Problem wrt54g3g configuration mode bridge or transparent

hi, I have a router wrt54g3g with firmare 2.0.22, I want if can configure mode bridge this router, using the card vodafone 3G, why behind router I have linux server with firewall, vpn and web to filter.
Thank you.

unfortunately this is a product limitation that u cannot bridge this router....at the most what u can do is , assign an ip address to the wrt54g3g which is in the range of the server....and disable the wireless router's dhcp..

Similar Messages

Please verify the CSS and SCA configuration for one-armed transparent mode

I have a problem to configure one-armed transparent mode. I cannot access the server with "https://9.9.9.1" even "http://9.9.9.1:80" and "http://9.9.9.1:81" operational. looks CSS cannot communicate properly with SCA.
I couldn't figure out from CCO sample configuration. please correct the attached configuraiton.
Thanks,
** connectivity ********
<client>----<router>----<CSS>---<SCA>,<Server>
- client=7.7.7.100
- router's e0/0=7.7.7.1, e0/1=8.8.8.3(connect to VLAN2 of CSS)
- SCA=11.11.11.100, connect to VLAN3 of CSS
- server=10.147.153.12 and 10.147.153.15 on the same box, connect to VLAN4 of CSS
** configuration *********
CSS11050# sh run
!Generated on 01/01/2079 00:00:47
!Active version: ap0500105
configure
!*************************** GLOBAL ***************************
acl enable
ip route 0.0.0.0 0.0.0.0 11.11.11.100 1
ip route 7.7.7.100 255.255.255.255 8.8.8.3 1
ip route 7.7.7.200 255.255.255.255 8.8.8.3 1
!************************* INTERFACE *************************
interface e2
bridge vlan 2
interface e3
bridge vlan 3
interface e4
bridge vlan 4
interface e5
bridge vlan 4
!************************** CIRCUIT **************************
circuit VLAN1
ip address 9.9.9.2 255.255.255.0
circuit VLAN2
ip address 8.8.8.2 255.255.255.0
circuit VLAN3
ip address 11.11.11.1 255.255.255.0
circuit VLAN4
ip address 10.147.153.1 255.255.255.0
!************************** SERVICE **************************
service ING_SVC_12
protocol tcp
ip address 10.147.153.12
active
service ING_SVC_15
protocol tcp
ip address 10.147.153.15
active
service ING_SVC_SCA
port 443
protocol tcp
ip address 11.11.11.100
type transparent-cache
no cache-bypass
active
service upstream
ip address 8.8.8.3
type transparent-cache
active
!*************************** OWNER ***************************
owner ING_OWNER
content cnt_443
add service ING_SVC_SCA
protocol tcp
port 443
vip address 9.9.9.1
active
content cnt_80
add service ING_SVC_12
add service ING_SVC_15
protocol tcp
port 80
url "/*"
vip address 9.9.9.1
active
content cnt_81
add service ING_SVC_12
add service ING_SVC_15
vip address 9.9.9.1
protocol tcp
port 81
url "/*" <-- If I configure url "/secure/*", not working "http://9.9.9.1:81" from client.
active
!**************************** ACL ****************************
acl 1
clause 10 permit any any destination any
apply circuit-(VLAN1)
acl 2
clause 10 permit any any destination any
apply circuit-(VLAN2)
acl 3
clause 10 permit any any destination any
apply circuit-(VLAN3)
acl 4
clause 10 permit any any destination any
apply circuit-(VLAN4)
ING_SCA# sh run
# Cisco SCA Device Configuration File
# Written: Sun Feb 6 01:12:54 2106 MST
# Inxcfg: version 4.1 build 200211151311
# Device Type: CSS-SCA
# Device Id: S/N 11aca8
# Device OS: MaxOS version 4.1.0 build 200211151311 by reading
### Mode ###
mode one-port
### Interfaces ###
interface network
auto
end
interface server
auto
end
### Device ###
ip address 11.11.11.100 netmask 255.255.255.0
hostname ING_SCA
timezone "MST7MDT"
### Password ###
password idle-timeout 15
### SNTP ###
sntp interval 86400
### Static Routes ###
ip route 0.0.0.0 0.0.0.0 11.11.11.1 metric 1
### RIP ###
no rip
### DNS ###
no ip name-server
no ip domain-name
### Telnet ###
telnet enable
### Web Management ###
web-mgmt port 80
no web-mgmt enable
### SNMP Subsystem ###
no snmp
### SSL Subsystem ###
ssl
server ING create
ip address 9.9.9.1
localport 443
remoteport 81
key default
cert default
secpolicy default
sslv2 enable
sslv3 enable
tlsv1 enable
session-cache size 20480
session-cache timeout 300
session-cache enable
no clientauth enable
clientauth verifydepth 1
clientauth error cert-other-error fail
clientauth error cert-not-provided fail
clientauth error cert-has-expired fail
clientauth error cert-not-yet-valid fail
clientauth error cert-has-invalid-ca fail
clientauth error cert-has-signature-failure fail
clientauth error cert-revoked fail
sharedcipher error failhtml
ephemeral error failhtml
no httpheader client-cert
no httpheader server-cert
no httpheader session
no httpheader pre-filter
httpheader prefix "SSL"
ephrsa
keepalive frequency 5
keepalive maxfailure 3
no keepalive enable
end
end

