R2 - Distribution Point not working properly

From my main SCCM R2 server, I went to add an additional server with multiple roles.
I can't tell if it's working properly, however.
For example, the Distribution Point role. I've set it as PXE boot, and our Cisco admin has setup an IP helper accordingly, but when I go to boot a client to PXE, it gets an error "Windows failed to start".
File: \Tmp\x86x64{13902C6F-DD5F-4467-88C9-1BAC44DF8287}.bcd
status: 0xc0000098
Info: The windows boot configuration data (BCD) file from the PXE server does not contain a valid operating system entry. Ensure that the server has boot images installed for this architecture.
From Boot Images on the main SCCM server, I had pushed them to the distribution point. Or so I thought? I mean, the "In Progress" tab says the distribution point server name I'm trying to push it to under the "Device" column. Then
Description reads "Distribution Manager Successfully processed package "Boot Image (x64)" (package ID = STL00005)".
But it's been sitting like that for over an hour...
WDS role is also installed on the DP I'm trying to PXE boot from.
Should I disable WDS and then what do I do in SCCM to get it to PXE boot and make sure the boot file for SCCM is on there?

Nvm I got it up
I removed the WDS server but not the role of the DP in question
I then removed the roles from the server within SCCM console
Then added back only Distribution Point, then I was able to distribute the boot ups to it again, no errors in logs
PXE boot working fine with task sequences
This is what I ran into after getting PXE to not throw DHCP error
http://www.windows-noob.com/forums/index.php?/topic/8836-problems-with-pxe-and-nothing-in-smspxelog/

Similar Messages

SCCM 2012 Distribution Point not working properly on a Windows 2012 Server

I have an SCCM SP1 site running on a Server 2008 R2 machine. I had a couple of distribution points, also running on 2008 machines. These served as DPs and PXE boot points. I had no problems with these.
I resently added a Server 2012 machine, and set it up as a DP, with a PXE boot point. The servers is part of a boundary group containing about 1500 clients. I distributed all of packages that are included in my main task sequence, and am able
to PXE boot, and image machines successfully.
However, I am having problems deploying other packages and Windows update packages from this DP. It seems like I am only able to deploy packages that have the "Copy the content in the package to a package share on distribution points" enabled.
If this is not enabled, the client will get the deployment policy, but will never download the package. The "In Progress" tab for the deployment status will just say "Waiting for content".
I have checked the rereqs for IIS on the Server 2012 DP, also checked the firewall. Everything that I see seems to be OK. Are there other things that I can check to determine why this DP isn't working right?

Hello,
According to the following description, this behavior would be normal:
If you configured the option Run program from distribution point on the
Distribution Points page of the Deploy Software Wizard, do not clear the option
Copy the content in this package to a package share on distribution points, because this will make the package unavailable to run from distribution points.
http://technet.microsoft.com/en-in/library/gg682178.aspx

Pointer not working properly in mozilla browser alone wat to do??????

pointer moves around the page but unable to select using the pointer.each time i had to press backspace to type something on the search box.i cannot get a dropdown box in gmail to sign out because of pointer not working properly.how do i rectify it??????????

You may have switched on caret browsing.
*http://kb.mozillazine.org/accessibility.browsewithcaret
You can press press F7 (on Mac: fn + F7) to toggle caret browsing on/off.
*Tools > Options > Advanced : General: Accessibility: [ ] "Always use the cursor keys to navigate within pages"
*http://kb.mozillazine.org/Scrolling_with_arrow_keys_no_longer_works
*http://kb.mozillazine.org/Accessibility_features_of_Firefox

XFCE4 not working properly display X as cursor not arrow pointer

Hi all
I have recently installed arch and XFCE4 as my desktop environtment everything went well for a few days.
But all sudenl 2 days ago thing appeared not working properly. Things displayed on my desktop are out of proporion mainly the X as cursor instead of an arrow, newly opened windows default to top right cornner overlap my taskbar panel not able to move this. I've tried to re-install xfce4 but weren't sure I did it correctly.
tried :
pacman -Rdd xfce4 xfce4-goodies
rm -R ~/.config/xfce4
then reinstall problem still occurs.
Any suggests and help would be greatly appreciated.
thx
Last edited by archlux (2013-06-23 14:29:01)

