PXE-Boot with Hyper-V based on W2K12 R2 with Gen2-VMs

Dear Community,
as you probably know the new R2-Version was advertised with the ability of PxE-booting with the synthetic instead of the legacy-nic which works with poor 100 mbit/s.
Here´s the problem:
When I create a new virtual machine with Gen2 without the option "Secure Boot" and PxE-boot it, I get the following error:
Boot failed. EFI Network.
Boot failed. EFI SCSI Device.
No Operating System was Loaded. Press a key to retry the boot sequence
When I create another new virtual machine with Gen2 but with the option "Secure Boot" and PxE-boot it, I get this error:
Station IP address is x.x.x.x
Server IP address is x.x.x.x
NBP filename is pxelinux.0
NBP filesize is 15888 Bytes
Downloading NBP file...
Successfully downloaded NBP file.
Boot Failed. EFI Network. Failed Secure Boot Verification.
Boot Failed. EFI SCSI Device
No Operating System was Loaded. Press a key to retry the boot sequence
When taking a look at the log of the TFTP-Server (TFTPD32) I get the same information regardless which way I do it. The only interesting thing it says is:
"Peer returns ERROR <User aborted the transfer> ->aborting transfer"
I have also tried to use another tool called Serva as TFTP/PXE-Server -> The error still occurs.
Before anybody wants me to try to do it as Gen1 -> I know that this works, but I want to get it running under Gen2 since the synthetic one works (should work) much faster than the legacy-one.
Really looking forward to get some useful information here.
Thanks in advance !

This question was completely answered by Andy here:
http://social.technet.microsoft.com/Forums/en-US/winserverhyperv/thread/4098e57f-c6da-493a-a772-87d60ee1d0a1/#b2808adb-a79e-49e6-8a00-2c324c3e41d1
He wrote:
"Apparently, there is an issue in WDS that causes it to use legacy NetBIOS name resolution instead of DNS to find a domain controller, and it impedes domain controller connectivity. The solution is simple - go to TCP advanced properties on WDS server,
and on WINS tab disable NetBIOS over TCP/IP. This forces WDS to use the right name resolution, and everything works perfectly."
I can confirm it. Works perfectly! Thanks to Andy!
Vadim

Similar Messages

PXE Boot a Hyper V Guest - Not receiving a DHCP IP Address

Hello Everyone,
I am trying to PXE boot a Hyper V guest, but am not getting a DHCP IP Address. Eventually the DHCP query times out and loads into the guest OS I have manually installed. See the PXE Boot Screen below. When in the installed guest OS, I do receive
a DHCP IP address as shown below. I am utilizing the Legacy Network Driver. I don't think it is related to VLAN identifier, but tried with/without and still no go. Any ideas what could be preventing this? Please let me know.
PXE Boot Screen:
CLIENT MAC ADDR: 00 15 5D F2 99 0C GUID: B366BBA1-D503-4D64-A77E-77474F3A2193
DHCP.........-
PXE-E51: No DHCP or proxyDHCP offers were received.
DHCP IPCONFIG in Guest OS:
Ethernet adapter Local Area Connection:
   Connection-specific DNS Suffix . : mywork.com
   IPv4 Address. . . . . . . . . . . : 10.242.242.251
   Subnet Mask . . . . . . . . . . . : 255.255.255.128
   Default Gateway . . . . . . . . . : 10.242.242.129
Thanks,
Ron

Hi Ron,
A solution is provided in this thread. You may need to have a look on the steps below:
• PXE-E51: No DHCP or proxyDHCP offers were received.
The client did not receive any valid DHCP, BOOTP or proxyDHCP offers. To resolve this issue, check each of the following network configuration items:
DHCP services are not available on the network to which the PXE-enabled NIC is connected.
A DHCP proxy or IP helper address is not configured for the subnet on which the PXE client is connected.
The switch port connected to the PXE NIC is running Spanning Tree Protocol, EtherChannel Protocol, or Port Aggregation Protocol and is thus not activated immediately when a link is detected. This forces the DHCP request from the PXE client to timeout.
DHCP is available on the network, but PXE is not.
The network cable is not attached to the PXE-enabled NIC on the target server.
See: http://social.technet.microsoft.com/Forums/en-US/d06413a4-af2b-4736-a510-c0a68eb880cf/cannot-get-certain-machines-to-pxe-boot
TechNet Subscriber Support in forum |If you have any feedback on our support, please contact [email protected]

