Program for debugging webpage

Hey all, my webpage takes forever to load, whenever i edit
this certain file it always puts a bug in the page, something about
CSS code which i never put in there in the first place, but after
all it makes my page take forever to load, so i am wondering if any
of you could tell me what program to use to scan it, i have mac OS
X. Thanks!

quote:
Originally posted by:
bregent
You didn't delete it - it is still in the page. Maybe you
forgot to upload it?
I can't find that file within my website. I just went through
it 3 times and did some searches for it but I can't locate it
within the 258 files that are there. Any ideas of how to find it? I
am also going to tackle the main page too but I'm just learning and
it's one step at a time.

Similar Messages

Steps for debugging the ABAP program

Hi
Im a SAP-BW Consultant. I have a program in R/3-Side. I want to debugg that program.
Please give me the steps for debugging that program .
Kumar

Hi Ravi,
Check this link
http://help.sap.com/saphelp_nw2004s/helpdata/en/b3/d322540c3beb4ba53795784eebb680/content.htm
I give you some usefull Tips.
Type /h in command Bar.
Then press F8 then system will automatically goes to debugging mode.
Then press F5. Then it shows the Each and every line of your program.
or type break-point in your SE38 program. Then press F8. it will goes to the Debugging mode.
Thanks.
Reward If Helpful.
Message was edited by:
Viji

Adobe Photoshop CS6 provides no engine for debugging

Hello,
I've been trying to diagnose a problem with my wife's copy of CS6 Web and Design premium. Basically it's unable to run any JSX script that requires the Debug engine. I receive the error message 'Adobe Photoshop CS6 provides no engine for debugging' - trying it on Illustrator also gives a similar error. Persisting by clicking the 'play' button brings up a popup error message that says 'Unable to Run Script' or something similar.
Note that if I hack our JSX script to bypass the debug engine it works fine - except certain PSDs will cause CS6 (and my older copy of CS4) to crash, so this is only a stopgap measure. Disabling OpenGL on CS4 seems to prevent crashing but it's not an option on the wife's copy since she's a full-time artist and I'm not.
This is what I've had to change -
$.level = 2; // debug level: 0-2 (0:disable, 1:break on error, 2:break at beginning)
debugger; // launch debugger on next line
Changing the $.level = 0 lets me continue without issue.
This problem does NOT exist on my laptop using the same installer downloaded from Adobe.com. (I use trial version for testing, she uses her serial no.)
Is it possible this problem persists because I uninstalled an old copy of Photoshop CS5 (standalone installation) AFTER installing CS6 Web & Design (multiple programs)?
I've tried uninstalling and reinstalling CS6, but the problem persists.
Please help, our jobs rely on this. >.<
Worst case scenario I'll copy the entire install folder over from my laptop to try and fix the problem but I'd rather not have to since we're currently working in different countries and I can only use Remote Assistance to help.

The problem is the SCRIPTS work - the debugging engine is what's missing for some reason. Even if there's a way to just cleanly uninstall everything so I can start from scratch without formatting the hard disk would be a good solution. (since apparently I think I missed some files somewhere on the last uninstall)