the problem is the routing.
You need a route for the client pointing to the SCA like this
ip route 7.7.7.100 255.255.255.255 11.11.11.100 1
This is so the reply from the server to the client goes back to the SCA first
for encryption.
Gilles.

AEBSn Configured in Bridge Mode

The AirPort Disk Utility on two separate Macs detects a shared disk attached to an AEBSn configured in bridge mode but returns an error message when trying to connect to it using an account name and password.
Could this be because a certain port or port must be forwarded from the router to the AEBSn?
I am currently forwarding ports TCP 548, 139, 445, and UDP 192. Are there any other ports that need to be forwarded so that the AEBSn is fully functional as a disk sharer while in bridge mode?

I wouldn't port forward at all to be honest. If you are port forwarding to the routers address the computers wont be able to use those ports, because they are not gettin their IP address from the base station, it's coming directly from the router, the airport base station is simply passing it on.

How to configure Message bridge

          Hi,
          I am trying to setup a JMS Message Bridge for prove of concept purpose in Weblogic
          7.0. Here is my configurations from config.xml:
          <JMSBridgeDestination
          AdapterJNDIName="eis.jms.WLSConnectionFactoryJNDIXA"
          ConnectionFactoryJNDIName="weblogic.jms.testConnectionFactory"
          ConnectionURL="t3://localhost:7001"
          DestinationJNDIName="examples.queue2" Name="LocalBridge"
          UserName="kyang" UserPassword="{3DES}2LeceOSYOaRuCvrFshnBZg=="/>
          ConnectionFactoryJNDIName="weblogic.jms.ClientConnectionFactory"
          ConnectionURL="t3://localhost:7001"
          DestinationJNDIName="examples.queue1"
          Name="MQWeblogicDestination" UserName="kyang"/>
          <JMSConnectionFactory DefaultDeliveryMode="Persistent"
          DefaultTimeToDeliver="200" DefaultTimeToLive="1000"
          JNDIName="weblogic.jms.ClientConnectionFactory"
          LoadBalancingEnabled="false" MessagesMaximum="100"
          Name="ClientConnectionFactory" OverrunPolicy="KeepNew"
          ServerAffinityEnabled="false" Targets="examplesServer"/>
          <JMSConnectionFactory DefaultDeliveryMode="Non-Persistent"
          DefaultTimeToDeliver="200" DefaultTimeToLive="1000"
          FlowControlEnabled="false"
          JNDIName="weblogic.jms.testConnectionFactory"
          Name="testConnectionFactory" OverrunPolicy="KeepNew" Targets="examplesServer"/>
          <MessagingBridge Name="MyMessaging Bridge" Selector="*"
          SourceDestination="LocalBridge"
          TargetDestination="MQWeblogicDestination" Targets="examplesServer"/>
          I used a test client get InitialContext with url:"t3://localhost:7001" and send
          the message to "examples.queue2" which is "MyJMSQueue".
          From the monitor screen I found the message was put on "MyJMSQueue" but the message
          was nerver delieveried to the "examples.queue1".
          From the log, I got following message:
          <Jun 20, 2002 10:05:53 AM CDT> <Info> <MessagingBridge> <200012> <Bridge "MyMess
          aging Bridge" suceesfully found the two adapters configured for it.>
          Do you have any suggestions?
          Thanks a lot!


