Qosmio X-300 serious monitor issue

Hello there,
Just to start with - I am using all defaul Toshiba drivers, everything original from Toshiba.
Got a serious issue here with monitor - at some point after playing for about 30-40 minutes the monitor goes blank and then changes colours randomly, from brown to green. This conitunes on for about 3 minutes then goes back to normal. In about 15 minutes it repeats again and so on. As you can guess it makes gaming on the laptop practically impossible.
Any ideas what to do with that?
Thanks beforehand

Hi,
I think, it's a card graphic issue, playing games makes it running hard. I recommend you select ,,High performance,, in power plan. Also, have you tried to clean the laptop with the compressed air spray?

Similar Messages

Qosmio G30-137 - Video card issue - the vertical lines bug

Hi members,
today my Qosmio G30-137 started making troubles showing vertical lines which look like this:
After using product recovery disk Windows was unable to initiate first start and came up with a bluescreen with the error-code:
+page fault in non-paged area STOP 0x00000050 (0xC09C3044, 0x00000000, 0X804DA90AA, 0X000000002)+
This basically indicates that memory - either RAM, L2-Cache or Videomemory died. But i also learned that the graphic card can be smoked.
After the blue screen you wont get the system into normal working condition, no matter what you try.
I would strongly advise to check if your Qosmio is under warranty and see your dealer for exchange. Fortunately i bought mine 2006/06/06 so its still under warranty (even if just a view days left).
Additional information: another member of this forum had a similar problem and reported that the whole motherboard has to be changed which causes cost of USD 700.00 and up!
I will let you know what i ended up with.
BRgds
The Q

Unfortunately, this sounds like a serious hardware issue as the other member suggested, the GPU (graphic card) could be faulty and therefore the replacement is necessary.
The point is that the GPU is soldered on the motherboard and its not possible to remove the graphic chip from the board. In most cases the whole motherboard must be replaced to solve such graphic problems.
In my opinion you should contact your ASP as fast as possible.
The technicians should be able to help you explain the whole situation and you issue and ask for the further handling.
Good luck buddy

Serious UI issues in SQL Developer 4.0 for Mac

I've encountered some serious UI issues in SQL Developer 4.0 for Mac (4.0.0.13) that impact it up to the point where it becomes unusable.
If the database and tables are expanded in the "Connections" view, sometimes a node in the tree seems to become sticky. Whenever you scroll the up or down, it will immediately scroll back to make the old selection visible again. If you want to work with an item that's outside the current view (e.g. to collapse the "Tables" node), you can no longer use it. SQL Developer needs to be restarted.
If the context menu is opened (ctrl click), it appears in the wrong place. It's too far to the right and bottom. If you then move the mouse pointer towards the menu, a rectangle appears and follows the mouse pointer as if you had initiated a drag and drop operation.
If the "Data" tab of a table is selected and if a cell is clicked to edit the cell value, the text cursor is drawn in the wrong position. It can be off by more than one character and it is often drawn in the middle of a character instead of between two characters. It's hardly possible to edit the cell value as you cannot tell for sure where insertions and deletions will happen. You basically need to copy the value into a separate editor, edit it there and copy it back.
The scrolling in the "Data" tab of a table is a pain. For no obvious reason, it first scrolls downwards a few rows and then jumps to the top (at least using a Magic Mouse). If all rows have been loaded, this problem seems to disappear. But generally, the scrolling distance is far too short. With a long finger swipe, one would expect to scroll the contents by several pages. However, it only scrolls about half a page. For shorter swipes, it's similar. It sometimes only scrolls by a few pixels.
Am I the only one to experience these severe problems? Or is the Mac version not as mature as the Windows version yet?

In terms of diagnosis, perhaps not -- probably very time-consuming to debug. I did find some unpublished bugs against dual monitor use ...
Bug 13727841 - FORUM: 64BIT WIN7 SOME DIALOGS SHOW ON DISPLAY 1 WHEN SQLDEV ON DISPLAY 2
Bug 18504928 - NEW CONSTRAINT UI MENU IN TABLE DIALOG AT WRONG LOCATION ON DUAL MONITOR
The first turned out to be an issue in the 64-bit Java AWT libraries, not the 32-bit libraries, and specifically for Windows 7 as opposed to, say XP, but this was all quite a bit in the past and was fixed for 4.0. The second one (on 64-bit Linux), however, just came in yesterday, so you can wait to see if a fix for that also covers your situation or, if you are able, pursue it directly with Oracle Support.