Can't Run program in Debug Mode

To: [email protected]
cc:
Subject: Can't Run program in Debug Mode
Has anyone else experienced this problem? We have written a non-express
program that uses the Express generated services project as a supplier
plan. However, when we try running this program in debug mode about 50%
(or more) of the time we abend while Forte is trying to partition the
application. Since we have many database classes in our Business Model we
are wondering if Forte is timing out during the partition phase or if the
server partition is running out of memory . The following error messages
are produced by Forte. Any suggestions???
=======================
Error messages on client:
=======================
SYSTEM ERROR: Unable to start the partition testacadprogoffer_CL0_Part1 on
any
of the nodes to which it has been assigned. See the remainder of the
error
stack for more information.
Class: qqsp_ResourceException
Error #: [1602, 593]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 5
Last TOOL statement: method overview.StartApplication
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Unable to start partition testacadprogoffer_CL0_Part1 on node
admin2.
Class: qqsp_ErrorDescriptor
Error #: [1602, 592]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 3
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Lost contact with remote server while trying to load
partition
testacadprogoffer_CL0_Part1. Check server log file for more information
about
the specific problem.
Class: qqsp_ResourceException
Error #: [1301, 102]
Detected at: qqem_IPartitionAgent::Startup at 5
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: The connection to the partner was terminated by the
Communication
Manager for the reasons below.
Class: qqsp_DistAccessException
Detected at: qqdo_PartitionMgr::StopLocation at 1
Error Time: Tue Dec 02 12:56:00
Distributed method called: qqrt_ForteExecAgentProxy.LoadPartition!6
(object name Unnamed) from partition "Forte_Executor", (partitionId =
F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9, taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9.229]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment CentralEnv
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Network partner closed connection. This usually means the
process at the other end of the wire failed. Please go look there and
find
out why.
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 2
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Received close: Connection aborted (10053).
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 1
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
=======================
Log messages on server:
=======================
Attached to manager for node admin2.
aud Tue Dec 2 09:34:36 : Loading partition testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 09:41:58 : Shutting down partition as requested.
aud Tue Dec 2 09:41:59 : Unloaded partition testacadprogoffer_cl0_Part2.
aud Tue Dec 2 09:49:44 : Loading partition testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:00:11 : Shutting down partition as requested.
aud Tue Dec 2 10:00:12 : Unloaded partition testacadprogoffer_cl0_Part2.
aud Tue Dec 2 10:18:34 : Loading partition testacadprogoffer_cl0_Part3
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:27:00 : Shutting down partition as requested.
aud Tue Dec 2 10:27:00 : Unloaded partition testacadprogoffer_cl0_Part3.
aud Tue Dec 2 10:47:03 : Loading partition
EvaluateApplRequirementsBO_CL0_Part1 built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 11:09:26 : Shutting down partition due to failure of agent
owner's partition.
aud Tue Dec 2 11:09:26 : Shutting down partition as requested.
aud Tue Dec 2 11:09:26 : Unloaded partition
EvaluateApplRequirementsBO_CL0_Part1.
aud Tue Dec 2 12:36:14 : Loading partition testacadprogoffer_CL0_Part1
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 12:45:17 : Shutting down partition as requested.
aud Tue Dec 2 12:45:17 : Unloaded partition testacadprogoffer_CL0_Part1.
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
Task 11: qqcm_HoseRecvServiceTask::Run: Caught unexpected exception
FATAL ERROR: ************* Out of Memory, requested (1K) available (0K)
Class: qqsp_ResourceException with ReasonCode: SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:49:01
Exception occurred (locally) on partition "Forte_Executor",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3, t
askId = [F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3.11]) in application
"Forte Runtime", pid 14020 on node admin2 in environ
ment CentralEnv.
FATAL ERROR: ************* Out of Memory, requested (1K) available (0K)
Class: qqsp_ResourceException with ReasonCode: SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:48:57
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
ERROR: TMgr.RunThread: task cm.Recv failed terminating.
Probably caused by a FATAL exception.
David Wilbur email: [email protected]
University of Windsor phone: 519-253-3000 ext. 2779
Windsor, Ontario Canada
-----------------------------------------------

