QoS: Multiple acl entries cannot be used in match-any in class Match_XY

Hello All,
I'm getting below error while trying to add the two extended ACL in the class-map for classifying the traffic. Is there any way I can add two extenteded ACL in the same class-map for classifying the traffic.
Error log: "QoS: Multiple acl entries cannot be used in match-any in class Tag_AF13"
device details: cisco WS-C6506-E with Supervisor Engine 2T
IOS version -s2t54-adventerprisek9-mz.SPA.150-1.SY1.bin
R1(config)#class-map match-any Tag_AF13
#match access-group name XX
#match access-group name XY
QoS: Multiple acl entries cannot be used in match-any in class Tag_AF13
Regards,
Thiyagu

Hi Rajan,
Thats because of the logic used for ACl operations, as per your config you are class-map match-any. The match any argument says that the class map must match either of the two arguments supplied.So lets take a look at how the sequence of operations of how this will be interpreted by your class map.
1> Any particular packet will be first matched against the first ACL "XX".
2> Suppose there are 10 entries there if it matches any of those entries the appropriate action will be talen.
3> If none of those entried match the packet there will be an implicit deny at the end of the ACL( default behaviour of ACL's)
4> In that case the packet will match the implicit deny and will get dropped.
5> The packet will under no circumstances go to the next ACL "XY"
Thats the reason multiple ACL's aren't allowed by the IOS.
You can try to collate both ACL's and put them in just one ACL that should work well. If you need help please pots both the ACL's.
Please do let me know if you have any further questions
HTH
Regards
Umesh

Similar Messages

  • This is not really a question but just a highlight. I have been for 20 minutes on the phone through the express lane support and I have been told that iCloud DO NOT stores music or video and cannot be used to pushes any music you bought through iTunes !

    I have been amazed from the Express Lane support. I have been asking information about how to store/push my iTunes music in the iCloud. The answer has been that iCloud DO NOT stores you iTunes music at all !!!!! Is this real ?
    I am Mobileme user since the beginning and just bought OS X Lion and all necessary software to maximise the use of iCloud and now I have to discover that what has been advertised for months on the web is just ballsheets.

    Wow!  It took you 3 week to come up with that ridiculous response?
    Since I don't have access to the 11/13 web pages (my time machine is out of order), I can't provide that.  However you know full well that iTunes Match has been live for the last 3 weeks, and it isn't "ballsheets."
    As far as the "gift you may have to spend too much time on internet", it took you far longer to compose and post your whining rant that it would have if you just searched it with Google and got your own answer...

  • Sap.ui.table.Table.addRow(): The control manages the rows aggregation. The method "addRow" cannot be used programmatically!

    Hi there,
    I'm using a sap.ui.table.Table and want to add rows. However, I get the error message stated above in the title of this thread.
    The same happens when adding the rows via XML view by defining the rows aggregation.
    Coding in Table-dbg.js
    * @see JSDoc generated by SAPUI5 control API generator
    sap.ui.table.Table.prototype.addRow = function() {
      jQuery.sap.log.error("The control manages the rows aggregation. The method \"addRow\" cannot be used programmatically!");
    Any ideas?
    Regards
    Tobias

    Hi Tobias,
    A row could be added to the model instead.
    Below post might help.
    Re: Adding 1 row to a table in SAPUI5 with local data(textfields etc...)
    Thanks and Regards, Venkatesh

  • Clients cannot connect using afp running lion 10.7.1, worked ok before upgrade from 10.7 to 10.7.1

    I am running a macminiserver on ahome newtwork.  Original running snow leopard and then upgraded to 10.7 lion on all machine and everything was working fine.  Clients coul connected to shared drives on the server using afp.  However, after upgrading to 10.7.1 on the server and client machines, they can no lnger connect to the drives using afp, however you can connect using smb.
    I ahve tried stopping and starting the afp server, rebuilding permissions on the server - still cannot connect using afp.
    Any ideas?

    Be sure the correct Lion afp port is open on your router, even if you are using an Airport (port 548 tcp). Just do a search on "Mac OS X Lion ports".
    Also, if this is outside of the network, use the full server name in the Finder's Connect to Server, afp://server.com; when it prompts for a username, enter your first name and last name (not your short name) and then you also need to enter your password. If you don't have a fqdn, then you can use the static ip for "server.com"
    It should work, working for me inside and outside of the network. Admittedly, I don't think you need the port on the router for internal use, but you can test both ways.
    When working outside of the network a vpn is not required.

