Problems dual booting Windows Vista with Oracle Enterprise Linux 4

I tried dual booting my sony laptop which came pre installed with windows Vista,After a successful installation,windows Vista boots fine,but Oracle enterprise linux just stops booting at this point " Starting Udev...................................................(OK)
Initializing hardware....Storage network"
It's posibly a hardware compatibility problem but I dont know why I get stuck at this point.Can anyone help please?

hi,
r u getting this error while installing oel or after installation?
which version of oel u r installing?
u may get this error probably due to hard disk (usually sata) compatility with linux.
--Regards
Xaheer

Similar Messages

Dual Booting Windows 7 with pre-installed Windows 8 Laptop

Hi All,
Just after a bit of advice, my girlfriend has recently got a new laptop and unfortunately she doesn't like it, despite me loving Windows 8.1.
She would like to try Windows 8 but is going back to Uni soon so would like Windows 7 as a back-up dual booted.
I've shrunk the partition and created a simple partition for Windows 7 but really unsure about Installing Windows 7 on a Windows 8 Laptop, it's an ASUS X550CA-XX417H. I've checked power shell with SecureBootUEFI and result is True.
What would be the best way to dual boot?
Cheers,
Ben

Hi Ben,
Here is a detailed guide for your reference:
How to Dual Boot Windows 8 with Windows 7
http://www.pagestart.com/win8dbwin701181301.html
This response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you. Microsoft does not control these sites and has not tested any software or information found on
these sites; therefore, Microsoft cannot make any representations regarding the quality, safety, or suitability of any software or information found there.
Hope this could be helpful.
Kate Li
TechNet Community Support

[SOLVED] dual booting windows 7 with btrfs on grub-bios -- core.img

I am trying to install arch in a dual boot configuration with an existing windows 7 partition. I have everything from the beginner's guide done but the bootloader. When I run grub-install it tells me that core.img is too big.
Some googling tells me that this is relatively common with btrfs, and it seems the only work around is to switch to gpt mode and use a grub bios partition. But the info I've seen indicates that I need to use MBR mode to dual boot windows.
Is it safe to do this with windows? Is there another workaround? Or will I have to settle for ext4?
Last edited by jorenko (2013-06-09 03:53:24)

Well there's your problem, your first partition starts at sector 63. With recent versions of windows and fdisk (and every other partitioning tool I can think of off the top of my head) things now align themselves correctly. Also because there is now GPT, the first partition typically starts later as the GPT partition table will typically sit between the MBR and the first partition.
On a MBR partitioned system, grub2 will actually use the first 446 bytes like normal, but will then also use the space that is empty where GPT would sit. This is why when you have a GPT partitioned system, it will require you to create a 1-2MB grub boot partition, as it needs somewhere else to put its bloat. GPT actually still uses the MBR section, but simply creates one large partition covering the whole disk. This is so that tools that are not GPT aware will not think that they have a whole free disk to use as they please.
For comparison, here is whe I get from fdisk:
# fdisk -l /dev/sda
sudo fdisk -l /dev/sda
[sudo] password for curtisshima:
WARNING: fdisk GPT support is currently new, and therefore in an experimental phase. Use at your own discretion.
Disk /dev/sda: 250.1 GB, 250059350016 bytes, 488397168 sectors
Units = sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk label type: gpt
# Start End Size Type Name
1 2048 2099199 1G EFI System EFI System
2 2099200 252166798 119.2G Linux filesyste arch-btrfs-1
3 252168192 488397134 112.7G Linux filesyste arch-btrfs-3
Note that I do use GPT. But that is not the point here. What I am trying to show is where my first partition starts. This is also where fdisk will start partitions these days. This is to ensure compatibility with 4k advanced format disks.
If you are not dead set on Grub2, you could try using syslinux. I really like it much better, though if you are booting more than one Linux, you need to either employ chainloading to various partition boot records, or have a shared /boot. Having a windows partition doens't really matter, as you are simply chainloading to that funky reserved partition anyway.
The other option is to use grub-legacy, which can still be found in the AUR. I actually liked the orginal Grub, as it provided a nice feature set, but was still configurable by hand and it actually fit into the MBR.