Hi,
We have had the same problem in a non-express application
with a heavy server partition. In our case, the error was not
systematic, depending on the server workload at the time we
tried to partition and run.
The work-around we're using is to put the -fm flags (increasing the x
parameter to say 30000) in the 'server arguments' of your server
partition
properties in the partition workshop. Note that if your server is a Unix
platform,
you need to put double-quotes before and after the parenthesis in the -fm
syntax.
Hope this helps,
Vincent Figari
BTW, what Forte version are you using ?
On Tue, 2 Dec 1997 13:44:24 -0500 "David Wilbur"<[email protected]>
writes:
>
>
>
>
>
To: [email protected]
cc:
Subject: Can't Run program in Debug Mode
Has anyone else experienced this problem? We have written a
non-express
program that uses the Express generated services project as a supplier
plan. However, when we try running this program in debug mode about
50%
(or more) of the time we abend while Forte is trying to partition the
application. Since we have many database classes in our Business
Model we
are wondering if Forte is timing out during the partition phase or if
the
server partition is running out of memory . The following error
messages
are produced by Forte. Any suggestions???
=======================
Error messages on client:
=======================
SYSTEM ERROR: Unable to start the partition
testacadprogoffer_CL0_Part1 on
any
of the nodes to which it has been assigned. See the remainder of
the
error
stack for more information.
Class: qqsp_ResourceException
Error #: [1602, 593]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 5
Last TOOL statement: method overview.StartApplication
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Unable to start partition testacadprogoffer_CL0_Part1 on
node
admin2.
Class: qqsp_ErrorDescriptor
Error #: [1602, 592]
Detected at: qqcf_StandardConfig::LoadRemotePartition at 3
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
SYSTEM ERROR: Lost contact with remote server while trying to load
partition
testacadprogoffer_CL0_Part1. Check server log file for more
information
about
the specific problem.
Class: qqsp_ResourceException
Error #: [1301, 102]
Detected at: qqem_IPartitionAgent::Startup at 5
Error Time: Tue Dec 02 12:56:01
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: The connection to the partner was terminated by the
Communication
Manager for the reasons below.
Class: qqsp_DistAccessException
Detected at: qqdo_PartitionMgr::StopLocation at 1
Error Time: Tue Dec 02 12:56:00
Distributed method called:
qqrt_ForteExecAgentProxy.LoadPartition!6
(object name Unnamed) from partition "Forte_Executor",
(partitionId =
F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9, taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9.229]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Network partner closed connection. This usually means
the
process at the other end of the wire failed. Please go look there
and
find
out why.
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 2
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
INFORMATION: Received close: Connection aborted (10053).
Class: qqsp_DistAccessException
Detected at: qqcm_HoseFSM::ReceivedClose at 1
Error Time: Tue Dec 02 12:56:00
Exception occurred (locally) on partition "Express_cl7_Client",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3,
taskId =
[F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10e9:0x3.226]) in
application
"FTLaunch_cl0", pid 65 on node DWILBUR_NTWS in environment
CentralEnv.
=======================
Log messages on server:
=======================
Attached to manager for node admin2.
aud Tue Dec 2 09:34:36 : Loading partition
testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 09:41:58 : Shutting down partition as requested.
aud Tue Dec 2 09:41:59 : Unloaded partition
testacadprogoffer_cl0_Part2.
aud Tue Dec 2 09:49:44 : Loading partition
testacadprogoffer_cl0_Part2
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:00:11 : Shutting down partition as requested.
aud Tue Dec 2 10:00:12 : Unloaded partition
testacadprogoffer_cl0_Part2.
aud Tue Dec 2 10:18:34 : Loading partition
testacadprogoffer_cl0_Part3
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 10:27:00 : Shutting down partition as requested.
aud Tue Dec 2 10:27:00 : Unloaded partition
testacadprogoffer_cl0_Part3.
aud Tue Dec 2 10:47:03 : Loading partition
EvaluateApplRequirementsBO_CL0_Part1 built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 11:09:26 : Shutting down partition due to failure of
agent
owner's partition.
aud Tue Dec 2 11:09:26 : Shutting down partition as requested.
aud Tue Dec 2 11:09:26 : Unloaded partition
EvaluateApplRequirementsBO_CL0_Part1.
aud Tue Dec 2 12:36:14 : Loading partition
testacadprogoffer_CL0_Part1
built on <unknown>.
Attached to manager for node admin2.
aud Tue Dec 2 12:45:17 : Shutting down partition as requested.
aud Tue Dec 2 12:45:17 : Unloaded partition
testacadprogoffer_CL0_Part1.
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
Task 11: qqcm_HoseRecvServiceTask::Run: Caught unexpected exception
FATAL ERROR: ************* Out of Memory, requested (1K) available
(0K)
Class: qqsp_ResourceException with ReasonCode: SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:49:01
Exception occurred (locally) on partition "Forte_Executor",
(partitionId = F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3, t
askId = [F88CCF80-FA5D-11D0-A2F1-DA164885AA77:0x10f3.11]) in
application
"Forte Runtime", pid 14020 on node admin2 in environ
ment CentralEnv.
FATAL ERROR: ************* Out of Memory, requested (1K) available
(0K)
Class: qqsp_ResourceException with ReasonCode:
SP_ER_OUTOFMEMORY
Detected at: qqos_MemoryManager
Error Time: Tue Dec 2 12:48:57
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
FATAL ERROR: Out of Memory (reason = qqOS_MM_EX_OUT_OF_MEMORY)
ERROR: TMgr.RunThread: task cm.Recv failed terminating.
Probably caused by a FATAL exception.
David Wilbur email: [email protected]
University of Windsor phone: 519-253-3000 ext. 2779
Windsor, Ontario Canada