Be sure you cursor theme is complete. Which one are you trying to use? Did you try setting it up from directly X confs?
There must be an option in window manager or window manager tweaks about overlapping taskbar. You can use alt+left mouse to move your windows till it is configured.
Reinstalling is as meaningless as deleting system32. If you are out of options, just delete your .config folder then reinstall.?
Last edited by Gulver (2013-06-23 17:59:47)

HP computer will not work properly with an HP printer

I have the following two items that I am trying to use together:
- HP 23" TouchSmart Desktop, T6500 2.1GHz 4GB DDR3, 500GB HDD (Windows 7)
- HP OfficeJet 6500 Multi-Function Printer/Scanner/Fax
When I try to scan to Adobe Acrobat Professional 9.0, the document goes through the scanner, however the dialog box that I would expect (e.g. "Next Page" or "Done") never shows up. At this point, the system is unresponsive with respect to Adobe or the printer.
I suspect that it is waiting for the input from the dialog box that never showed up. I tried to move the other windows to see if the dialog opened in the background, however I am not able to select any of them (they remain frozen).
I contacted HP Support, only to have them tell me it must be the driver, and I have an "old" printer. (I did not realize that a 9 month old printer was considered "old"). I have tried all of the possible drivers that are available (original disk, downloads, other downloads from HP tech support), none of these resolves the problem.
In any case, they were unable to resolve the problem of having an HP computer work properly with an HP printer. (The printing function seems to work, just very slowly).
Has anyone else heard of this? Is there a resolution?

Update: I am still looking for a solution to this problem - the scanning portion of the Multi-function OfficeJet 6500 does not work properly with the HP TouchSmart computer.
I have not been able to find anyone in HP that can tell me when (or if) new drivers will be released for this printer.
I decided to investigate upgrading to a newer version of printer since HP told me the 9 month old printer I have was "obsolete", only to find that the identical printer is still on sale in many stores. Hmmm....
I feel like I am getting the run-around from HP.
I have since tried several more driver/software combinations, but every time I have the same problem (as described in the previous post).
If anyone has any ideas or suggestions, I would be most happy to hear them.
Thank you.

Adobe Photoshop Touch is not working properly on my Samsung Tablet

I just recently downloaded the Photoshop Touch App to my Samsung Tablet. The program will open and some of the tools will work, but MOST tools will not! I have attempted to clear the cashe, uninstall, and then reinstall the program. The problem persists. When will Adobe provide an update with repairs so that I can actually use the App I just bought?

Dear Guido.
We have followed instructions to uninstall and and then reinstall the Photoshop Touch program onto the Samsung Galaxy Tab 3.
It is still not working properly.
NONE of the Fx's are working. (about 26 effects!)
The Fx's under the menu headings of... "Basic" , "Stylize" , "Artistic", or "Photo" do not work!
Under the heading of "Adjustments"... only Invert, and Black and White work... NONE of the others do!
The items that do work are... the Camera Layers, Layers and Selections, Image Blending, and the Basic FX called Gaussian Blur.
Croping image size, text, etc. under the & symbol also work.
So, as you can see....at this point we have purchased an App that is practically USELESS even tho the Google Play Store said that it was compatible with our device.
Please Advise, or Create a proper Update for this device,
Thank you

MRS (Multi resoource scheduling) not working properly

Hello All,
We have MRS 610 installed in our landscape. We have configured it to integrate with Maintenance orders. We are facing an issue as to not all orders are reflected in the planning board though we make exact replica of orders which already exists in the planning board. Those orders which are there in the planning board doesnot reflect the changes that are done to it in PM module. I have checked all the demand related configuration settings and all seems to be fine. The inegration between PM and MRS is not working properly. Orders are getting pulled into the planning board if we run the report /MRSS/SGE_DEM_DATA_MIGRATION.
We recently upgraded to SP4 level. Kindly help me to trouble shoot this issue.
Many thanks in advance.
Boby