T440P Dual Boot Windows 8 with Centos 7

So I have a T440p with Windows 8 installed. I have been trying to dual boot Centos 7 and also have attempted Centos 6.5. I have been using a bottable USB to perform the installation for both Centos 7 and 6.5.
When I try the Centos 7 install, I set the boot priority to USB first on startup, and it goes to a screen that lists options to install, verify Centos 7 or troubleshoot. Upon selecting any of these options, everytime I get the error message:
"alua: not attached"
When attempting the Centos 6.5 Live DVD install, I try to boot into the Live mode, but it freezes in the process each time.
I have heard about there being issues dual booting Windows 8 in UEFI mode with another Linux Distrobution.
Has anyone here sucessfully dual-booted Centos or any other Linux Distrobution on a T440P?
Any help/advice would be much appreciated.
Thanks

It's been many, many years since I don't do dual boot anymore. Don't find the reason to do it, either. Different kinds of virtualization should be enough. Anyway...
dfw1417 wrote:
It took over 2 days to figure out how to adjust the bios to get my win 7 pro DVD to boot and install dual boot on this GREAT MACHINE!!
ENJOY! This is the BEST machine I ever had!
WHICH machine?
Cheers.
If I helped you, please give me some kudos! ^^

Advice on dual-booting Windows 7 with UEFI motherboard

I'm going to build a desktop PC tomorrow, having finally purchased all the parts for it. I'll be installing Arch as my main OS, and Windows for gaming. However I'm not really versed in UEFI and its uses, advantages/disadvantages; since my laptop just uses BIOS.
My plan is to have 3 drives: 32GB SSD for the / partition, 1TB HDD for /home, and 500GB for Windows 7 x64 Ultimate.
Being unused to UEFI I was thinking about trying to just run everything in BIOS/Legacy mode, but that doesn't seem very sensible to me, especially since I have the hardware so I might as well use it.
So, reading the wiki and forums have led me to conclude that having a 1GB EFI System Partition on the SSD should be sufficient, and use gummiboot for my bootloader.
Other reading about setting up dual boots suggests to me that installing Windows 7 on its own HDD with MBR partitioning and Arch on a separate (set of) drive(s) with GPT partitioning will be sufficient. The reason being that if the BIOS is set up to boot sda, which has GRUB as its bootloader, using GRUB I can choose to boot into Windows despite it being on a separate hard drive.
My questions are (and it occurs to me that I am in the most part just looking to have my ideas confirmed):
1. Have I gotten this all completely wrong?
2. If I'm correct, can the above system of using GRUB on one drive to boot up an OS on another drive be applied to UEFI?
3. Has anybody tried/succeeded/failed to dual-boot in this fashion before me, and if so what did they do?
Thanks one and all! Hopefully I've made myself clear enough here

