Queue error in BPM

Hi,
We are working in PI7.0. We have implemented an integration scenario where we use iDocs and BPMs.
When we start the workflow, we get the following error in queues: "Copy Sender from Payload: Sender is Missing in Pay", and the queue gets blocked.
In another similar scenario, we use the same iDoc header directed to the same destination, and the queues do not get blocked.
Which is the problem?
Thanks in advance,
Samantha.

Hi,
Copy Sender from Payload: Sender is Missing in Pay
1. Cross check the mapping again, have you assigned all the required fields for header mapping
2. If you are not doing header mapping in payload then Cross check in Integration directory that the checkbox " Apply control from payload" in receiver comm. channel for IDOC is unchecked.
Regards,
Sachin

Similar Messages

Permenant error in bpm inbound processing error in inbound queue of pi7.1

Hi Experts,
In E filling scenario in SAPPI7.1, iam facing a problem. i.e In sxmb_moni message monitoring, the message was schedule at outbound side.when i extend that, the message was stuck in smq2 with "permenant error in bpm inbound processing".can any one please tell me how to relove this issue.
Thanks & Regards,
Giri.

Hello
Check the note #1126656 BPE-TS: Permanent errors in the BPE inbound processing. This describes some possible causes and solutions for this error.
Regards
Mark

How to catch SAP application errors in BPM.

Hi,
I have a IDOC to Soap Sync Scenario where I send the message to a Webservice. I have used a BPM since we need to catch the resposne of this message and map it to a RFC. For ex if I get a success resposne I need to map success if not than I need to catch the error and map it to the RFC. Now here in some cases like if the target system (webservice) is down than XI raises a sap application error:
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>XIAdapterFramework</SAP:Category>
<SAP:Code area="MESSAGE">GENERAL</SAP:Code>
<SAP:P1 />
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText>com.sap.aii.af.ra.ms.api.DeliveryException: Connection refused (errno:239)</SAP:AdditionalText>
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack />
<SAP:Retry>M</SAP:Retry>
</SAP:Error>
Normally XI stops the process in these cases and does not proceed to the next step but I need to catch this message and map the content in the AdditionalText to the target RFC. Can anyone let me know how to catch this SAP Application Error in BPM and map it to the RFC.
Thanks,
Bhargav

Hi Gaurav,
As I have mentioned I need to catch the application error in the BPM. If you see the discussion that is mentioned after the blog you have mentioned it is stated that the fault messages or the application error cannot be caught in BPM.
In the blog that you stated we can catch the fault message and map it to a message structure but only to that extent after that it would stop the BPM process at that step but would not proceed further as shown in the screenshot given in the blog it would fail as "application error restart not possible".
I need to proceed further and capture this error to an RFC Structure and call a proxy.
Here after the error it does not proceed to the next step.
Thanks,
Bhargav

Inbound queue error

Hi Gurus,
I am facing a problem with inbound RFC Queue,error message is logical system not defined in table smof_erpsh.
i hav e cheked the table but not too sure about how to activate the queue.
please help.
Regards,
Samarjit

Sounds like you switched backends on the CRM system. You can only have one ERP backend connected to a CRM system, in a normal typical landscape without special customizing.
You may also had a system that was copied from the original backend that is now trying to send bdocs to your crm system. Can you tell us a little more about your system landscape and we can then see what needs to be done?

Sync/Async brdige error in BPM

Hi,
I am working on RFC-TO-Webservice scenario(Synchronous) and I am using the BPM in this scenario.
In BPM just I have used 2 steps.
Receive - Opened Sync/Async bridge
Send - Synchrouns step
Send - Cloase the Receive step
Send - Asynchrous send step (to send the response to the file...).
When I sent my RFC message from R/3 I am getting following error.
<?xml version="1.0" encoding="UTF-8" standalone="yes" ?>
- 
- <SAP:Error xmlns:SAP="http://sap.com/xi/XI/Message/30" xmlns:SOAP="http://schemas.xmlsoap.org/soap/envelope/" SOAP:mustUnderstand="1">
<SAP:Category>XIServer</SAP:Category>
<SAP:Code area="INTERNAL">PL_TIMEOUT</SAP:Code>
<SAP:P1 />
<SAP:P2 />
<SAP:P3 />
<SAP:P4 />
<SAP:AdditionalText />
<SAP:ApplicationFaultMessage namespace="" />
<SAP:Stack>Timeout condition of pipeline reached</SAP:Stack>
<SAP:Retry>N</SAP:Retry>
</SAP:Error>
I am using PI 7.0 SP13 is why I am not able to receive the Sync message in BPM...I have created the abstract interface based on RFC...getting the first message itself Timeout error.
I am trying to use Sync/Asnc bridge in BPM. First message itself PL_TIMEOUT error..bpm is not able to receive my rfc request...
I need help on this...do I need to do any settings in WEBAS level..I did Timeout setting in SXMB_ADM.
Regards,
Venu.

