Problems setting up Airport Extreme w/o wireless card

I just got an airport base station to host a dialup connection for an OSX 10.4.2 G4 Quicksilver 867 and a PC running win2k. No wireless cards on any of the machines.
I cant get it setup. using the Setup assistant, it see's the station and gives it a number. Then I get a messege saying "There was an error connecting to the air port base station you selected." regardless if I choose new setup or edit setup. If I click OK, at the bottom of the main screen it says "Reading Configuration". I let it run like that for an hour. I tried the admin tool as well, "cant read configuration" error there.
I think I likely need a wireless card to even access it.
But when I access the airport setup assistant, it says something about I'd "only be able to configure the LAN only. but it ddint help. rebooted computer and airport. i have it connected via ethernet.

Thanks Duane! I was in static IP mode and had to switch to dhcp and then yeah, i used the admin utility. thanks for everything. dialup to earthlink worked and I set my router and all systems to DHCP.
is there a difference between the 10.x.x.x IP range and the normal 192.168.1.x Ip pool? I always used the later in the past but noticed a choice in the airport admin tool.

Similar Messages

HELP! Problem with setting up Airport Extreme in "extend wireless network mode"!

So I am trying to put my AirPort extreme in extend a wireless network mode. So I factory reset it, plugged it in, and went into Airport Utility to set it up. So it finds the device, and I set it up to extend the network. It does everything, and it gets set up. But there is an error message that says it was unable to extend the wireless network. Then 1 minute later, the Airport Extreme drops out, and the Airport Utility says device not found. I tried this multiple times, and it keeps happening. What should I do?

Unfortunately, the AirPort Extreme will not be able to wirelessly extend a Netgear product. That feature will only work if you are connecting the AirPort Extreme to another Apple router.
If you want the AirPort Exteme to provide more wireless coverage, you will need to plan to connect it to the Netgear router using a permanent, wired Ethernet cable connection.

Problems setting up Airport Extreme with RCA Modem

Can't seem to get wireless working with my Airport Extreme. I have an RCA Modem (DHG535-2) through Comcast. I can get internet through Airport via ethernet, but only when the AEBS is in "Bridge" mode. I have tried unplugging, rebooting, etc., but nothing. The most common error message I'm getting is that the AEBS doesn't have a valid IP address. I'm pretty sure I should be selecting Use DHCP, but I'm not sure whether I need Share IP address, Distribute or Bridge. Also, when I connect via the ethernet, it looks like the IP address changes every time I reset the connection. Is this normal? I don't believe I have a unique IP address or else Comcast probably would have told me.
I've also tried resetting the AEBS to no avail. The modem does not have a typical reset button, but rather one called "REBOOT EMTA", which has kept me away from pushing it, ha! I'm very disappointed with the AEBS. I hardly ever have issues with Apple products. Any help would be greatly appreciated! Would hate to have to replace the Airport with my old blue Linksys router.

I'm not at home so I can't look at my own setup, but for my cable modem, I also have an RCA Modem (about two years old). I have it set to just get the IP address automatically, which it did the first time I plug in an Airport Express to it. I just upgraded to a Time Capsule, and all I had to do was turn the modem off and on, and it automatically works.
I would start over and try again.
Also, to reset my Airport Express to factory settings, it has a small button on the bottom that I just hit (with a tip of a pen) for five seconds and it resets. I would think the AEBS has something like that?
Good luck!

