Set up Airport Extreme with 2 Airport Express connected by CAT5??

I recently bought an Airport Extreme base station and an Airport Express. My plan was to use to Airtunes with my AV receiver in my basement. Unfortunately, because the distance between these two areas is long (and separated by two floors) I'm not able to get a strong enough signal with the Airport Express to use Airtunes. I bought another Airport Express to put on the middle floor of our house but the signal in the basement was still not strong enough even with this addition.
I do have a way of connecting the middle floor of our house with the basement area by a CAT5 ethernet cable. My plan now is to connect the two Airport Express modules by their ethernet ports with this cable. The Airport Express on the middle floor connects with the Airport Extreme base station wirelessly without any problems. My question is what is the proper setup for the 2nd Airport Express connected by ethernet in my basement.
Airport Tech support said this could be done. They recommended setting up a new wireless network with the 2nd Airport Express by "fooling" into thinking it was connected directly to the router but using the same network name with a different wireless channel as my Airport Extreme base station. This setup actually works for several hours but then the Airport Express module that is connected to the Airport Extreme blinks amber. Interestingly the 2nd Airport Express with usually remain with the green light on.
Does anyone have any suggestions for the best way to set this up regarding network configuration with the Airport Utility?
Thanks

wmskaggs, Welcome to the discussion area!
They recommended setting up a new wireless network with the 2nd Airport Express by "fooling" into thinking it was connected directly to the router but using the same network name with a different wireless channel as my Airport Extreme base station.
That will work with as long as the AirPort Express (AX) is connected via Ethernet. The only other setting you need to make is to configure it to act as a bridge (not sharing a single IP address).
If this one looses connection, then something is wrong with the AX or the Ethernet connection (cable and/or connectors).

Similar Messages

Can you guide me step by step in setting up airport express as a wireless extender for an existing Airport extreme network

Can you guide me step by step in setting up airport express 802.11 as a wireless extender for an existing airport extreme network?

Also check out:
Re: Need Help Networking AirPort Exp to Existing AirPort Extreme
Re: How to connect AirPort Express to existing AirPort Extreme Network...

How to set up Airport Express in Bridge mode for hotel use

Please provide step by step instructions on how to set up Airport Express in Bridge mode for hotel use. I do not have a computer with me, only an iPhone and AEX 802.11n.

+"Please provide step by step instructions on how to set up Airport Express in Bridge mode for hotel use. I do not have a computer with me, only an iPhone and AEX 802.11n."+
AirPort Utility is the application that must be used to setup and make any configuration changes to the AirPort Express. I'm not aware of an "App" for this.
If you could borrow a computer from someone there for 30 minutes or maybe use the computer in the lobby, you could download AirPort Utility and reconfigure your Express. To help with setup, use an ethernet cable from the computer to the Express to help AirPort Utility "see" the Express.
http://support.apple.com/downloads/#airport

Why does 2 Airport Expresses connects to one another instead of connecting to the primary Airport Extreme For internet Connectivity ?

I have Netgear DG834G router only for dsl connectivity wifi connectivity to that router is off. i have connected netgear that provides adsl connectivity to the (Shakeel's Airport Extreme) Airport Extreme dual band Wireless N 5th generation via cat 5 cable so airport extreme is the main wifi device through which i get wifi signals at my home. now our house is big and i have installed the adsl netgear modem and airport extreme router at the same place in my room in the upper story but the signals are weak even in the upper story at the other end of the house so i have installed the new airport express dual band wireless N in the upper story (Kafeel's airport express) and it is connected to the primary airport extreme (Shakeel's Airport Extreme) wireless router in range extention mode it repeats the same ssid. Our ground floor has another airport express dual band wireless N the new one ( Lounge's airport express) signal was weak there so i installed another airport express (Lounge's Airport Express) their and configured it to extend the range of primary router airport extreme (Shakeel's Airport Extreme) in the upperstory with the same ssid. Now the problem i am facing that sometimes lounge's airport express connects to kafeel's airport express instead of connecting to the airport extreme and the signals in lounge are weak because all the devices are connected to kafeels airport express and does not connect to lounge air port express. but when lounge airport express is connected to primary router airport extreme then everything works fine devices connect to lounge airport express and signals are full. i have took pictures of the problem i am facing you will understand better by having a look at it. In normal working setup both the airport expresses are connected to airport extreme which is shown in this picture
The second picture shows when lounge airport express is connected to kafeels airport express and not the airport extreme (Shakeel's Airport Extreme) this is the problem.
isnt there a way to correct this so that they dont connect with each other and connect to the airport extreme ?

