have said is located on my external drive).
2. I tried today to press option again BUT locate and selected the default library in the user/music folder of my internal drive (standard setting from Apple).
3. Miraculously, all the album art appeared in both my external drive library and also today's downloaded songs on my Macbook pro. Ofcourse with the new default location I don't have any songs or data.
4. So I tried to find a way to keep this library data on my internal drive since it can help the finder display all my files properly, yes even have the play on rollover button but as well link it back to my external drive with all my 700GB songs.
5. I then went into iTunes Preferences/Advance tab and in iTunes Media folder locationredirected the location to my external drive iTunes/ iTunes Media folder. If it asks to collate data, press NO.
6. Then I quit iTunes.
7. Next I copied the 4 files to my desktop from my external drive as I want to keep the data I have made with all my playlists etc. The four files are iTunes Library Extras.itdb ,iTunes Library Genius.itdb , iTunes Library.itl , iTunes Library.xml
8. I then went to my internal drive User/Music/Itunes/ and dragged these 4 files I copied from my external drive into here and making sure to REPLACE the four existing files already there.
9. Next open iTunes and you will find all your presettings appear with all your music linked to your external. What this does is keep the important library files on your internal drive (that somehow makes your finder files album art appear), BUT to read also all the music mp3 files located in the external drive (action from step 5)
Presto!! All your music files whether on internal drive or external all the album art has appeared.
Hope this helps!! Let me know if there are any other questions.
I am on 10.8.1 running retina macbook pro.

Problem with mac interface

Hi !
I just installed Dreamweaver CS4 on my new Macbook Pro. I used to use Dreamweaver CS4 on Windows. But, I have a problem with the interface on my macbook : when dreamweaver is running, I can see my desktop : there is no background like in a MDI application (on windows). To illustrate my problem, I took two screenshots :
on mac :
and on windows :
So, I would like to know how to have the same interface with Mac OS X than with Windows.
Thanx for your help and sorry for my english but i'm french.

Click the green zoom (+) button in the top-left corner of the window to switch between a larger and smaller window size.
Depending on the active application it either fills the entire screen or zooms to the size of the last largest size of the window that you set yourself by dragging bottom righthand corner to desired size.
Photoshop has various ways to hide the Desktop. Either by using the Application frame (which doesn't neccessarily hide the entire Desktop) or by pressing the key F. Wanted by PC users but usually not by Mac users. (I would personaly never use it as it obscures the Desktop so you cannot easily reach other applications and documents by just clicking them to call them into the front and get active).
DW doesn't have an application frame but it is easy enough to fill the entire screen with the active window, particularly if you open up a few panels and dock them to each other and use Split screen view with code on one size and design on the other, then place various bars at top and bottom. When you have organized it to your liking, save it as a Workspace (Window/Workspace Layout/New Workspace) and you have it handy for future use.
Learn how to use the windows and workspaces in an efficient way and one of these days you might get used to it...

ASR 9000 : Analogue for "show interfaces transceiver"

Hello!
Is there any convenient way to get the summary for the Rx/Tx power levels (dBm) for all DOM enabled optical interfaces on the system, like "
show interfaces transceiver" that is available on non-XR IOS ?
Thanks
WBR, Alex.

Depending on the transceiver type:
show controller dwdm optics
show controller sonet
...will show that information.

Problem with an Interface....

We have configured, and reconfigured and inteface on one of our Solaris 9, Netra 240 servers. We are having problems with bge0. It does not want to come to the state of RUNNING. ifconfig shows us:
bge0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
We have done things like unplumb, plumb ifconfig down, up, etc....

The manual page says:
RUNNING: ... for some interfaces this flag shows that the link is up.
So maybe it is a problem with the cable or the hub/switch you use.
Martin

Problem with Local Interfaces (WSAD 5)

I built an Entity Bean with Local Interface and a Remote Interface (apperently they both have the same JNDI name in WSAD)
and when I look up for the name from other Session Bean (same EJB group) and I try to cast it to the local interface there is a classCastException.............
HELP ME