SERIOUS lag issues with Intel iMac

Hello everyone,
I'm pretty frustrated right now. I've been having this serious lag issue with my new iMac for the past few days. I think it may have started after I ran the last security update.
What happens:
When switching between apps, the system will hang for 1-3 seconds between doing anything. This includes typing, mouse requests, etc. It's VERY frustrating. I have activity monitor open currently, and I am seeing both Safari and SystemUIServer hogging up the CPU resources like CRAZY. I've even seen Safari recently give a CPU usage of 120%, right before I loaded this webpage. tis isn't just centralized to Safari too.... I have the following apps running:
Adium 0.89.1
FoireFox 1.5.0.8
Safari
Activity Monitor
My Memory stats currently are:
175MB Wired
708MB Active
618MB Inactive
1.47GB Used
There should be no reason I'm getting these lags with just two web browsers and a chat client open.
Has anyone else expierenced the lags?? Any suggestions? I'm almost ready to reinstall OS X and not run the last security update. Thanks
iMac 1.83 GHz Core Duo Mac OS X (10.4.8) 1.5GB RAM, Extermal LaCie 160GB FW Porsche Drive, Griffin iMate, iPod Min 4GB, JBL Creature Speakers

Hello Matthew
Are you running any maintenance scripts on a regular basis?
http://www.thexlab.com/faqs/maintscripts.html
I would manually run this script from The X Lab, and my load times would improve greatly. The problem was, I would forget to run them untill I noticed web pages loading slow or iTunes and iPhoto taking for ever. It wasn't untill someone here in discussions suggested Anacron that I saw the light. WOW what a difference Anacron has been making in my overall system speed. My iMac has not been shutdown for 11days 5hrs 34mins (sleep or use only) and opening new App's, switching App's and web pages load as fast or faster than after a fresh start up. If your system is operating properly and you are having only what seems to be a slow or sluggish issue Anacron will make a difference.
http://members.cox.net/18james/anacron-tiger.html
Dennis
17" iMac Intel Core Duo 1.5GB Ram Mac OS X (10.4.8) Maxtor 300GB FireWire 2G Nano

Analysis could not be performed in time. There is a possible serious performance issue

Can someone please advise what I need to do to correct this critical error?
My computer is VERY slow and when I ran the event viewer, this is listed as CRITICAL. Any information would be appreciated.
Log Name:      Microsoft-Windows-Diagnostics-Performance/Operational
Source:        Microsoft-Windows-Diagnostics-Performance
Date:          6/24/2010 10:18:46 AM
Event ID:      400
Task Category: System Performance Monitoring
Level:         Critical
Keywords:      Event Log
User:          LOCAL SERVICE
Computer:      user-PC
Description:
Information about the system performance monitoring event:
     Scenario  : System Responsiveness
     Analysis result  : Analysis could not be performed in time. There is a possible serious performance issue
     Incident Time (UTC) : 6/24/2010 5:17:07 PM
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Microsoft-Windows-Diagnostics-Performance" Guid="{cfc18ec0-96b1-4eba-961b-622caee05b0a}" />
    <EventID>400</EventID>
    <Version>1</Version>
    <Level>1</Level>
    <Task>4005</Task>
    <Opcode>37</Opcode>
    <Keywords>0x8000000000010000</Keywords>
    <TimeCreated SystemTime="2010-06-24T17:18:46.941Z" />
    <EventRecordID>5491</EventRecordID>
    <Correlation ActivityID="{00000000-E6C8-0000-F4BB-058D9113CB01}" />
    <Execution ProcessID="1884" ThreadID="5956" />
    <Channel>Microsoft-Windows-Diagnostics-Performance/Operational</Channel>
    <Computer>user-PC</Computer>
    <Security UserID="S-1-5-19" />
</System>
<EventData>
    <Data Name="ShellScenarioStartTime">2010-06-24T17:17:07.442Z</Data>
    <Data Name="ShellScenarioEndTime">2010-06-24T17:17:12.442Z</Data>
    <Data Name="ShellSubScenario">1</Data>
    <Data Name="ShellScenarioDuration">5000</Data>
    <Data Name="ShellRootCauseBits">0</Data>
    <Data Name="ShellAnalysisResult">2</Data>
    <Data Name="ShellDegradationType">1</Data>
    <Data Name="ShellTsVersion">1</Data>
    <Data Name="ShellMachineUpTimeHours">0</Data>
    <Data Name="ShellMachineSleepPattern">0</Data>
</EventData>
</Event>