billodwyer wrote:Being unused to UEFI I was thinking about trying to just run everything in BIOS/Legacy mode, but that doesn't seem very sensible to me, especially since I have the hardware so I might as well use it.
Using BIOS/CSM/legacy mode can work fine; however, it will probably slow down the boot process by a few seconds, and it will close off some possible future (and even current) advantages, as EFI support in Linux is improved.
So, reading the wiki and forums have led me to conclude that having a 1GB EFI System Partition on the SSD should be sufficient, and use gummiboot for my bootloader.
A 1GB ESP is more than sufficient. In terms of space requirements, 100-500MB is enough, depending on how you use the ESP; but various bugs and default settings make me recommend 550MiB as a good size. Bigger is OK, but wastes some disk space.
A bigger issue is that the ESP won't really benefit much from being on your SSD, since it's read once at boot time. The biggest advantage to putting the ESP on the SSD in your setup is that if you use gummiboot, you'll also have to put the Linux kernel and initrd file on the ESP, so having them on an SSD will speed up the boot process by about 1-5 seconds. Overall, I'd probably put the ESP on one of the spinning disks.
One more comment: gummiboot can launch boot loaders from its own partition but not from other partitions. This can work fine if you plan things carefully, but with three disks and two OSes, you must be absolutely positive that Windows uses the ESP on which gummiboot is installed. I'm not an expert on Windows installation, so I can't offer any specific pointers or caveats on this. If you need something with more flexibility, both rEFInd and GRUB can redirect the boot process to other partitions or physical disks. rEFInd can also redirect from an EFI-mode boot to a BIOS/CSM/legacy-mode boot. (See below.) Overall, rEFInd's flexibility on this score is a plus compared to gummiboot; but gummiboot is covered in the Arch wiki's beginner's guide, which is a plus. You'll have to pick which advantage you prefer. (Note that I'm rEFInd's maintainer, so I'm not unbiased.)
Other reading about setting up dual boots suggests to me that installing Windows 7 on its own HDD with MBR partitioning and Arch on a separate (set of) drive(s) with GPT partitioning will be sufficient. The reason being that if the BIOS is set up to boot sda, which has GRUB as its bootloader, using GRUB I can choose to boot into Windows despite it being on a separate hard drive.
This is an unworkable idea, at least as stated and if you want to do an EFI-mode boot. Windows ties the partition table type to the boot mode: Windows boots from MBR disks only in BIOS mode, and from GPT disks only in EFI mode. Thus, using MBR for the Windows disk will require a BIOS/CSM/legacy-mode installation of Windows. Furthermore, neither gummiboot nor GRUB can redirect from EFI mode to BIOS mode (or vice-versa), so if you do it this way, you'll be forcing yourself to boot Linux in BIOS mode, to switch between BIOS-mode and EFI-mode boots at the firmware level (which isn't always easily controlled), or to use rEFInd to redirect from an EFI-mode boot to a BIOS-mode Windows boot.
Overall, you're best off either using GPT for all your disks and booting all your OSes in EFI mode or using MBR for Windows (and perhaps all your disks) and using BIOS-mode booting for all your OSes.
Under EFI, the boot process is controlled by settings in the NVRAM, which you can adjust with "efibootmgr" in Linux, "bcfg" in an EFI shell, or "bcdedit" in Windows. (The Arch wiki covers the basics at least efibootmgr and bcfg.) In a typical dual-boot setup, you tell the computer to launch your preferred boot manager (EFI-mode GRUB, rEFInd, or gummiboot, most commonly), which then controls the boot process. You set up boot loaders for all your OSes on one or more ESPs. (Note: A boot manager lets you choose which boot loader to run, and a boot loader loads the kernel into memory. GRUB is both a boot manager and a boot loader. rEFInd and gummiboot are both boot managers. The EFI stub loader, ELILO, and the EFI version of SYSLINUX are all boot loaders but not boot managers. Most EFIs include their own boot manager, but it's usually primitive and awkward to use. It's also not standardized, so my computer's built-in boot manager is likely to be different from yours. Thus, I recommend against relying on the built-in boot manager for anything but launching your preferred boot manager.) Thus, the lowest-common-denominator type of setup is to put your preferred boot manager, the Windows boot loader, and a Linux boot loader (which could mean your Linux kernel) on a single ESP. If you want to use multiple ESPs or otherwise split things up, you cannot use gummiboot as the boot manager, since it can't redirect the boot process from one partition to another. (Many EFIs can do this with their own built-in boot managers, but this isn't guaranteed, and it's usually more awkward than using rEFInd or GRUB.)
I know this can be a lot to absorb. The official rules aren't really all that complex, but different EFIs interpret the rules differently, and the different capabilities of the various boot managers and boot loaders creates a lot of subtle implications for how you set everything up.
1. Have I gotten this all completely wrong?
Significant parts of it, I'm afraid; see above. You're working under BIOS assumptions, which don't apply to EFI.
2. If I'm correct, can the above system of using GRUB on one drive to boot up an OS on another drive be applied to UEFI?
GRUB can do this, but gummiboot can't. You set one of those (or something else, like rEFInd) as your primary boot manager. Using both GRUB and gummiboot adds unnecessary complexity, IMHO. OTOH, setting up multiple boot managers or boot loaders is possible, and can give you a fallback in case one fails. For instance, there's a known bug that affects 3.7 and later kernels, mostly on Lenovo computers, that causes the EFI stub loader to fail sometimes. Thus, if you use rEFInd, gummiboot, or the EFI's own boot manager to launch the kernel via the EFI stub loader, having GRUB, ELILO, or SYSLINUX set up as a fallback can provide helpful insurance in case a kernel upgrade causes your normal boot process to fail.
3. Has anybody tried/succeeded/failed to dual-boot in this fashion before me, and if so what did they do?
Many people dual-boot Windows and Linux under EFI. There are a huge number of possible solutions. My own Windows/Linux dual-boot system uses:
rEFInd
rEFInd's EFI filesystem drivers
Linux kernels on Linux-native /boot partitions (two partitions, one for each of the two distributions installed on that computer)
The Windows boot loader on the ESP
This works well for me, but it wouldn't work with gummiboot instead of rEFInd, since gummiboot can't redirect the boot process to another partition. (gummiboot also can't automatically load filesystem drivers.) Arch Linux users who use gummiboot often mount the ESP at /boot, which enables gummiboot to easily launch the Linux kernel. Doing this with multiple Linux distributions would be awkward, though, since you'd end up with two distributions' kernels in the same directory.