"Error: Document not found (WWC-46000)" with a form based on a table with blob item

Hi all,
I have to manage a table-based form. One of the fields of the table is BLOB and the corrisponding field of the form is HIDDEN.
When I push the INSERT button all works well but when I try to UPDATE I get "Error: Document not found. (WWC-46000)".
Have you some suggestions ?
Thanks,
Antonino
p.s. Oracle Portal 3.0.7.6.2 / NT
null

Sorry, I think I did not explain well my problem.
Imagine this simple table:
key number;
description varchar2(50);
image blob;
I need to make a form that contains the corresponding "key" field and the "description" field but not the "image" one. I don't want to allow the end user to upload images!
When I insert a row the form works well and in the "image" field of the table an empty blob or null (now I don't remember) is stored: that's ok.
Now imagine I want to change the value of the "description" field. I submit a query for the right key, I type a new value for the description and finally I push UPDATE button but....an error occours.
I think this error is related with the Blob item of the table but I'm not sure.
Thanks again,
Antonino
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Dmitry Nonkin([email protected]):
Antonino,
If I understood the problem correctly:
The form's item type for BLOB column used to upload content cannot be hidden, that's why we have a special item type FileUpload(binary).
Thanks,
Dmitry<HR></BLOCKQUOTE>
null

Windows Deployment Services Unable to PXE boot clients PXE-E53: No Boot Filename Received

Hi
I'm trying to configure WDS/MDT to deploy Windows 8.1. I've captured an image and I'm ready to deploy the image to a workstation, as per the above title when I attempt to PXE boot a test workstation it just times out with the following error message PXE-E52:No
Boot Filename Recieved. I've tried a few tweaks to get it working however no such luck.
The setup is as follows it's a virtual Windows 2012 R2 machine, just a fresh member server with microsoft deployment toolkit installed and WDS role installed with the nesscary framework features installed.
I've tried tweaking the properties of most of the settings within the server settings in WDS with no such luck.
I'm a novice at WDS but from what I've read I shouldn't need configure that much in the first place to get it working.
I'm willing to bet it will be something I've overlooked so I need a 2nd opinon, could anyone provide any troubleshooting tips. If you require anymore information please let me know.
Cheers

Hi Joel,
This error may caused by the WDS server is not pushing the images because PXE Clients are not able to download or communicate with the TFTP server.
The image can’t be download generally caused by the the Vlan is not enabled IP helper/DHCP relay agent configured on it, all DHCP broadcasts on UDP port 67 by client computers
should be forwarded directly to both the DHCP server and the Windows Deployment Services PXE server.
The related KB:
PXE clients computers do not start when you configure the Dynamic Host Configuration Protocol server to use options 60, 66, 67
http://support.microsoft.com/kb/259670
The similar thread:
PXE-E53: No boot filename received
http://social.technet.microsoft.com/Forums/systemcenter/en-US/8de3bd6a-f8ec-41d9-ae0f-5b2fdb9e5831/pxee53-no-boot-filename-recieved?forum=configmgrosd
WDSServer (Windows Deployment Server) Fails to Start
http://social.microsoft.com/Forums/en-US/d96b0b86-f2b0-49a5-8946-19ab515f23e6/wdsserver-windows-deployment-server-fails-to-start?forum=windowshpcitpros
I’m glad to be of help to you!
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Does Boot Camp Support PXE Booting?

I have a Mac pro Quad Xeon, 8gb ram, 3 Drives (multiple sizes)
I want to PXE boot one of the drives to image it with Vista, is this a possible to do this w/ boot camp? If so I cannot figure it out.

Hi and welcome to Discussions,
maybe this thread can help you: http://discussions.apple.com/thread.jspa?messageID=7104286
Regards
Stefan

PXE Boot With intel Based IMAC

Hello,
I am trying to boot my IMAC from the network with PXE Boot with no success.
I found some documents (very little) about how to boot mac from network using diffrent mac with app called netboot, but i assume that because my imac is intel based it should be able to boot from PXE.
Are there any documents information you could point me to ?
Thanks.

