Problems with Epson Stylus 3000 IP Ethernet

Problems with Epson Stylus 3000 IP Ethernet
The printer stops processing after reaching 1,72% of printing.
The Ethernet Cards led is on and blinking green.
I am running
Powerbook G4
OSX 10.4.5
Epson Stylus Color 3000 + Cups Gimp Print v4.2.7
I can se the printer in Epson MacAssist for OSX Ver 4.0.aE IP 10.0.0.6
I can se it as well in Safari under the ip adress 10.0.0.6
I have tried to test the printer in the Common Unix Printing System
I can see the printer there as well.
A test print here results in
"ipp" stopped unexpectedly with status 1
All my other printers work well and prints test sheets.
The printer has not worked since Tiger.

Can you please help me....
I can't seem to get the Print Set up utility to find the Epson Stylus 3000 Gimp.
I installed the GimpPrint Drivers that were on the Tiger 10.4.3 install DVD after I installed 10.4.3, and then updated 10.4.3 to 10.4.5.
When I first installed 10.4.3, I didn't install the GimpPrint Drivers. I went back to the DVD after updating to 10.4.5, and then installed the GimpPrint Drivers.
Can you please help me out in what I'm doing wrong. Everytime I try to find the Epson Drivers an "error:-50" comes up in the Printer Browser under IP Printer section.
Here's what I'm doing:
- I go into Printer Setup Utility
- I choose Add Printer
- I choose IP Printer
- I choose Line Printer Daemon - LPD
- I pop up the "Print using" and select the "EPSON".
- Then I choose "EPSON Stylus Color 3000 - Gimp-Print v5.0.0-beta2
- THEN I GET AN ERROR MESSAGE POP-UP! "An error occurrd while trying to add the selected printer. Error:-50"
Where did you find the:
Epson Stylus Color 3000 + Cups Gimp Print v4.2.7
Thank you for you help in advance!
Micdim
G4 Dual 1.42 gig Mac OS X (10.4.5) 1G Ram, FCStudio, Logic Pro 7.1, Adobe CS2, After Effects 7, MSOffice 2004...

Similar Messages

Problem with "Epson Stylus SX110 (or SX115)" and the Airport Express

Hello,
I connect my printer on my airport express, via wifi connection. And the airport express doesn't recognize the printer (via the airport express utility)
When I connect my previous printer (a canon), it works well.
Thanks if you met this pb, to help me

Hi All,
I have intel based macbook pro running OSX 10.6.2, airport express with a connected EPSON Stylus SX115.
I discovered two issues with using the printer via my Airport Express:
1. I had to use the driver called 'Epson Stylus SX 100'. It ships with the op system. (note: NOT the 'Epson SX 100' !!! There is also one called like that, but it does not work for me...). When I tried to use the sx 110 driver, the printing stopped half way. Strange enough the sx 110 driver works ok when the printer is connected via a USB cable
2. Now the more annoying problem.
It takes ages before the airport express discovers the printer!!! After I scanned via an USB cable, I reconnected the printer to the Airport express. Printing was dead. Next I followed the Apple provided troubleshooting (restart sequence, etc). No success, the airport still couldn't find the connected printer, so I was getting really ******…..
The solution I propose, as it worked for me already more than once on my macbook pro, is the following:
1. Connect the printer to the Airport Express, switch the printer on and, and restart AE via the AE utility (Just to make your consciousness rest.):
- Start Airport Utility: you can find the program by typing the name in spotlight
- right click on the on the Icon of your Airport Express on the right of the window
- Issue a restart (It takes some seconds to complete!)
2. WAIT! As annoying it is, it takes about 15-30 min before Airport express discovers the printer.
3. In System Preferences/Print&Fax add the printer: (NOTE: This is an optional step, in case the printer is set up the first time, otherwise skip to step 5. )
- On the right, at the bottom of the Printers sub window, click on the + sign. This opens the Add Printer dialogue
- In the Add Printer dialogue you should be able to see now your Epson printer discovered by Bonjour. Highlight it by clicking on it. (If you don't see your printer, you might have been impatient and waited to little after you connected the printer to the airport express, or you have some problem I did not have…)
- At the bottom open the 'Print Using:' drop-down box, and choose the 'Select Printer' option. This opens a new dialogue. Scroll down to 'Epson Stylus SX 100 - Gutenprint v5.2.3'. Click on it, and press OK. This closes the 'Select Printer' dialogue
- Back at the Add Printer dialogue, change the name of your printer to something more meaningful, to 'Epson SX 115 - Wireless' for example.
- click ad
4. Back at the Print & Fax dialogue, now you should see a new printer icon on the left with the name you just gave, and with an icon that does not look at all like your printer.
5. Congratulations, you are done. You should be able to print now.
I hope it helps

