Problems with RPM fans [SOLVED]

Question

Hello. I'm a Spanish user. I don't speak very well English, I'm sorry.
My problem: PWMconfig don't detect modules:
$ pwmconfig
# pwmconfig revision 5630 (2009-01-29)
This program will search your sensors for pulse width modulation (pwm)
controls, and test each one to see if it controls a fan on
your motherboard. Note that many motherboards do not have pwm
circuitry installed, even if your sensor chip supports pwm.
We will attempt to briefly stop each fan using the pwm controls.
The program will attempt to restore each fan to full speed
after testing. However, it is ** very important ** that you
physically verify that the fans have been to full speed
after the program has completed.
/usr/sbin/pwmconfig: There are no pwm-capable sensor modules installed
This is my lm_sensors:
# Generated by sensors-detect on Wed Apr 22 22:22:34 2009
# This file is sourced by /etc/rc.d/lm_sensors and defines the modules to
# be loaded/unloaded.
# The format of this file is a shell script that simply defines variables:
# HWMON_MODULES for hardware monitoring driver modules, and optionally
# BUS_MODULES for any required bus driver module (for example for I2C or SPI).
HWMON_MODULES="adt7473 coretemp w83627ehf"
# For compatibility reasons, modules are also listed individually as variables
# MODULE_0, MODULE_1, MODULE_2, etc.
# You should use BUS_MODULES and HWMON_MODULES instead if possible.
MODULE_0=adt7473
MODULE_1=coretemp
MODULE_2=w83627ehf
Sensors:
$ sensors
coretemp-isa-0000
Adapter: ISA adapter
Core 0: +42.0°C (high = +82.0°C, crit = +100.0°C)
coretemp-isa-0001
Adapter: ISA adapter
Core 1: +37.0°C (high = +82.0°C, crit = +100.0°C)
coretemp-isa-0002
Adapter: ISA adapter
Core 2: +34.0°C (high = +82.0°C, crit = +100.0°C)
coretemp-isa-0003
Adapter: ISA adapter
Core 3: +33.0°C (high = +82.0°C, crit = +100.0°C)
Here, in Spain, I don't get any answer:P. I think in this forum you can solve my problem.
Thanks!!!
Last edited by analca3 (2009-05-04 18:00:02)

Answer 1

Mmm... I just tried this, but it's the same. My motherboard is "ASUS P5Q-E". In Windows Vista Ultimate 64 bits I can do this with SpeedFan.
My rc.conf is this:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="es_ES.utf8"
HARDWARECLOCK="local"
USEDIRECTISA="no"
TIMEZONE="Europe/Madrid"
KEYMAP="es"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=(sensors fuse adt7473 coretemp w83627ehf)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="..."
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth1="eth0 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.196"
eth1="dhcp"
INTERFACES=(eth1)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng @network netfs crond alsa gdm gpm dbus hal cups sensors)
What can I do?
Thank you very much!!