Problems with spontaneous reboots with K7t266 Pro-RU

I have been having problems with this board for about six months. I recently installed the same board into another system and still have the same issues.
The system powers-on spontaneously after shutdown. I have checked that there are no "wake on LAN settings" enabled in the BIOS. The same problem occurred in two different systems with the same board. It happens anytime overnight.
I am running Windows and Office XP with current Service Packs
AMI BIOS A6380MS V1.8 010202
Most recently I installed the board in a new case and re-installed windows XP from scratch.  The stand by  button is grayed out when I select Windows turn off computer. When I shutdown the computer it simply restarts and does not shutdown properly.
I purchased the motherboard in September 2001. I tried running the RAID array with two IBM Deskstar model IC35L040AVVA07-0,  40 GB hardrives. The RAID array would fail after a few weeks to a few months of use. I damaged both drives while trying to recover from these failures and could not repair the drives even with a low-level format. I finally gave up and stopped using the RAID.
I have not upgraded the bios on the Promise RAID chip.
Has anyone else had so  much problems with this board?

Quote
Originally posted by Bas
Hi,
Make sure you have IPCA turned on.
APM turn it on.
Turn USB Wakeup off
Turn Restore on AC/Powerloss off
Turn WakeUp on Ring off
Turn WakeUp on PME off
Turn Resume by Alarm off
That should do the trick...
Thanks for that. I had all these settings as described above but was still getting the spontaneous reboots. Actually I have narrowed it down to it occuring only when I have another PC on my LAN, but Wake up on LAN is definitely disabled.

Similar Messages

  • USB problem with K7T266-Pro

    I have an USB problem with Logitech Cordless Wingman Gamepad. I have dowloaded the newest version of logitech gamepad, and the VIA drivers for motherboard K7T266-pro. I also tried to install the USB filter rc1, but the problem remains.
    Here is how the problem occur:
    1. On start up, the gamepad is detected and ready to use.
    2. While I am playing a game, the usb device is reconnecting a lot. I turned of the "Allow this device to turn off to save power" in device manager under all USB root hub. But the problem remains.
    3. After a while, when I have been playing for a while, the gamepad turns off, and the usb device is not recognized error message appears. Under device manager I now have a Unknown Device under USB.
    4. To get it function again I have to restart the computer.
    Anybody who knows the answer for this ?  

    I have a similar problem but with my Logitech optical mouse.  It's also using the usb port and it keeps disconnecting and reconnecting the device in Win XP.  I use to have Win2000 and I experienced the problem but not as often as now.  Also in Win2000 there wasn't an annoying sound when a device would connect and reconnect, and not to mention when your playing a game and the mouse quits for 1/2 a second, really annoying!  Sometimes it will quit completely and I have to either physically reconnect it or reboot to get it working again.  
    I have recently tried fixing the problem:
    a) I flashed my old Bios and put in ver 1.9 from this site
    b) I've updated the Via 4in1 drivers
    c) I've updated the mouse drivers that come from Logitech.
    None of these updates helped.  I've taken my mouse to work to see if it does the same thing, but so far so good.  My pc at work is running Win2000 but different MB.  I don't think there is anything wrong with the mouse.  Although I haven't tried using the PS/2 adapter  that came with it and see if it behaves the same way.  I have a feeling the mouse will work fine, but kinda sucks cause I have usb and I have to revert back to PS/2 just so it works properly.
    I've read on the Via Hardware forum some people having the same problem but with an Abit board.  They changed something in their Bios to resolve it.  If anyone has any ideas, maybe changing something in the Bios that has to do with the usb ports, I would greatly appreciate it.

  • Problem with K7T266 pro, usb not working corectly!

    Have a problem here.
    My MOMO racing wheel (USB) stops responding while playing games, but the wheel works fine on my friends comp. When i start a geme, i can play it for 30-60mins, and then it just stops responding, the lights on the wheel dont glow and it seems disconnected, my only help then is to restart my comp.
    And my specs are:
    MSI K7T266 pro
    AMD athlon 1,4Ghz
    Win98SE
    I use the usb ports, that are in my mainboard.
    Please answer if you know about the problem, or if you have expirianced something like that.