Problem with "Epson Stylus SX115 (SX115 like)" and the Airport Express

Hello,
I connect my printer on my airport express, via wifi connection. And the airport express doesn't recognize the printer (via the airport express utility)
When I connect my previous printer (a canon), it works well.
Thanks if you met this pb, to help me=

Hello,
I connect my printer on my airport express, via wifi connection. And the airport express doesn't recognize the printer (via the airport express utility)
When I connect my previous printer (a canon), it works well.
Thanks if you met this pb, to help me=

Problems with Epson sx105

Hi,
I really tried any possible driver but I am still getting the same error message:
I [16/Dec/2008:11:39:56 +0000] Using policy "default" as the default!
I [16/Dec/2008:11:39:56 +0000] Full reload is required.
I [16/Dec/2008:11:39:56 +0000] Loaded MIME database from '/private/etc/cups': 52 types, 49 filters...
I [16/Dec/2008:11:39:57 +0000] Loading job cache file "/private/var/spool/cups/cache/job.cache"...
I [16/Dec/2008:11:39:58 +0000] Full reload complete.
I [16/Dec/2008:11:39:58 +0000] Cleaning out old temporary files in "/private/var/spool/cups/tmp"...
I [16/Dec/2008:11:40:05 +0000] Listening to :::631 on fd 8...
I [16/Dec/2008:11:40:05 +0000] Listening to 0.0.0.0:631 on fd 9...
I [16/Dec/2008:11:40:05 +0000] Listening to /private/var/run/cupsd on fd 7...
I [16/Dec/2008:11:40:05 +0000] Listening to ::1:631 on fd 4...
I [16/Dec/2008:11:40:05 +0000] Listening to 127.0.0.1:631 on fd 6...
I [16/Dec/2008:11:40:05 +0000] Resuming new connection processing...
I [16/Dec/2008:11:41:48 +0000] [Job ???] Request file type is application/postscript.
I [16/Dec/2008:11:41:48 +0000] [Job 8] Adding start banner page "none".
I [16/Dec/2008:11:41:48 +0000] [Job 8] Adding end banner page "none".
I [16/Dec/2008:11:41:48 +0000] [Job 8] File of type application/postscript queued by "Olaf".
I [16/Dec/2008:11:41:48 +0000] [Job 8] Started filter /usr/libexec/cups/filter/pstoappleps (PID 331)
I [16/Dec/2008:11:41:48 +0000] [Job 8] Started filter /usr/libexec/cups/filter/pstocupsraster (PID 332)
I [16/Dec/2008:11:41:48 +0000] [Job 8] Started filter /Library/Printers/EPSON/InkjetPrinter/Filter/rastertoescp.app/Contents/MacOS/ra stertoescp (PID 333)
I [16/Dec/2008:11:41:48 +0000] [Job 8] Started backend /usr/libexec/cups/backend/smb (PID 334)
W [16/Dec/2008:11:41:48 +0000] [Job 8] recovered:
E [16/Dec/2008:11:41:49 +0000] PID 333 (/Library/Printers/EPSON/InkjetPrinter/Filter/rastertoescp.app/Contents/MacOS/r astertoescp) stopped with status 206!
I [16/Dec/2008:11:41:49 +0000] Hint: Try setting the LogLevel to "debug" to find out more.
E [16/Dec/2008:11:41:51 +0000] [Job 8] Job stopped due to filter errors.
I really need help or I will smash this printer.
Cheers
Olaf