U.S. websites for those companies don't show those models on their product lists or at support. If your iMac recognizes your printer, don't worry about the driver, it's there.

Type 2 Virtual Machine in Hyper-V will not PXE boot with WDS

Hi
Bit of a wierd scenario this but I'm doing a bit of a lab experiment kind of thing. The setup is as follows:
VMWare Workstation 10 with Windows Server 2012 R2 running as a virtual machine. In VMW10 I have a NAT network interface and a Bridging interface set to load with the virtual machine. These seem to work fine (although the NAT doesn't seem to want to connect
to the internet but that's why the bridging one is there in addition).
Server 2012 is configured with the following roles:
ADDS, DHCP, DNS, Hyper-V, Printer, WDS
I have correctly configured WDS to work on the same machine as DHCP and I can get PXE boot working with WDS on a Type1 Virtual Machine in Hyper-V using the Legacy Network adapter. My problem is when I try and PXE boot on a Type2 Virtual Machine (this type
is new in R2 and should eliminate the need for a legacy network adapter) using the same network interface that I used for the Type1 machine, I get an IP address from DHCP but WDS doesn't seem to respond. Instead I get the "PXE-E16: No Offer Received"
message. I have tried just about everything I can think of and spent the whole day trying to figure out why this is the case but came up with nothing. Has anyone else encountered this or can anyone shed any light on the matter?
Many thanks in advance

"VMWare Workstation 10 with Windows Server 2012 R2"and "Server 2012 is configured with the following roles: ADDS, DHCP, DNS, Hyper-V, Printer, WDS"
Hyper-V is not supported to be run as a VM. It is a Type 1 hypervisor, which means it works on the bare metal. You have it running as a VM on a Type-2 hypervisor, so it has no access to the bare metal. Yes, VMware may have made it so some
things work in that environment, but it is not a supported (or tested) environment for Hyper-V.
.:|:.:|:. tim

Formatting the encrypted hard drive or intalling OS again with PXE boot can change TPM owner password file?

Hello,
1) I realized that when MBAM bitlocker encryption start both Recovery key and TPM owner password file are send to MBAM server. If we change the computername of the notebook, we can find out Recovery key from MBAM server with the KeyID as we can read it from
computer screen, but we can not find out TPM owner password file with the existing new computername information from MBAM server, so we have to know old names of all computers but it is impossible. So we have to do decryption and clearing TPM than we
can again encrypted it with its new name. is it right?
2) We will going to deploy mbam encryption to our notebooks. But sometimes when a person quit the job his notebook can given to another person or new employee and based to our procedure when a notebook will given to another user it should installed
OS again with PXE boot. I would to know will it be enough to installing with this method again with a diffrent computer name or should I firstly clear its TPM than install OS with PXE to keep TPM owner password file missing as item 1?
I hope i can explain what i mean :)
Regards,
SibelM

I would suggest you to first decrypt the laptop and then follow the process:-
- Clear the TPM
- Encrypt the type.
- Check for the encryption behavior.
Cause I have found on some model that if the OS drive is encrypted, PXE boot fail on that machine even though I also did a direct PXE on an encrypted machine with clearing the TPM.
TPM ownership password is a hash file that gets generated with a set of algorithm. SO each time when you PXE boot, by clearing the TPM, the TPM hash password for the TPM will change. This has been done for security measures.
Gaurav Ranjan

Server 2008 configured for PXE boot with UIU and GhostCast

Right now, I am in the process of switching over from UIU 4, to UIU 5, and the implementation is completely different. We used GhostCast to push images out before, but the new UIU uses WIM files to pull the drivers off the server. I had a few
questions about reconfiguring the new server.
Currently, we have a server 2003 machine running ghost cast. It pulls its images off of a server 2008 machine. The server 2008 machine can be accessed remotely. So my first question is, can this be configured to allow remote connections
with the new setup?
The things I have been reading have said that you need to enable DNS, AD, and DHCP, however if we connect this to a WAN, will it conflict with that? Or can we configure only one of the ethernet ports to see this? Sorry kind of new to this.
I guess my main concern is, can we set up a separate domain for GhostCasting, while still being connected to an external domain?