Don't worry about the log messages about
          "comp/env/wls-connector-resref".
          It is not a problem for the Messaging Bridge feature.
          The real problem is that you have an invalid selector for the
          MessagingBridge. A bridge selector has the same syntax as a JMS message
          selector. As you can see from the JMS specification, a message selector
          syntax is based on a subset of the SQL92 conditional expression syntax.
          I would suggest you try the bridge feature without any selection first
          and add the selector later.
          Dongbo
          Kenny Yang wrote:
          >
          > Mr.Xiao,
          > Thanks! Things are getting better after I made changes according to your suggestion.
          > Now the status is showing: Forwarding Messages. But I still have following exceptions
          > from the logging window:
          >
          > <Jun 20, 2002 1:38:50 PM CDT> <Info> <MessagingBridge> <200020> <Bridge "MyMessa
          > ging Bridge" is stopped.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200033> <Bridge "MyMessa
          > ging Bridge" is getting the connections to the two adapters.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190011> <Unable to locate cont
          > ext: java:/comp/env/wls-connector-resref>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190010> <Unable to determine R
          > esource Principal for Container Managed Security Context.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190011> <Unable to locate cont
          > ext: java:/comp/env/wls-connector-resref>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190010> <Unable to determine R
          > esource Principal for Container Managed Security Context.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190035> <There was/were 1 phys
          > ical connection(s) created with the following Meta Data: Product name of EIS ins
          > tance: Java Messaging Service Product version of EIS instance: 1.0.2 Maximum num
          > ber of connections supported from different processes: 0 User name for connectio
          > n: kyang>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190011> <Unable to locate cont
          > ext: java:/comp/env/wls-connector-resref>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <Connector> <190010> <Unable to determine R
          > esource Principal for Container Managed Security Context.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200031> <Bridge "MyMessa
          > ging Bridge" is configured to allow degradation of its quality of service in cas
          > es where the configured quality of service is not reachable.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200030> <Bridge "MyMessa
          > ging Bridge" is configured to work in "Atmost-once" mode and it is actually work
          > ing in "Atmost_once" mode.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200028> <Bridge "MyMessa
          > ging Bridge" starts transferring messages.>
          > <Jun 20, 2002 1:38:55 PM CDT> <Info> <MessagingBridge> <200026> <Bridge "MyMessa
          > ging Bridge" encountered some problems to one of its adapters or underlying syst
          > ems. It stopped transferring messages and will try to reconnect to the adapters
          > shortly. (Exception caught was java.lang.reflect.UndeclaredThrowableException)
          > java.lang.reflect.UndeclaredThrowableException: java.lang.reflect.InvocationTarg
          > etException: javax.resource.ResourceException: Error creating asynchronous consu
          > mer or setting message lisenter
          > at weblogic.jms.adapter.JMSBaseConnection.throwResourceException(JMSBase
          > Connection.java:1086)
          > at weblogic.jms.adapter.JMSBaseConnection.setMessageListenerInternal(JMS
          > BaseConnection.java:984)
          > at weblogic.jms.adapter.JMSBaseConnection.setMessageListener(JMSBaseConn
          > ection.java:892)
          > at weblogic.jms.adapter.JMSConnectionHandle.setMessageListener(JMSConnec
          > tionHandle.java:121)
          > at java.lang.reflect.Method.invoke(Native Method)
          > at weblogic.connector.common.internal.ConnectionWrapper.invoke(Connectio
          > nWrapper.java:92)
          > at $Proxy131.setMessageListener(Unknown Source)
          > at weblogic.jms.bridge.internal.MessagingBridge.beginForwarding(Messagin
          > gBridge.java:842)
          > at weblogic.jms.bridge.internal.MessagingBridge.execute(MessagingBridge.
          > java:922)
          > at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:152)
          > at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:133)
          > >
          >
          > where can I get the context:"comp/env/wls-connector-resref"?