Nidhi
I had the same problems as you that went away. If you have both remote and local interfaces defined, and your remote inerface can be accessed via JNDI lookup using (say) "ejb/sessionbean/stateless/HelloHome", then you can access the local intercafe using "local:ejb/ejb/sessionbean/stateless/HelloHome".
The URL http://localhost:9080/UTC/initialize?port=2809 is very useful to browse the JNDI tree. Just expand "Local EJB beans" and position your mouse over the item of interest. The JNDI lookup name will echo in the bottom (solid) frame of the browser. The only problem is that the jndilookup name will appear (mistakenly) as local:/ejb/ejb/stateless......, just get rid of the first forward-slash to make it look like local:ejb/ejb/stateless....
Hope this helps
Somnath

Problem with local interface

Hi all,
I have a problem with the local interface,
after I change the Home and Local interface I get a message when compiling saying that the bean has to implement the inherited abstract method javax.ejb.EJBLocalObject.isIdentical (EJBLOcalObject) and the mothd isPrimaryKey()...why is that, do I need to implement these methods?
Thanks,
A.

solved, wrong code

Tran.FBL1N - problem with showing correct amount regarding partial paymants

Hello,
Every day at my workplace I use transaction FBL1N which I use to see how much money I own to vendors and also to se how much is payed. However I have problem whit showing payed amounts for partial paymants (transaction F-59). For example:
I own some vendor EUR 20.000,00 and I decide to pay him EUR 15.000,00 using partial paymant option (transaction F-59) because that's amount I have at the moment on my bank account. After that, when I choose that vendor using transaction FBL1N (with enabled option Open items on current date) so I coiuld see how much it is left to pay him, amount EUR 15.000,00 is not subtracted and reprt is still showing me that I own him EUR 20.000,00 which ofcourse is not correct.
I also must note that in case I payed that vendor full amount I wouldn't have this problem and transaction FBL1N would show correct amount.
I hope someone can advise me about this and help me solve my issue.
Any help is appreciated and many thanks in advance for prompt replys.
Cheers;)
Adi
Edited by: samnovice on Jul 18, 2011 1:22 PM

thnx loky46, I understand it better now - I hva one more important question regarding this:
Is there any way I can found total amount I own to one or more vendors (_regardless_ if it is full or partial paymant or combination of both paymants)? For example:
Line 1 || VENDOR I || Eur 20.000,00 RE
Line 2 || VENDOR I || Eur 15.000,00 AB
TOTAL Eur 5.000,00
but without using this option:
you have to add the field "invoice reference" to your line layout and make a subtotal on it.
Also, is it possible for line Eur 15.000,00 to become Close item because that part is payed and for rest of amount of Eur 5.000 to be Open item because is still not payed. I assume this can't be done but on this way I could now exact total amount of money which I own to my vendor(s) and it would be a of great help to me in every-day work.
Thank you.
Edited by: samnovice on Jul 19, 2011 3:26 PM

Massive problem with audio interface

Hi there.
I recently bought a brandnew iMac 27" Haswell i7. I encountered problems with my Focusrite Scarlett 18i8 audio interface. These are buzzing, clicking and noise immediately or after 3 minutes or so. I tried everything, re-installed the driveres several times, nothing, really nothing worked.
Then I bought an RME Babyface audio interface - and guess what? It's the same problem. I also have a massive sound noise after some minutes or the recording channel in Garage Band drops completely.
What is wrong here? I already tried using a different power plug, tried all USB ports, turned off WiFi, HDD sleep mode, etc. Nothing worked.
Do you have an idea?
I appeciate your help,
Adrian.

same problem with my imac late 2012 27" 3.2ghz i5 and the motu ultrilite. up to now i have no solution for this problem. the worst i can't use them never before. since from the first day. i attempt everything. from re-install to fresh install. resetting the nvram and pram. formatting the hd and make a fresh install from the operating system. using balanced audio cables and so on...but same problem all time. even my technological knowledge and know how which i have as electrical engineer couldn't help me. first i was lucky to have apple care in those situations. after get back the imac from the service provider i sadly decide nothing has changed. and they would told me it runs all fine. in meantime i testing my ni audio dj8 over usb. it's similar with the ultralite because the buzzing, clicking and noise is not so extrem as it is on ultralite. but it's here.
the curios with my macbook pro and my old imac early 2008 it runs and works fine without problems. for next week i have fixed a new date by the service provider. but then with my intercace, monitors to simulate this error and i hope they find the reason. perhaps i can tell you some news or solutions next week. i'm relly curious about it.