hi,
https://www.sdn.sap.com/irj/sdn/weblogs?blog=/pub/wlg/1403 [original link is broken] [original link is broken] [original link is broken]
check this blog..and same thing I did in my scenario
my scenario is RFC-TO-Webservice.
Sync/Async bridge can't we use like this ...Receiver step(open sync/async)-> Send(Synchronous)-Send(Close sync bridge)....that way can't we use ...
I am not able to receive the RFC request itself inside my BPM first step...getting the Timeout error.
But when I use the RECEIVE STEP with Asynchronous mode..I am able to receive the message inside my bpm.Incase of Synchronous I am not able to receive the message..
I am working PI 7.0 and SP13..did any body worked this version...
Thanks,
venu.

Mapping Errors in BPM

Hi All,
How can the mapping errors in BPM be handeld implicitly (without the use of Exception Handling Branch)
Regards,
Anurag

Hi Anurag.
Handling the mapping exceptions in BPM could be possible using the Alerts.
Go through this blog for Alert Configuration:
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
And also go through this thread:
alert in BPM
Hope this helps you.
Regards,
Hari.

Block1 (No agent) Error in BPM ?

Hi friends ,
 I am trying the the BPM scenario using Integration Process
BpmPatternCollectTime
from SAP BASIS ® SAP BASIS 7.00 in the namespace http://sap.com/xi/XI/System/Patterns
I have done the scenario like the above . I have followed all the Steps which are used in above scenario.
I am using a File Sender Adapter and Receiver Adapter .
It is Successfully picked up the File but nothing is happening after that .
I am using two receiver Determination one from Ob to IP and other from IP to FIleReceiver ( IB) .
But, I am Getting error as Block1 (No agent) Error in the PE graphical diagram
I have checked in SWWL my Integration Process Return code is "0"
Can you please tell tell me how to solve this ?
Can you please tell me this scenario is like Multiple Purchase Order Items to One Purchase Order
Here they have given ID adn OverAllNumber . For ex. In one xml file I am sending
ID as A100
OverAllNumber as 120
next 5 minutes putting the another file with contents
ID as A100
OverAllNumber as 130
My Question is
Will TWO files wiil come as Output in File Receiver ?
 I am Clear in this please give some suggestions
Best Regards.,
V.Rangarajan
Best Regards.,
V.Rangarajan

Hi,
 Thanks for your reply.
 once the files are connected in the transformation step you will use a N:1 mappping.
 Yes , i have done as same . I have set deadline as 15 minutes .
My doubt is
 if N:1 
First File
ID as A100
OverAllNumber as 120
next 5 minutes putting the another file with contents
SecondFile
ID as A100
OverAllNumber as 130
 Then what will be the output ?
 will it be like this
 ID as A100
 OverAllNumber as 130
 I am not clear in this Please tell me !
 If possible please give some suggestion to clear this Block1 (No agent) Error in BPM ?
Regards.,
V.Rangarajan

Error in BPM: FIle to RFC

Hi friends,
   I am working on File --> RFC ---> File Scenario using BPM ...
Here I am getting system error in BPM and showing broken red brick in workflow at sender1 ...
I have given like this...
Start --> Receiver ->sender1>Sender2 ---> Stop.
I have given properties... for each
C2 = Abstractinterface FIleResponse_Abs
Recevier
1)Step Name = Receiver
Message   = C1 (I defiend in container Category =Abstact interface type = FileRequest_Abs)
Start process = (Selected)
Mode = Asynchronous
2)Sender1
Step name = Sender1
Mode =Synchronous
Synchronous Interface = FileRequest_AI
Request Message= C1
Response Message=C2
3)Sender2
Step Name =Send2
Mode = Asynchronous
Message = C2
After Configartion,I have placed the sender sample XML in Server ...it is picking up properly.But
it showing error while it was executing in the BPM. Please suggest me what i have to do.
If you didnt understand I ll give some more details.
Pls help me in this regard.
With Regards,
Raju.

I am getting error in Integration Engine.....
Attribute     Value
Engine     Integration Engine
Status     System Error
Repeatable     No
Cancelable     No
Start     20.06.2007 06:25:22
End     20.06.2007 06:25:22
Sender Party
Sender Service     BPM_FILE_RFC_SAGAR
Sender Interface     http://File2RFC_Syn
FileRequest_AI
Receiver Party
Receiver Service     ECCIDOC800
Receiver Interface     urn:sap-com:document:sap:rfc:functions
BAPI_SALESORDER_GETLIST
Quality of Service     Best Effort
Error Category
Error Code
Message     9BA7365DDBC0FE49B9F512F7308DDA53
Reference

Inbound queue error"XI Error APPLICATION_ERROR.ABAP: Queue stopped"

Hi,
In SMQ2 ,we have received inbound queue error "XI Error APPLICATION_ERROR.ABAP: Queue stopped".When activate queue error is not going.So please advice.
Thanks,
Praveen

Hello Mr,
Have a look into SAP Notes: 824554, 906435, 783515, 910649, 706563.
/people/sap.user72/blog/2005/11/29/xi-how-to-re-process-failed-xi-messages-automatically
To be more helpful, can you post here complete error log?

