Problems with 7.1.6 on windows and foxfire

I saw the answers about the problem of a ? when you go to a site with a quick time file. I can play some file that is quick time but when I go to a site that has a quick time Q on it, I get a ?. I read where no one has this problem with foxfire. I do! Can anyone advise?
Thanks, Dawleen

I had a driver conflict with the Quicktime 7.1.6 upgrade. I had to use an older driver. They have not figured out how to roll back the update.
It appears the conflict is with some Nvdia graphics drivers in my case.

Similar Messages

  • I  have a problem with the synchronisation of my iPhone and iPad with Outlook 2007 on my 64-bit Windows 7  PC. For several years, I have had no problems with the synchronisation by cord connection and iTunes between these programmes. However, a few months

    I  have a problem with the synchronisation of my iPhone and iPad with Outlook 2007 on my 64-bit Windows 7  PC. For several years,
    I have had no problems with the synchronisation by cord connection and iTunes between these programmes. However, a few months ago I decided to use Mobile Me. However, there were problems with duplication of calendars and then “rogue events” – which could not be deleted – even if deleted on Outlook and on the iPhone (or both at the same time) – they would just reappear after the next synchronisation.  All other synchronisation areas (eg Contacts, Notes etc) work fine.
    I have looked for help through the Apple Support Community and tried many things.  I have repaired my Outlook. I have repaired my .pst file in Windows. I have re-installed the latest version of iTunes on my PC. I have re-installed the firmware on my iPhone. I have tried many permutations on my iPhone. I have closed down all Mobile Me functions on the iPhone. I have spent upwards of 24 hours trying to solve this problem.
    What am I left with? Outlook works seamlessly on my PC. My iPhone calendar now has no events from  my calendar, but does not synchronise through iTunes. Nor does it send events initiated on the iPhone to the Outlook. I am at the point of abandoning iPhones and iPads altogether.  I need to have a properly synchronising calendar on my phone.  Do you have any suggestions?

    In the control panel goto the "Lenovo - Power Manager" and click the battery tab, there is a maintenance button in there that will let you change the charging profile for your battery.   (from memory, so exact wording may be off)
     The lower the numbers you use there, the longer the battery *should* last.    These batteries degrade faster at higher charge levels, however storing them at too low of levels is also not good for them... I've read that 40% is optimal, but just not realistic if you use your computer.
    --- ThinkPad T61 / Win 7 / Core 2 / 4gb RAM / Nvidia / Still used daily --- ThinkPad Edge 15/ i5 / Win 7 / TrueCrypt / 8gb RAM / Hated it, died at 1 yr 1 mo old --- ThinkPad T510 / Win 7 / TrueCrypt / i5 / 8gb RAM / Nvidia / Current primary machine --- ThinkPad X220 / i7 / IPS / 4gb / TrueCrypt / My Road Machine

  • Problem with tv@nywhere plus on windows 8

    hi
    i have a problem with tv@anywhere plus on windows 8. i can setup the pvr plus app completely but when i open that and click on "watch and record dtv program" icon, i will see an error that says: "invalid class string!"
    i think this problem should be for its driver because i'm using windows 8 64bit and the driver is for windows 7, i couldn't find an appropriate driver for windows 8 on MSI driver downloads, as matter of fact it didn't exist.
    so what should i do for my problem?

    I'm afraid TV@nywhere Plus is a bit outdated for Win8. There is no update so far since 2010. Could be MSI won't add Win8 support if it would be anyway possible.

  • I am facing problem with adobe illustrator cc in windows 8,it closes automatically after few secons,please help

    I am facing problem with adobe illustrator cc in windows 8,it closes automatically after few secons,please help
    [ link removed by moderator ]

    Sign in, activation, or connection errors | CS5.5 and later
    Mylenium

  • Problem with changing Label in Bridge CS3 and CS6

    Hi there,
    I am having some problem with changing Label in Bridge CS3 and CS6 in windows.
    1. In Bridge CS3 (Windows XP), most of the time with most of the files, there is no problem. But I found that in some files, the Label does not get changed. I usually change Label by right clicking on the picture, then Label and select any Label. When I do so in those files, nothing happens. But when I rename the file by changing or adding just a single character, then it works. And if I again rename to original name, it still works. But without renaming the Label does not change. Again this does not happen with all pictures, but occationally with some. We usually receive pictures from different clients for editing purpose.
    2. In Bridge CS6 (Windows 7), if you create lot of Path using Pen tool in Photoshop for the purpose of removing background, you save the file, close, and change Label in Bridge, again open the file in Photoshop, you see no Path in the Path Pallette. So that means, changing Label works, but it removes the Path from the file. But if there is small amount of path, then no prboblem. But if there is lot of path, like you need to create for a necklace to remove background, then the problem arises.
    I am using Bridge for a purpose where it is very helpful so I really need to use Bridge, and Labeling feature is the most important to me, but after feaguring out this problem, I am really tensed as to whether or not I will find a solution to this. So any help, guidance will really be appreciated.
    Thanks very much in advance for any solution.
    Best regards