Lounge's AirPort Express must be located signficantly closer to Shakeel's AirPort Extreme than it is to Kafeel's AirPort Express, and there must be fewer obstructions in the signal path than the other possible connection.
The reason is that if you want Lounge's AirPort Express to connect to Shakeel's AirPort Extreme, it must receive a significantly stronger wireless signal from Shakeel's AirPort Extreme than it does from Kafeel's AirPort Express.

Trouble setting up Airport Express and Windows

I am trying to help a friend set up Airport Express to work with her Windows computer. The goal is to use the Airport Express so she can stream iTunes to her stereo system. There is an existing Linksys wireless network. First I tried to connect add the Airport Express to her existing wireless network. I was able to see the base station and I chose to add it to her existing network. I was able to go through all the steps updating the Airport Express. After the base station restarted, the configuration tool couldn't see the base station anymore. In iTunes on her Windows computer, I could see the base station but when I clicked to select the speakers, it wouldn't select.
I reset the Airport Express to factory settings and tried again with the same result.
I reset again and tried using the Airport Express to replace her wireless network and to also stream iTunes. In the configuration app I chose to create a new wireless network. I was able to set up the Airport Express as a wireless network and could connect her Windows laptop to the Internet through the Airport Express. But I had the same problem in iTunes: I could see the speakers in the drop down list, but I couldn't select them.
I've returned everything to how it was (Linksys wireless network).
Can anyone let me know how to make this work?
Thanks

As I mentioned in my post, I followed the directions exactly. I used the same set of directions in the previous post. At the last step of the set up, the Airport Express restarts. After restarting, I got an error saying the utility could not find the base station. I reset the Airport Express to factory settings and went through the steps again and had the exact same result.
I am using an Airport Express at home with a Linksys router and I had no problem setting it up to join my network. The only difference is that I use a Mac at home. The one I am trying to set up for my friend is with a Windows XP machine.
Has anyone ever had this problem?

Had a Airport Express connected to my stereo and it was working. I brought an Airport Extreme and suddenly it took over and Airport Express stopped working and disappeared from Airport Utility. What I am supposed to do? ar2ro

I have an Airport Express connected to my stereo and it was working without any problem.
Recently I bought an Airport Extreme to use it as my Base Unit connecting it to my DSL.
I followed the instructions of the Airport Utility, and it started working.
Suddenly, problems started happen the Airport express that was connected to the stereo , stopped working and it disappeared from the Airport Utility area , as it did not exist in the network. I tried to reset it but it did not appear in the Airport Utility page.
Apparently I have other problems with the private network that it created because I cannot use it because of problems with the password that was created. I can only use the network that I created for my guest...
I dont know if my problem is a configuration problem or there is problem with the equipment.
I read that other users where having the same problem with the Airport express , using non apple equipment as their base unit , but I thought that using the Airport Extreme was going to be compatible and no problems would happen.
What should I do?

Common Problem. Common solution.
Connect your Express via ethernet cable to the Mac while other network connections on the Mac are switched OFF.
After the Express shows up, change the settings of the Express to join the existing network. Take the appr. settings.
Unplug and reconnect your Mac to the network.
Check if the Express shows up in Airport Utility
Alternative solution:
Hardreset the Express to factory settings
(while on power push the Pin next to the audio plug with a paperclip. Plug out the Express still holding down the little button then replug the Express to power and release button)
After that, the Express will show up in the Airport Utility.
Make all needed settings.
I would prefer the first solution, its easier just to plug a cat5 cable.

