Pull a report of Anyconnect clients in use

Is there a way to find out who is connecting with which version of the Anyconnect client within the ASA?

Another 'workaround' that you can do to get historical data is set up dap policies. If you are using the HostScan feature, set up separate dap policies for each version of anyconnect you think people might have. If you are externally syslogging the data, you can search through the logs and find unique users with what versions they are using.

Similar Messages

AnyConnect Client

Does the AnyConnect client only use SSL or can it support IPSec?

It will support both. Personally to answer your question - I would go with the SSL Any Client option, Cisco appear to be moving into the SSL-VPN direction, compared to the IPSEC Client.

Unable to use proxy server with MAC OS X Anyconnect client

Hi All,
I have a VPN setup thru a Cisco 5520, Windows clients connect just find and the end users configure there browser to use our internal proxy servers. Users with the MAC OS X Anyconnect client can connect, they configure their Mac to use our proxy server, but the broswers will not work, clients can reach networks and resources behind the VPN gateway and have access to the Proxy(Tried a telnet to that hostname/port). Anyone run into this issue before? I am running ASA 8.3(2), Anyconnect(OS X) 3.1.01065.
Thank You

We had the same problem.
We are behind government firewall so I don't know which Cisco firewall is used but we are using AnyConnect to establish VPN from internet to LAN behind firewall. We have no problems with Windows. With Mac OS X connection through proxy didn't work with Safari and Chrome (both are using system Proxy setting), but it did work with Firefox (which has it's own Proxy).
Finally we found out that ethernet MTU size was the culprit. When we set it to manual, with size being 1347 (or less), proxy started to work.

XE connection problem after using Cisco AnyConnect Client

Hello
I have a rather annoying problem connecting to an XE instance AFTER I have disconnected from a VPN via a Cisco AnyConnect VPN Agent.
Sequence of operations:
- start Oracle XE and work normally
- connect to client's vpn
- do other stuff
- DISCONNECT from Client's VPN
-> unable to connect to XE service any more, unless I reboot
The problem does not happen with other vpn clients like Cisco VPN Service, Juniper, Checkpoint.
Details:
- sqlplus connection WITH service name (eg sqlplus user/pwd@XE): FAILURE with ORA-12170
- but...sqlplus connection WITHOUT service name (eg sqlplus user/pwd): SUCCESS (weird !)
- tnsping XE: TNS-12535 error
- lsnrctl status output (sorry, italian localized)
LSNRCTL for 32-bit Windows: Version 10.2.0.1.0 - Production on 22-GIU-2011 14:19
:38
Copyright (c) 1991, 2005, Oracle. All rights reserved.
Connessione a (DESCRIPTION=(ADDRESS=(PROTOCOL=IPC)(KEY=EXTPROC_FOR_XE)))
STATO del LISTENER
Alias LISTENER
Versione TNSLSNR for 32-bit Windows: Version 10.2.0.1.0 - Produ
ction
Data di inizio 22-GIU-2011 12:26:15
Tempo di attivitÓ 0 giorni 1 ore 53 min. 22 sec.
Livello trace off
Sicurezza ON: Local OS Authentication
SNMP OFF
Servizio predefinito XE
File di parametri listenerC:\programs\oraclexe\app\oracle\product\10.2.0\server\
network\admin\listener.ora
File di log listener C:\programs\oraclexe\app\oracle\product\10.2.0\server\
network\log\listener.log
Summary table degli endpoint di ascolto...
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\EXTPROC_FOR_XEipc)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1521)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=MyPCName)(PORT=8080))(Presentation=HTTP)(Session=RAW))
Summary table dei servizi...
Il servizio "CLRExtProc" ha 1 istanze.
L'istanza "CLRExtProc", stato UNKNOWN, ha 1 handler per questo servizio...
Il servizio "PLSExtProc" ha 1 istanze.
L'istanza "PLSExtProc", stato UNKNOWN, ha 1 handler per questo servizio...
Il servizio "XEXDB" ha 1 istanze.
L'istanza "xe", stato READY, ha 1 handler per questo servizio...
Il servizio "XE_XPT" ha 1 istanze.
L'istanza "xe", stato READY, ha 1 handler per questo servizio...
Il servizio "xe" ha 1 istanze.
L'istanza "xe", stato READY, ha 1 handler per questo servizio...
Environment:
Win7 Pro SP1
Oracle XE 10.2.0
I have stopped the Win firewall and the problem is still there, so it is not a firewall problem
listener.ora configuration
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = C:\programs\oraclexe\app\oracle\product\10.2.0\server)
(PROGRAM = extproc)
(SID_DESC =
(SID_NAME = CLRExtProc)
(ORACLE_HOME = C:\programs\oraclexe\app\oracle\product\10.2.0\server)
(PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC_FOR_XE))
(ADDRESS = (PROTOCOL = TCP)(HOST = MyPCName)(PORT = 1521))
DEFAULT_SERVICE_LISTENER = (XE)
tnsnames.ora
XE =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = MyPCName)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = XE)
EXTPROC_CONNECTION_DATA =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC_FOR_XE))
(CONNECT_DATA =
(SID = PLSExtProc)
(PRESENTATION = RO)
Any help ?