Can you please help me....
I can't seem to get the Print Set up utility to find the Epson Stylus 3000 Gimp.
I installed the GimpPrint Drivers that were on the Tiger 10.4.3 install DVD after I installed 10.4.3, and then updated 10.4.3 to 10.4.5.
When I first installed 10.4.3, I didn't install the GimpPrint Drivers. I went back to the DVD after updating to 10.4.5, and then installed the GimpPrint Drivers.
Can you please help me out in what I'm doing wrong. Everytime I try to find the Epson Drivers an "error:-50" comes up in the Printer Browser under IP Printer section.
Here's what I'm doing:
- I go into Printer Setup Utility
- I choose Add Printer
- I choose IP Printer
- I choose Line Printer Daemon - LPD
- I pop up the "Print using" and select the "EPSON".
- Then I choose "EPSON Stylus Color 3000 - Gimp-Print v5.0.0-beta2
- THEN I GET AN ERROR MESSAGE POP-UP! "An error occurrd while trying to add the selected printer. Error:-50"
Where did you find the:
Epson Stylus Color 3000 + Cups Gimp Print v4.2.7
Thank you for you help in advance!
Micdim
G4 Dual 1.42 gig Mac OS X (10.4.5) 1G Ram, FCStudio, Logic Pro 7.1, Adobe CS2, After Effects 7, MSOffice 2004...

Can I use my MacBook Pro with 10.7.5 with Epson Stylus Printer photo R340

MacBook Pro with 10.7.5 with Epson Stylus Printer photo R340 can I make them work togather?

Try resetting the SMC. The phone connection is only supported for tethering. I know nothing about the other device.
Barry

Printing Problem with EPSON LX 300+

Dear all,
I have met a problem with Epson LX 300+. After I set up printing on PLD, the result printing is bad. Font and setting are not the same as preview in SBO. How to solve this matter..? I used SBO 2005A PL 43.
Thanks for your help....
Regards,
agung
Edited by: Agung Adrianto on Aug 28, 2008 8:17 AM

Hi Agung,
Here is a way out for the issue you have submitted. I can't guarantee that this wayout work perfectly:
Question:
As we know that the dos matrix printer supports dos prompt and thus printing speed and
life of the printing head is comparatively more than what we print the same in graphical format.
So when I tried to print from SAP Bone in dot matrix printer, the printing speed is very slow and quality of printout is not good enough.
Any clarifications on this regard would prove very helpful to me.
Regards,
xxxxx
Consultant Business solutions.
Solution:
Do you use one of this printer types:
Dot Matrix, Printer, Needle Printer, Citizen ProDot 300 , Oki Microline, Epson FX880, Epson FX890 ?
Here the stepwise I have tried :
In order to print using Dot Matrix printers, follow the below
instructions:
1. Run SAP Business One.
2. Click the upper menu 'File' and select 'Page Setup'.
3. The Print Setup window opens. Under 'Paper', in the field 'Size', select 'Letter' from the drop down menu.
4. Click OK to confirm your selection.
5. On your desktop, click Start => Settings => Printers.
6. Right click on the required Dot Matrix printer and select 'Printing Preferences...'.
7. Click the 'Paper/Quality' tab page and click the 'Advanced' pushbutton.
8. Under'Paper/Output'=> 'Paper Size', click on the underlined paper size(e.g. A4) and select 'Letter' from the drop down menu.
Note that if you leave the value 'A4', each page will be spreaded over 2 pages when printing using Dot Matrix printers.
9. Under 'Graphic'=> 'Print Quality', click on the underlined value (e.g. 230X250 dots per inch) and select '120X144 dots per inch' from thedrop down menu.
Note that in case the value '120X144' is not available you should select a similar value from the list.
I did not test it yet and I am not so sure about the result but you could test it.
Rgds,

Using Lightroom for Windows 8.1 with Epson Stylus Photo R3000 printer.

Using Lightroom for Windows 8.1 with Epson Stylus Photo R3000 printer. From PRINT section, if I click either "Page Setup" or "Printer" I get the Epson printer dialog box, drill down, change settings- so far so good. When I'm finished with the settings and close the dialog box (hit OK) the print job starts immediately; I never get a chance to hit the Lightroom "Print" button. Question: does this bypass any Lightroom processing or control of the print job?