Is there a Replacement Program for 2009 iMacs with MXM Graphics Cards?

I have an iMac 24" Early 2009 with the Nvidia GeForce GT 120 256MB MXM graphics card that is freezing and crashing over-and-over, especially when I'm away and it's not connected to my 2nd display! Odd. I've done the usual (cleaned the iMac inside, run fsck, SMC reset, PRAM reset, repair permissions from boot USB, disconnected all peripherals, changed mice and keyboards, changed the HD, reinstalled the OS, run Onyx and so on) and finally decided that it's a faulty graphics card that only a replacement will fix. When I'm home it's more stable when connected via a Displayport DVI adapter to DVI cable to a 24" Dell display. When standalone (like when traveling with my iMac for long stints out of town) it's unusable. It won't run for longer than 30 minutes, often not even 10 minutes, then I get screen artifacts and freezes and then have to fsck to repair the drive before running it again. Only running it in Safe Mode will allow it to run reliably.
However, I believe that I found a stopgap solution. I installed a program which I downloaded after installing XCode called Quartz Debug which has apparently allowed me to disable Quartz Extreme, 2D Acceleration and Quartz GL.
Turning off all Quartz graphics enhancements makes this machine stable if not exactly completely "mac-like" in its performance, but it's at least usable under most conditions for long periods of time. I know of people who have replaced the MXM graphics card on this machine with good effect, but it's an expensive proposition and these cards are apparently few and far between. Has anyone done this?
Based on the large number of nearly identical complaints about this model, both here and elsewhere, it seems like this MXM graphics card is defective or Apple's drivers are defective . . . well maybe, but it very, very predictably crashes when the computer gets hotter and not even _extremely_ hot, but well within what would be normal operating temps for other machines.
I've disassembled and completely cleaned the inside and have replaced the HD with an SSD and removed the optical drive entirely so if anything I've reduced heat-producing devices from the interior of the device installed a fan control and keep the graphics card features mostly turned off.
I've looked for but have yet to see a recall or warranty replacement program for this device and no, I don't have Applecare. I've owned several Apple products in the last two decades and with the issues with Apple products in recent years, it seems like Applecare must be figured as part of any Apple purchase if reliability and ongoing support is desired.
Ironically, I have an Apple IIc and a Power Computing Power Tower 166 that still work just fine, thank you!
JoeL
Atlanta, GA