Hi,
I’m not sure what you really want to do. For PXE boot, I think DHCP is always required just like Microsoft deployment solution WDS and MDT.
The two products are third products, so I don’t know the detail information about how they work. Based on my experience, they should be based on broadcast or multicast.
If so it could be a bad idea if you install it on a server facing the internet.
I think you can also ask in the third party forums that provide the products.
Thanks for understanding.

PXE boot tablet with Used USB dongle

We are running SCCM 2012 R2 Single Primary Site Server.
We are using the dongle (USB) to PXE boot the tablet computer.
We have advertised the Task Sequence to All Unknown Computer.
Once we use the USB dongle to image computer 1 , then the MAC address of USB dongle gets associated with the computer name of the tablet because the tablet does not have Ethernet port.
Now to image computer 2 if we PXE boot with used dongle gets PXE abort as it is known computer.
If we advertise to "All Known" computers then try the PXE boot works and we can image computer2 .
Now how can we advertise task sequence to "All Unknown" computers and get the task sequence to work with used USB Dongle.

I suggest going back and reading it again then.
Highlight:
A “better” solution could be to create a collection, that is based on the Mac Address of the devices, which are used to deploy those systems. So typically this collection will have a handful of Mac Addresses. Important part is, that those Mac addresses
shouldn’t be used in day to day business, just for the plain purpose of deployment. Then one can advertise as many task sequences as required and limit the deployment(s) to only media and PXE. This way, the deployment isn’t visible from the Software Center
but the support staff can continue to deploy new systems using PXE or other medias like USB Sticks.
Don't retire TechNet! -
(Don't give up yet - 12,830+ strong and growing)

OSD to Surface fails to PXE Boot and returns PXEGetPXEData Failed with 0x80004005

Scenario: When trying to Image Windows 8.1 to a Surface Pro, Surface Pro 2 and Surface Pro 3 I have downloaded the latest Surface Firmware and Drivers (August 18th 2014 I believe), the NIC's are in the x64 PXE Boot Image. I have verified that no DHCP Option
67 is set, and that SpanningTree PortFast is enabled. All other Images function correctly, Windows 7 Sp1 works. We use the Microsoft USB NIC, and we PXE boot and download the PXE Image fine, then it comes into windows and goes to detect the NIC, at which point
it fails and reboots.
The Surface has had Firmware update on it to the latest.
It appears the NIC just stops working, which makes me think that the latest Driver pack for Surface does not contain the PXE boot versions for their NIC.
Trying the Docking Station (which utilizes NIC ASIX AX888772) exhibits the same problem.
The NIC stays active until the OSD Screen comes up, it fails trying to load the Surface NIC though (or the NICs in the Driver pack they just released do not include a PXE Boot Driver...the Drivers once imported do not show any as being Boot Critical...which
make me think this is the case even more so.
Doing a USB PXE Boot also fails to load the NIC.
Going to F8 and doing IPCONFIG /RENEW verifies the NIC is not active.
I see tons of postings on the Surface being a nightmare to image.
Errors:
Failed to Download pxe variable file. Code (0x0000001)
PXEGetPXEData Failed with 0x80004005
Anybody having any other experiences out there, or have anything else they could think to try?
David Baur

(or the NICs in the Driver pack they just released do not include a PXE Boot Driver...the Drivers once imported do not show any as being Boot Critical...which make me think this is the case even more so.
There are no "PXE boot versions" of drivers at all. What you described just indicates that there is no driver in winpe that matches the hardware. WinPe is based on the respective version of the full os so you have to add Win8.x drivers to the boot image.
The architecture also has to match. Have you added NIC drivers to the boot image at all?
NIC drivers are never boot critical if I am not mistaken.
Torsten Meringer | http://www.mssccmfaq.de

After PXE boot to machine nothing shows up. Blank SCCM page with no option to install OS images.