Queue Prioritization with BPM

I am trying to get messages coming into a BPM to use a high priority EOIO queue, without success. I am not really sure I understand why BPM's always use EOIO queues, but I am accepting that and just trying to get a few into a higher priority queue.
The message coming from the adapter always seem to go to an XBQO$PE_WSxxxxxxx queue specific to the adapter. I've made an attempt to set up queue prioritization in SXMSQUEUE, but am really not sure abou the 'message queue' parameter in the in the filter setup.
What value do I need to use here ? Anything I desire to use ? Does it need to match up with a corresponding parameter anywhere else ? No matter what I try they just end up going to XBQO$PE... queue. I do have filters set to influence other steps to go to a high priority EO queue, but can't seem to get a BPM to do so in an EOIO.
Thanks for any help,
Tim

Hi Tim,
Always the queue for a BPM process will be generated with the name XBQ0_WS* where WS* will be the workflow id which you can see thru PFTC_DIS transaction of your ABAP stack...Thats the default design of SAP and all the messages will go in a EOIO manner into this queue and gets assigned into the Process Engine.
There is nothing much we can do explicitly on this queue assignment as we also faced the same issue in case of interfaces with BPM where idocs will be flowing into XI in bulk...
Cheers
JK

Alert Monitoring - ID failures and Queue errors

Hi,
In our project we need to trigger alerts for cases apart from Mapping Errors, Application Errors and Adapter Erors like the cases mentioned below :
1. A Message gets stuck in the QUEUE of ECC system
2. The ID has errors like the Receiver Determination has errors.
How can we trigger the Alerts and see them in Our Alert Inbox .
Regards,
Arunava

Hi ,
For runtime errors , you can trigger an alert.
I don't think so, it is possible to trigger an alert when message is stuck in Queue, but if you get any error either system error or application error then you can trigger an alert.
For more-
http://help.sap.com/saphelp_nw2004s/helpdata/en/80/942f3ffed33d67e10000000a114084/frameset.htm
/people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step
If you have got any errors like communication errors because of Queue error, then you can think of configuring CCMS alerts.(i.e alerts for Components)
/people/aravindh.prasanna/blog/2005/12/23/configuring-scenario-specific-e-mail-alerts-in-xi-ccms-part--1
Regards,
moorthy

HT3669 My macbook pro does not print through my PC to my EPSON RX 500 after loading OS X 10.7.4. It shows on the print queue "error" However, it will print if I directly connect my laptop to this printer via the USB connection. Any ideas?

My macbook pro does not print through my PC to my EPSON RX 500 after loading OS X 10.7.4. It shows on the print queue "error" However, it will print if I directly connect my laptop to this printer via the USB connection. Any ideas?

It's all about setting up what ever version of windows you have running on your pc to share the printer. If you still get stuck post in a windows forum for help.

Queue generated by BPM?

Hi all,
Every BPM creates a seperate queue XBQO$PE_WS90100010. But is this queue a EOIO queue or a simple EO queue?
Regards

Hi Tim,
Always the queue for a BPM process will be generated with the name XBQ0_WS* where WS* will be the workflow id which you can see thru PFTC_DIS transaction of your ABAP stack...Thats the default design of SAP and all the messages will go in a EOIO manner into this queue and gets assigned into the Process Engine.
There is nothing much we can do explicitly on this queue assignment as we also faced the same issue in case of interfaces with BPM where idocs will be flowing into XI in bulk...
Cheers
JK

QRFC Outbound queue errors

Hi All,
I have some "qRFC Outbound queue errors" in the production system of R/3 and the target system is CRM.
The status is "SYSFAIL " .
Can anybody tell me how to solve them.
Regards,
Anindya

HI Anindya,
It's a very simple error. You have to check with your Security System Administrator if the user has included in your profile the authorization object S_RFCACL. Before this you have to define RFC Trusted / Trusting Systems in your Landscape.
Reward Points if helpful
Cheers
Manohar

BDC_CLOSE_GROUP, queue error at

I want to record the transaction MM01, i am on sap4.0 B, the moment i do the recording and click save , it shows a dialog box saying get transaction, then i click on yes, at that moment it throws an error
BDC_CLOSE_GROUP, queue error at . Please check the system log
Can anyone help, is this is a authorization error....???
Or how should i remove this....?
Points will be rewarded

Runal,
Might be you have opend multiple BDC groups and have not closed them properly.
Regards,
Sujatha

Queue error in BPM

Similar Messages

Maybe you are looking for