This cropped up on my wife's late 2009 model 27" iMac, too. Random freezes were encountered, unable to identify cause for months, then one day it started to become unable to complete a normal boot. Tech Tool Deluxe was the only direct indication as far as diagnostics are concerned. I've NEVER been abvle to get Apple's hardware diagnostic to run from the cloud, and we fianlly got it on a Techs' bench, AHT showed nothing wrong. As you said, Safe boot is the only way to get into the system, and performance under 10.8.5 is glacial.
Now the kicker - we DID have AppleCare, and this phase of the MXM graphics demise hit within 4 or 5 months of AppleCare expiration. There's no longer a flat-rate repair option, Apple doesn't have any stock of the video board to sell as a replacement part (was $169, or $179 w/no exchange) and even refurbs of this paltry (512MB VRAM) board can hit $300. I know Mac users have become 2nd-class citizens in Apple's business universe, but we're now looking at sub-42 month lifespans for hardware? At $2k for a machine that lacks touchscreen option, that's out of line.

I need Java code for a simple graphical hit counter for a webpage

I was wondering if anybody out there could send me some code for a simple graphical hit counter for a webpage. All the sites that I've visited are garbage and of no use to me. Please help me.
Colin

Not as easy as you'd imagine with applets. You need some way to store the hits, usually through a file on the server. That's not gonna happen in a hurry for 2 reasons -
- Applets can't read/write files
- Your web server usually won't let you run programs on their machine (ie, programs that listen for socket connections from applets, then load/read/write/close a file).
In short, no, there is no simple java solution (that I know of).
Cheers,
Radish21

Dump in smartform driver program for purchase order

i created one smartform with driver program for purchase order.
in smartfrom i gave
form interface: p_ebeln as import,
                    tables as it_ekpo like ekpo.
global definitions are
wa_ekko type ekko for printing the ekko data in one window,
                                       wa_ekpo type ekpo .
in main window i took the one table and loop the ekpo table for printing the item details.
no errors is there.but ; when i call this generated function module to my driver program it goes to dump.
in driver program i declare structures,internal tables,work areas, and parameter as p_ebeln .
and also select statements for my table all are good.but its not work.
in function module i pass the details as export p_ebeln = p_ebeln and table it_ekpo = it_ekpo.
and also i done debugging in this data come to the internal table and work areas.
but it goes to dump.
if u dont mind plz solve my problem.
Thanks
Navya.
Moderator message: empty lines removed, subject corrected, please use meaningful subject lines when posting!
Edited by: Thomas Zloch on Mar 24, 2011 10:10 AM

Hi Navya,
Your smartform is correct. But, as per my understanding, the dump comes when you call the smartform from the driver program. If that is the case, please check the input parameters and all th parameters in the program should be same as used in samrtform. Any deviation would lead to a dump.
Analyse and resolve!!!
Regards
Atul Sachdeva

Connect with different server for debugging

hi to all,
is it possible to connect to a different server for debugging? this is to share the development environment !!
please advise.

Hi,
Thanks for your question
You can create SharePoint 2013 project in your Visual studio 2013 without installing SharePoint on your local machine.
Please follow below steps : Go to the server where SharePoint 2013 is installed and follow steps from 1 to 3
Go to Run and type "regedit"
Navigate towards HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Office
Right click on 15.0 and click Export. Save the exported file
Now go to your machine where sharepoint is not installed and follow below steps:
Now open Registry on your machine
Import the 15 directory which was exported from SharePoint server
Open Powershell
Run this command
Set-ItemProperty -Path "HKLM:\Software\Microsoft\Shared Tools\web server extensions\15.0\" -Name "Location" -Value "C:\Program Files\Common Files\Microsoft Shared\Web Server Extensions\15\"
Now open visual studio 2013 and you will be able to create SharePoint 2013 project without error.
I hope this is helpful to you. If this works, Please mark it as Answered.
Regards,
Dharmendra Singh (MCPD-EA | MCTS)
Blog : http://sharepoint-community.net/profile/DharmendraSingh