Can't dual boot windows 7 with windows 8 on Thinkpad edge S430

I am desperately trying to install windows 7 from USB.
I need it to dual boot with windows 8.
I obtained a windows 7 iso from MSDNAA: (en_windows_7_professional_with_sp1_x64_dvd_u_676939.iso)
I made a bootable UEFI USB with rufus on a Sandisk U3 Cruzer (8GB)
Now in BIOS I disabled secure boot but I can't select my USB, I can select it, press enter, the screen flickers but jumps back to the first entry in the boot list.
The USB is displayed without "UEFI:" in front.
Selecting "legacy" in boot mode works but I can't install windows 7, the setup shows al the partitions but says: "Windows cannot be installed to this disk. The selected disk is not of the GPT partition style".
That's it, I just can't install windows 7...
Solved!
Go to Solution.

Ok got it working:
a U3 Cruzer is NOT a good bootable USB!
csm should be enabled in BIOS.
secure boot should be DISABLED in BIOS.
(My problem was csm and the bad USB)

Dual boot Windows 7 (64) and Arch Linux (64) problems

Hello:
I am new to Arch Linux and just finished installing the 64bit on my laptop. It had a prebuilt Windows 7 (64) installed which I kept but split the hdd from 160Gb to 80Gb and 80Gb. I installed Arch there and set 4 partitions, all of them as Logical - a 64 MB ext2 /boot partition; a 512 MB swap partition; a 15 GB root partition; and the rest as my /home partition. My partitions look like this:
Disk Drive: /dev/sda
Size: 160041885696 bytes, 160.0 GB
Heads: 255 Sectors per Track: 63 Cylinders: 19457
Name Flags Part Type FS Type [Label] Size (MB)
sda1 Primary Unknown (27) 12889.02
sda2 Boot Primary NTFS 106.93
sda3 Primary NTFS [] 73915.11*
sda5 Logical Linux ext2 65.81*
sda6 Logical Linux 509.97*
sda7 Logical Linux ext2 15002.92*
sda8 Logical Linux ext2 57549.55*
The install was succesful(this was running from the core install cd) and I installed GRUB to my /boot but when I restarted it loaded Windows 7. I have used Knoppix USB disc to boot and see my Arch Linux install files and edited the /boot/gur/menu.lst file.
In Windows I installed EasyBCD 1.7.2 and tried to get NeoGrub bootloader working as a dual boot. I tried getting rid of the boot flag for Windows with cfdisk and setting it to my (Logical) sda5. That did not work. So far the only way I have booted into my Arch Linux install has been by going to the Live CD, choosing "Boot from Existing Linux Install" and editing the command files there.
root (hd0,4)
kernel /vmlinuz26 root=/dev/sda3 ro
initrd /kernel26.img
My goal is to get a dual boot working for Windows 7 and Arch Linux 64 and continue installing the Xorg and KDE to Arch. I just don't know what the problem is here. I don't mind reinstalling Arch if something went wrong, but I would like to keep my Windows running in order and add Arch on.
Any help would be greatly appreciated.