How to extend range of my wireless network with an Airport Express connected by ethernet with Airport Utility 6.0

Hi everyone,
I have AirPort Express 802.11n (1st Gen) firmware 7.6.1, that is connected to my main wifi base station (a TimeCapsule) by ethernet. I would like to extend the range of the Wifi Network but am not clear on how to do so using the new interface of Airport Utlity 6.0.
Does anyone have any tips on how to do this?
BR
AK

Hi Everyone!
Many thanks for the tips. I have downloaded 5.6 and have set my Airport Express in the "Extend a wireless network" mode. I was still having a few problems with the quality of the wifi connection in different parts of my apartment (by no means a very large one, but walls seem to be made of extra dense concrete here in Singapore) and went out and bought a few powerline adapters by TP Link (http://www.tp-link.sg/products/details/?categoryid=1862&model=TL-PA211#spec).
If you don't mind a slightly long post, I would be very grateful for any tips:
My setup is now as follows:
Main room
Time Capsule - connected to a Cisco DPC3925 Modem (http://www.cisco.com/web/consumer/support/modem_DPC3925.html) both connected to a TP Link adapter 1.
iMac - connected via Ethernet to TP Link adapter 2 and wifi enabled
Airport Express 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1) used to stream audio to a stereo that doesn't have an optical cable input. Since it is an Ethernet connection, I have wifi turned off.
Apple TV 1 - connected by Ethernet to TimeCapsule (and thus TP Link adapter 1)
Bedroom A
Airport Express 2 - connected via ethernet to TP Link adapter 3
Bedroom B -
Apple TV 2 - connected by Ethernet to a TP Link adapter 4
After following the tips on setting up the extended wifi network, I find that when I use a wireless client (e.g. iPad, Macbook air, etc) in either Bedroom B or Bedroom C (both don't have wifi in the room) the connection is very poor. Even more odd is that the connection in Bedroom A, one that does have Airport Express 2. To be clear when I mean very poor, I mean Skype/facetime skips frames and freezes... this doesn't happen when I am in the main living area.
I would be very grateful for tips on how to set up the most robust network given the configuration above. Specifically, I am wondering about:
When I select Extend a wireless network option on Airport Utility 5.6 the summary page states that it is connecting using "Wireless Network" vs what I would expect it to say "Ethernet connection".
Is there any advice on whether to enable 5Ghz network and if so, should I try to use that for the various wifi clients?
Does anyone know if I can somehow use Apple products to extend the reach of the Cisco DPC3925? Frustratingly the signal is quite strong (compared to Apple routers), but I cannot properly stream audio/video if that wifi network is used (as my iMac that hosts the content is on the Apple one... and I'd have to walk over to switch it to the Cisco one).
Any other tips would be much appreciated!
Cheers!
AK

Airport express connect with Imac via lan line or can not?

I using IMac with connect to internet with DSL modem router (having 4 lan ports).
Now I put Airport express connect with one of Lan ports from DSL router and still connect my IMac with DSL router via lan line and still connect to internet via lan line (switch off airport function in Imac).
The Airport express is using for provide wireless internet and printer to my other PC.
My Question is can I still set up as above and connect share file to my PC via airport express?
Forget to tell that I'm very newby to mac.

chounws, Welcome to the discussion area!
Yes you can do that. Configure the AirPort Express (AX) to operate in bridge mode (not sharing a single IP address).

Problems setting up AirPort Express Base Station

I'm a real newbie at this, so pardon the ignorance in advance haha.
I just bought a new Airport Express base station. I wanted to be able to stream my music via iTunes to my living room. I'm just having problems getting the aiport utility to recognize the base station. I have the base station plugged in and everything. Right now it is flashing the amber light.
This is my set-up. I have a Netgear WGR614 54MBPS wireless G router connected to my broadband modem. From the router I have it connected to my desktop thats running windows xp pro. The network is up and running just fine. I can connect via any laptop or other device with wifi. Now, how do I get my wireless router to pick up the base station? Do I have to wrong idea here or something? haha. thanks in advance!

In the Airport Utility for your Airport Express, you should set the Airport Express in "client" mode. You might have to connect your Airport Express directly to your router with ethernet cable, while doing this. If you are using encryption, make sure that you enter the encryption number onto the express that your router/access point is using. Again, if you plug the Express directly into the router, you should be able to modify the settings quite easily. Once you unplug the express, it will blink orange for awhile (maybe a minute), so wait a bit.
Good luck.