Even if I just click the Printer button to verify my settings I should then return to Lightroom, and then click Print to start the job. This does not happen, the job starts as soon as I close the properties dialog box. Again, is any Lightroom processing or control being bypassed because of this?

Printing Problem with Epson R320 (Print CD)

Problem: I cannot print using Print CD with a new Epson Stylus Photo R320, however I can print from applications using the gimp beta driver provided in OS software, via <Print Using> dialogue box.
Power Mac G4 dual 450, running 10.4.6.
After phoning Epson, I downloaded the needed driver from Epson and went through the installation process with an Epson tech. However I cannot seem to access this driver in the print utility. The Printer Setup Utility is forcing me to choose a “gimp” driver. Some discussions on this site suggest choosing just Epson usb—the question is how with the way the dialogue boxes are configured in Printer Setup Utility. The problem seems to be I am unable to access the driver through the <Print Using> menu in the utility. If I select more printers, (after highlighting the R320) this causes the print utility to crash.
I have repaired permissions, reset the printer setup, uninstalled, reinstalled; actually I have done everything I could find to do. The problem seems so simple. I easily created my CD label; now I would just like to print it!! Any ideas from all the pros on this list. Thank you.
Mary Ann
Desktop: G4 450 dual and Powerbook G4 15 Mac OS X (10.4.6) Epson Stylus Photo R320

I have an Epson R320 and have communication problems.You start the job and after about 5 seconds you get a ! in the dock on the printer icon and on opening you see "job stopped".
I am no expert but it seems to me that the program e.g.MYOB accounting fails to pass the data to OSX.
If I de install and reinstall the epson drivers and repair permission it will work ...but then the next day on re-booting we are back to the same state of not working.
I have informed Epson and am waiting for a reply. The epson printer tests and standalone mode works. OSX problem?

Printing problem with Epson photo 2200

I have a Powerbook G4 running the most recent version of OSX. I can no longer print to my Epson Photo 2200. When I try and print the Printer window pops up, and the job automatically stops without printing.
I have tried uninstalling and reinstalling the 2200 driver, I have hooked up a Canon printer to the powerbook (and this printer works fine with the powerbook), I have printed a test sheet on the 2200 (which is done without a connection to the Powerbook and it printed fine). The problem lies in the computer printer connection (I am using USB for the link).
Any help you can provide would be greatly appreciated.

I had a similar problem with a Epson Stylus Photo R800. The printer would not print Word docs or DVD media using the most updated software from Epson. After going through two printers I paid a consultant to come in on a Saturday night who told me that communication errors between Epson printers and current versions of the MacOS are encountered every day in his business. And neither Apple or Epson address the issue directly.
To get the Stylus Photo R800 to work we had to reconfigure the driver to deal with Manual Feeding of documents and DVDs. It took about an hour of experimentation but once done...with no help from Apple or Epson...the printer did work very well. However, the Epson Print CD software is a total bust. We found a third party solution called DiscLabel that allowed us to print DVDs with the reconfigured driver. I'm disgusted with both Apple and Epson because Epson sells printer with the promise that it will work with the MacOS when three hours of struggle with useless software proved otherwise.
If others have a better experience or know of simple solutions to the Epson Print CD problem please post them.
Thanks in advance for tolerating my rant.
Powerbook 167 GHz PowerPC G4 Mac OS X (10.4.6)

Upgraded to Mountain Lion and CS3, I am no longer able to access the correct dialog box for fine printing with Epson Stylus Photo 1400.

I have recently upgraded my Mac OS to Mountain Lion, and am using Photoshop CS3 together with Lightroom 5. To my absolute horror, in either Adobe program I am no longer able to access the dialog box which allows me to choose paper type, size, and print quality when attempting to print on my Epson Stylus Photo 1400. An excruciating hour on the phone with largely unintelligible folks at Epson seemed to prove the problem lies with Adobe instead of Epson. I'd greatly appreciate whatever advice might be forthcoming from the Community.