Airport Extreme Base Station Wireless Woes

Hi,
I just bought this dual band Airport Extreme Base Station on 3/10/2010. After I setup the Airport, I have difficulties connecting my iphone 3GS to the base station. My iphone 3GS is able to see the wireless network but not able to join it. Only my macbook pro is able to connect wirelessly. My windows PC and iphone 3GS could not.
I wonder whats could be the problem?
Some logs from the base station:
Oct 06 23:00:04 Severity:5 Associated with station <mac address of iphone 3GS>
Oct 06 23:00:04 Severity:5 Installed unicast CCMP key for supplicant <mac address of iphone 3GS>
Oct 06 23:00:04 Severity:5 Disassociated with station <mac address of iphone 3GS>
Oct 06 23:00:04 Severity:5 Rotated TKIP group key.
Setting of Airport Extreme Base Station:
Wireless Security: WPA/WPA2
Wireless Channel: Auto
Creating a new network
Things I have tried:
1) Changing the wireless channel
2) Removing the wireless security
Thanks

I think I manage to find the problem on why my airport extreme keep on dropping connection.
This is my connection.
Cable Modem -> Airport Extreme -> Aztech Gigabit Homeplug 1-> Aztech Gigabit Homeplug 2 -> Dlink DIR-825.
When I plug out the conenction from Airport Extreme to Aztech Gigabit Homeplug 1, I am able to connect to the wireless using iPhone 3GS. Once I plug back the connection and do a refresh the iPhone 3GS wifi connection, I am not able to connect the wireless.
Hmm, anyone faces the same problem?

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro. What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
NOTE: If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did. He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse.
THIS IS WHAT YOU WILL NEED TO DO:
First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up. If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it. Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
Wireless Security will be -> WPA/WPA2 personal or just WPA2
Enter the Wireless Password you want
Verify the Wireless Password (enter it again)
After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow. Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green. If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green. Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
I have a Linksys WRT320N I used for the initial Charter setup.
I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
Hasn't caused any issues so far but one thing I did notice.
On the Linksys there were 3 DNS servers listed.
The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
I tried everything above, but light on modem still flashes yellow.
I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

How to set up 6th Generation AirPort Extreme to cable modem as a wireless router and then connect my 3rd Generation Time Capsule to AirPort Extreme as a wireless extender?

What is the best way to set up my 6th Generation AirPort Extreme (A1521) to my cable modem as a wireless router and then connect my 3rd Generation Time Capsule (A1355) to my AirPort Extreme as a wireless extender? I live in a small 1 story house and I currently have the Airport Extreme connected to my cable modem in the living room and the Time Capsule plugged into the wall in my bedroom. I am able to wirelessly connect to the internet using the AirPort Extreme as my router and I can also do wireless back ups to my Time Capsule. My problem is that my connection seems to be really slow! My 1TB Time Capsule back up is only half way complete and it has been 3 days! My computer has been backing up all day and night for almost 72 hours and its still not even 75% complete. I have backed up to this Time Capsule in the past and it never took this long. I am thinking that when I set up my AirPort Extreme and Time Capsule using AirPort Utility I must have set it up incorrectly or something.
How do I set up my Airport Extreme and Time Capsule for the fastest possible internet speed and back up speed?
Thank you,