I am working on using PXE with SCCM 2012 and finally got my test VM to boot with the standard x86 boot image. This is the process:
1. Start up VM with no OS
2. Contacts SCCM and I press F12 to Network Boot
3. Boots into a SCCM screen and says " Windows is starting up" then " Preparing Network Connections".
4. Then all i see is a blank screen. After about a minute it will just reboot.
I found this post that discusses adding the drivers need for the boot images:
http://social.technet.microsoft.com/Forums/en-US/fd96466b-0521-48d8-b31e-4477468982fe/sccm-pxe-boot-initiated-but-nothing-happens-after-that?forum=configmgrosd
I added the entire VMware tools Driver folder to both my boot images. (All it had in there was a SCSI adapter)
Tried to redo the PXE and still get the same menages with the blank screen after that.
What am I missing here?

Sounds like your boot image is missing network drivers...
Couple of checks though:
If the VM in case has already been introduced somehow to ConfigMgr, check Devices -node from the console and search for "Unknown", if there are objects named "Unknown" (not the default x86 or x64 objects!), delete them
Add command line support (F8) to your boot image
Boot your VM, as soon as you get in to WinPE, hit F8 to open command prompt
Run ipconfig to see if the VM get's IP address
If the VM doesn't get IP address, you probably don't have the correct network driver in your boot image. You can obtain the correct driver by installing OS (the same architecture as you boot image, and based on the same FullOS of your boot image, ConfigMgr
2012 RTM=WinPE3.1=Windows 7, SP1=WinPE4.0=Windows 8, R2=WinPE5.0=Windows 8.1) on to your VMware VM and then use this tool:
http://gallery.technet.microsoft.com/ConfigMgr-Driver-Injector-aae7d17d to capture the needed drivers. Then you can import those drivers to ConfigMgr, categorize them and add the LAN and SCSI drivers to your boot image.

PXE Boot with UEFI. WDS not sending WinPE wim

I am trying to test PXE booting on devices that only have UEFI and no CSM support.
We are running Windows Server 2008 R2 in our environment.
On the DHCP server, we have option 66 and 67 set. If I change option 67 to SMSBoot\x86\wdsnbp.com and boot a traditional BIOS system (non UEFI) the SCCM server responds and gives me the option to hit F12 and PXE boot. This works without issue and can deploy
images.
I then change option 67 to SMSBoot\x64\wdsmgfw.efi and use a machine that is pure UEFI (meaning UEFI without any legacy support / CSM). The system appears to successfully download the wdsmgfw.efi and font file via TFTP as shown in the WDS logs. However, it
then goes to the next sreen where it is trying to contact the WDS server. AFter retrying for a while it will error out with error 0x102 which I believe translates to ERROR_TIMEOUT
The SMSPXE.log repeats the following:
Client boot action reply: <ClientIDReply><Identification Unknown="0" ItemKey="2046820352" ServerName="" ServerRemoteName=""><Machine><ClientID>8908f9c4-c345-49ba-b137-af7b0b983584</ClientID><NetbiosName/></Machine></Identification><PXEBootAction
LastPXEAdvertisementID="" LastPXEAdvertisementTime="" OfferID="GAS20043" OfferIDTime="7/24/2013 3:12:00 PM" PkgID="GAS00037" PackageVersion="" PackagePath="<a href="http:///SMS_DP_SMSPKG$/GAS00038">http://<IVE
REMOVED THIS>/SMS_DP_SMSPKG$/GAS00038" BootImageID="GAS00038" Mandatory="0"/></ClientIDReply>
SMSPXE 7/24/2013 7:14:58 PM 7724 (0x1E2C)
00:50:56:01:00:82, DF6A0C42-F909-B518-7B44-3150B662200B: found optional advertisement GAS20043 SMSPXE 7/24/2013 7:14:58 PM 7724 (0x1E2C)
Looking for bootImage GAS00038 SMSPXE 7/24/2013 7:14:58 PM 7724 (0x1E2C)
Any idea what may be going on?