Hi;
Pelase close this tread as answered and keep update issue at:
Re: XE connection problem after using Cisco AnyConnect Client
Regard
Helios

Anyconnect client and clientless connections hang for two users

ASA 5525, v. 9.1(5)19
Anyconnect client 3.1.02026
I have two users who are unable to connect via the AC client or clientless through the web portal. Using the client, it will get stuck in a loop of "checking for updates". On the portal, the connection will proceed to the point of "Cisco Secure Desktop successfully validated... Success.. Reloading..please wait." Then it hangs there.
The issue occurs for the user regardless of which company laptop she logs onto. A help desk tech can use her laptop and successfully connect, but she cannot connect on her own laptop or on another laptop. (Same for the other user.) So the issue doesn't seem to be related to her laptop or the AC installation. (Help desk did reimage her machine early in the troubleshooting process before they realized that the issue seemed to follow the user.)
I've updated the hostscan file - no change in results. Client and clientless connections seem to be working fine for all other users. We're stumped. Suggestions, anyone? thanks!

The LDAP should be server folks -- Active Directory. Chances are whoever manages the ASA's should have access to at least look in Active Directory to look that up. If they don't they need it.
I obviously don't know a lot about what devices you are using, but if you are using ISE, there should be some type of MNT device (Monitoring and Troubleshooting) -- which is collecting the logs and, hopefully, sending them to some type of syslog aggregate collection tool (splunk?).
Otherwise, there should be a device called a CAM (Clean Access Manager) that is collecting logs -- which may also be propagated to a syslog aggregate tool -- although with CAM's, you can pull the reports right out of them in a comma deliminated file (.csv) and go through them that way.
-- The thing that gets me is that it happens to two users no matter what computer they try to connect from, no matter what network they connect from, and other users can authenticate and gain network access on those same devices.
-- That is why it is rather perplexing. Pretty much saying it has to be something with:
- the IP pool they are getting an IP from
- their AD credentials
- their username
- something along those lines, if the information provided was fully accurate.

AnyConnect error " User not authorized for AnyConnect Client access, contact your administrator"