How to run labview program in debugging mode in windows 95 version

Respected all,
I am facing probelm while running probe.vi.
I received this command "connection to acquisition board was not found" when i run labview program.
I am using labview 5.1, fieldpoint FP 1000, NI-DAQ 6.5, Field point explorer version 1.6, Measurement and Automation Explorer 1.0.1.
I would kindly request you please help me how to run my program probe.vi in debugging mode in windows 95 version, so that i can locate where error occurs.
Thanking You
Yours faithfully
M.Vijay

Respected Norbert,
Thank you very much to for your help.
Norbert : Possible reasons are e.g. wrong IDs for measurement devices. If the error is connect to the FieldPoint, it is possible that it isn't configured correctly.
I am using Field point explorer 1.6, The Field point instrument FP 1000 and RS-232 port is using. It is confirmed that the field point instrument is working properly by LED light indication test.
Norbert: It sound like you are using DAQ devices (like PCI MIO 6952E) in the application. Are you sure that you select the correct device ID for this?
I am asking you to know, If i using Labview and Fieldpoint instrument FP 1000 to monitor my parameter interms of All, Channel 0, Channel 1, Channel 2, Channel 3, Channel 4, Channel 5, Channel 6, Channel 7 for my measurement.
But now i need to solve the command connection to acquisition board was not found, The expert say this command is due to there was no AT-AO-10 Analog Output board was present in CPU.
I do not find AT-AO-10 Analog Output board in my CPU, Previously the instrument was worked perfectly by other person who assembled everthing to measure temperature.
The only aswer know send by previous person is if my task does not imply the use of a DAQ you probably have to locate where the DAQ driver is called and exclude it from the program. try to run the program in debugging mode so that you can locate where the error occurs.
I do not know how to proceed his instruction. So i would kindly request you to please help me to solve my probelm.
I also removed AT-AO-10 software from device manager >> Data Acquisition system >> AT-AO-10 just now.
I also find GPIB version 1.30, when i remove in add or remove program, it say that Error removing the GPIB.
I am eagerly waiting for your help.
Thanking You
Yours faithfully
M.vijay

ABAP Sample Program for T Code FFB4

Hi guys: I have the structure that t code FFB4 requires, but now I need to code a program for SAP to read the csv or text file and convert it automatically to match the structures required by FFB4 to post successfully. Does anyone please have a sample program that they have written for this purpose? The CSV/txt file is being generated by an external system but now SAP needs to make sense of it.
The structures are:
Header record (record type 0, structure FEBSCSA).
Memo record    (record type 1, structure FEBSCSB).
Clearing record (record type 2, structure FEBSCSC).
Please provide a sample code so I can debug & tweak it.
Thanks so much
Full points will be rewarded.
Brian

No. However, you just have to write a custom program to do the following.
data : gi_filename like rlgrap-filename,
         gi_name     like thead-tdname," You image name
         gi_spras    like thead-tdspras,
         gi_object   like thead-tdobject value 'GRAPHICS',
         gi_id       like thead-tdid value 'BMAP',
         l_extension like rlgrap-filename value 'BMP',
         gi_title    like bapisignat-prop_value,
         gi_resident like rsscg-resident,
         gi_btype    like stxbitmaps-tdbtype value 'BMON',
         gi_autoheight like rsscg-autoheight value ' ',
         gi_resolution like stxbitmaps-resolution value '600',
         l_stxbitmaps like stxbitmaps.
For each image do the following perform.
perform import_bitmap_bds(saplstxbitmaps)
                            using    gi_filename
                                     gi_name
                                     gi_object
                                     gi_id
                                     gi_btype
                                     l_extension
                                     gi_title
                                     gi_resident
                                     gi_autoheight
                       changing l_docid
                                     gi_resolution.