Well, this seemed to work.. can't believe it! After a year of messing with this!
from Stevejones5
"I found a way around this problem. GO to HD/Library/Printers/Epson/InkjetPrinter/ICCProfiles and you will find a file labeled Pro38.profiles. This is a package file. Control click on it and reveal contents. Then you can copy all the profiles and paste them into your Colorsync folder either in the HD/Library folder or your own Home folder/Library. Then the profiles will show up in Photoshop and Lightroom."
Key, is to Control click on the printer to "Open contents". Then open Resource folder. Copy everything in it and then paste it into the "Colorsync" folder in your Library. (Remember, to get to Library you have to hold the command key down for it to appear in "Go" Menu for Finder.
Then I reinstalled printer driver from Apple, then rebooted computer, then plugged in printer. And VOILA-- I can now select Epson Premium Photo Paper Luster!

Photoshop CS3 with Epson Stylus Photo 1400 and Mac Leopard

I have Adobe Photoshop CS3 and an Epson Stylus PHOTO 1400 printer and Mac OS X 10.5.4.
When I print a photo it comes out with excessive ink which smears very easily and has lines in it. It only does it in Photoshop. When I print from any other program it comes out fine. I've seen reviews online where people have printed from Macs and photoshop onto the printer and it worked. I've already contacted Epson, but they said to contact Adobe. Does anybody have any advice?

Forget Epson's useless tech support.
What you describe is typical of improper printer profile or usage of non-Epson paper, especially paper with gloss. Have you profiled the printer/paper and are you using Epson paper (or other paper and profiles specifically recommended here for Epson photo-quality printers) properly selected?
Like Ramón I am on 10.4.11, not 10.5.x, but I doubt if your described problem is due to the OS version.

How can I fix my MacBook Pro losing wireless connectivity with Epson Stylus NX625 printer. It will work once and then I get an error saying the printer is not connected.

I can connect to my Epson Stylus NX625 through my wireless network and print a page or two, but then the next time I go to print it says that the printer is not connected. Any fixes? I have tried deleting the printer and re-adding it to my MacBook Pro OS X version 10.9.4, but sometimes it doesn't even find it, and other times it says it is connected, but when I go to print it says not connected. Very frustrated. I have also installed the latest drivers, etc.
What now?

Your computer is going to run hot while playing CPU/GPU intensive games - it should heat up and the fans should be noticably loud. As to why it's 'crashing' - can you post a kernel panic log? You may have some third-party kexts that are causing the problems.
Clinton