  • OHW Search always uses match any words option

    I've generated an ohw project which includes a search index. It matches search topics using the "match any words" option no matter which option I choose. The other options ("match all words" and "boolean expression") work fine when I use RoboHelp to view the help project. Are these supported options for ohw?

    Hi, David. We're aware of the problem with the OHW search--it should be fixed in the next OHW release, which will hopefully be available on OTN within a few weeks.
    Ryan

  • I have an MX 510 printer. I want to scan multiple pages. Cannot use doc feed as scanning booklet.

    I have an MX 510 printer. I want to scan multiple pages. Cannot use doc feed as scanning booklet. How do I do this?

    use the MP Navigator application
    When it opens choose PDF and then select Multiple Pages.
    John Hoffman
    Conway, NH
    1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

  • Export multiple response entries to combine PDF.

    Is it possible to export multiple response entries into a singe multi-page (combined PDF?  This can be done externally using Adobe Acrobat Pro, but it would be extremely useful for distributing responses to clients especially since some cannot access the responses through mobile devices such as IPAD.

    Sorry, we currently don't support this. You have to export them one at a time.

  • Hyperion Smart Cut Session Issue streaming multiple reports at a time using

    This is a lengthly post with details, Please review with Patience:
    We are trying to integrate Workspace based web Analysis reports within our intranet portal, thru portlets (made from individual workspace smartcut link), so that users can customize their page as needed, Once they login thru intranet, Cookie is set and passed to succeeding smart cut links via secured http headers. This part is fine, but mainly running into issue with streaming several multiple web-analysis reports at a time,+ we are using Iframe to display and stream multiple individual reports on to one page, but unfortunately all Iframes are sharing one session rather than creating individual session, mostly because of limitation of current web analysis system architecture and IE browser behavior with sessions .
    Which Hyperion reporting tool does allow to stream multiple reports  at a time? ideally we want to create Iframe of each workspace report so that users can customize and pick portlets as needed. To stream multiple reports at a time.
    Problem Description: Hypeiron Web Analsysis, Smart cut reports incorrectly rendering images and intermixing dash boards on POV changes upon multiple reports being diplayed at one time thru Iframe's, issue seem to mostly relate to Hyperion using single session rather to multiple session when displaying several web reports at a time.
    Steps Needed To Reproduce:
    User logs into workspace.
    user click on expolore and able to view the report without any issues.
    When right on any of the report and select properties.
    Select the SmartCut url and paste it in the Internet explorer.
    The webanalysis report opens without any issues.
    Similarly user copies the smartcut url for a different report and paste the link on a different tab or new window of same browser.
    The report on the first tab gets over written of the report of the second tab of the browser.
    The issue happens when two different reports and opened on a browser with multiple tabs. The reports get over written.
    Oracle development answer:
    In the described scenario opening new browser window does not spawn a separate independent browser session. A new browser window is supplied with URL pointing to the same domain, so all browser cookies including the "ORA_WA_SID" (WA session cookie) are shared between the windows. But multiple application instances cannot run in the same browser session simultaneously because of session sharing. This is not actually a defect, but rather a limitation of current system architecture and browser behavior. And there is no way to fix it programmatically on the product side.

    Hi MeHyper,
    Your current arrangement puts most of the session handling and persistence on the client. This forces you to accept whatever the client decides to persist and propogate between browser elements (in this case iframes).
    My approach would be to:
    Consider coding your portlets to manage the sessions. Manage using a somewhat stateless strategy so that each request to the server requires a login and connect, retrieve, and disconnect. Each Iframe should access a different portlet url (or provide a different query) based on its content.
    This way, in theory, you can invalidate the sessions and related cookies and update the various report elements independently.
    Is smartview out of the question here?
    Regards,
    Robb Salzmann