Problem with Append mode in File Receiver

Hello,
I am facing some problem with Append Mode in File Receiver.
In channel config, i have given :
Construction Mode : Append
File Type : Text
Message Protocol : File Content Conversion
The size of the file which i am trying to send is about 9.5MB.
I got this error,
"Recovering from loss of connection to database; message
loaded into queue by recover job: System Job (Failover Recovery)".
So, it would seem that there was a loss of connnection to the database
while the file was being written.
Note - XI successfully recovered from the connection loss and
successfully wrote the file, however since the communication channel
was set to append, it appended to the partial file that was written
before the database connection loss. This is not correct. The file
should have been overwritten after the recovery even though the communication
channel was configured to append.
Can anyone help me on this regard.
Thanks,
Soorya.

Hi Venkat,
I would suggest u to split the file in to chunks if u face any problem in processing at a time in append mode and also
Memory Requirements are must 4 processing huge files:
Q: Which memory requirements does the File Adapter have? Is there a restriction on the maximum file size it can process?
A: The maximum file size that can be processed by the File Adapter depends on a number of factors:
o The most important one is the size of the Java heap, which is shared among all messages processed at a certain point in time. In order to be able to process larger messages without an out of memory error (OOM), it is recommended to increase the size of the available Java heap and/or to reduce the concurrency in the system so that fewer messages are processed in parallel.
o Another factor negatively influencing the maximum message size in releases up to and including XI 3.0 SP 13 is an enabled charcter set (encoding) conversion if the message type is set to "Text".
o Using the transport protocol "File Transfer Protocol (FTP)" also uses more memory for processing than the transport protocol "File System (NFS)" (up to and including XI 3.0 SP 13).
o If the Message Protocol "File Content Conversion" is used in a File Sender channel, consider that not only the size of the input file affects the File Adapter's memory usage, but even more the size of the XML resulting from the conversion, which is usually a few factors larger than the original plain text file.
To reduce the memory consumption in this scenario, consider configuring the setting "Maximum Recordsets per Message" for the sender channel. This will cause the input file to be split into multiple smaller mesages.
Plz do refer the following links:
U may plan the availability of ur communication channel using "Planning Availability Times" feature
http://help.sap.com/saphelp_nw04/helpdata/en/45/06bd029da31122e10000000a11466f/frameset.htm
/people/sravya.talanki2/blog/2005/11/29/night-mare-processing-huge-files-in-sap-xi
hi check the below links for reference
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/10748ef7-b2f0-2910-7cb8-c81e7f284af5
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/7086f109-aaa7-2a10-0cb5-f69bd2affd2b
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/2498bf90-0201-0010-4884-83568752a857
https://www.sdn.sap.com/irj/sdn/go/portal/prtroot/docs/library/uuid/cc1ec146-0a01-0010-90a9-b1df1d2f346f
Regards,
Vinod.

Extremes (Access Point Mode, Bridged) Constantly Going Offline

I have multiple Extremes (all standalone access point mode, bridged with static IPs) randomly going offline. Each Extreme is connected directly to a main switch. Status lights always remain green however I cannot ping the devices, they do not show up in the Airport Utility and they cease to be accessible/visible via WIFI. Plus, when this happens, I often can STILL connect to devices (e.g. printers) that are plugged into the LAN ports of the "offline" Extremes.
They appear to drop randomly, i.e. not under any particularly heavy load or anything. When I feel them physically, they don't feel unusually warm or anything.
Thoughts? I have already done a hard reset and reconfig on one of the problem devices.