Problems Setting-up Airport Express to Play Music thru External Speakers

Hi:
I have an HP dv6500z laptop connected to an HP printer C6280 via LinkSys wireless network using the LinkSys 54G router and PrintServer. It works fine.
I purchased an Apple Airport Express and want to connect it to this network so that I can play songs from within iTunes through external powered speakers wirelessly. The powered speakers are connected to the Airport Express (AE).
The AE is plugged into the AC outlet and the speakers are turned on. The AE is roughly 10 feet away from the laptop/router, just across the room. The AE's
LED is flashing amber (It does not yet recognize the network). I installed the Airport Utility from the enclosed CD, downloaded all patch upgrades and it installed successfully.
Now, how do I tell the Airport Utility to recognize and connect to my existing LinkSys network, so that the AE recognizes it ? The instructions are not clear on this note...they say to run the Airport Utility and then follow the on-screen instructions. The instructions tell you that you will lose your wireless network connection if you continue...and you do if you try.
The same information comes up if you try to do a manual install.
How do I connect the AE to an existing network ? This information seems to be missing. If I go to the AirPort Utility Help and search and search on Setting Up AirPort Express, it tells me the following:
Connect your stereo or powered speakers to your AirPort Express using the mini-jack on the top side of your AirPort Express, and then plug your AirPort Express into a wall outlet.
Open AirPort Utility, located in the Utilities folder in the Applications folder on a computer using Mac OS, and in Start > All Programs > AirPort on a computer using Windows.
Click Music in the toolbar, and select the Enable AirTunes checkbox.
Problem: What Music in What toolbar ? I do not see this...
Enter an iTunes speaker name and password. This is the name displayed in the pop-up menu at the bottom of the iTunes window.
Problem: Where does this information come from
If you're setting up your AirPort Express for the first time, choose Assist Me from the Base Station menu and follow the onscreen instructions.
It seems like something is missing from the setup.
Aaah...Just for the heck of it, I went under Base Station > Assist Me
and told it to continue even though the dialog box said it would change the network.
It displayed a tabbed dialog box where I could configure the AirPort Express, including a tab named Music.
Note:
The following two items are listed in Apple's on-line Help inside of Airport Utility, and on the web, yet I did not see them inside of Airport Utility when trying t oconfigure my AE.
I did not see a checkbox to check, named Enable AirTunes.
I did not see any place for entering the name and password for my speakers.
I followed all of the instructions and things looked like they were going well until I clicked Finish.
Them it said something like it could not save the settings..try again.
Well, I did, but when I brought Airport Utility back up, it kept saying that it could not detect the AE,
and when I went under the Base Station menu, all items were grayed-out, so I couldn't do anything.
Please help... the instructions need to clearer and more detailed.
Thanx, Dale
HP dv 6500z Windows Vista New Airport Express

Hi:
Thanx for your reply.
After several more hours of trial & error over the weekend,
I finally have the Green Light (LED) on the Airport Express.
And it stays green, even if I unplug it from the AC outlet,
and plug it back in later. I have the green light so this
tells me that I have gotten past one hurdle.
OK...in order to get this far, I had the AE wired to the
laptop or LinkSys router via an Ethernet cable. How do
I go about making this a "wireless" connection. LinkSys
told me how to take my laptop from a hardwired connection
to wireless, but it doesn't address the issue when you have
a 3rd party device hardwired that you want to make wireless.
Side Note:
I have not tried this yet, but I found a note on the web that
stated something like this: after getting the green light,
this guy then disconnected the Ethernet cable from the AE,
unplugged the AE from AC power for a few minutes, plugged it
back in to AC power, and voila! ... he was wirelessly on his network.
OK...let's assume that my AE is now on the wireless network.
What type of special settings do I need to make inside of iTunes
in order to get sound to the speakers.
I have my powered speakers recognized by iTunes...I can select them.
But, it appears that something may be blocking my AE from talking to
my network...I keep getting a pop-up box from Symantec saying that it
is detecting a "virus" (for lack of a better term) at the IP address
that I set my AE to. Oh, yes...that's another question...
When manually setting up the AE, I have my router network's IP address
(dotted-quad) in the list of parameter settings, but...near the top of
the list, the Airport Utility software asks for your AE's IP.
Well, what is it ? Nobody has told me ... Where do I get it from ???
Or...do I assign an arbitrary value to it based on the dotted-quad below ?
The router has an IP address of something like 192.168.1.xyz. I know what
the xyz is for the router but, what number do I use here for the AE, or
does it matter as long as it isn't being used by another network device.
My network is static.
So, after using a number not used by my network elsewhere (that I am aware of,
and...inserting a $ (to specify hexadecimal format)in front of my encryption password, NOT the router password (they intermix the naming of these) I finally managed to get the Green Light on the AE. Note: I am using the WEP-64 bit encryption which is also refered to a "40 bit" (No..not hexadecimal..$40 = 64) which is 40-bit to which a random 24 bit is added to give you 64 bit encryption.
To summarize;
I appear to have the AE configured via hardwire (I have the green light).
In iTunes, I can see and select my powered-speakers from the drop-down menu in the lower right corner, but i am s not yet streaming (hearing) the music.
It appears that Symantic may be knocking me off the network, or not letting the AE talk to the laptop/router...I have not yet tried this, but another nugget that I found on this site says to go to System Preferences (where?), click on the Firewalls tab, click Advanced , and uncheck "Block UDP Traffic".
Is this what may be blocking my AE talking to the laptop/router ?
Any help/feedback would be appreciated...Thank you.
I'm getting close...but no cigar (yet).
DaleB