  • "Apple ID cannot be used for MobileMe" when setting up Find My iPhone app

    Okay, folks, spent some time with MobileMe support via chat this morning. This is what I've learned. Apparently you CANNOT use an Apple ID, regardless of what format it's in (usually a full email address) AS LONG AS IT'S ASSOCIATED WITH A MOBILE ME (ME.COM ADDRESS) ACCOUNT THAT IS CLOSED OR NO LONGER ACTIVE. Unfortunately, there is no way to disassociate the two and there is no way the old MobileMe (me.com address) account can be deleted.
    Apparently, I had some issue when I was trying out the MobileMe for the trial period many months ago and for some reason couldn't use my primary Apple ID (my primary email address), so I created a me.com address for the MobileMe account. Eventually, I cancelled the MobileMe account because the cost wasn't justified for the features it offered. Unfortunately, that association with my primary Apple ID is permanent and THAT is the source of the "This Apple ID canot be used for MobileMe" error. Or at least that's ONE reason for it.
    The solution? Create a completely new, separate Apple ID using a valid email address from which you can receive a verification email. The address is NOT used to receive any further emails from Apple. Only to create logon credentials. Do NOT associate this email address with your current/primary Apple ID or any other Apple ID. This is what you use to set up Find My iPhone/iPad, etc. using the MobileMe setup in Settings>Mail/Contacts/Calendars as well as the Find My iPhone App (plus it's your logon to the MobileMe Find My iPhone web page).
    When you log in to the MobileMe page, BE CAREFUL WHEN YOU ENTER YOUR APPLE ID IF IT'S A FULL EMAIL ADDRESS: apparently, the ID field automatically tries to change it to "[email protected]" instead of your "[email protected]". Just check it before and after you enter your Apple ID password and submit.
    I did this and it works. Find My iPhone app and service works beautifully. Spotted my iPad right where I'm at on a map. I sent a message to my iPad via the service (which also offers the option to play a sound, lock the device or even wipe the device).
    I hope this information helps SOMEONE.
    Oh...interesting footnote: I was informed that APPLE IDs CANNOT BE DELETED. Even if you create a "test" Apple ID (like I did during our troubleshooting session) with some barely used email account using a weak password. That means, regardless of whether you use it or not for MobileMe/Find My iPhone, you really, really need to give it a SECURE password (if you're going to keep that email account alive). So yeah, there are a lot of dormant Apple IDs floating around out there!

    I agree.
    I found this 'bug' out the other day when getting ready for my new iPhone I was setting up my iPad with some new apps too and wanted to work with Find My iPhone.
    Here's the deal; my main AppleID is just a simple 'Username' not a '[email protected]' AppleID.
    I've had this since the need for AppleIDs were used for these forums and the iTunes Store, AppStore, etc.
    So it works fine and well with that stuff but not with find my iphone on my iPad as it wants a full email account, either a '@me.com' or a '[email protected]' AppleID which I did create but I think it was used as Job profile or something other along those lines (NOT used for a MobileMe account or .mac either).
    And I only have access to one email now and I dont feel comfortable having multiple email addresses that I dont check or have no use for, call my simple or naive but thats just how it goes.
    What I'd like to do is be able to use either AppleID for my Find My iPhone app and everything else.
    And I think thats a good point, '@me.com's for all. make it a whole lot easier in my opinion.
    merge all the apple accounts you created into a MobileMe, simplifies the situation and makes it easier connect to all Apple Services.
    My itunes account, apple.com store account, appstore account, main AppleID for the past couple years it "Maxwell Stanley" but it does NOT work with Find My iPhone. So i created [email protected] (example.com is in place of my true email domain for privacy reasons) and that doesnt work as it statse it Cannot Be used.
    My 'Maxwell Stanley" Apple ID's email associated with it was [email protected] i tried changing it to [email protected] but still doesnt recognize that as an AppleID even though its associated with "Maxwell Stanley".
    I event ried to use the SAME email that is associated with my 2nd AppleID '[email protected]' with the appleid 'Maxwell Stanley' and no dice.
    running out of options it seems.
    Any idea on the best solution?
    Thank you!

  • Office 2013 Technet installation Error 25004. The product key you entered cannot be used on this machine. (System error: - 1073422314)