AirPort Utility 5.6 works with AirPort Extreme 802.11g base stations.
It works with N version airports.
It will also show details of the AC model but cannot be used for the setup.. mostly.
I purposely got the new 6th Gen Airport Extreme so my internet connection would be a lot faster!
Your network will be much faster when you have AC client directly connected to the AE. Older client will go no faster.. but what is worse.. extend wireless is mixing new and old wireless standards.. guess what one wins.. OLD.. So when you extend wireless.. you have no improvement whatsoever. This whole post is about extending wireless.. so you cannot extend to older equipment and do any better.. maybe slightly better signal although from your comments that isn't happening either.
I would rather not have to use an ethernet at all with the TC and I don't know EOP adapters are!
If you do not use ethernet then you are going to be forced to accept slow speed.
EOP (ethernet over power). Also called homeplug in the US.
http://en.wikipedia.org/wiki/HomePlug
Provides a method of networking over power cabling that already exists in your house.
So what your saying is for the fastest internet speed and back up speed possible I should keep my Airport Extreme plugged into my Modem and keep my TC set up as a wireless extender? Then when I want to do back ups I should plug an ethernet cable from my TC to my MacBook Pro?
To spell this out.
A wireless link to an extended device will go very slowly.. if it is not direct.
So lets say you have a laptop sitting in the lounge.. Your connection goes.. Laptop- - - - - AE- - - - -TC.
That means two wireless links.. wireless has this nasty half duplex and single channel nature.. it can send or receive (Tx or Rx) but not at the same time.
Ethernet by contrast does both at once. It is full duplex.
Wireless can talk to one client at a time.. so if there are multiple items using wireless lets say 4 devices.. then your computer gets a 25% time slice. Since wireless cannot handle multiple simultaneous connections.
Ethernet by contrast can connect multiple computers to multiple destinations at the same time.. all transmitting and receiving at full speed.
When you put all this together.. there are a couple of rules for fast connection.
1. Use ethernet at all times. Where you cannot use ethernet use anything but wireless.. eg EOP (homeplug) at least to try and get rid of wireless.
2. Where you must use wireless use it sparingly and make sure it is never more than one hop.. ie never have an extend wireless (repeater is more usual term). Repeater will cause instant slowdown of 50% and maybe up to 75% just because it is so inefficient.
3. Fastest wireless is 5ghz but it has very short range.. you need to be up close and personal to get it working.
Apple routers however unless you do manual setup I suggest are set to connect to best signal strength not best speed. It will therefore use 2.4ghz at 25% less speed than 5ghz because it is 1db better signal.. this madness means you need to setup manually for the best setup.

Can I set up Airport Extreme for wireless printiing over Uverse network?

I previously had DSL, and used my Airport Extreme as my wireless router. It was in my home office, so my printer was directly plugged into the Base Station. I recently switched to ATT Uverse, which came with its own wireless router. The new router is in another room, next to the TV. My question is this: Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network? Thanks.

Welcome to the discussions, Patrick!
Can I set up my old AEBS to function as a wireless printing outpost, like an Airport Express, that would be connected to my office printer but accessed through the ATT network?
In theory, yes. In practice, this is one of those things that you won't know until you try. Since the AEBS will have to "join" your ATT wireless network, the biggest question will be whether or not you can find a matching security setting on the AEBS for the ATT wireless network.
Are you able to get into the setup pages on the ATT router to see exactly what type of security is being used? Ideally, it will be WPA2 Personal, but different manufacturers use different names and flavors for the same thing, so it's rarely as easy as one might hope when you try to get devices from two manufacturers to talk to each other over wireless.

Why can't I set up my AirPort Extreme as a wireless jumper from my Cable internet router ?

Why can't I set up my AirPort Extreme as a wireless jumper from my Cable internet router ?

If it "joined" my network is it extending the coverage of my wifi network ?
Please review my previous answer in the post above......
But, the Express does not "extend" or "repeat" the wireless signal when it joins a network. In other words, wireless devices cannot connect to the AirPort Express the way that you have it set up.
If so can my Airport Extreme be set up to "join" my network and also extend the coverage of my network ?
Again, please review my previous answer in the first reply above......
The AirPort Extreme does not have this type of capability.
If you have both an AirPort Extreme and an AirPort Express.....my suggestion....again, found above in a previous post.....
It takes a minimum of two Apple routers to extend a signal using wireless.
You could do this by connecting the AirPort Extreme to your cable router using a permanently installed Ethernet cable and then configuring the AirPort Extreme to "create a wireless network".
Then add an AirPort Express in a location where it can pick up a strong wireless signal from the AirPort Extreme and configure the Express to "extend a wireless network".
You would not use the wireless on your cable router at all, unless you wanted to reserve that network for guests or something similar.

After setting up airport extreme to my existing wireless network after restart unable to conect even the light is green is telling me need to manage network im usin airport utility in pc

I try to set up my airport extreme thru my existing wifi network using airport utility 5.6 on pc after i was done said that after restarting unable to located extreme to check in my manage networks Ican se green light on extreme but can not find in network to manually add on. Any help woul be appreciated!