Hello Julesomar,
It sounds like your Airport Extreme is having intermitent connectivity issues. You have already done what I would have started with by resetting the device. I recommend next troubleshooting for sources of interference with the following article:
Wi-Fi and Bluetooth: Potential sources of wireless interference
http://support.apple.com/kb/ht1365
Thank you for using Apple Support Communities.
All the very best,
Sterling

HT1937 i have just downloaded a new version of Iphone software on my iphone 3 . but i'm facing problem in configuring it . also tried to configure it with itunes but it always says that there's no sim card in your phone and previously i was using same sim

i have just downloaded a new version of Iphone software on my iphone 3 . but i'm facing problem in configuring it . also tried to configure it with itunes but it always says that there's no sim card in your phone and previously i was using same sim without any problem . need solution . kindly help .

Hello ashharuddin,
Thank you for using Apple Support Communities.
For more information, take a look at:
iPhone: Troubleshooting No SIM
http://support.apple.com/kb/ts4148
Toggle Airplane mode On and Off.
Try turning iPhone off and then on again.
Check for a carrier settings update. Tap Settings > General > About. If an update is available, a prompt will appear.
Remove the SIM Card and verify that it is a valid, carrier-manufactured SIM. Also verify that it is not damaged, worn, or modified. Then reinsert it.
Restore the iPhone.
Have a nice day,
Mario

Can users directly access aeronets configured as Bridges?

Here is our scenario, We have two Aironet 1400's facing each other to extend our LAN btw two buildings
One is configured as root bridge the other is non root bridge. I see an option in the GUI to
configure as an Access Point. My question is- Does the fact that I have the aironets configured
as bridges prevent unauthorized clients from accessing the bridges and thus our network?
Are these bridges considered Access Points that a laptop can attach too?

Hi Richard,
If you do not want 802.11 clients on the bridge, leave the default Role in the Radio network value to bridge only mode. This allows only other bridges to communicate with the device.
From this excellent Q&A doc;
http://www.cisco.com/en/US/products/hw/wireless/ps441/products_qanda_item09186a0080094d01.shtml#ethernet
Hope this helps!
Rob

Problem in configuring Portal 3.0

Hi,
I am using Oracle 9iAS Rel 1.0.2.2.2a with 9i database Rel 9.0.1 on windows2k server. I am able to login with "sys" in normal mode by adding
"O7_dictionary_Accessibility = True" to the parameter file. But the problem is that the portal needs "shared_pool_size = 31457280", whereas, I have given "shared_pool_size = 33554432" which is heigher than the required size.
I have tried even with Oracle 9iAS Rel 1.0.2.2.0 but i still get the same error.
Please help me to come out of this problem and configure the portal.
Can mail to [email protected]
Thanks,
Ravindra

must apply patch for bug 2014354, base bug: 1874284, on this platform.

How to configure 8192 bridge domain default limit shows 2048

Hello,
How can i scale up bridge-domain from 2048 to 8192.
As per the link (http://www.cisco.com/c/en/us/td/docs/routers/asr9000/software/asr9k_r4-1/lxvpn/configuration/guide/lesc41/lesc41p2mps.html) ASR9000 series routers can scale up to 8192 bridge-domains.
However my ASR9k shows the l2vpn capability to be only around 2048. How can i configure 8192 bridge-domain
RP/0/RSP0/CPU0:ci-asr9k#show l2vpn capability
Tue Feb 10 14:11:36.797 EST
Capability mode: mixed-mode
L2vpn all-capable: N
System capability:
VPLS Max MAC addresses: 32000
VPLS Max bridge-domains: 2048
VPLS Max attachment circuits: 32768
VPLS Max pseudowires: 32768
RSI bit size: 13
Per-AC drop counters supported: Y
VPLS Preferred path allowed: Y
VPLS Preferred path fallback enable allowed: Y
VPLS Preferred path fallback disable allowed: Y
MAC withdrawal allowed: Y
Max attachment circuits per bridge-domain: 16384
VPLS Max virtual forwarding interfaces: 2048
VPLS Max virtual forwarding interfaces per bridge-domain: 1
VPLS Max pseudowires per bridge-domain: 512
VPLS Max pseudowires per virtual forwarding interface: 512
VPWS PW redundancy supported: Y
VPLS Access PW supported: Y
Bundle AC supported: Y
Security config supported: Y
DHCP snooping supported: Y
VPLS Static MAC filter supported: Y
VPLS MAC configs on bridge port supported: Y
VPLS Flooding config on bridge port supported: Y
Flood unknown unicast disable supported: Y
IGMP snooping supported: Y
MMRP flood optimization supported: Y
MMRP flood optimization max multicast address entries: 8192
MMRP flood optimization max PW participants: 262144
VPLS MAC Aging Default Timer Value: 300
VPLS MAC Aging Min Timer Value: 300
VPLS MAC Aging Max Timer Value: 30000
VPWS Max attachment circuits: 32768
VPWS Max pseudowires: 32768
VPWS Preferred path fallback enable allowed: Y
VPWS Preferred path fallback disable allowed: Y
-Ramdas