I set up Airport Express as Client, I can no longer connect to my wlan

I set up Airport Express in Client mode so that I could use Airtunes. My Router/modem is a netgear one and I use WPA.
I can no longer connect to my wireless network from my ibook.
If I plug in the ethernet to the router I can. I can also then see from the router that Airport express has connected itself to the router.
So what do I have to do to be able to reconnect to myibook to the WLAN?

Double-check these settings on your iBook:
System Preferences > Network > Show > Network Port Configurations
- Verify that an AirPort option exists. If it does not, click "New" to create one. - Verify that AirPort is "On" (checked)
- Verify that AirPort is at the top of the list. If it isn't, you can drag it to the top.
Systems Preferences > Network > Show > AirPort
AirPort tab
- By default, join: Automatic
TCP/IP tab
- Configure IPv4: Using DHCP
- Configure IPv6: Automatically or Off
Proxies tab
- Configure Proxies: Manually
- Select a proxy server to configure: <All proxies should be unchecked unless you specifically require a proxy for Internet access.>
- Exclude simple hostnames (unchecked)
- Bypass proxy settings for these Hosts & Domains: <leave blank>
- Use Passive FTP Mode (PASV) (checked)

HT4259 Trying to set up airport express to extend my wireless network. Primary base station is a time capsule. Even when I plug in the airport express to mac it cannot find it.

Trying to set up airport express to extend my Wi-Fi network. Primary base station is a time capsule. Tried searching for airport express using Wi-Fi status, no luck. Even tried plugging airport express into iMac, still no luck. Airport express showing solid amber light. Thanks for any help.

Airport express showing solid amber light
Unfortunately, this can mean one of two things:
1) The Express is locked up and will need a Factory Default Reset procedure to try to return the device back to its original default settings so that it can be reconfigured again.
2) The Express is defective. If you cannot get the Express back to a slow, blinking amber light after a Factory Default Reset, the Express will need to be replaced.
Try the Factory Default Reset a few times and report back on your progress.
Resetting an AirPort Base Station or Time Capsule FAQ

Time Capsule with (2) AirPort Express connection problem

I have (1) Airport Time Capsule with (1) AirPort Express connected. I'm trying to connect another Airport Express but only get a yellow light on the 2nd Express. If I connect it with a ethernet cable I get a green light. How do I connect a 2nd Express?

The 2nd Express needs to be about the same distance from the Time Capsule as the 1st Express....and....it cannot be closer to the 2nd Express than it is to the Time Capsule.
The reason for this is that the Express will pick up the strongest signal and you want the Express to pick up the Time Capsule signal to be able to extend it.
Then, start over as LaPastenague instructs on the 2nd Express and configure it again.

Apple Airport Express connection/setup with Siemens SpeedStream 4200

Hi, i am having trouble getting my macbook pro to recognise the Apple Airport Express connection to broadband via the Siemens Speedstream 4200 supplied by Optus.

and make sure you choose PPoE when you set up your router.
(It's not obvious from the Optus paperwork)

I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

I can not join my Apple extreme with the Apple express. I shows a conflict in the network! I've tried everything. How can they join on the same network?

It says that my DHCP has to be changed! How? to what?
It is 802.11g.express. but is set to default by the computer (Macbook Air).
The other is 802.11n. (express)
Extreme is 802.11.g. Is the Main Airport.
It is on ethernet & wep 128 security.

Set up Airport Extreme with 2 Airport Express connected by CAT5??

Similar Messages

Maybe you are looking for