If nothing works, try a factory reset: disconnect the Extreme from power, press the reset button, plug in power while still pressing the reset button, release reset button after 5 seconds or so.
This method usually helps me with problems with my Airport Extreme and Express (this happens seldom by the way). The only disadvantage is that you have to set it up again completely.

How do you set up airport extreme with a windstream all in one modem with the wireless router built in

I have a wireless network that I want to extend so there will be wifi coverage all over the whole house. I want to use the airport extreme to do so. so far all i can get to work is the airport making another network via a eithernet cable that is pluged into one of the ports on the windstream wireless router/moden (all in one you plug the phone line into this and it has the wireless built in) and the other end is in the WAN port of the airport. I guess the real question is do I need to change any settings on the windstream wireless router/modem to do so. Every time I select all the options to extend a network wirelessly I keep getting errors.

The Airport Extreme can not wirelessly extend a 3rd party router, it can only extend another Apple router. If you can somehow keep the two connected via ethernet, you can setup a roaming network. A roaming network is essentially "extending" your network by using an ethernet cable to bridge the two routers.

Set up Airport Extreme with 2 Airport Express connected by CAT5??

I recently bought an Airport Extreme base station and an Airport Express. My plan was to use to Airtunes with my AV receiver in my basement. Unfortunately, because the distance between these two areas is long (and separated by two floors) I'm not able to get a strong enough signal with the Airport Express to use Airtunes. I bought another Airport Express to put on the middle floor of our house but the signal in the basement was still not strong enough even with this addition.
I do have a way of connecting the middle floor of our house with the basement area by a CAT5 ethernet cable. My plan now is to connect the two Airport Express modules by their ethernet ports with this cable. The Airport Express on the middle floor connects with the Airport Extreme base station wirelessly without any problems. My question is what is the proper setup for the 2nd Airport Express connected by ethernet in my basement.
Airport Tech support said this could be done. They recommended setting up a new wireless network with the 2nd Airport Express by "fooling" into thinking it was connected directly to the router but using the same network name with a different wireless channel as my Airport Extreme base station. This setup actually works for several hours but then the Airport Express module that is connected to the Airport Extreme blinks amber. Interestingly the 2nd Airport Express with usually remain with the green light on.
Does anyone have any suggestions for the best way to set this up regarding network configuration with the Airport Utility?
Thanks

wmskaggs, Welcome to the discussion area!
They recommended setting up a new wireless network with the 2nd Airport Express by "fooling" into thinking it was connected directly to the router but using the same network name with a different wireless channel as my Airport Extreme base station.
That will work with as long as the AirPort Express (AX) is connected via Ethernet. The only other setting you need to make is to configure it to act as a bridge (not sharing a single IP address).
If this one looses connection, then something is wrong with the AX or the Ethernet connection (cable and/or connectors).

Best configuration for Time Capsule & Airport Extreme running one wireless network?