Are there any LC scale profiles configured in the admin mode? If so, that would reduce L2 resources. If you don't need the L3 profile, remove it and reboot the router to gain back 8k bridge domains.
Regards,
/A

After iPad ios 5 upgrade, itunes "interrupted while restoring" restore gets error -50. iPad starts in 'configure' mode - can I configure as 'New iPad' and then restore?

After iPad ios 5 upgrade on Win7 64bit pc (x386 iTunes), iTunes gave me error "iTunes was interrupted while restoring, restore again now?" I try to restore but iTunes immediately gives error -50. Apple website says -50 is a timeout, but I have tried all fixes: changed usb ports, new cable, reset iPad, restart pc, remove sim... no good.
iPad starts in 'configure' mode, but won't restore from any of the several iTunes backups I have. Ready to giveup on 'restore'! iPad is sync'ed in iTunes, connects and syncs ok, so I don't want to lose that info.
Can someone from Apple advise - can I 'configure' as 'New iPad' and then restore or sync to recover my Apps and data etc? OR if I 'Restore' from iTunes 'Summary' tab, will I still be able to Sync to restore the iPad Apps and data?
I'm seeing a lot of frustrated Apple users online, hoping that a fix for this problem will help a few of us!! An iOS upgrade should not cause this much pain and wasted effort.

You might already have tried all of these, but just in case:
1. Make sure you have the latest version of iTunes.
2. If you're on a Windows PC, consider uninstalling iTunes and Quicktime, restarting the PC, then reinstalling. This sometimes fixes oddities.
3. Make sure you have no firewall or anti-virus running/active.
4. Try different USB cable; if you're using a cable via a hub, try connecting without the hub. On desktop PCs, the direct (non-internal-hub) USB sockets are usually at the back.
5. If yoiu haven't already done so, download the iOS5 update via the direct links I posted above
6. If using Update doesn't work, use Restore. Option-click (Mac) or Shift-Click (Windows) the Restore button in itunes.
7. Before you to the Restore, right-lick the entry for your device in iTunes and choose Backup from the drop-down menu. You may need this backup later.
If you're srtuck in recovery mode:
- There are some tips here for Windows users
http://thehowto.wikidot.com/ipad-stuck-recovery-mode
- If your device is stuck in Recovery mode, you can try putting it into DFU mode, from which iTunes should be able to Restore, as above. Details here:
http://www.tipb.com/2010/12/02/tip-put-iphone-ipad-dfu-mode/
- This link points to a utility that can help (Windows and Mac)
http://runningblind.com/post/2800674985/ipad-stuck-in-recovery-mode-for-no-reaso n
I hope something here helps

Cisco E2500 (Linksys) configured as Bridge works then fails

I've set up the E2500 at one end of the house with a wire connection from my router at the other end of the house. It's plugged into a LAN port. After a system reset and configuration of SSID, password, etc., I set it to Bridge mode.   It works for awhile and gets DHCP from the main router (192.168.1.254) then 5-10 minutes later the device reverts to using 192.168.1.1 as both router IP and DNS IP and stops working. At that point, I can no longer access setup info using 192.168.1.1 as a URL.
What is causing this? IP conflict?
There's not much to configure once Bridge mode is selected so I can't figure what's failing.