    I have re-checked the issue and I found that the problem is with JPG file.
    I wasn't even aware you could save a path to a jpeg file (always use PSD because of wanting to keep the Alpha Channel, jpeg only can contain 1 layer and no alpha channels and/or transparency).
    However I tried it on a file with a simple path and one with a complex path. It seems indeed you have found a bug. The simple path is no problem but the more complex path is indeed disappearing.
    It is not only label but also rate or adding IPTC in the description field. The moment metadata is saved to this jpeg file and reopened the earlier present work path of a more complex path is gone.
    Despite the fact that to my opinion a jpeg is not the most suitable file format for saving a work path this should not happen. If a work path is saved to a jpeg then it should be kept saved after just altering metadata in Bridge.
    It still is the same behavior in Bridge CC because that is what I use. Don't know when it started but it still needs to be repaired
    Here is the link for filing a problem or bug:
    http://feedback.photoshop.com/photoshop_family/

  • Does anyone still have problems with Premier Pro on Maverick? and is there any known fix?

    Does anyone still have problems with Premier Pro on Maverick? and is there any known fix?

    I know OSX 10.9 Mavericks introduced a power saving feature called App Nap which is meant to slow down applications that it determins are inactive (or when minimized). This would mostly likely cause problems if you're dynamically linking After Effects comps to your timeline or sometimes exporting to Media Encoder.
    Try disabling App Nap for all your Adobe App files...
    Go to your Applications folder
    Go into individual Adobe app folders (ie. Adobe Premiere Pro CC)
    Right-click on the Adobe app file (ie. Adobe Premiere Pro CC.app) and select Get Info
    When the info window opens up, add a checkmark beside "Prevent App Nap"
    Restart the application
    This fixed all my performance issues.
    -Pete

  • Problems with "no color" in the "Fill and Stroke"

    I am having problems with “no color” in the “Fill and Stroke” function of Flash CS4 Pro.
    I had been using CS4 for 10 days and everything worked fine. Then I tried experimenting with various color combinations (along with “no color”) for “Fill and Stroke” for a simple button. Suddenly CS4 locked up on me while I was working with the “color panel”. A second color panel appeared in the upper left corner and the program was not responding. All I could do was to end the CS4 task.
    After that, whenever I created even a simple rectangle, at first the colors would appear as indicated for “Fill and Stroke”, but when I selected the object to see its properties, either the stroke or the fill color box would have a red slash line, indicating a “no color”, and I couldn’t select the color box to change it using the ink bottle tool, although the other box worked fine.
    Rebooting did not help. So I uninstalled CS4 (and didn’t keep the preferences), rebooted, then reinstalled it. The problem was still there. Logging on as another user didn’t help. I tried restoring the Windows system to before I installed CS4 and resinstalling it and that didn’t work. I have a disfunctional CS4 now and I don’t know what to do to fix it. Please help me. Thank you.

    Have you updated flash to 10.0.2?  Have you played around with a bunch of different selections, objects, and so forth to see if this box is always incorrect?  I think there's some particular selection (order of selecting things, and so on), where the color swatches in one location don't work as expected. However, it should not happen all the time and from what I recall it was fairly easy to work around (I can't even figure out what this was - so probably not it, as it seems hard to run into or perhaps now fixed).
    Also make sure you have the stroke selected - if you don't have everything selected, either the fill or stroke will show no color and dim depending on the selection.

  • Hi, I have a problem with fonts because in the window I can't see the font, they are transparent. how can I fix this?