    I am receiving an error when attempting to install
    Microsoft Office Professional Plus 2013 which I downloaded from the TechNet site.  At the end of the installation process I receive the following message: 
    "Error 25004. The product key you entered cannot be used on this machine. This is most likely due to previous Office 2013 trials being installed. (System error:
    -1073422314)"
    I have never installed a trial or Beta of any Office product on this machine.   However, I have installed Office 2007 Ultimate and Office 2010 Professional Plus.  All of these are 32bit versions downloaded from TechNet site.  In addition,
    prior to this error I had attempted unsuccessfully to install the 64bit version of Office 2013 as well as standalone versions of Visio Professional 2013 x64 and Project professional 2013 x64.   All three of these installations failed due to previous
    installation of 32bit Office software, so I have downloaded the 32 bit versions but not yet tried to install, other than Office 2013. 
    I used the Custom upgrade option during the attempted install of Office 2013, specifying "keep all prior versions".
    Note that all the above was done on a new machine.  The specific purpose was to test co-existence of multiple versions of OFFICE (2007, 2010, 2013) to facilitate user training and migration.
    I have tried uninstalling via Control Panel, and performed some of the steps for manual removal, however did not do all of them since 1) They are quite lengthy and 2) Some of them seem to involve removing ALL prior versions of Office, which I do not want
    to do; the earlier versions are working properly and I do not want to have to uninstall them.  Just want to uninstall and reinstall Office 2013.   Also tried running  O15CTRREMOVE.diagcab which indicated that it could not find a problem,
    but did not seem to remove anything. 
    I have read about ten recommended TechNet articles, which recommend everything from running a FIXIt tool, uninstalling all OFFICE software, and reformatting the whole machine.  Most of these involve System error -1073418209 rather than -1073422314 (which
    is the code that I am getting).   Other than that the problem sounds the same.  This seems to be a problem with key management and copy protection in these products, dating back to 2010.  Dozens of IT professionals have tried the solutions
    and vented their frustration since other than the full format, the other solutions work only sporadically, if at all.  Some of these people had been working with trial or beta software, but many who encountered this problem had not.  As
    noted above, none of my software was a trail version.    I do not want to uninstall all the OFFICE versions, particularly if it as likely as not will not resolve the issue.   (I am also getting paranoid to the extent of fearing that
    after uninstalling everything I might not be able to reinstall any version).  I think what we need here is a definitive fix from Microsoft, though I am not too hopeful, in view of the lack of response to all the other technicians who have been struggling
    with this for at least the past three years. 
    If anyone is aware of a solution which works consistently, I would appreciate it.  Reformatting however is not an option.  Detailed instructions for completely uninstalling Office 2013 (ONLY 2013) might be helpful.  I would be willing to uninstall
    all versions, but only as a last resort, and only if there is some assurance that this will actual solve the problem (for many others it did not seem to do so).
    Thanks
    PS: Probably doesn't matter, but I am running this on Windows 7 Pro w/SP1, 64 bit edition.

    Tony,
    Thanks for your reply.   I do in fact have three versions of Office installed on this machine, 2007 2010 and (hopefully) 2013.  I have on previous occasions installed 2007 and 2010 on a single machine, but this is my first attempt to install
    2013.   
    According to TechNet article  office.microsoft.com/en-us/support/install-and-use-multiple-versions-of-office-on-the-same-pc-HA103981695.aspx (Install
    and use multiple versions of Office on the same PC) it is possible to install
    Office 2003 2007 2010 and 2013 on a single system, provided they are installed in the sequence indicated.  It is noted that some problems may occur, notably involving file associations, but there is no
    mention of any activation key issues.   
    As stated in my original request, the software which I have installed is NOT a trail version.   I did NOT obtain it from the evalcenter, but from
    https://technet.microsoft.com/en-US/subscriptions/securedownloads/hh442904.  
    The above is a full retail version.    The files which I downloaded are:
    en_office_ultimate_2007_united_states_x86_dvd_480625.iso
    en_office_professional_plus_2010_x86_515486.exe
    en_office_professional_plus_2013_x86_dvd_1123673.iso
    I know that the error message says that the problem is commonly caused by attempting to install trial software more than once, but that is not the case.  Several other people have reported this same problem, sometimes involving trial software but not
    in every case.    My own opinion is that this is a software bug involving key management and copy protection. 
    Many people have reported on TechNet that the problem was NOT resolved even after uninstalling all Office software.  While there is a chance I might get lucky, I really would like a solution which has a better chance for success.
    By any chance, does the error code 1073422314
    provide any further insight into this issue?
    Thanks again for your help.  However, further assistance is needed to resolve this issue.
    PS: Sorry the font sizes are so mixed up, I haven't quite figured out how to control the formatting when I paste

  • Can I have multiple text entry boxes on one slide?

    Can I have multiple text entry boxes on one slide, each with it's own possible answer without having to have a separte submit button for each?
    Message was edited by: Suzanne Petty

    I'm using Captivate 5 - I'm thinking I would like to put two or three text entry boxes on one slide - say labeled Name, Email and Company I'd like to have any answer be accepted, yet I still want to have the answers included with the quiz reporting for our main quiz which I set up using a question pool.
    I understand I can uncheck the validate user input box in the general menu in the property inspector, but that also makes the reporting menu inactive for the text entry box.
    Is there a way to make validate user input accept any answer that is typed in the box, but still have the answers reported with my quiz?
    Thanks
    Heather

  • How to save multiple new entries in one shot?