I ran the LiveCD and chose "Install to MBR hd0". I ended up with this:
setup hd(0,1)
Checking if "/boot/grub/stage1" exists.....yes
Checking if "/boot/grub/iso9660_stage1_5" exists.....yes
Running "embed /boot/grub/iso9660_stage1_5 (hd0,1)".....failed(this is not fatal)
Running "embed /boot/grub/iso9660_stage1_5 (hd16)".....failed(this is not fatal)
Running "install /boot/grub/stage1 d (hd0,1) /boot/grub/stage2 p (hd0,1) boot/grub/menu.lst".....failed
Error 31: File is not sector aligned
My entry for Windows into the menu.lst looks like this:
# (0) Arch Linux x64
title Arch Linux x64
root (hd0,4)
kernel /vmlinuz26 root=/dev/disk/by-uuid/3841273c-d91e-41d6-9dbf-716a15d03a01 ro
initrd /kernel26.img
# (1) Arch Linux x64
title Arch Linux x64 Fallback
root (hd0,4)
kernel /vmlinuz26 root=/dev/disk/by-uuid/3841273c-d91e-41d6-9dbf-716a15d03a01 ro
initrd /kernel26-fallback.img
# (2) Windows 7
title Windows 7
rootnoverify (hd0,0)
makeactive
chainloader +1

Problem dual booting Windows 8 and windows 7 G480

I bought new laptop g480 and it comes with windows 8 single language and I want to dual boot it with windows 7 Ultimate. So I create one partition 50 Gig using Minitool Partition Wizard, after that I boot into USB device ( I've bootable Windows 7 USB and already disable secure boot in BIOS). The process went fine until it ask me where to install the windows, so I choose the partition 50 Gig I created before but I get this message "Windows cannot be installed to this disk of the GPT partition style". Help me guys how to solve this problem, I've searched solution for this but non of them seems working for me. Step by step will be good for me. I hope to get quick reply for this because I've this problem since 2 days ago and never get solution .
Thank you.
Solved!
Go to Solution.

Hi @CharlyAR
I tried your solution before I posted the message here but it didn't work but then I give it try again and I manage to install the Windows 7 ultimate. Now my pc dual boot with windows 7 and windows 8 (windows 8 is the main OS).
p.s. This is important guys, if u want to make windows 7 bootable USB by following the tutorial on youtube it wont work if you pc/laptops is pure GPT (UEFI) because most of them using MBR to make the tutorial thats why it look easy and works for them, it's almost same but there's "add-on" with GPT mode. You have to make the windows 7 bootable USB in GPT (UEFI) mode or it wont let you install. I couldn't find tutorial for this GPT mode on youtube.
All I do is search my old DVD-RW and erase it and I follow the tutorial here, same what @CharlyAR told me
http://www.youtube.com/watch?v=z7rRsQGew28

Dual Boot Windows 7 with Ubuntu

Hello! I am Vasanth.
my laptop is HP Pavilion g6 2016tx. it runs on Windows 7 Home Basic!
My college have given me a project on Linux OS and i want to Dual boot that with Win 7.
I dont have other computer to do my project.
so, Is it safe to partition my local disk c and install Ubuntu in my lappy?
do i hava to do sme thing for this.
Please Guide me. Looking forward for a reply.
thanks in advance!

vasanthnanduri wrote:
Hello! I am Vasanth.
my laptop is HP Pavilion g6 2016tx. it runs on Windows 7 Home Basic!
My college have given me a project on Linux OS and i want to Dual boot that with Win 7.
I dont have other computer to do my project.
so, Is it safe to partition my local disk c and install Ubuntu in my lappy?
do i hava to do sme thing for this.
Please Guide me. Looking forward for a reply.
thanks in advance!
Hi,
Yes it is. You may try this: https://wiki.ubuntu.com/WubiGuide
I prefer to repartition entire disk and then install a fresh Windows 7. It takes two partitions. Then create an extended one plus a small partition at the end for swap but it's not necessary as computers today have enough RAM and swap is basically pointless.
Dv6-7000 /Full HD/Core i5-3360M/GF 650M/Corsair 8GB/Intel 7260AC/Samsung Pro 256GB
Testing - HP 15-p000
HP Touchpad provided by HP
Currently on Debian Wheeze
*Please, help other users with the same issue by marking your solved topics as "Accept as Solution"*