    After killing my K7N2G-ILSR, ive had to revert to my backup K7T266 ProR system. While playing UT2K3 I had those freaking random disconnects of the USB which would kill the FPS and get me fragged, after which time it would happily reconnect and work fine. My optical mouse would also disconnect like that.
    I am running XP Home, VIA 4.43. I set the BIOS to read only USB1 (which didnt work). Then I installed the VIA USB filter RC-1 and havent had a disconnect problem for over 24 hours now. Get the usb filter from MSI website and good luck!

  • Hello  I have a problem with Mac Pro, iPhoto does not want to stay open and close as I can figure this out?  thanks

    Hello  I have a problem with Mac Pro, iPhoto does not want to stay open and close as I can figure this out?  thanks

    Refer below link once
    App doesn’t open | Progress wheel spins continually

  • Does anyone still have problems with Premier Pro on Maverick? and is there any known fix?

    Does anyone still have problems with Premier Pro on Maverick? and is there any known fix?

    I know OSX 10.9 Mavericks introduced a power saving feature called App Nap which is meant to slow down applications that it determins are inactive (or when minimized). This would mostly likely cause problems if you're dynamically linking After Effects comps to your timeline or sometimes exporting to Media Encoder.
    Try disabling App Nap for all your Adobe App files...
    Go to your Applications folder
    Go into individual Adobe app folders (ie. Adobe Premiere Pro CC)
    Right-click on the Adobe app file (ie. Adobe Premiere Pro CC.app) and select Get Info
    When the info window opens up, add a checkmark beside "Prevent App Nap"
    Restart the application
    This fixed all my performance issues.
    -Pete

  • HI, I just bought Photoshop CS5 and I have a problem with HDR pro

    HI, I just bought Photoshop CS5 and I have a problem with HDR pro . when I am trying to mount 3 images together it act in a strange way ( the images appear and disappear many times) then when the window with the result appear and I say ok it open up in photoshop as a single image ( in the layers there is just 1 photo) and when I am trying to work it up with the Plug in/filter HDR Effex Pro (Nik softwear) a pop up window appear saying that the file is missing and the operation it is not possible. Why and what is happening ? Someone can help me ?

    This is normal operation. The output from HDR pro does not produce a layered file. You make all your adjustments in the Nik Plug-in. Once Nik has finished you then make any rinal changes in Photoshop. Trying to use NIK again on the image in Photoshop is not the way to do this.
    When HDR pro comes up do you see all the presets and controls? Presets on the left and controls on the right
    MK

  • I have a problem with macbook pro OS 10.5.8 and cannot play youtube anymore, before Yes

    i have a problem with macbook pro mac os 10.5.8 and cannot play youtube but before ther is no problem abou this. now there is warning sign to install adobe flash player, but when i install adobe it said cannot be compatible, and I went to the apple store, they sid need to upgrade the system to mac IOS 10.6 and i dont want to spend much... somebody to help me this

    Upgrading to Snow Leopard
    You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
    After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mavericks if your computer meets the requirements.
         Snow Leopard General Requirements
           1. Mac computer with an Intel processor
           2. 1GB of memory
           3. 5GB of available disk space
           4. DVD drive for installation
           5. Some features require a compatible Internet service provider;
               fees may apply.
           6. Some features require Apple’s iCloud services; fees and
               terms apply.
    Upgrading from Snow Leopard to Lion or Mavericks
    To upgrade to Mavericks you must have Snow Leopard 10.6.8, Lion, or Mountain Lion installed. Purchase and download Mavericks (Free) from the App Store. Sign in using your Apple ID. The file is quite large, over 5 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
         OS X Mavericks- System Requirements
           Macs that can be upgraded to OS X Mavericks
             1. iMac (Mid 2007 or newer) — Model Identifier 7,1 or later
             2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) —
                 Model Identifier 5,1 or later
             3. MacBook Pro (Mid/Late 2007 or newer) — Model Identifier 3,1 or later
             4. MacBook Air (Late 2008 or newer) — Model Identifier 2,1 or later
             5. Mac mini (Early 2009 or newer) — Model Identifier 3,1 or later
             6. Mac Pro (Early 2008 or newer) — Model Identifier 3,1 or later
             7. Xserve (Early 2009) — Model Identifier 3,1 or later
    To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
    Are my applications compatible?
             See App Compatibility Table — RoaringApps.
    Upgrading to Lion
    If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
    You can purchase Lion at the Online Apple Store. The cost is $19.99 (as it was before) plus tax.  It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
         Lion System Requirements
           1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
               or Xeon processor
           2. 2GB of memory
           3. OS X v10.6.6 or later (v10.6.8 recommended)
           4. 7GB of available space
           5. Some features require an Apple ID; terms apply.
    This, Adobe Flash Player 12.0.0.70, is the current version of Flash. It should work with Snow Leopard or later.