Hi everyone,
it's probably just me but I have tried real hard to get a simple AnyConnect setup working in a lab environment on my ASA 5505 at home, without luck. When I connect with the AnyConnect client I get the error message "User not authorized for AnyConnect Client access, contact your administrator". I have searched for this error and tried some of the few solutions out there, but to no avail. I also updated the ASA from 8.4.4(1) to 9.1(1) and ASDM from 6.4(9) to 7.1(1) but still the same problem. The setup of the ASA is straight forward, directly connected to the Internet with a 10.0.1.0 / 24 subnet on the inside and an address pool of 10.0.2.0 / 24 to assign to the VPN clients. Please note that due to ISP restrictions, I'm using port 44455 instead of 443. I had AnyConnect working with the SSL portal, but IKEv2 IPsec is giving me a headache. I have stripped down certificate authentication which I had running before just to eliminate this as a potential cause of the issue. When running debugging, I do not get any error messages - the handshake completes successfully and the local authentication works fine as well.
Please find the current config and debugging output below. I appreciate any pointers as to what might be wrong here.
: Saved
ASA Version 9.1(1)
hostname ASA
domain-name ingo.local
enable password ... encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd ... encrypted
names
name 10.0.1.0 LAN-10-0-1-x
dns-guard
ip local pool VPNPool 10.0.2.1-10.0.2.10 mask 255.255.255.0
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif Internal
security-level 100
ip address 10.0.1.254 255.255.255.0
interface Vlan2
nameif External
security-level 0
ip address dhcp setroute
regex BlockFacebook "facebook.com"
banner login This is a monitored system. Unauthorized access is prohibited.
boot system disk0:/asa911-k8.bin
ftp mode passive
clock timezone PST -8
clock summer-time PDT recurring
dns domain-lookup Internal
dns domain-lookup External
dns server-group DefaultDNS
name-server 10.0.1.11
name-server 75.153.176.1
name-server 75.153.176.9
domain-name ingo.local
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network LAN-10-0-1-x
subnet 10.0.1.0 255.255.255.0
object network Company-IP1
host xxx.xxx.xxx.xxx
object network Company-IP2
host xxx.xxx.xxx.xxx
object network HYPER-V-DUAL-IP
range 10.0.1.1 10.0.1.2
object network LAN-10-0-1-X
access-list 100 extended permit tcp any4 object HYPER-V-DUAL-IP eq 3389 inactive
access-list 100 extended permit tcp object Company-IP1 object HYPER-V-DUAL-IP eq 3389
access-list 100 extended permit tcp object Company-IP2 object HYPER-V-DUAL-IP eq 3389
tcp-map Normalizer
check-retransmission
checksum-verification
no pager
logging enable
logging timestamp
logging list Threats message 106023
logging list Threats message 106100
logging list Threats message 106015
logging list Threats message 106021
logging list Threats message 401004
logging buffered errors
logging trap Threats
logging asdm debugging
logging device-id hostname
logging host Internal 10.0.1.11 format emblem
logging ftp-bufferwrap
logging ftp-server 10.0.1.11 / asa *****
logging permit-hostdown
mtu Internal 1500
mtu External 1500
ip verify reverse-path interface Internal
ip verify reverse-path interface External
icmp unreachable rate-limit 1 burst-size 1
icmp deny any echo External
asdm image disk0:/asdm-711.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network obj_any
nat (Internal,External) dynamic interface
object network LAN-10-0-1-x
nat (Internal,External) dynamic interface
object network HYPER-V-DUAL-IP
nat (Internal,External) static interface service tcp 3389 3389
access-group 100 in interface External
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa-server radius protocol radius
aaa-server radius (Internal) host 10.0.1.11
key *****
radius-common-pw *****
user-identity default-domain LOCAL
aaa authentication ssh console radius LOCAL
http server enable
http LAN-10-0-1-x 255.255.255.0 Internal
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev2 ipsec-proposal AES256 AES192 AES 3DES DES
crypto map External_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map External_map interface External
crypto ca trustpoint srv01_trustpoint
enrollment terminal
crl configure
crypto ca trustpoint asa_cert_trustpoint
keypair asa_cert_trustpoint
crl configure
crypto ca trustpoint LOCAL-CA-SERVER
keypair LOCAL-CA-SERVER
crl configure
crypto ca trustpool policy
crypto ca server
cdp-url http://.../+CSCOCA+/asa_ca.crl:44435
issuer-name CN=...
database path disk0:/LOCAL_CA_SERVER/
smtp from-address ...
publish-crl External 44436
crypto ca certificate chain srv01_trustpoint
certificate <output omitted>
quit
crypto ca certificate chain asa_cert_trustpoint
certificate <output omitted>
quit
crypto ca certificate chain LOCAL-CA-SERVER
certificate <output omitted>
quit
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-192
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable External client-services port 44455
crypto ikev2 remote-access trustpoint asa_cert_trustpoint
telnet timeout 5
ssh LAN-10-0-1-x 255.255.255.0 Internal
ssh xxx.xxx.xxx.xxx 255.255.255.255 External
ssh xxx.xxx.xxx.xxx 255.255.255.255 External
ssh timeout 5
ssh version 2
console timeout 0
no vpn-addr-assign aaa
no ipv6-vpn-addr-assign aaa
no ipv6-vpn-addr-assign local
dhcpd dns 75.153.176.9 75.153.176.1
dhcpd domain ingo.local
dhcpd option 3 ip 10.0.1.254
dhcpd address 10.0.1.50-10.0.1.81 Internal
dhcpd enable Internal
threat-detection basic-threat
threat-detection scanning-threat shun except ip-address LAN-10-0-1-x 255.255.255.0
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
dynamic-filter use-database
dynamic-filter enable interface Internal
dynamic-filter enable interface External
dynamic-filter drop blacklist interface Internal
dynamic-filter drop blacklist interface External
ntp server 128.233.3.101 source External
ntp server 128.233.3.100 source External prefer
ntp server 204.152.184.72 source External
ntp server 192.6.38.127 source External
ssl encryption aes256-sha1 aes128-sha1 3des-sha1
ssl trust-point asa_cert_trustpoint External
webvpn
port 44433
enable External
dtls port 44433
anyconnect image disk0:/anyconnect-win-3.1.02026-k9.pkg 1
anyconnect profiles profile1 disk0:/profile1.xml
anyconnect enable
smart-tunnel list SmartTunnelList1 mstsc mstsc.exe platform windows
smart-tunnel list SmartTunnelList1 putty putty.exe platform windows
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1 ikev2 l2tp-ipsec ssl-client ssl-clientless
webvpn
anyconnect profiles value profile1 type user
username write.ingo password ... encrypted
username ingo password ... encrypted privilege 15
username tom.tucker password ... encrypted
class-map TCP
match port tcp range 1 65535
class-map type regex match-any BlockFacebook
match regex BlockFacebook
class-map type inspect http match-all BlockDomains
match request header host regex class BlockFacebook
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 1500
id-randomization
policy-map TCP
class TCP
set connection conn-max 1000 embryonic-conn-max 1000 per-client-max 250 per-client-embryonic-max 250
set connection timeout dcd
set connection advanced-options Normalizer
set connection decrement-ttl
policy-map type inspect http HTTP
parameters
protocol-violation action drop-connection log
class BlockDomains
policy-map global_policy
class inspection_default
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect dns preset_dns_map dynamic-filter-snoop
inspect http HTTP
service-policy global_policy global
service-policy TCP interface External
smtp-server 199.185.220.249
privilege cmd level 3 mode exec command perfmon
privilege cmd level 3 mode exec command ping
privilege cmd level 3 mode exec command who
privilege cmd level 3 mode exec command logging
privilege cmd level 3 mode exec command failover
privilege cmd level 3 mode exec command vpn-sessiondb
privilege cmd level 3 mode exec command packet-tracer
privilege show level 5 mode exec command import
privilege show level 5 mode exec command running-config
privilege show level 3 mode exec command reload
privilege show level 3 mode exec command mode
privilege show level 3 mode exec command firewall
privilege show level 3 mode exec command asp
privilege show level 3 mode exec command cpu
privilege show level 3 mode exec command interface
privilege show level 3 mode exec command clock
privilege show level 3 mode exec command dns-hosts
privilege show level 3 mode exec command access-list
privilege show level 3 mode exec command logging
privilege show level 3 mode exec command vlan
privilege show level 3 mode exec command ip
privilege show level 3 mode exec command failover
privilege show level 3 mode exec command asdm
privilege show level 3 mode exec command arp
privilege show level 3 mode exec command ipv6
privilege show level 3 mode exec command route
privilege show level 3 mode exec command ospf
privilege show level 3 mode exec command aaa-server
privilege show level 3 mode exec command aaa
privilege show level 3 mode exec command eigrp
privilege show level 3 mode exec command crypto
privilege show level 3 mode exec command ssh
privilege show level 3 mode exec command vpn-sessiondb
privilege show level 3 mode exec command vpnclient
privilege show level 3 mode exec command vpn
privilege show level 3 mode exec command dhcpd
privilege show level 3 mode exec command blocks
privilege show level 3 mode exec command wccp
privilege show level 3 mode exec command dynamic-filter
privilege show level 3 mode exec command webvpn
privilege show level 3 mode exec command service-policy
privilege show level 3 mode exec command module
privilege show level 3 mode exec command uauth
privilege show level 3 mode exec command compression
privilege show level 3 mode configure command interface
privilege show level 3 mode configure command clock
privilege show level 3 mode configure command access-list
privilege show level 3 mode configure command logging
privilege show level 3 mode configure command ip
privilege show level 3 mode configure command failover
privilege show level 5 mode configure command asdm
privilege show level 3 mode configure command arp
privilege show level 3 mode configure command route
privilege show level 3 mode configure command aaa-server
privilege show level 3 mode configure command aaa
privilege show level 3 mode configure command crypto
privilege show level 3 mode configure command ssh
privilege show level 3 mode configure command dhcpd
privilege show level 5 mode configure command privilege
privilege clear level 3 mode exec command dns-hosts
privilege clear level 3 mode exec command logging
privilege clear level 3 mode exec command arp
privilege clear level 3 mode exec command aaa-server
privilege clear level 3 mode exec command crypto
privilege clear level 3 mode exec command dynamic-filter
privilege cmd level 3 mode configure command failover
privilege clear level 3 mode configure command logging
privilege clear level 3 mode configure command arp
privilege clear level 3 mode configure command crypto
privilege clear level 3 mode configure command aaa-server
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:41a021a28f73c647a2f550ba932bed1a
: end
Many thanks,
Ingo