Windows IP Configuration
   Host Name . . . . . . . . . . . . : Home-PC
   Primary Dns Suffix . . . . . . . :
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
   DNS Suffix Search List. . . . . . : attlocal.net
Ethernet adapter Local Area Connection 4:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : TeamViewer VPN Adapter
   Physical Address. . . . . . . . . : 00-FF-3A-62-88-96
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . : attlocal.net
   Description . . . . . . . . . . . : Realtek PCIe GBE Family Controller
   Physical Address. . . . . . . . . : 54-04-A6-22-AA-9E
   DHCP Enabled. . . . . . . . . . . : Yes
   Autoconfiguration Enabled . . . . : Yes
   IPv4 Address. . . . . . . . . . . : 192.168.1.94(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Lease Obtained. . . . . . . . . . : Wednesday, April 29, 2015 3:24:53 PM
   Lease Expires . . . . . . . . . . : Saturday, May 02, 2015 3:24:53 AM
   Default Gateway . . . . . . . . . : 192.168.1.254
   DHCP Server . . . . . . . . . . . : 192.168.1.254
   DNS Servers . . . . . . . . . . . : 8.8.8.8
                                       8.8.4.4
   NetBIOS over Tcpip. . . . . . . . : Enabled

Problem in configuring Terms of Payment

Hello Friends,
I'm facing a problem during configuration of payment terms in which i give 15% discount to the customer if paid within 15 days & also the credit period is 15 days for net payment. When i try to configure the same i get an error message FC114 - Enter periods in ascending order, since the cash discount period & the credit period are the same.
Payment Terms - Within 15 days 15% discount, Within 15 days due net
Request your assistance.
Regards,
Padmanabhan

Hi Padmanabhan,
your requirement is not clear, for both the options are on the same day, there should be some difference in days for a discount and net payments in any business, try to collect correct requirement from your client. It may be further 15 days from the due date for discount, then it becomes 30 days.
How do you offer both options to your customers, in any business i did not heard such terms,
correct me if i am wrong.
Bye
Venkat Cheedalla.

Problem with configuration of wifi newtork- dhcp

hi.
i've got a small problem with configuration of wi-fi network.
i use dhcp network.
there are some errors about network during boot up (but its to fast for my to write it down)
after log-in i have to setup network access by typing
iwconfig eth2 essid SpeedTouchBCE72F
and then i heve to run this command
dhclient
and after that i've got an access to internet
this is my rc.file
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="pl_PL.UTF-8"
HARDWARECLOCK="localtime"
TIMEZONE="Europe/London"
KEYMAP="-u pl2"
CONSOLEFONT="lat2-16.psfu.gz"
USECOLOR="yes"
LC_ALL="pl_PL.UTF-8"
LESSCHARSET="UTF-8"
# HARDWARE
# Scan hardware and load required modules at bootup
MOD_AUTOLOAD="yes"
# Module Blacklist - modules in this list will never be loaded by udev
MOD_BLACKLIST=()
# Modules to load at boot-up (in this order)
# - prefix a module with a ! to blacklist it
MODULES=()
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
HOSTNAME="linugrat"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available
# interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# Note: to use DHCP, set your interface to be "dhcp" (eth0="dhcp")
lo="lo 127.0.0.1"
eth2="dhcp"
INTERFACES=(lo eth2)
ROUTES=(!gateway)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network-profiles
#NET_PROFILES=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng ipw3945d network netfs crond)
# End of file
szymon

Hi Mariano
I think you need to <b>restart your portal Engine</b> after making correct settings.
Also please refer to the link below to get a better insight:-
http://help.sap.com/saphelp_nw04s/helpdata/en/0b/719a425ffac46ae10000000a155106/frameset.htm
Regards
Navneet