  • We have 'CS6' version of Adobe. We are facing a problem with 'Acrobat Pro'. Every month that is stop working and everytime need to install. Kindly help us regarding solving this problem...

    We have 'CS6' version of Adobe. We are facing a problem with 'Acrobat Pro'. Every month that is stop working and everytime need to install. Kindly help us regarding solving this problem...

    Your Acrobat is running in Trial Mode.  Try this KB: Creative Cloud applications unexpectedly revert to trial mode | CS6, CCM
    If it doesn't work you need to contact Adobe Support for assistance.

  • Having problem with MacBook Pro launching mission control without prompting

    Having problem with MacBook Pro, launching mission control without prompting. Please advise. Thank you.

    It may be a swipe that's doing this >  Mac Basics: Mission Control

  • I have 64 bit windows 7 and CS4 Production Premium. I have a problem with Premiere Pro CS4, it keeps

    I have 64 bit windows 7 and CS4 Production Premium. I have a problem with Premiere Pro CS4, it keeps freezing and Crashing. A simple thing like leaving the project idle for about 15 minutes, you come back and find that it has frozen. Also if you drag out a clip on the timeline you will find that the whole application freezes. Any possible solutions would be much appreciated.

    Could be several factors at play here. This ARTICLE might give you some tips on getting your computer ready for an editing session. Note that there are some added tips on Win7, thanks to Black Viper, near the end.
    If nothing is helping, then the tips in this ARTICLE might help you find some clues amongst the breadcrumbs left behind with a hang, or crash.
    The link in this ARTICLE will give you some general troubleshooting tips.
    If nothing improves, then please post back with more details. This ARTICLE will give you tips on what would be helpful.
    Good luck,
    Hunt

  • Problem with Logic Pro and Soft eLicenser on Mountain Lion?

    Hi!
    I have a bunch of Arturia synths, which requires the Soft eLicenser to work. This has always worked great with Lion, never any problems with eLicenser (never had to open it etc.)
    Now - I upgraded to Mountain Lion, and tested my synths to make sure everything was OK, experienced a bunch of problems, and did a full recovery to clean Mountain Lion.
    After installing the Arturia synths, and adding my licenses, I installed Logic. Everything worked fine!
    BUT!
    When I closed an Arturia synth within Logic, or closed Logic after running a project with one of these synths, I couldn't reopen any of these synths within Logic afterwards - In fact, I couldn't open the stand-alones either! And when I tried to open the eLicenser Control Center, it would just say "Reading eLicensers" forever. After a reboot, everything is OK.
    I can open and close eLicenser Control Center and standalone synths as many times as I want, as long as I don't open Logic, and then Arturia synths as an AU in Logic.
    I found a workaround: Open the eLicenser Control Center, and let in run in the background (cmd+H), and then open Logic. Then I could open Arturia synths and close them, close Logic and reopen etc. without any problems at all. NO PROBLEMS.
    Until I close the eLicenser Control Center, then I have to reboot to be able to start it again.
    I hope you understand what I mean here. It's a bit hard to explain.
    In short terms: Logic makes Soft eLicenser crash when a eLicenser synth has been opened as an AU.
    The same problem is when scanning the AU with AU manager. eLicenser window should be open before scanning.
    Does ANYBODY have the same problems? Can anyone who has these applications test it out?