Dual boot (Windows Vista + Archlinux)

First hello people, this is my first post.I need some guidance here. I installed Archlinux in my laptop ( DELL XPS M1330) from a USB stick memory everything went smooth until i got to the grub part. I did it as the wiki mention I installed the grub at the /boot partition :
/dev/sda1 * Windows Vista NTFS ( Marked as boot)
/dev/sda2 Win Backups NTFS
/dev/sda3 /boot ext2
/dev/sda5 /SWAP ----
/dev/sda6 / ext3
I uncomment the windows part of the menu.lst . At boot Archlinux boots normally but when I want to boot linux , it blinks and takes me back to grub . Then with cfdisk I toggled to boot at /boot and unmarjed the original (Windows Vista ) and the same result then I toggled both /boot and Windows vista and the same result . What do you think I should do ?? I'm lost !! Thanks people.

aragorncito wrote:At boot Archlinux boots normally but when I want to boot linux , it blinks and takes me back to grub .
Do you mean when you try to boot Windows it blinks back to grub, or when you want to boot linux it brings you back to grub?
Did you check your menu.lst to make sure that you adjusted what partitions it is looking for (remember, grub starts counting at 0, so sda1 will be (hd0,0) in grub)

How can I dual-boot Windows 7 with pre-Installed Windows 8.1

Hi, I have a Toshiba Satellite C55-B5362 with pre-installed Windows 8.1.
Make DualBoot Windows 7 and Windows 8.1 (both 64 bit), so, I don't know how to do this. If I set BIOS to CMOS and Install Windows 7 disabling Secureboot, I will lost all the pre-installed Windows 8.1 and the OEM licence.
and other question... if the upper is not possible. Okay. I will delete Windows 8.1 and Install Windows 7 permanently until Windows 10 is released, but.... If I have Windows 7 with CMOS BIOS and SecureBoot disabled, then supposing that I could have problems with Windows 7, and I want to upgrade to Windows 8.1 again, and supposing that I have a Recovery Partition backed in a USB drive, what can I do for re-install OEM Windows 8.1 and the licence.
Thanks.
Solved!
Go to Solution.

As I said above...
..you will need to install essentially all of them to make that laptop work as designed.
..install the TVAP before any other Toshiba utility.
-Jerry

Dual Boot Windows 7 with preinstalled Windows 8 on GPT-formatted hard disk and UEFI BIOS.

Question for Jordon Wees,
Hi,
You wrote: I can successfully install both operating
systems in UEFI mode, with Windows 7 on the first partition and Windows 8 on
the second partition. <o:p></o:p>
But I couldn´t!<o:p></o:p>
Could you please provide me how to install Windows 7
64 bit on a PC that already has Windows 8 64 bit preinstalled?<o:p></o:p>
I have also a GPT-formatted hard disk with UEFI BIOS
but I get the error message that windows can´t install Windows 7 on the disk
because it is a GPT-formatted hard disk.<o:p></o:p>
I don´t understand this because it is a GPT-formatted
hard disk with Windows 8 on it!<o:p></o:p>
I can´t change the hard disk to MBR format because I
will lose Widows 8 and all other partitions.<o:p></o:p>
In the BIOS for the storage dives Boot´ option I
selected the: only UEFI, I could also select the option ´first UEFI´ but it doesn´t
change the failure of installing Windows 7.<o:p></o:p>
Thanks, Sia