Problem in configuring sunoneportal

Hi all,
I am installing Sun java portal server 7 with JES 5 on windows xp and having problems in configuring it when i want to login to portal server console login then the authentication fails .I checked the log file I found this two exceptions
#|2007-10-25T15:08:00.303+0200|WARNING|SJS Portal Server|debug.com.sun.portal.admin.server|ThreadID=13; ClassName=com.sun.portal.admin.server.PASMechanism; MethodName=parse; |PSAD_CSPAS0000 : Exception stack trace for the message above
com.sun.identity.authentication.spi.AuthLoginException: Failed to create new Authentication Context: Naming Service is not available.
     at com.sun.identity.authentication.AuthContext.login(AuthContext.java:516)
     at com.sun.identity.authentication.AuthContext.login(AuthContext.java:356)
     at com.sun.portal.admin.server.PASMechanism.parse(PASMechanism.java:169)
     at com.sun.cacao.agent.auth.CacaoCallbackHandler.handle(CacaoCallbackHandler.java:98)
     at com.sun.jdmk.security.sasl.plain.PlainServer.verifyAuthenticationCredentials(PlainServer.java:186)
     at com.sun.jdmk.security.sasl.plain.PlainServer.evaluateResponse(PlainServer.java:118)
     at com.sun.jmx.remote.opt.security.SASLServerHandler.consumeMessage(SASLServerHandler.java:124)
     at com.sun.jmx.remote.opt.security.AdminServer.connectionOpen(AdminServer.java:176)
     at com.sun.jmx.remote.generic.ServerSynchroMessageConnectionImpl.connect(ServerSynchroMessageConnectionImpl.java:51)
     at javax.management.remote.generic.GenericConnectorServer$ClientCreation.run(GenericConnectorServer.java:383)
     at com.sun.jmx.remote.opt.util.ThreadService$ThreadServiceJob.run(ThreadService.java:208)
     at com.sun.jmx.remote.opt.util.JobExecutor.run(JobExecutor.java:59)
java.lang.NoClassDefFoundError: Could not initialize class com.iplanet.services.naming.service.NamingService
     com.iplanet.services.naming.WebtopNaming.updateNamingTable(WebtopNaming.java:690)
     com.iplanet.services.naming.WebtopNaming.getNamingProfile(WebtopNaming.java:603)
     com.iplanet.services.naming.WebtopNaming.getServerID(WebtopNaming.java:405)
     com.iplanet.services.naming.WebtopNaming.getServerID(WebtopNaming.java:381)
     com.iplanet.services.naming.WebtopNaming.getAMServerID(WebtopNaming.java:159)
     com.iplanet.dpro.session.Session.<clinit>(Session.java:317)
     com.iplanet.sso.providers.dpro.SSOProviderImpl.createSSOToken(SSOProviderImpl.java:100)
     com.iplanet.sso.SSOTokenManager.createSSOToken(SSOTokenManager.java:242)
     com.iplanet.am.console.base.ConsoleServletBase.checkAuthentication(ConsoleServletBase.java:352)
     com.iplanet.am.console.base.ConsoleServletBase.validateSSOToken(ConsoleServletBase.java:238)
     com.iplanet.am.console.base.ConsoleServletBase.onBeforeRequest(ConsoleServletBase.java:188)
     com.iplanet.jato.ApplicationServletBase.fireBeforeRequestEvent(ApplicationServletBase.java:1105)
     com.iplanet.jato.ApplicationServletBase.processRequest(ApplicationServletBase.java:591)
     com.iplanet.jato.ApplicationServletBase.doGet(ApplicationServletBase.java:459)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:747)
     javax.servlet.http.HttpServlet.service(HttpServlet.java:860)could any one help ? thanks

The easiest way to get Portal to run on Windows is by using the pre-configured zip file distribution. You simply unzip the file and run a quick setup script and then the entire portal with three samples is up and running. The JES installer is not needed.

Problem wrt54g3g configuration mode bridge or transparent

Similar Messages

Maybe you are looking for