I do get the same problem. It believe it started after I switched from HDD to SSD some month's ago. My machine is very fast now so I do not have performance problems (only a very slow power on boot).
The description above is exactly the same as I have.
Does somebody has the same problems?

Serious resolution issues with After Effects CC (2014) on Windows 8.1 Pro on Dell Precision M3800 laptop??

My new company installed Adobe Creative Cloud (There was some annoying Proxy issues at first, because of the seriously tight I.T policies) but we are having some serious resolution issues with After Effects CC 2014 (also have this resolution problem with Adobe Premiere, Media Encoder, Muse) on Windows 8.1 Pro on a Dell Precision M3800 laptop with icons and interface looking too small and hard to see, is there a fix, an update or a work around, can anyone help?
Any help will be appreciated!
k.regards
Ramon

Hi Todd is there a time-frame for this fix, there is a lot of pressure on me, because I convinced my company to get the Creative Cloud and quite a lot of the CC software is not compatible with the latest Windows 8.1 OS.
Is there at least a work around, until this big fix comes along?
k.regards
Ramon

Trouble with color on Presario, No red tones on display. Not a monitor issue.

Am experiencing trouble with color on Presario, model no. CQ5500F. Purchased a couple of years ago, and trouble was present immediately. Am getting no red tones - red items appear black or sometimes blue. Was told by HP that it was a monitor issue, and let computer slide out of warranty. installed new monitor today and problem still exists. Is this merely a display adjustment of some kind? Or will I have to pay HP their $99 for a one time fix? Any suggestions appreciated.

Hello UncleBob62,
It could be the display driver that is not properly working
1. Click on the start icon
2. Right click on computer and go to properties
3. Select Device Manager
4. Expand display adapters and right click on the video card driver and uninstall
The computer screen will go blank
On the keyboard press the windows key the right arrow key twice and then the letter R.
At this point your computer is going to reboot. After the reboot Windows will install generic drivers for your video card. Do you still see a lack of red tones?
If I have helped you in any way click the Kudos button to say Thanks.
The community works together, click Accept as Solution on the post that solves your issue for other members of the community to benefit from the solution.
- Friendship is magical.

Qosmio G40-108: starange display issue with highest resolution

I just got mine but on its highest resolution all webpages have these 11 semi-rectangular blocks, barely visible, only the bottoms, each about an inch long, is this normal and should i send it back to be investigated?

Hello
It is very nice to hear that you already have newest Qosmio notebook. About your issue I can not say much because without one screenshot it is not easy to understand what you mean exactly. On my Qosmio G30 (with the same HD resolution) I have no problems at all. Because of that I can really not understand what is wrong there.
If possible post a link where we can see how it looks like. Your description is not enough.
BTW: have you noticed this on web pages only?

Seriously, this issue is really annoying. why wont my songs download? it wont stop saying there is an error. this needs to be fixed. refund or apple needs to put these songs in my itunes manually if that can be done.

seriously, this issue is really annoying. why wont my songs download? it wont stop saying there is an error. this needs to be fixed. refund or apple needs to put these songs in my itunes manually if that can be done.

seriously, this issue is really annoying. why wont my songs download? it wont stop saying there is an error. this needs to be fixed. refund or apple needs to put these songs in my itunes manually if that can be done.