    So it definitely seems to be a issue with Logic.
    I can't force this error in 10.7.X no matter how hard I try, but in 10.8.2 it's definitely Logic messing things up.
    Could it be auvaltool which has a bug? Or is that only run with AU manager on validation?
    Hopefully this discussion can get some attention, and maybe it could be corrected. I guess a lot of Logic Pro users also has eLicenser Control Center for validation of their products.

  • IMessage and USB problems with MacBook Pro (Maverick)?

    Since I updated my MacBook Pro (2011) to Maverick I have had problems with imessage not working. I also can't use my USB ports for my printer, card reader or external disk. USB ports work together with my iPad and iPhone. Does anybody out there have an idea about what I can do to fix these things? Many thanks in advance.

    Please read this whole message before doing anything.
    This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
    Step 1
    The purpose of this step is to determine whether the problem is localized to your user account.
    Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
    While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
    Test while logged in as Guest. Same problem?
    After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
    *Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
    Step 2
    The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
    Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you boot, and again when you log in.
    Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
    Safe mode is much slower to boot and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal boot may also be somewhat slow.
    The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
    Test while in safe mode. Same problem?
    After testing, reboot as usual (not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

  • Problems with officejet pro 8100 and Lion?

    I just bought a new HP Officejet Pro 8100 Wireless and I have not been able to get it to work correctly.  It's hooked up and all the software seems to work but it prints very, very slowly.  It takes about 2 minutes to print a color page.  Is there some known problem with OJPRO8100s and Macs with OS X Lion on them?  I downloaded v12.14.0 of the printer package from HP, uninstalled what came with the printer, and installed the latest and greatest.  Didn't make a bit of difference.

    Officejet Pro 8500a extremely slow printing with Lion Mac OSX 10.7
    http://h30434.www3.hp.com/t5/Printer-All-in-One-Install-Setup/Officejet-Pro-8500 a-extremely-slow-printing-with-Lion-Mac-OSX-10/td-p/1030521

  • SSD-problem with MacBook Pro 13" (Early 2011)

    Hi there,
    I've tried to use two different SSDs in my MacBook Pro 13" (early 2011). The first one (Samsung 840 Series, 500GB) crashed after two days: the beachball appeared and after a restart there was this question mark-symbol on my screen: no system found. Had to send this SSD back to Amazon. A few days later I've bought a new one, a SanDisk Extreme with 450GB. I've used it for two days, then my system crashed again and after a restart of my Mac I couldn't get any further than to the grey apple-symbol. Even the recovery partition didn't work anymore. Does anyone of you have the same problem with his (or her) MacBook Pro 13" (early 2011) - and any ideas for a solution?
    Thanks for your answers!
    Torsten

    can you confirm if this is ok to buy:
    http://www.ebay.ca/itm/New-HDD-Hard-Drvie-Cable-for-13-MacBook-Pro-A1278-MD101-M D102-821-1480-A-2012-/181269577616?pt=LH_DefaultDomain_0&hash=item2a34823f90&_u h b=1
    or
    http://www.ebay.ca/itm/NEW-MacBook-Pro-Unibody-13-A1278-2012-md101-102-HDD-Hard- Drvie-Cable-821-1480-A-/121183868039?pt=LH_DefaultDomain_0&hash=item1c371f1487& _ uhb=1
    or this one..??
    http://www.ebay.ca/itm/for-APPLE-MacBook-Pro-13-A1278-HDD-Hard-Drvie-Cable-MD101 -MD102-821-1480-A-2012-/331060187298?pt=LH_DefaultDomain_0&hash=item4d14b990a2& _ uhb=1
    i guess i aint gotta buy those brackets again..?
    Thanks
    Anjillan