    Hi, I have a problem with fonts because in the window I can't see the font, they are transparent. how can I fix this?

    giadad,
    It sounds as this issue:
    Open System Preferences and go to Accessibility. Next, select Display from the source list along the left, then check the box labelled Reduce transparency.
    It was first presented in this post #15 by TheUlser:
    https://forums.adobe.com/message/6854594#6854594
    It has been described on this Adobe page:
    http://capitalmacservice.com/font-preview-working-illustrator-cs-5-yosemite-fix/

  • HT201210 i have problem with the firmeware file...and I do not know what is that

    i have problem with the firmeware file...and I do not know what is that

    Make sure you are updating your phone the correct way, by connecting to iTunes and clicking Check for Updates on the Summary tab of your iTunes sync settings.  Do not try to download the firmware file from the internet first.  Also be sure iTunes is up to date before updating.
    Delete the existing firmware (.ipsw) file and try again.  You will find it at one of the following locations:
    Mac OS X: ~/Library/Application Support/MobileSync/Backup
    Windows XP: %AppData%\Apple Computer\MobileSync\Backup
    Windows Vista: %AppData%\Roaming\Apple Computer\MobileSync\Backup
    Windows 7: %AppData%\Roaming\Apple Computer\MobileSync\Backup

  • Hey Guys i have a problem with my mac since last month and it wont boot up it freezes in a grey apple logo and and spinning gear any body know how to fix this?

    Hey Guys i have a problem with my mac since last month and it wont boot up it freezes in a grey apple logo and and spinning gear any body know how to fix this?

    Take each of these steps that you haven't already tried. Stop when the problem is resolved.
    Step 1
    The first step in dealing with a boot failure is to secure your data. If you want to preserve the contents of the startup drive, and you don't already have at least one current backup, you must try to back up now, before you do anything else. It may or may not be possible. If you don't care about the data that has changed since your last backup, you can skip this step.
    There are several ways to back up a Mac that is unable to boot. You need an external hard drive to hold the backup data.
    a. Boot into Recovery by holding down the key combination command-R at the startup chime, or from a local Time Machine backup volume (option key at startup.) Release the keys when you see a gray screen with a spinning dial. When the OS X Utilities screen appears, launch Disk Utility and follow the instructions in the support article linked below, under “Instructions for backing up to an external hard disk via Disk Utility.”
    How to back up and restore your files
    b. If you have access to a working Mac, and both it and the non-working Mac have FireWire or Thunderbolt ports, boot the non-working Mac in target disk mode by holding down the key combination command-T at the startup chime. Connect the two Macs with a FireWire or Thunderbolt cable. The internal drive of the machine running in target mode will mount as an external drive on the other machine. Copy the data to another drive. This technique won't work with USB, Ethernet, Wi-Fi, or Bluetooth.
    How to use and troubleshoot FireWire target disk mode
    c. If the internal drive of the non-working Mac is user-replaceable, remove it and mount it in an external enclosure or drive dock. Use another Mac to copy the data.
    Step 2
    Press and hold the power button until the power shuts off. Disconnect all wired peripherals except those needed to boot, and remove all aftermarket expansion cards. Use a different keyboard and/or mouse, if those devices are wired. If you can boot now, one of the devices you disconnected, or a combination of them, is causing the problem. Finding out which one is a process of elimination.
    Before reconnecting an external storage device, make sure that your internal boot volume is selected in the Startup Disk pane of System Preferences.
    Step 3
    Boot in safe mode.* The instructions provided by Apple are as follows:
    Shut down your computer, wait 30 seconds, and then hold down the shift key while pressing the power button.
    When you see the gray Apple logo, release the shift key.
    If you are prompted to log in, type your password, and then hold down the shift key again as you click Log in.
    Safe mode is much slower to boot and run than normal, and some things won’t work at all, including wireless networking on certain Macs.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    *Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t boot in safe mode. Post for further instructions.
    When you boot in safe mode, it's normal to see a dark gray progress bar on a light gray background. If the progress bar gets stuck for more than a few minutes, or if the system shuts down automatically while the progress bar is displayed, your boot volume is damaged and the drive is probably malfunctioning. In that case, go to step 5.
    If you can boot and log in now, empty the Trash, and then open the Finder Info window on your boot volume ("Macintosh HD," unless you gave it a different name.) Check that you have at least 9 GB of available space, as shown in the window. If you don't, copy as many files as necessary to another volume (not another folder on the same volume) and delete the originals. Deletion isn't complete until you empty the Trash again. Do this until the available space is more than 9 GB. Then reboot as usual (i.e., not in safe mode.)
    If the boot process hangs again, the problem is likely caused by a third-party system modification that you installed. Post for further instructions.
    Step 4
    Sometimes a boot failure can be resolved by resetting the NVRAM.
    Step 5
    Launch Disk Utility in Recovery mode (see above for instructions.) Select your startup volume, then run Repair Disk. If any problems are found, repeat until clear. If Disk Utility reports that the volume can't be repaired, the drive has malfunctioned and should be replaced. You might choose to tolerate one such malfunction in the life of the drive. In that case, erase the volume and restore from a backup. If the same thing ever happens again, replace the drive immediately.
    This is one of the rare situations in which you should also run Repair Permissions, ignoring the false warnings it produces. Look for the line "Permissions repaired successfully" at the end of the output. Then reboot as usual.
    Step 6
    Boot into Recovery again. When the OS X Utilities screen appears, follow the prompts to reinstall the OS. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade.
    Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication.
    Step 7
    Repeat step 6, but this time erase the boot volume in Disk Utility before installing. The system should automatically reboot into the Setup Assistant. Follow the prompts to transfer your data from a backup.
    Step 8
    If you get this far, you're probably dealing with a hardware fault. Make a "Genius" appointment at an Apple Store to have the machine tested.