Hi Jose,
here is what I got now:
ASA(config)# sh run | begin tunnel-group
tunnel-group DefaultWEBVPNGroup general-attributes
address-pool VPNPool
authorization-required
and DAP debugging still the same:
ASA(config)# DAP_TRACE: DAP_open: CDC45080
DAP_TRACE: Username: tom.tucker, aaa.cisco.grouppolicy = DfltGrpPolicy
DAP_TRACE: Username: tom.tucker, aaa.cisco.username = tom.tucker
DAP_TRACE: Username: tom.tucker, aaa.cisco.username1 = tom.tucker
DAP_TRACE: Username: tom.tucker, aaa.cisco.username2 =
DAP_TRACE: Username: tom.tucker, aaa.cisco.tunnelgroup = DefaultWEBVPNGroup
DAP_TRACE: Username: tom.tucker, DAP_add_SCEP: scep required = [FALSE]
DAP_TRACE: Username: tom.tucker, DAP_add_AC:
endpoint.anyconnect.clientversion="3.1.02026";
endpoint.anyconnect.platform="win";
DAP_TRACE: Username: tom.tucker, dap_aggregate_attr: rec_count = 1
DAP_TRACE: Username: tom.tucker, Selected DAPs: DfltAccessPolicy
DAP_TRACE: Username: tom.tucker, DAP_close: CDC45080
Unfortunately, it still doesn't work. Hmmm.. maybe a wipe of the config and starting from scratch can help?
Thanks,
Ingo