  • Printer problems with Officejet Pro 8500 A910

    Dear all,
    I have been given as a present an Officejet Pro 8500 A910 (serie number CN16LDM020 and product number CM756A). The people whom I have got it from already had some problems with the printer heads. I have accepted the printer, because I want to have it working again. I do encounter some problems however. I hope you kind people on the forum can help me out and get this thing working again. As a side note: I am only interested in using the scanner, printer (only black and white - I do not print in colour) and e-printing (I understand that it is possible to email documents to printer, so that they are printed whilst you are somewhere else). 
    Upon installation I have conneted the internet to my wi-fi. Upon installation it made some test prints, whereby the black dots were good, but the cyan and other colours were not. When I now turn off the installed printer and switch it on again it takes the printer about 5 - 7 minutes to initialize. On the touch screen of the printer it is said "Checking printer, this might take 5 minutes", "Checking printheads", "Aligning printheads" and alike notifications. After 5 - 7 minutes the printer gives the following notification: " Failure notice. Alignment failed. Refer to device documentation for details." When I then push the question mark on the touch screen the following notidication is given: " Alignment failed. Check printer quality of the current print job. If it is not satisfactory, try aligning the printer to see if that improves the quality. To align the printhead again, touch (home), touch (arrow right), touch Tools, and then touch Align Printhead." When I follow these instructions, the same thing happens. I have tried the option "Clean printheads" under "Tools". The test prints that come out are again good in black and white and not good in colour. 
    The ink level of the cartridges is very low for Yellow, Magenta and Cyan. For Black the printer gives a question mark. The expiry date of the cartridges is in 2015. The information on the Self Test Diagnostic Page (you get when you print a report from checking the ink cartridges) gives the following status:
    Printhead status
    Printhead health: Good (for both Black/Yellow and Magenta/Cyan)
    Serial: 7735960 (Black/Yellow) and 7744345 (Magenta/Cyan)
    End of warranty: mid-2013
    Accumulated ink usage (ml): Black 99/Yellow 71, Magenta 57/Cyan 58
    Refilled supply:
    Detected in printhead/printer? For all cartidges "yes".
    When I try to print a document from Word on my MacBook (which runs on Mac OS X 10.6.8) and the printer is on stand-by, Word recognizes the printer, starts with the print order but then comes with the notifications "Printer offline" and "Cannot find printer" and postpones the print order. Today I reset the printer and the print job that I had before the reset (which was postponed) came out. 
    Today, I printed a document whilst the printer was not on stand-by (the touch screen was on home menu) and the print was well (it was only black and white). After the print, the printer also made a print report. Again, the colour was bad, but black ink was good. After that print report, the printer started aligning again. After 5 minutes it gave the above-mentioned failure notice (" Failure notice. Alignment failed. Refer to device documentation for details."). 
    I would assume that the first thing that I should do is get new cartridges. However, since I only print black and white, can't I just buy the Black Ink and disable the other cartridges? Then, I am thinking of not buying HP cartridges (since the warranty term is already over). What cartridges do you reccomend (price-quality)? If  new cartridges are installed (previous owner had same problems with full cartridges) and the problems (with print heads) are not solved, what should I do? 
    On a second note, I want to use the option of printing online. In other words, give a print order on my Iphone to the printer so that it starts printing at home. How do I set this up? How can I test this?
    I would be very obliged with your feedback on the above. 
    Kind regards,
    Onno

    Hey Onno,
    I see you have several items listed about your Officejet Pro 8500a (A910 series) printer.  The main issue that stands out is the print quality issue.  I would advise starting here with your printer.  
    From your information I can see that refill or remanufacture cartridges have been used in this printer at some point.  It is possible that the ink from these cartridges have damaged the internal ink system of the printer.  If you have performed all the troubleshooting steps for the print quality issue you are experiencing, then the next step is going to be replacing the printheads of the unit.
    Troubleshooting Print Quality Issues
    The 8500a requires all cartridges be available even if you are simply printing in B&W.  If the cartridges are low, then you will have to replace the cartridges as needed.  Typically by the design of this printer, however, print quality issues do not follow ink levels in the cartridges as ink is piped to the internal printheads, thus even with empty cartridges there is some ink remaining in the system.
    The printheads for the 8500a can be found at most HP certified retailers if you decide to attempt replacing them as a step towards resolving the issue.  As to the cartridges, I would advise using genuine HP cartridges as HP ink is designed with HP printers in mind.  For information about refilled/remanufactured cartridges please click here.
    Hope this helps in getting the print quality issue alleviated,
    Jason
    -------------How do I give Kudos? | How do I mark a post as Solved? --------------------------------------------------------
    I am not an HP employee.

Maybe you are looking for