If I am reading your issue correctly. Windows 8 came pre-installed on a computer with a hard disk setup as a GPT with UEFI configured.
If this is the case then the outcome you are experiencing is correct.
Windows 7 does not inherently have the ability to install into a GPT disk from the base installation.
The Windows 7 DVD is designed to install using BIOS mode.
Also note that Windows 7 x86 does not support UEFI mode.
These two articles below may help you.
http://technet.microsoft.com/en-us/library/dd744321(WS.10).aspx
http://blogs.technet.com/b/askcore/archive/2011/05/31/installing-windows-7-on-uefi-based-computer.aspx
Thanks
Sean
MCTS: Windows 7
MCITP: Windows 7 Enterprise Administration
MCSA: Windows 7

How does the Develop Applications on windows working with Oracle on Linux

Hi list
I'd built a machine.
OS: RedHat 9.0
Database: Oracle 9iR2
Every service works fine for me (dbstart|dbshut|dbca|oemapp xxx)
But Now my girl friend needs to use Windows
XP, so I can't use this machine with a monitor.
And I would like to use TOAD or DBQwikedit to connect the
Oracle Database Server. But they always failed by the error messages such as `DLL_UNAVAILABLE'. I was not familiar with Windows XP or 2000.
Thanks in advanced!
--Armani Liao

Hi Armani,
maybe u need to re-install the program.
btw how did you solve the linking error of ins_oemagent.mk on the installation of the oracle 9i R2 on RH 9?
-andi

RPM missing in Oracle Enterprise Linux 5.4

The RPM oracle-firewire-module-2.6.xxxx is missing in Oracle Enterprise Linux.
I have two servers:
1) One runs Redhat EL kernel 2.6.9-11.xxx. I can see my firewire drive from Redhat.
fdisk -l ===> show firewire partitions.
rpm -qa ===> show RPM oracle-firewire-module-2.6.xxxx
2) One runs OEL kernel 2.6.18-164.el5PAE (lateset download from Oracle Store). I cannot see my firewire drive from OEL.
fdisk -l ===> nada
rpm -qa ===> nada
This is very disappointing. Oracle Linux is missing Oracle's own RPMs. I did several installs and made sure I picked everything available in DVD. Further, I searched install media and did not see any firewire RPMs in the DVD. OSS (oss.oracle.com) does not provide RPMs for versions later then Oracle Enterprise Linux 4. I was demoing RAC with Oracle Enterprise Linux 4. Then I upgraded to Oracle Enterprise Linux 5 and now I am screwed. I will have to go to Redhat EL5.

Actually this process has been simplified by quite a bit in 5.4. The original poster has probably already figured this out, but in case someone else looks, the thing to do is comment out the firewire-ohci entry in /etc/modprobe.d/blaclist-firewire and then restart. I was still not able to see anything, so I found the rescan-scsi-bus.sh script and then I could finally see my device. The latest version of the script I found was 1.35. I mention that because I found a few different ones.
My trouble at the moment is that the device /dev/sdx can only be seen on one server at a time. If I shut down one machine, & then rescan, then I can see it on the other. I can use nfs and export it, but that is not quite what I wanted.

Dell Precision M6600 laptop Certification for Oracle Enterprise Linux 5.5

Dear Experts,
Please share the certification for Dell Precision M6600 laptop with Oracle Enterprise Linux 5.5 (x86 64 bit) Operating System.
Please give it a high priority as this is a business critical requirement.
Thanks & Regards
Chetan Vithlani

867508 wrote:
Please give it a high priority as this is a business critical requirement.
867508
     Newbie
Handle:      867508
Status Level:      Newbie
Registered:      Jun 21, 2011
Total Posts:      1
Total Questions:      1 (1 unresolved)
Moderator Comment
To reinforce what was mentioned in the first response...
There is no "urgent" in these forums and your statement that everyone must jump to your request just because you say so is rude.
You have been a viewer of these user-to-user OTN forums for more than a year. That is far long enough to know better.
For the future, whenever you have a critical business need for information, you will need to use your support credentials and log a SR ro Oracle Technical Support. Be prepared each time to prove to them that such a need exists.

Problems dual booting Windows Vista with Oracle Enterprise Linux 4

Similar Messages

Maybe you are looking for