Which Oracle client to use? with CRS2008 on Windows 2008 R2 64bit

Hi,
We are setting up a standalone Crystal Reports 2008 Server on Windows 2008 R2 64bit. This server will serve some reports that will pull data from an Oracle 11g DB. Several Oracle 10g/11g, (32bit or 64bit) DB client has been tried, but CRS cannot connect to the oracle DB using any of them. Which oracle client is known to be working well on this setup?
CRS 2008 <> Windows 2008 R2 64 bit <> Xeon E5600 series machine
Thanks,
Steve

Hello,
CRS2008 v1 supports Oracle 9.2, 10g R1, 10G R2 and 11g R1.
The client to use on those version are the same as the server meaning if you have a 11g R1 server then you can use an Oracle Net Client 11G R1. But you can use also a JDBC, ODBC, OLEDB Oracle 11G R1.
If you have a CRS2008 v0, then Oracle 11G is not supported. Only 9.2, 10g R1 and 10G R2.
I hope this will help you
Regards,
Philippe

Crystal Reports 9 and Stored Procedures using supplied parameters from user

Hi,
I have a Crystal Reports 9 report that prints and works fine. It requests from the user 2 pieces of data which both are String data and not nulls. I want to use the same report in a Visual Basic.Net 2003 program. I can pull the report onto the form and it runs wonderfully. I want to make it run programatically with out prompting for the user to key in the parameters. I can supply them from an existing data file. I have tried many things but have lacked the solution.
How can I pass the parameters from VB.Net 2003 to the stored procedure which runs the Crystal Report with in the VB.Net 2003 program.
I appreciate all help and comments.
Can this be done or do I need to just re-write the report in VB.Net 2003?
Thanks,
Norman

Hi, Norman;
It sure is possible to pass parameters to a Stored Procedure via our .NET SDK.
Have a look at these samples:
https://www.sdn.sap.com/irj/boc/index?rid=/library/uuid/9043bbbc-ae66-2b10-ce96-b48f9e25a450
There are samples showing passing parameters.
Regards,
Jonathan

WIS 10901 error while refreshing report in rich client

I'm facing a strange issue while refreshing a report from Rich client. Here are details
Environment: BO XI 3.1 SP3, Oracle application DB. Weu2019ve 2 BO servers (S1 and S2) on cluster and load balancer (common URL) in front.
While login to S1 with 6400 port, I can refresh report in rich client.
While login to S2 on 6400 port or using common url, during refresh gives below error u2013
u201CA database error occurred. Database error text is: (CS) u201CDBDriver failed to load: C:\Program Files\.....\dbd_oci.dllu201D (The specified procedure canu2019t be found) (WIS 10901)u201D
Iu2019ve installed oracle8i client on my system. Any idea what causing this issue?