We just moved to a house that does not have Ethernet pre-wired so I've had to re-setup the wireless network in a different configuration and it seems we're experiencing deteriorated wireless signal for devices like laptops. It will work perfectly fine (and fast! wheee!!!) but then it will slow to a crawl and mostly timeout. before I reset everything and start from scratch, I'd like some help. As an FYI, when connected via Ethernet to either of these, Internet is blazingly fast… so my problem here is the Wireless portion.
As some background, here is how we had the network set up in the previous house which was working great (although it was wired for Ethernet which made things A LOT easier):
Airport Extreme (4th Generation)
Wireless Mode: Create a Wireless Network
Internet Facing (Connected to the Cable Modem)
Location: Upstairs Utility Closet (with Smartbox and cable modem)
Time Capsule (1st Generation)
Wireless Mode: Extend a Wireless Network
Joined to existing network above, but also connected to the Ethernet jack
Location: Upstairs Office
Here is the current set up we have running:
Time Capsule (1st Generation)
Wireless Mode: Create a Wireless Network
Internet Facing (Connected to the Cable Modem)
Radio Mode: 802.11n (b/g compatible)
Location: Upstairs Office
Airport Extreme (4th Generation)
Wireless Mode: Extend a Wireless Network
Joined to existing network above with NO incoming Ethernet connection
Location: Downstairs Family Room
My understanding is that the Airport Extreme should pick up and relay the signal downstairs, as well as provide the router for the devices downstairs that need Ethernet (TiVo, Apple TV, etc).
So, my question is (and thank you in advance for helping me sort this out!), what would be the best configuration to optimize the Wireless performance in the house?
Also, for whichever device is the one picking up the existing network and providing the router capabilities for the Tivo and such, is it possible for it to pick up but not rebroadcast the signal? I think in this new house we may have a good enough signal from the office, without the need to rebroadcast it. My theory is that in this house, they are too close together and interfere with each other and/or devices aren't sure which to choose so they bounce back and forth endlessly. Again, just a theory.
Many thanks again for your help! If I've left out any information, please ask and I can provide.

Should they be running on the same channel (as with the "Extend" option previously? Or just both on Automatic channels?
I would recommend the Automatic setting on both devices because this will allow each router to scan and choose an open channel automatically. If you want to set the channels manually, keep them separated by at least 4-5 channels. You would not want to ever use the same channel for both devices in this type of "roaming" setup.
Is there a way to limit bandwidth per device (or action) so that it doesn't monopolize the network and keep other devices from using it?
Nothing that I am aware of. It sounds like you have some young users who are likely visiting Bit Torrent sites, which will really gobble up the bandwidth with big, heavy downloads. The Time Machine has to back up the same files again when it makes the next pass, so that clogs things up again.
Backups would go 3-5 times faster, on average, if the computer(s) could connect using Ethernet, but I understand that wires are not cool with the younger crowd.
should BOTH the TC and AE be set up in Bridge mode?
The AirPort Extreme should be set up in Bridge Mode.
The Time Capsule...it depends. If the TC is connected to a simple cable modem...then the correct setting for Connection Sharing would be "Share a public IP address" on the TC. That is because a simple modem has only 1 IP address to deliver. The TC takes that address and "shares" it with other devices by setting up a local network for all your other devices.
If the TC is connected to a gateway....a combination modem/router in the same box that usually has 3-4 Ethernet ports on the device....then that device would be considered the main router on the network and the TC would be configured in Bridge Mode in that case to function correctly on the network.

How to set up Airport Extreme for 11ac and 11n?

I have just purchased the new Airport Extreme (August 2014) because Apple's website states
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
I have number of Macs in my home from a new MacBook Pro with Mavericks to a Macbook Air with Snow Leopard (due to required software) and iPads.
So after setting up the new Extreme my new MacBook only accesses 11n as does my older Macs. I checked by holding down the option key while clicking the WiFi icon at the top of my Mac. Well, not so automatic then as I was expecting 11ac and 3 times faster access (as stated by Apple).
I then looked for some documentation for setting up but cannot find anything.
Hence my question here.
How to set up Airport Extreme for 11ac and 11n simultaneously?
At present the new Extreme is no better than my previous 2 year old one.
Thank you.
Michael