Console program for iPhone terminated in 20 seconds on simulator

Hi,
I have a console program for iPhone which simply uses printf to output. It works fine on iphone but not on Simulator.
I noticed that iphone has a watchdog time to stop a program which loading more than 20 seconds. I believe the simulator treats my console application as a always loading one and terminated after 20 seconds. The evidence is if I cut my program into small pieces (finish running in 20 seconds), and run them piece by piece, no any problem happens.
Since my customer wants that program runs on simulator as one piece, I'd like to ask if there is a simple way to turn off the 20 second timer, or let simulator know I am not loading anything.
Thanks.

I start my program from XCode IDE by 'Build and Go', then choose menu Run->Console to open the debugging console, I will see my printfs there.
After 20 senconds, the output stops, on the bottom of Console window, I see 'debugging terminated'.

Idoc inbound posting program for CRMXIF_PARTNER_SAVE_M02

Hi Abapers,
Im working on datamigration for Business partner using Lsmw idoc method and getting Idoc status 53 with message crmxif_partner_save function module generated successfully with BP number but some of the entries of the fields is not getting inserted into master table BUT000,can any one put a tip of light what exactly is going wrong as i have taken all necesscary steps if any one can share their views like how to trace the posting program for inbound idoc crmxif_partner_save_m02 and where exactly the data is getting inserted into database table BUT000.
Will appreciate all your help.

Hello,
at first, that would be very useful if you could say which fields/segments exactly are not transfered...
there can be lot's of reasonsd why the fields are not inserted with 53 result status, but in general you can try several points:
1. check if all the fields you want to transport are properly mapped
2. you can try to debug, if indeed your mapping rules are working during convertion
3. do you want to fill this fields in insert (to create new BP) or update mode (udate already created BP)?
etc.
regards,

I looking for a transaction for debug the IDOCS

Hello friends,
I looking for a transaction that allowed me to debug the IDOC´s when the direction is only 1 (Outbound), for ex. for IDOC´s has direction 2 (Inbound) I used the WE19 transaction, and to choose the "Inbound Function Module" button and I take the "Call in debug mode" checkbox,
Can you tell me if exist another program for this?
Thanks in advance,
David

Hi,
IDocs are processed by a function module, which are mapped against in table EDIFCT. When you process an IDoc with BD87 you can have a breakpoint in the function and it will stop. For outbound processing it depends on which program is sending the IDoc. For transactional data like purchase orders, the IDoc is created via RSNAST00 which in turn calls a function module assigned to the processing code (BD41).
For your knowledge [reference1|Re: How to debug Idoc; [reference2|Outbound IDoc debug;.
May it helps you.
Regards,
DS.

Programming for the mac without using xcode

Hi
I'm very new to programming for Apple platform. I wanted to clear some doubts which is currently standing as a barrier in getting started.
Can I use a text editor (preferably TextMate), Interface Builder, and the Terminal (without using xcode to write & compile) to develop software for the Mac. I have installed the xcode package (~900 mb image).
Can you point me to some resources on terminal commands for compile, debug codes for the mac. (Obj-C, Cocoa api)
Thank You.
Message was edited by: jase21

You can use anything you want to develop software for the Mac. In fact, I always encourage people to start out with tutorials and examples using standard UNIX command line tools like vi and gcc. There are plenty of such getting started tutorials for UNIX and Linux.
At some point, however, the command line is going to get cumbersome. You may want go start writing true Mac applications instead if command line tools. Then it will be time to start with Xcode.

How to use debugproxy for debugging on AS-Java?

Dear Sirs,
I'd like to debug java program on AS-Java without occupying AS-Java instance.
I expect debugproxy can help it.
I could enable it on SAP Management Console, but I don't know how to use it with NWDS.
Could I get instraction of using debugproxy with NWDS?
In addition, I'm afraid that my idea is feasible and debugging always occupy AS-Java instance. It means I have to have another instance specified for debugging.
Please advise me.
Best regards,
Shingo Suzuki

Hi Shingo,
Not always
Check [this|SAP NW CE 7.1: Start Debug Session... vs. Enable Debugging; thread.
HTH!
\-- Vladimir

Program for debugging webpage

Similar Messages

Maybe you are looking for