Yes. Oracle 10g client installed on both application server. I've teste the universe connection from server, it's working fine.
Any idea what could be probable causes of "DBDriver failed to load: C:\Program Files\.....\dbd_oci.dllu201D error?
One observation, the path of dbd_oci.dll is the BO installation directory of my local machine (on server BO is not installed on C drive). Why it's referring dbd_oci.dll from local client even in 3 tier mode?

I have a client that uses Windows that has recently told me she can no longer open the PDFs I send her. I can't find this elusive "Always Send Windows-Friendly Attachments" setting that I have read may solve my problem. Can someone get me there?

I have a client that uses Windows that has recently told me she can no longer open the PDFs I send her. I can't find this elusive "Always Send Windows-Friendly Attachments" setting that I have read may solve my problem. Can someone get me there?

Dear Dan,
It was from InDesign that I was creating the shared pdfs. I was one of two Mac drivers in a corporate sea of Win users and had to make the change I mentioned in order for the Win users to see my pdfs for review. The difference from what you appear to be doing was that were all on an MS Exchange Server so the files were shared over the company's Exchange Server e-mail system. However, some of these files occasionally went to outside users via regular e-mail and those people had no issues either.
So what I did was tested and worked for years.
You might look at the Adobe forums or Knowledge Base to see if that is a reported issue with newer version of CS. I was on CS2 when I was doing this, and the other Mac driver was on CS3 but had no problems either.
Some Win users I've talked to find a problem opening some pdfs (not mine) in general and found they had to open Reader first and them open the file from Reader's File menu. That most often happened if the client was using an outdated version of Reader.

Assigning AnyConnect Client Profiles based on the machine?

I have an ASA running 8.2.x code with AnyConnect 2.4.x.I have both Radius and LDAP (AD) AAA available.
If a user connects from a company owned laptop, I want to push down AnyConnect client ProfileA (with scripts to map drives etc...) and network ACL's set A.
If a user connects from any other computer, I want to push down AnyConnect client ProfileB (no scripts etc...) and network ACL's set B.
What I would like to do is CSD to do a machine certificate check (for presence of a cert from my private CA) and to assign a EndPoint Policy attribute (Managed on successful check or Unmanaged on failure). I can then use DAP to tailor the ACL's that get set.
It seems like the only way to handle AnyConnect client profiles is with Group-Policy. Using LDAP I can assign a user to a Group-Policy, but I have no way of determining is they are coming in from a company laptop or not when assigning the Group-Policy. DAP can not assign an AnyConnect client profile.
If at all possible, I do not users to have to pick a conenction profile or use different URL's.
Is there anyway to accomplish this?

Hi
Did you ever resolve this issue? I am trying to assign a specific IP address based on the hostname or machine cert but the certificate matching doesn't seem to look at the machine cert.
Has anyone got any idea how I could do this?
thanks
Steve

Anyconnect Client profile files deleted after client upgrade

L.S.
I am running anyconnect version 3.1.02040 on a Windows 7 64-bit machine with UAC turned on.
The ASA I am connecting to is a 5510 running ASA OS 8.4.5
The problem I have is the following:
We are using machine certificate authentication combined with RADIUS user authentication.
The machine certificates are stored in the Machine/Personal container in the local machine.
By default, the anyconnect client does not have the rights to access this certificate store when run by the user in non-elevated mode.
We do not want to have the user run the client as administrator (in elevated mode) all the time.
Therefor we have made an Anyconnect Client profile that sets the Certificate Store Override parameter to true and attached it to the group policy.
With this XML in place (in the C:\ProgramData\Cisco\Cisco AnyConnect Secure Mobility Client\Profile folder)
the users can connect to the ASA and authenticate using the certificate without the need for elevated rights. This is all working perfectly.
The anyconnect client and XML file are distributed to the clients using a software distribution system (Microsoft SCCM).
The problem happens when I update the Anyconnect package on the ASA. I recently updated the package to release 3.1.03103. This is what happens:
The user can connect using the 3.1.02040 client (certicate authentication works without elevation, since the XML Anyconnect Client Profile is present)
The Anyconnect software updates itself to the new version during the connection, pushed from the ASA.
The VPN is established.
However, the XML file that is associated with the group policy is deleted during the upgrade process and not placed back in the Profile folder on the client after the upgrade.
This means the user cannot connect without using elevated rights the next time he wants to connect.
If he uses elevated rights after the upgrade, the XML is pushed back from the ASA normally, allowing the user to connect without elevation again any subsequent times.
Is there any way to push the XML profile to the client from the ASA after the upgrade of the Anyconnect software?