Multiple Monitor Issue

Alright, so I have a 15" Macbook Pro with the dual graphics cards (GeForce 9600M GT and GeForce 9400M GT 256 version). It's the 2.66 intel processor one. Anyway, I've been trying to figure out this dual monitor issue that I've been having for a few days now. When I'm using the 9400M card and I plug into my mini displayport everything works just fine. This includes the VGA cord, the HDMI, as well as a standard Apple monitor. Now, when I switch over to the higher end graphics card, as soon as I plug into the mini displayport my screen goes black. And that's it. I can't do anything. I have to hold the power button down until the computer turns off.
I've been searching for days in order to find an answer to this question or if anyone has ever had a similar problem and no one could help me. I even went to the genius bar and no one could help either. Keep in mind I've tried this in a variety of ways. I've plugged the monitor in after the computer was running, I've had it plugged in while the computer was turning on, and each time after the initial boot up everything goes black.
To make matters worse, I originally came across this issue because I use Windows 7 on bootcamp and I wanted to use dual monitors within Windows. Bootcamp is only set to use the 9600M graphics card which is the one giving me all the heartache and apparently there's no way around it. If anyone has the slightest clue as to what's going on here or why it would be doing such a thing, let me know. Thanks.

Jon: Thanks for answering those questions. Run the Apple Hardware Test that you'll find on one of the DVDs that came with your MBP. If any errors are reported, go back to the Genius Bar with the error codes reported by AHT and ask to have the machine repaired.
If you have extended AppleCare protection, you have a TechTool Deluxe CD/DVD. You can also use that to test your hardware. If it reports any errors, take the exact wording and error codes from that report along with you to the GB, too.
The problem is not with your three external displays or your cables, adapters, or your MBP's mini-Displayport, because they all work fine with the 9400M. The problem isn't some wrong contact that's being made momentarily as you insert the mini-Displayport plug into the port, because it occurs even when the cable is securely connected before starting up the computer. It seems to me the problem must reside either in your 9600M GT or in its connection to the mini-displayport.

Graphics card issue or monitor issue?

Hello, i have a MacPro 2.66 w/ an ATI x1900 and a MacBookPro with th nVidia 8600
i recently purchased a 28" Hanns-g Display which i upgraded from my 20" apple cinema display, im curious if this could be a graphic issue or a monitor issue:
When i connect the 28" monitor to my ATI card (port 1) and boot into 10.4.10 (macPro) i noticed diagonal lines that seem to "scroll" (like an overscan line or something) on greyish and lighter backgrounds.
tried it with the second port, same thing, it does it on all resolutions
(it runs @ 1920x1200).
when i boot into XP and try the same sites i did in 10.4.10 it doesnt do it at all, its as it should.
I tried both VGA>DVI and HDMI>DVI to the ATI on OSX but it only does it with the HDMI>DVI connection under OSX, VGA looks fine.
(btw my ati card is clean as a whistle, no dust or anything)
However if i plug it into my MacBookPRo with hdmi>DVI it doesnt do that at all.
so im wondering probably incompatible monitor or what?
im looking to getting a 30" Apple Display but not if its gonna act up like that on my macpro, none of this appeared on my ACD 20".
any suggestions or tips?
thanks!

im not experiencing scan line son my 30" ACD display under OSX or XP with my ATI, could be the monitor you are using, but if its not doing it with your MBP than.....idk
sonds strange, try another gfx card or another macpro if possible.

Playing off the Timeline via firewire( XdCam pal) Monitoring Issues

Hey,
I have just switched to FCP and have found that when recording the from the FCP timeline manually via firewire into a Sony XDCam PDW530 I experience 4:3 flashes in the Camera monitor and viewfinder as the timeline plays down Video Transitions. All effects have been rendered (Blue line above transition)
However the Camera appears to record correctly to disc. I played the recorded material from the camera via an XD deck into a wide screen monitor and all appears fine the 4:3 flashes are not present on transitions. play the disc back in the camera and the 4:3 flashes for the duration of the Video Transitions return????
when playing out of the Camera via SDI and Analogue Composite outputs into a wide screen monitor all appears ok as well.
It's a little odd that you cannot monitor the output correctly on the XDcam. If i change the pull down settings from 2323 to 2332 it monitors the transitions correctly but the video aspect is somewhere between 4:3 and 16:9.
Shoot in 16:9 Capture DV Pal, Edit DV Pal, Playback Output Apple FireWire Pal (720 x 576)
Any ideas????