  • Problems with Mac OSX 10.5.2 and installing my pro tools le 7.1.1

    Problems with Mac OSX 10.5.2 and installing my pro tools le 7.1.1.
    My garage band & reason software don´t open anymore giving me a error messasge regarding the midi drivers in the operating system.
    Please help!!!
    Thanks,
    Paolo

    Somewhere at either Macworld or here I learned that DVDSP 2, DVDSP 3 and now DVDSP 4 "internally" are major re-writes.
    Support for HD among a few other items along with QT 7 which comes with Tiger means sincerely that one set of applications/OS is not going to be stable.
    Personally I think of all the issues possible its DVDSP vs QT.
    Unless you move to DVDSP v4 the alternative is to wipe the disk and go back to Jaguar (10.2) or perhaps Panther but avoid upgrading QT beyond 6. I advocate wiping the disk because I'n not sure an archive and install to down shift to an earlier version of the OS is possible. If it is I'd still worry about mis-matched files in all sorts of locations.

  • TS3694 good evening i have an problem with my iphone 4 the wif and network cant on now if i tray is showing iTunes i tray to reload the ios is showing an error -1 can you help me

    good evening i have an problem with my iphone 4 the wif and network cant on now if i tray is showing iTunes i tray to reload the ios is showing an error -1 can you help me

    No problem, glad to help!
    Update: my PC USB hub was connected to a USB 3 port, I connected the 30 pin cable directly to my PC, And the restore worked just fine. Restored phone from iCloud backup and seems to be working fine.

  • Hi I've a big problem with adobe acrobat reader XI pro and I hope you can help me. The problem is; when I past copied text from some pdf books (not all of them) it past symbols only! wherever I past it! and even if I coped that text from another pdf reade

    Hi
    I've a big problem with adobe acrobat reader XI pro and I hope you can help me.
    The problem is; when I past copied text from some pdf books (not all of them) it past symbols only! wherever I past it! and even if I coped that text from another pdf reader (adobe pdf reader, internet browsers, ...etc.).
    This problem started to happen since yesterday when I installed adobe acrobat reader XI pro to try it before I buy it, and before that when I was using the free adobe pdf reader I was totally able to copy any text from any pdf and past it anywhere with nothing wrong.
    What can I do?
    thank you a lot.

    There is no product called Adobe Acrobat Reader Pro. There is
    - Adobe Acrobat Pro ($$)
    - Adobe Reader (free)
    Which do you have? And are you a programmer?

  • I have a problem with simulation in Matlab 6.5 and LabVIEW for PID controllers

    I have a problem with simulation in Matlab 6.5 and LabVIEW. I have some methods for granting PID controllers in MATLAB to go but not LabVIEW. International Teams degree to transfer two but when I go past the fourth degree no longer work. We changed the formula for calculating the parameters for grade four and gave me some good values for Matlab award but when I put on LabVIEW have not settled. formulas are available in PDF and are. Please help me and me someone if possible. Thanks
    lim.4 generation parameters in MATLAB program and comparison methods are for second-degree transfer function.
    Solved!
    Go to Solution.
    Attachments:
    Pt net.zip ‏2183 KB

    This is the VIs what i try to make,but is not work. This pdf. document was used to create last VIs PID. thenk you for your colaboration.
    Attachments:
    PID create by me.vi ‏312 KB
    tut_3782.pdf ‏75 KB

  • With my i phone 4 , the Push notifications doesn't work for apps like (fb viber , whatsapp etc ) it only works for the official apps like message  even when im using the phone, has  this probleme with the iOs 6.0.1 and also with the iOs 6.1

    With my i phone 4 , the Push notifications doesn't work for apps like (fb viber , whatsapp etc ) it only works for the official apps like message  even when im using the phone, has  this probleme with the iOs 6.0.1 and also with the iOs 6.1

    This isn't an issue. Notice the screen prior to the one that shows usage has an iCloud section and a Manage Storage button. For this button to activate ios needs to download a few kb from icloud. Switching back to this screen forces ios to download those few kb.

Maybe you are looking for