Can't scan with Epson Stylus DX4450

Hi everybody.
I'm trying to configure my Epson Stylus DX4450. Printing works like a charm, but scanner is not. I tried to configure it as it was suggested on various websites. I've installed sane, xsane, iscan (from http://repo.archlinux.fr/i686) also I've downloaded iscan-plugin-cx4400 from Avasys website, extracted it with rpmextract ant put the library to /usr/lib/iscan.
When I try sane-find-scanner it shows:
# sane-find-scanner will now attempt to detect your scanner. If the
# result is different from what you expected, first make sure your
# scanner is powered up and properly connected to your computer.
# No SCSI scanners found. If you expected something different, make sure that
# you have loaded a kernel SCSI driver for your SCSI adapter.
found USB scanner (vendor=0x04b8 [Language Error], product=0x083f [Language Error]) at libusb:002:010
# Your USB scanner was (probably) detected. It may or may not be supported by
# SANE. Try scanimage -L and read the backend's manpage.
# Not checking for parallel port scanners.
# Most Scanners connected to the parallel port or other proprietary ports
# can't be detected by this program.
# You may want to run this program as root to find all devices. Once you
# found the scanner devices, be sure to adjust access permissions as
# necessary.
When I try scanimage -L it's idle for about a minute and then it shows:
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
But when I try it again it shows:
device `epkowa:libusb:002:010' is a Epson flatbed scanner
Then if I try sane-find-scanner again it will show no language errors:
found USB scanner (vendor=0x04b8, product=0x083f) at libusb:002:010
xsane will check for available devices for some time, then it shows a message, that no device is available. iscan shows a message "Could not send command to scanner. Check the scanners status". Sometimes iscan will launch, but I can't scan, because it will show me the "Could not send..." error message.
Device usually turns off when I try xsane. Two times xsane launched, but Epson turned off right after it. It also turns off sometimes when I try sane-find-scanner second time or when I try to launch iscan.
I read that there can be a conflict between sane and gphoto, moved /etc/udev/rules/54-gphoto.rules and restarted udev - still didn't work.
/etc/sane.d/dll.conf:
# enable the next line if you want to allow access through the network:
net
abaton
agfafocus
apple
avision
artec
artec_eplus48u
as6e
bh
canon
canon630u
#canon_pp
cardscan
coolscan
coolscan2
#dc25
#dc210
#dc240
dell1600n_net
dmc
epjitsu
#epson
#epson2
epkowa
fujitsu
#gphoto2
genesys
gt68xx
hp
hp3900
hpsj5s
hp3500
hp4200
hp5400
hp5590
hpljm1005
hs2p
ibm
leo
lexmark
ma1509
matsushita
microtek
microtek2
mustek
#mustek_pp
mustek_usb
mustek_usb2
nec
niash
pie
pint
pixma
plustek
#plustek_pp
#pnm
qcam
ricoh
s9036
sceptre
sharp
sm3600
sm3840
snapscan
sp15c
#st400
#stv680
tamarack
teco1
teco2
teco3
#test
u12
umax
#umax_pp
umax1220u
v4l
# The following backends are not included in the sane-backends distribution
# If you want to use them, download them from their webpages and read their
# documentation
# HP OfficeJet backend homepage: http://hpoj.sf.net/
# Uncomment the following line if hpoj is installed:
#hpoj
hp_rts88xx
#hpaio
/etc/sane.d/epkowa.conf:
# epkowa.conf -- sample configuration for the EPKOWA SANE backend
# Copyright (C) 2004 Olaf Meeuwissen
# See sane-epkowa(5), sane-scsi(5) and sane-usb(5) for details.
# SCSI scanners can be configured simply by listing the path to the
# device. For example, if your system claims to have a /dev/scanner
# SCSI device, all you have to do is uncomment the following line:
#/dev/scanner
# In the interest of maintainability, most installations would have
# /dev/scanner sym-linked to the real SCSI scanner device node.
# An alternative way that works for many operating systems and is a
# little bit more generic, is to have the backend probe for your SCSI
# scanner with the following configuration command:
#scsi EPSON
# On systems with libusb, the following line is sufficient to get the
# backend to recognise your USB scanners. It presumes, however, that
# the scanner---more precisely, it's USB product ID---is known to the
# backend.
# For all USB scanners that are officially supported by this backend,
# this presumption is true. A list of such scanners can be found in
# sane-epkowa(5).
usb 0x4b8 0x83f
# For any USB scanner not known to the backend (yet), you may, at your
# own peril(!!), force the backend to recognise and use it via libusb.
# You can do so by the following configuration command:
# usb <USB vendor ID> <USB product ID>
# SEIKO EPSON's USB vendor ID is '0x04b8' (without quotes). In order
# to find the USB product ID, use lsusb(1) or, on Linux systems, peek
# at the information in /proc/bus/usb/devices.
# A sample configuration for the Perfection 1650 (GT-8200), which has
# a product ID of 0x0110, would look as follows:
#usb 0x04b8 0x0110
# When not accessing your USB scanner via libusb, you may need to use
# one of the configuration commands below or commands that are almost
# the same. These commands typically access the scanner via a kernel
# scanner module.
usb /dev/usb/scanner0
usb /dev/usbscanner0
usb /dev/uscanner0
# Linux had a scanner module until version 2.6.2. As of version 2.6.3
# libusb is your only option. Linux' scanner module can be loaded via
# the modprobe(8) command like so:
# modprobe scanner vendor=<USB vendor ID> product=<USB product ID>
# If the scanner module already knows the vendor and product IDs, you
# do not have to specify them. If you want to have this done automa-
# tically every time you boot, you can add the above line, except for
# the modprobe command itself, to your /etc/modules file.
# Although not tested with this backend, parallel port scanners should
# be usable. You can configure them as shown below, but I do not know
# much about the details. Information is welcome.
#pio 0x278
#pio 0x378
#pio 0x3BC
/etc/udev/rules.d/53-sane.rules (shortened):
# This file was automatically created based on description files (*.desc)
# by sane-desc 3.3 from sane-backends 1.0.19 on Fri Mar 7 06:29:43 2008
# udev rules file for supported USB devices
# To add a USB device, add a rule to the list below between the
# LABEL="libsane_rules_begin" and LABEL="libsane_rules_end" lines.
# To run a script when your device is plugged in, add RUN+="/path/to/script"
# to the appropriate rule.
# The following list already contains a lot of scanners. If your scanner
# isn't mentioned there, add it as explained above and mail the entry to
# the sane-devel mailing list ([email protected]).
ACTION!="add", GOTO="libsane_rules_end"
ENV{DEVTYPE}=="usb_device", GOTO="libsane_create_usb_dev"
SUBSYSTEM=="usb_device", GOTO="libsane_rules_begin"
SUBSYSTEM!="usb_device", GOTO="libsane_rules_end"
# Kernel >= 2.6.22 jumps here
LABEL="libsane_create_usb_dev"
# For Linux >= 2.6.22 without CONFIG_USB_DEVICE_CLASS=y
# If the following rule does not exist on your system yet, uncomment it
# ENV{DEVTYPE}=="usb_device", NAME="bus/usb/$env{BUSNUM}/$env{DEVNUM}", MODE="0664", OWNER="root", GROUP="root"
# Kernel < 2.6.22 jumps here
LABEL="libsane_rules_begin"
# EPSON Stylus CX4300 | EPSON Stylus CX4400 | EPSON Stylus CX5500
# EPSON Stylus CX5600 | EPSON Stylus DX4400 | Epson Stylus DX4450
ATTRS{idVendor}=="04b8", ATTRS{idProduct}=="083f", MODE="0664", GROUP="scanner", ENV{libsane_matched}="yes"
# The following rule will disable USB autosuspend for the device
ENV{libsane_matched}=="yes", RUN+="/bin/sh -c 'test -e /sys/$env{DEVPATH}/power/level && echo on > /sys/$env{DEVPATH}/power/level'"
LABEL="libsane_rules_end"
Can anyone help with this?