Thanks Shane,
We have been down the PRINT TO VIDEO road with the same playback issues in the XD Camera's LCD screen. We still see the 4:3 transition on the 16:9 image when playing off the timeline / playing back the recorded media in the camera and viewing on cameras screen .
I guess this is only a monitor issue. If you don't include any video effects it plays down 16:9 perfectly in the cameras monitor
What is recorded onto the disc is fine.
Also my understanding is the what's coming off the timeline is a DV stream so not sure how the GOP format comes into play. Recording onto a XD Cam off the timeline thru other edit programmes has never been an issue. I have come from Avid Pinnacle and the monitoring of transitions was never an issue when streaming back to the xdcam.
Thanks

For All Serious Burning Issues!!

If you are having serious burning issues and error messages, and after you have freed up atleast 5 gb of HD space on your STARTUP drive (Startup is the drive that your OS is running on) then go to:
http://superdrive.cynikal.net/
and download the appropriate Superdrive firmware for your computer. i have used this site several times. Make sure you follow the directions. This is a major change to the software that runs inside of your superdrive, but it usually does the trick for me when I have issues. If you have previously updated your firmware, and are now having issues, go back to the original firmware and see if that works, (it usually does for me). I have updated several times, and never had any issues. My superdrive is atleast 2 and a half years old with heavy use.
Not sure if Apple approves of doing this, but they don't seem to ever be very helpful with error messages, so this is the best solution for me.

Not really. You only need enough space to cover the amount of data being burned to the disc, which in most cases is 4.7 gb. You will need more if you are burning larger dvd's and/or dual layer. For years, I have only kept roughly 5 gb available on my system and haven't had any problems.

Serious Performance issue in ADF?

Hi Everyone,
My Jdev version is 11.1.2.3.0.
I have developed one ADF application and deployed into web logic server.
I am accessing this page through url in one portal of client.
After clicking on the page link in portal it opens the page and the page has search page(test field, submitbutton and result table).
On clicking on submit button sometimes the result in the table comes in few seconds and sometimes it takes few minutes.
its a very serious performance issue.
What should i do to increase performance for my ADF page?
why it takes much time sometimes?
Please give suggestions.
Thanks.

Hi Kumar,
Try to ensure proper indexes are placed based on search criteria in base table which will definitely increase the performance. Be sure to check the explain plan to see the performance of query instead of just running it in toad. If you feel everything is good from back end, you can tune your view object, go to view object editor->tuning and set the page range size=25 or some smaller value and see if that increases the performance.
Refer below link for more guidelines:
http://docs.oracle.com/cd/E17904_01/core.1111/e10108/adf.htm
Regards,
Ravi Nuka

Serious Volume Issues : HELP!

Good Morning,
We have had Fios for about 8 month and since we signed up have been having serious volume issues. When we turn on the tv and the fios (HD Box w/DVR) the volume will turn on and it will be in a mono tone with no bass just very bad sounding, other times we turn it on and there is no sound. To get "normal sound" we typically have to turn on and off tv a couple times to get to work. If we turn on tv and have "funny sound" we can flip to DVR and watch tv with perfectly fine sound. We can also turn on DVD player and watch tv with perfectly fine sound. This makes me think it's fios or the box?? We have had a refresh to our box and we just recieved a new box and it is still happpening!! My husband has switched the HDMI cables to the alternate port on our tv (I think that is what he said??) and nothing helps. Our tv is a Samsung LCD and it is maybe 2 1/2 years old at the most. We have never had any issues with this with Directv and can't figure it out. Does anyone have any advice?
Our second issue is on our other tv when we turn on the fios box and attempt to watch tv, Spanish music comes through the subwoofer of our sound sound. Again never an issue until Fios. My husband bought a RF (????) filter and no such luck. Any suggestions?
Thanks as we can not watch tv in our home without it being a huge pain in the butt!

seeing as how the issue is the same with 2 different HD-DVR's I would assume it is one of the many HDMI issues that occur with the motorolla boxes... try another means of cabling for audio... such as composite (red/white) or digital audio cable
as far as the other box is concerned, with the spanish audio..... that box/TV probably has the SAP turned on.... on the box, go to Menu > Settings > Language > Audio Language.... and switch to English preffered... if it is your TV, consult the owners manual for specific instructions on how to change the setting on the TV.
Bob Robertson - Lighter Klepto - I steal lighters, not bandwith

Qosmio X-300 serious monitor issue

Similar Messages

Maybe you are looking for