    Hi,
    I am working on a pretty complex Create form. So apart from the standard form fields to allow user to enter the data, one of the sections in this form is a table which allows user to create multiple entries for this entity. And when hitting the "Save" button in this form, it will save all the data plus the multiple entries defined in this table.
    Is it possible to create multiple new entries in a table, and then save all of the new entries at the end? My experience so far is only create and save one new entry at a time.
    Any sample?
    Please advise.
    Thanks.
    -Mina

    Yes, I am using ADF BC.
    Let me explain more in details of the scenario:
    I have a table with "Create New" and "Save" button. The "Create New" button's ActionListener is set to "#{bindings.CreateInsert.execute}", and the "Save" button's ActionListener is set to "#{bindings.Commit.execute}".
    When the "Create New" button is hit, a new row shows up in the table to allow entering data inline. When the "Save" button is hit, it got committed. I would like to allow user to create multiple rows before committing. But currently, after I hit "Create New" button, then enter data, then hit "Create New" button again without committing, it gives error.
    Since this table is part of a form with other fields, I would like to save/commit it until everything in the form are completed, including creating multiple rows in the table.
    Any ideas how to achieve this?
    Any comments are appreciated.
    Thanks.
    -Mina

  • Gl account cannot be used when creating Purchase requisition

    Dear Experts,
    I have the following error message while creating PR :
    G/L account xxxxx cannot be used (please correct)
    Diagnosis
    Comparison of the field selection strings from the G/L account xxxx and the account assignment category W reveals that there is an incompatible combination of field selections for the field selection group 'Business area'.
    I have checked through FS00, the account xxx is a PL statement account and the field status group is Z002.
    How to correct this error?
    Where is mapping between GL account and account assignment category in PR?
    Please advice.
    Thank you.

    Hi Srinivas,
    Thanks for the answer,
    I have mitmatch between OME9 and FSG in OBC4 but still facing error : "Comparison of the field selection strings from the G/L account xxxx and the account assignment category W reveals that there is an incompatible combination of field selections for the field selection group 'Commitment item'.
    The 'commitment item' between OME9 and OBC4 is the same (optional entry).Kindly advice.
    Thanks.

  • Getting error msg while posting entry in GL using F-02

    Hi gurus,
    While i am posting entry in GL using F-02 getting error message as "no controlling area has been assigned to company code"
    can any help me out at the stage i dint want to configure co settings is there any way to pass the entries
    Thanks & regards
    Nandini

    Hi Nandini,
    Have you defined a GL account as a cost element? I think you have multiple company codes which are using same chart of accounts and this company code is also using the same chart of accounts. And also you have configured single controlling area for all company codes. Even though you have not assigned this company code to controlling area. The cost elements will create at controlling area level.
    Due to this system is throwing error message.
    Please check and let us know if you have other issue.
    Regards,
    Mukthar

  • One Way to Fix the "System Extension Cannot Be Used, AppleUSBEthernetHost.kext" Error...