Almost solved.
First I've copied files extracted from iscan-plugin-cx4400.rpm from /usr/lib/iscan to /usr/lib/sane. Didn't work.
Then I've checked version of iscan with yaourt and it appeared that aur have newer version than the one from archlinux.fr repo. I've built it, moved epkowa.conf.pacsave to epkowa.conf and it worked once.
sane-find-scanner output was the same, with language errors, but scanimage -L showed that it found my scanner (don't have the exact output - it was different than before). xsane still didn't found the device but I managed to preview and scan to file printer test page with iscan.
When I tried it for the second time, sane-find-scanner output was the same, but scanimage -L didn't recognised the scanner. iscan didn't work. Tried to restart the device - still the same.
Tried to turn off the scanner, restart udev, start scanner again. Didn't work.

Printing problem with Epson R290

I am running CS2 on Leopard and have recently purchased an Epson R290. The first time I used it with Illustrator and InDesign it worked fine but now whenever I print anything it prints a tiny version (about a sixth of the real size) of the design in the top left corner of the page. It does this both with new documents and old ones that used to print ok.

Since I posted the message about this problem I have discovered that it can be worked around by choosing a higher quality print. ie if you choose plain paper when printing from Illustrator or InDesign the printer prints a reduced size image but if you choose Ink jet mat or glossy the print comes out fine. I don't have this problem with Photoshop but that may be that I always print high quality from that application. I don't use Appleworks Draw so don't know whether this solves the problem for that application but iWork documents print ok.

Printing problem with Epson R290 Illustrator and inDesign

I am running CS2 on Leopard and have recently purchased an Epson R290. The first time I used it with Illustrator and InDesign it worked fine but now whenever I print anything it prints a tiny version (about a sixth of the real size) of the design in the top left corner of the page. It does this both with new documents and old ones that used to print ok.

Since I posted the message about this problem I have discovered that it can be worked around by choosing a higher quality print. ie if you choose plain paper when printing from Illustrator or InDesign the printer prints a reduced size image but if you choose Ink jet mat or glossy the print comes out fine. I don't have this problem with Photoshop but that may be that I always print high quality from that application. I don't use Appleworks Draw so don't know whether this solves the problem for that application but iWork documents print ok.

Problems with Epson Stylus 3000 IP Ethernet

Similar Messages

Maybe you are looking for