Problem with showing palette component which contains swing components

hello, I have found a simple problem with jdeveloper IDE but this simple problem delays my project and it make late a big project so help me please. I want to add somes swing components to a JFrame
but when I try to show the palette component as usual I didn't find the swing components like habit.
Best Regards

duplicate
Frank

Problem with showing unit-label

Hi All,
i just have a problem with controls that have two displays (like
slider). I need the digital display with an unit-label. But when I
enable showing the label it appears two times and I have no chance to
disable one. Is there a methode that I can reach my target?
bye
Henrik

There is a way but it rather looks like a bug in LabVIEW...
The object must be a control and the VI must be in Run Mode or running:
Select the text in the unit label of the digital display and delete it.
It can generate insane object errors if you manipulate the object further,
thus it is safer just to hide the label.
Jean-Pierre Drolet
John Lum a écrit dans le message :
[email protected]..
> Henrik Skupin wrote:
>
> > i just have a problem with controls that have two displays (like
> > slider). I need the digital display with an unit-label. But when I
> > enable showing the label it appears two times and I have no chance to
> > disable one. Is there a methode that I can reach my target?
>
> Others may have a more
elegant way of getting around this, but one quick
> workaround is to edit the control to hide the unit label that you don't
> want to see.
>
> Let's say you want to hide the unit label next to the slider part of the
> control: simply select the control, do Edit >> Edit Control, move the
> offending unit label over top of the digital display, then select Move to
> Back from the Reorder menu.
>
> Regards,
> John Lum
> National Instruments
>

Show interfaces Transceiver not displaying detail on a 4500

When I run "sh interfaces transceiver" on a 4500 it fails to display any details. SFP modules fitted are GLC-LH-SMD=. When swapped into a 3750X "sh interfaces transceiver" works fine. Anyone resolved this issue ?
sh module
Chassis Type : WS-C4510R+E
Power consumed by backplane : 40 Watts
Mod Ports Card Type                              Model              Serial No.
---+-----+--------------------------------------+------------------+-----------
1    48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E
2    48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E
3    48 10/100/1000BaseT Premium POE E Series WS-X4748-RJ45V+E
4    12 1000BaseX SFP                          WS-X4712-SFP-E
5     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E
6     4 Sup 7-E 10GE (SFP+), 1000BaseX (SFP)   WS-X45-SUP7-E
7    12 1000BaseX SFP                          WS-X4712-SFP-E
M MAC addresses                    Hw Fw           Sw               Status
--+--------------------------------+---+------------+----------------+---------
1 6412.25fe.f740 to 6412.25fe.f76f 1.5                               Ok
2 1005.ca82.5540 to 1005.ca82.556f 1.5                               Ok
3 7426.ac47.eed8 to 7426.ac47.ef07 1.5                               Ok
4 a80c.0dea.e6b0 to a80c.0dea.e6bb 1.0                               Ok
5 18e7.28a1.f700 to 18e7.28a1.f703 2.1 15.0(1r)SG10 03.05.00.E       Ok
6 18e7.28a1.f704 to 18e7.28a1.f707 2.1 15.0(1r)SG10 03.05.00.E       Ok
7 a80c.0dea.de40 to a80c.0dea.de4b 1.0                               Ok
GigabitEthernet4/1 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet Port, address is a80c.0dea.e6b0 (bia a80c.0dea.e6b0)
Description: --Etherchannel to SER1-1/1--
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, link type is auto, media type is 1000BaseLH

Hi,
Here is your answer.
You should check
http://www.cisco.com/en/US/docs/interfaces_modules/transceiver_modules/compatibility/matri
x/OL_6981.html#wp142660
This tells which release we start supporting an SFP and which release we start supporting
DOM.
This shows that GLC-LH-SMD does not support DOM as of now.
We have logged the bug for the same:
https://tools.cisco.com/bugsearch/bug/CSCum99103/?reffering_site=dumpcr
HTH
Regards
Inayath
*Plz rate all the usefull posts and mark the thread as answered if this solved your query.

Problem with "show interfaces transceiver"

Similar Messages

Maybe you are looking for