    I found (one) way to fix this error...well, at least it worked for me (see below):
    There seem to be various threads addressing this issue and no "one" way is the right way for everyone. I'm running my Macbook on OS X 10.6.8 (Snow Leopard). Once I installed the iTunes update, two things happened: my iPhone became corrupted when I sync'd via USB and then my iTunes stopped recognizing the iPhone as a "sync-able" device -- meaning it would show up on iTunes but when you went to click sync, the sync button was unavailable.
    I tried locating the .kext file, deleting it, repairing it, replacing with an older version, entered different commands in terminal but I kept getting the same error. Ultimately, I fixed the problem fairly simply, but it may not be something everyone is willing to do. If you have an external hard-drive and had your computer hooked up to Time Machine, this is what you should do:
    Hopefully you'd been backing your computer up automatically fairly recently, and you have some this stored on an external hard drive via Time Machine from before iTunes 11.4 was downloaded onto your computer.
    If you haven't done so already, and your iTunes library isn't corrupt, Backup your entire iTunes library to an external hard-drive (if you don't care about your library, ignore this step...this procedure might not work, however, if your first backup of your iTunes library is via version 11.4. If you go through all of these steps and you encounter the same problem, restore your itunes to an older version via Time Machine, then redo steps)
    To do this, create a new Folder on your hard drive and call it "iTunes"
    Go into your iTunes preferences > Advanced > under "iTunes Media folder location" we want it to say /Volumes/(Your Hard Drive Name)/iTunesNext to the "iTunes Media folder location" dialogue box, it should read CHANGE or RESET. Click CHANGE, navigate to your external hard drive and locate the newly created iTunes folder...your computer should automatically start to transfer your library to the new destination.       
    Backup and "new files" on your computer that you create since updating your iTunes to version 11.4 (i.e. new iCal entries, documents)
    Backup your important files (I have mine in dropbox but chose to be safe and backed them up on an external hard drive as well)
    Once you have everything saved, you're going to want to go through the process of completely restoring your entire computer (essentially wiping it clean).
    To do this on Snow Leopard, you need to have the Mac OS X Snow Leopard Installing disc.
    Insert disc > when the Install screen pops up, select Utilities... > it will then prompt you to Restart your computer
    After your computer restarts, it will prompt you to reinstall Snow Leopard or select a different option from Utilities which can now be found at the top of your screen on the toolbar. From there, select the option that is along the lines of Restore from Backup Using Time Machine and then select which backup you want to restore your computer to ... since iTunes 11.4 went live on Sept. 10th, I would restore to any date before that.
    When your computer restores itself to your chosen backup, your computer should be exactly as it was on that date, iTunes included. It's as if nothing ever happened.
    To do this on any later OS X, I believe you have to restart your computer and then hold COMMAND+R before the grey screen appears. From here, I believe it will prompt you similarly to the Snow Leopard procedures 1-3 as listed just above this bullet point.
    When your computer prompts you to update iTunes to version 11.4 from whatever version you reverted back to, DO NOT UPDATE. Keep your old iTunes version and wait for this thing to be addressed by Apple.
    This procedure worked for me and although it's a bit tedious, it fixed both my iTunes and iPhone errors. Note: I did have to erase and restore my iPhone through an old backup via iTunes once iTunes was working again. Try it out. See if it works for you. MAKE SURE YOU BACKUP YOUR FILES BEFORE ATTEMPTING ANY FULL SYSTEM RESTORE.

    There's more to it than this IMHO.  Here is my explanation:
    If I go back in my Time Machine backups and restore the previous version before I installed iTunes 11.4, the version of that same kext was also listed as being "7.0" despite being older and twice the size (120400 bytes vs. 63024 bytes in the 11.4-installed version).
    (The older version is "BuildVersion 305" and "SourceVersion 122000000000000"; the new 11.4 version is "BuildVersion 417" and "SourceVersion 113000000000000".)
    The real problem is this:
    /System/Library/Extensions/AppleUSBEthernetHost.kext/Contents/_CodeSignature used to contain
    -rw-r--r--+ 1 root  wheel  172 Jan 31  2014 CodeDirectory
    -rw-r--r--+ 1 root  wheel    92 Jan 31  2014 CodeRequirements
    -rw-r--r--+ 1 root  wheel  1745 Jan 31  2014 CodeResources
    -rw-r--r--+ 1 root  wheel  4064 Jan 31  2014 CodeSignature
    /System/Library/Extensions/AppleUSBEthernetHost.kext/Contents used to contain symbolic links down into there:
    lrwxr-xr-x+ 1 root  wheel    28 Jun 12  2012 CodeDirectory@ -> _CodeSignature/CodeDirectory
    lrwxr-xr-x+ 1 root  wheel    31 Jun 12  2012 CodeRequirements@ -> _CodeSignature/CodeRequirements
    lrwxr-xr-x+ 1 root  wheel    28 Jun 12  2012 CodeSignature@ -> _CodeSignature/CodeSignature
    When iTunes 11.4 was installed via Software Update/App Store, it removed CodeDirectory/CodeRequirements/CodeSignature but it did not remove the corresponding symbolic links.  Presumably that is what triggered the "cannot be used" pop-up message.
    Trashing the kext and installing it from the downloaded 11.4 .dmg does not create the symbolic links, thus avoiding the problem.
    Obviously rolling back to the previous (Jan 2014) kext will fix the problem as well as the symbolic links point to files that exist.
    (I'm really curious to know what happened between BuildVersion 305 and BuildVersion 417 that caused it to shrink nearly by half.  It looks to me like the Code Signing stuff got ripped out - Lord knows why.)

Maybe you are looking for