Hi poiu720408 ,
1. You need to set up a web-url or group-alias under the group policy as web have enable the "tunnel-group-list enable" under the webvpn configuration. So once the user connect to the proper URL/alias the profile will be applied.
http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/98580-enable-group-dropdown.html
2. Yes the Anycopnnect store a "Cache " information on the PC , if you want to clan up you have to go to the anyconnect folder on C: on the PC and delete the global_preferences.xml profile.
3. This behavior is totally expected and they should disappear after a some minutes , however if you wan to force this , you can use the command "vpn-sessionsdb logoff webvpn noconfirm"
Please rate helpful post !
Hope this helps
- Randy -

AnyConnect client reconnects after 1 minute

AnyConnect client reconnects after 1 minute; WHY
version 3.1.02026
ASA:asa911-k8.bin
[25-4-2013 8:16:11] Establishing VPN session...
[25-4-2013 8:16:11] Checking for profile updates...
[25-4-2013 8:16:11] Checking for product updates...
[25-4-2013 8:16:11] Checking for customization updates...
[25-4-2013 8:16:11] Performing any required updates...
[25-4-2013 8:16:12] Establishing VPN session...
[25-4-2013 8:16:12] Establishing VPN - Initiating connection...
[25-4-2013 8:16:12] Establishing VPN - Examining system...
[25-4-2013 8:16:12] Establishing VPN - Activating VPN adapter...
[25-4-2013 8:16:15] Establishing VPN - Configuring system...
[25-4-2013 8:16:16] Establishing VPN...
[25-4-2013 8:16:16] Connected to my.vpn.com.
[25-4-2013 8:16:16] Connected to my.vpn.com.
[25-4-2013 8:17:19] Reconnecting to my.vpn.com...
[25-4-2013 8:17:19] Establishing VPN - Examining system...
[25-4-2013 8:17:24] Establishing VPN - Activating VPN adapter...
[25-4-2013 8:17:25] Establishing VPN - Configuring system...
[25-4-2013 8:17:25] Establishing VPN...
[25-4-2013 8:17:25] Connected to my.vpn.com.
[25-4-2013 8:17:25] Reconnecting to my.vpn.com...
[25-4-2013 8:17:25] Establishing VPN - Examining system...
[25-4-2013 8:17:25] Establishing VPN - Activating VPN adapter...
[25-4-2013 8:17:25] Establishing VPN - Configuring system...
[25-4-2013 8:17:25] Establishing VPN...
[25-4-2013 8:17:25] Connected to my.vpn.com.
[25-4-2013 8:16:11] Establishing VPN session...
[25-4-2013 8:16:11] Checking for profile updates...
[25-4-2013 8:16:11] Checking for product updates...
[25-4-2013 8:16:11] Checking for customization updates...
[25-4-2013 8:16:11] Performing any required updates...
[25-4-2013 8:16:12] Establishing VPN session...
[25-4-2013 8:16:12] Establishing VPN - Initiating connection...
[25-4-2013 8:16:12] Establishing VPN - Examining system...
[25-4-2013 8:16:12] Establishing VPN - Activating VPN adapter...
[25-4-2013 8:16:15] Establishing VPN - Configuring system...
[25-4-2013 8:16:16] Establishing VPN...
[25-4-2013 8:16:16] Connected to my.vpn.com.
[25-4-2013 8:16:16] Connected to my.vpn.com.
[25-4-2013 8:17:19] Reconnecting to my.vpn.com...
[25-4-2013 8:17:19] Establishing VPN - Examining system...
[25-4-2013 8:17:24] Establishing VPN - Activating VPN adapter...
[25-4-2013 8:17:25] Establishing VPN - Configuring system...
[25-4-2013 8:17:25] Establishing VPN...
[25-4-2013 8:17:25] Connected to my.vpn.com.
[25-4-2013 8:17:25] Reconnecting to my.vpn.com...
[25-4-2013 8:17:25] Establishing VPN - Examining system...
[25-4-2013 8:17:25] Establishing VPN - Activating VPN adapter...
[25-4-2013 8:17:25] Establishing VPN - Configuring system...
[25-4-2013 8:17:25] Establishing VPN...
[25-4-2013 8:17:25] Connected to my.vpn.com.