Hey,
I am having the following situation:
DP1 = Windows Server 2008 R2 SP1 (Standalone Primary Site Server SCCM 2012 SP1 CU2)
DP2 = Windows Server 2012
UEFI Client: Microsoft Surface Pro (with Microsoft Surface Network Adapter)
BIOS Client: HyperV Virtual machine with Legacy network adapert
DP1; DP2 and DHCPServer all in Subnet1.
(IP Helper is set for DHCPServer for DHCP and for DP1 & DP2 for DHCP and BootP - I checked serveral times if everything is right here)
UEFI Client and BIOS Client in Subnet2.
Situation1 -- Using no DHCP Options and both DPs(DP1 and DP2) WDS running:
UEFI Client - Boots perfectly (contacting Server DP2)
BIOS Client - Boots perfectly (contacting Server DP2)
Situaion2 -- Using no DHCP Options and WDS just running on DP1:
UEFI Client - Does not boot (no error information is provided)
BIOS Client - Does not boot (no Bootfilename recieved)
Situation3 -- Using DHCP Options(Option 66="IP of DP1" Option 67="SMSBoot\x86\wdsnbp.com") and WDS just running on DP1:
UEFI Client - Does not boot (no error information is provided)
BIOS Client - Boots perfectly (contacting Server DP1)
Situation4 -- Using DHCP Options(Option 60="PXEClient" Option 66="IP of DP1" Option 67="SMSBoot\x86\wdsnbp.com") and WDS just running on DP1:
UEFI Client - Boots perfectly (contacting Server DP1)
BIOS Client - Does not boot (taking hours to recieve dhcp options..)
My problem is i am having a lot of location with 2008 R2 SP1 server only (this is why situation 1 is not enough for me :-( ).
Based on this article:
http://ccmexec.com/2013/05/configmgr-2012-uefi-and-pxe-boot-support/
x64 UEFI Devices should work with Server 2008 R2 SP1 (not only Server 2012).
Interesting is I am having ALL files on Server 2008 R2 SP1 like they are on Server 2012 (in SMSBoot\x86 folder, too!)??
Some more ideas?
Thank you for help

PXE boot issue with DHCP and SCCM server on different subnets

I'm working with a client on the operating system deployment module of SCCM.
Their network configuration currently has a single large subnet for client
computers with a DHCP server on the same subnet. The SCCM subnet is
configured on a seperate subnet with no DHCP server on the subnet. We want to
configure client computers to be able to boot using the PXE client to deploy
OS images to the machines but can not get PXE-boot to work correctly.
Also, the client does not want to make changes to their network
infrastructure routers or switches to remedy this problem. Are there settings
on the DHCP or SCCM servers we can implement to make this work? If so, what
needs to be installed or configured on each server. We currently already have
WDS installed on the SCCM server and the SCCM server is configured as a PXE
Service Point within SCCM. Both WDS and the PXE Service Point seem to be working fine.
Any help would be appreciated.
Thanks,
Gary

I am Brazilian,
sorry for wrong english
My DHCP is on linux,
in my own structure VLANS
The system center is on the network
10.0.4.0/24
The machines on the network 10.0.5.0/24
The problem is that the machines that
are not on the same network system center
can not boot
I tried configuring / etc/dhcp3/dhcpd.conf
follows
option vendor-class-identifier "PXEClient";
option bootfile-name "\
\ SMSBOOT \ \ x86 \
\ wdsnbp.com";
option tftp-server-name
"10.0.4.101"; ---->
IP server
But it did not work, anyone know
how to configure?

PXE-Boot with Linux

I have an IBM Machine (8193-75G) with Intel 10/100/1000 LAN. Is it
possible to do an PXE-Boot with Linux? Do I need a special driver?
Thanx

[email protected]
> I have an IBM Machine (8193-75G) with Intel 10/100/1000 LAN. Is it > possible to do an PXE-Boot with Linux? Do I need a special driver?
> Thanx
You might get an answer in the imaging forum
Jared L Jennings, CNE
Novell Support Forums SysOp.
http://support.novell.com/forums/faq_nntp.html
Posting with XanaNews Reader 1.15.7.4
Geek by Nature, NetWare by Choice.

PXE-Boot with Hyper-V based on W2K12 R2 with Gen2-VMs

Similar Messages

Maybe you are looking for