How to set up Airport Extreme for 11ac and 11n simultaneously?
Assuming that it is operating correctly, 802.11ac and 802.11b/g/n are broadcast simultaneously by default.
Simultaneous dual-band support.
AirPort Extreme features simultaneous dual-band 802.11ac Wi‑Fi. That means it transmits at both the 2.4GHz and 5GHz frequencies at the same time. So no matter which band your wireless devices use, they’ll automatically connect to the best available band for the fastest possible performance.
That is advertising. The real information is usually found in the small and hard to read footnotes:
Based on theoretical peak speeds. Actual speeds will be lower.
AirPort Extreme is based on an IEEE 802.11ac draft specification. Performance based on comparison with Apple’s 802.11n products. Comparison assumes AirPort Extreme network with 802.11ac-enabled computer. Speed and range will be less if an 802.11a/b/g product joins the network. Accessing the wireless network requires a Wi‑Fi-enabled device. Actual speed will vary based on range, connection rate, site conditions, size of network, and other factors. Range will vary with site conditions.
Since the 802.11ac signal is being broadcast only using the 5 GHz band, some users report that they have had better results by using the option to assign a different name to the 5 GHz band, and then pointing their Mac to that specific signal or network. You may want to try that option.
But first as a test, please locate the MacBook Pro about 10-15 feet or 3-4 meters from the AirPort Extreme with clear line-of-sight between the two devices. Restart both the AirPort Extreme and the Macbook Pro and then check to see if the Mac is connected to an 802.11ac signal.
If not, please power off your other wireless devices...computers, mobile devices, etc. temporarily, and try the same test again.
Please report on your results.

Problems with Bonjour, Airport Extreme and OS 10.4.3

I have a networked, HP Photosmart 8450 printer. The printer was connected to both an iMac 20" and PowerBook G4 15" running OS 10.4.3. Yesterday, I lost the ability to print from the PowerBook. I have identified it as a problem with my Airport Extreme connection.
The iMac can see the printer just fine, and it shows up using Bonjour when I browse printers in the Printer Setup Utility. The PowerBook, however, cannot see the printer - that is, it does not show up in the browser, but only when I use the Airport connection. However, when I connect the printer to the PowerBook via USB, or when I plug a network cable in to the PowerBook, it sees the printer immediately using Bonjour.
It appears, then, the problem is with my Airport Extreme card. Has this issue been identified by anyone else/Apple? Perusing the discussion boards, it seems others have had this problem.
PowerBook G4/iMac Mac OS X (10.4.3)

Thanks for the response, however, my question remains: I'm wondering if anyone else with an Airport Extreme ("b" version) and OS 10.4.9 installed has a problem using Admin Utility 4.1.1 and/or Airport Setup Assistant 4.1.1? Specifically, the problem is, after resetting the Airport Extreme, I was able to set it up using the Setup Assistant (establish the network, set the password), but thereafter, it does not show up in the Admin Utility at all (but the Extreme's lights flash as it is being accessed) and in Setup Assistant, it shows up, but there are "errors" when trying to change settings. It is very odd.
When I was running 10.3.9, I had had no problems setting up/administering my Airport Extreme. Suspecting the Extreme itself, I even had an Apple Genius inspect it at the Apple store, but it was pronounced in working order. I might try to check the Airport card inside the G4 (by trying it in a friend's G4). If this communication problem is not shared by anyone else (ii.e., a software issue), it could be my Airport card.

Problem to configuring Airport Extreme

Hi, first of all I'm sorry for my bad english.
Well, I've a problem with my Airport Extreme: I bought last month an iPod touch, really beautiful.
I wanted to connect to my Airport Extreme, but It is configured with the following settings: 802.11n (5 GHz). Now, to connect my ipod, the Airpot Extreme base must be set to 502.11g / b, but if I change the settings my iMac Core 2 duo (MacOSX 10.5.1) does not see the Airport Extrem base.
The iMac see other router configured to 802.11g/b. So it's not a problem of my iMac and even of my ipod. I think it's a configuration problem.
Someone can help me?
Thanks to all.

Sorry - ambiguous choice of words on my part.
What I meant to say is - the problems you are having seem to be isolated to this iMac, so any attempt to fix the problem needs to be focused on the iMac rather than the base station or your other computers. Unfortunately, I can't help you much with figuring out what the problem with your iMac is - which may not be fixable by simply "reconfiguring" something on the iMac.

Problems setting up Airport Extreme w/o wireless card

Similar Messages

Maybe you are looking for