Hello Michael,
The problem here is because we cannot succesfully establish a DTLS tunnel. This could happen because:
- DTLS is blocked somewhere in the path
- A non-default DTLS port is being used
If DTLS is blocked in the middle the issue is because as of ASA Release 9.x and AnyConnect Release 3.x, an optimization has been introduced in the form of distinct Maximum Transition Units (MTUs) that are negotiated for TLS/DTLS between the client/ASA. Previously, the client derived a rough estimate MTU which covered both TLS/DTLS and was obviously less than optimal. Now, the ASA computes the encapsulation overhead for both TLS/DTLS and derives the MTU values accordingly.
As long as DTLS is enabled, the client applies the DTLS MTU (in this case 1418) on the VPN adapter (which is enabled before the DTLS tunnel is established and is needed for routes/filters enforcement), to ensure optimum performance. If the DTLS tunnel cannot be established or it is dropped at some point, the client fails over to TLS and adjusts the MTU on the virtual adapter (VA) to the TLS MTU value (this requires a session level reconnect).
In order to eliminate this visible transition of DTLS > TLS, you can configure a separate tunnel group for TLS only access for users that have trouble with the establishment of the DTLS tunnel (such as due to firewall restrictions).
1. The best option is to set the AnyConnect MTU value to be lower than the TLS MTU, which is then negotiated.
group-policy ac_users_group attributes
webvpn
anyconnect mtu 1300
This makes TLS and DTLS MTU values equal. Reconnections are not seen in this case.
2. The second option is to allow fragmentation.
group-policy ac_users_group attributes
webvpn
anyconnect ssl df-bit-ignore enable
With fragmentation, large packets (whose size exceeds the MTU value) can be fragmented and sent through the TLS tunnel.
3. The third option is to set the Maximum Segment Size (MSS) to 1460 as follows:
sysopt conn tcpmss 1460
In this case, the TLS MTU will be 1427 (RC4/SHA1) which is larger than the DTLS MTU 1418 (AES/SHA1/LZS). This should resolve the issue with TCP from the ASA to the AnyConnect client (thanks to MSS), but large UDP traffic from the ASA to the AnyConnect client might suffer from this as it will be dropped by the AnyConnect client due to the lower AnyConnect client MTU 1418. If sysopt conn tcpmss is modified, it might affect other features such as LAN-to-LAN (L2L) IPSec VPN tunnels.
If DTLS is not blocked in the middle another potential cause for the DTLS failure that DTLS is configured on a non-default port after the WebVPN is enabled (for example, when the webvpn enable outside command is entered). This is due to Cisco bug ID CSCuh61321 and has been seen in Release 9.x where the ASA pushes the non-default port to the client, but continues to listen to the default port. Consequently, the DTLS is not built and AnyConnect reconnects.
The workaround for this problem is:
Disable the WebVPN.
Enter the DTLS port.
Enable the WebVPN.
Regards,
-Gustavo Medina

File Transfer From Unix server to Windows Client System Using WebUtil

Hi all,
I want to Transfer a File from Unix Server to Window Client System using Webutil. But below mention code is not working.
DECLARE
     V_Server_Path VARCHAR2(500) := Null;
     V_Client_Path VARCHAR2(500) := Null;
BEGIN
     V_Server_Path := '/proj/oraapps/viper/dev/reports/cache/Saveauftr.txt';
     V_Client_Path := 'C:\Migration\EU_Applications\Lima\OAS_WorkArea\Client\Saveauftr.txt';
     IF WebUtil_File_Transfer.Is_AS_Readable(V_Server_Path) THEN
     IF WebUtil_File_Transfer.AS_To_Client(V_Client_Path,V_Server_Path) THEN
          Message('Downloading the File ..... .... ... .. .');
          Message('Downloading Was Successfull ...');
          Message('File Transfer from Server Was Successfull ...');
     END IF;
END IF;
END;
Can anyone suggest me,Why the above code is not working and what to do for solve the Problem.
Regards
Gany

Hello,
You have more chances to get an answer in the Oracle Forms OTN Forum :
Forms
Regards

ISE 1.2 Posture Assessment with AnyConnect Client

Hi Experts,
I need clarity for posture assessment with AnyConnect client. I understood that we had traditional NAC agent with ISE 1.1.
Since new Anyconnect version 4 has come which is used for ISE 1.3 posture assessment however I am not sure if I can use Anyconnect 4 with ISE 1.2 ? Can you please put light on this ?
if not , do I need to upgrade to ISE 1.3 ? what is the process to upgrade to ISE 1.3 ?
Thanks in advance

ISE can provision clients with agent and configure agent profiles.You have Client-provisioning policies that enable users to download and install resources on client devices.(Windows and Mac OS X NAC Agents, Cisco NAC Web Agent.

Pull a report of Anyconnect clients in use

Similar Messages

Maybe you are looking for