Dear Bob
As far as I have understood that your problem is that the backward integration is not happening.
That means whenever you are assigning a resource to the PM Order these alocation are not reflected in PM Order. Just check following points.
1. Check weather you have activated back integration of PM or not !
2. Check this under the node: Sources of Demands->Orders-> Control integration of PM/CS Orders
3. Also make sure that you have activated back integration of demand type R3OR in the node Sources of demand.
4. Check PM Settings related to Work centre
5. Apply the Note 1135513 - MRS: Changes to standard for PM/CS
integration
Also please go through the Documentation supplied with the sofware Installation CD for MRS.
It gives step by step activities how to proced with config.you will have to go through this documentation very thoroughly as all information is avalable .
Also check this link
http://help.sap.com/bp_serv603/ServInd_DE/html/index.htm
This link gives best practices for services industry.
Go To Business Information > Preconfigured Scenarios > (Right hand side )>SAP ERP Scope >Scenarios - by Business Areas>Project Resource Management >Service Order with Resource Scheduling (MRS).
This will serve you as guidance for configuration.
With regards
Mangesh

DirectAccess on Server 2012 R2 with Single NIC behind NAT on IPv4 only Corporate Network Results in "DNS Not Working Properly"

I hit this problem at a customer site and can re-produce it in a simple lab. Lab environment: servers:
1x Server 2012 R2 DC and DNS server - DC1 - 10.0.0.1
1x Server 2012 R2 DirectAccess (DA) server - DA1 - 10.0.0.100
Servers are running "Update" (KB2919355) and following DA hotfixes:
KB2929930
KB2966087
I configured DA (via advanced wizard) as follows:
DA and remote access
AD group
directaccess-webprobehost DNA (A) record pointing to 10.0.0.100
behind an edge device (with a single network adapter)
SSL certificate from enterprise root CA issued to directaccess.contoso.com
NLS on remote server using https://nls.corp.contoso.com
DNS: corp.contoso.com = 10.0.0.1; nls.corp.contoso.com = ""
DNS suffix search list = corp.contoso.com
The DNS server validates successfully in the configuration UI.
With this configuration, I get a static IPv6 address of fd79:7a37:cbd9:3333::1/128 assigned to the NIC
The operations status is all green apart from DNS which displays the following error:
"DNS: Not Working Properly"
Error:
None of the enterprise DNS servers fd79:7a37:cbd9:7777::a00:1 used by DirectAccess clients for name resolution are responding. This might affect DirectAccess client connectivity to corporate resources.
Causes:
Enterprise DNS servers fd79:7a37:cbd9:7777::a00:1 are not responding.
I can, however ping fd79:7a37:cbd9:7777::a00:1 (which is the DNS64 translation of 10.0.0.1)
I would like to know what checks are failing as there are no failures in Event Viewer.
I have come across forums where people have the same issue and fix it by specifying the local IP (in this case 10.0.0.100) as the DNS server, however Richard Hicks has confirmed with me that the DNS server should be set to the DNS server, not the DA server's
IP.

Thanks for the post Matt,
ISATAP has been disabled on my DA server, so the results of a "ROUTE PRINT -6" command yields:
===========================================================================
Interface List
12...00 15 5d 01 03 64 ......Microsoft Hyper-V Network Adapter
1...........................Software Loopback Interface 1
14...00 00 00 00 00 00 00 e0 IPHTTPSInterface
===========================================================================
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
1 306 ::1/128 On-link
12 261 fd79:7a37:cbd9::/48 On-link
14 306 fd79:7a37:cbd9:1000::/64 On-link
14 306 fd79:7a37:cbd9:1000::/128   On-link
14 306 fd79:7a37:cbd9:1000::1/128     On-link
14 306 fd79:7a37:cbd9:1000::2/128    On-link
14 306 fd79:7a37:cbd9:1000:814c:28be:46b5:52c1/128   On-link
12 261 fd79:7a37:cbd9:3333::1/128 On-link
12 261 fd79:7a37:cbd9:7777::/96 On-link
12 261 fe80::/64 On-link
14 306 fe80::/64 On-link
12 261 fe80::20c0:e848:d304:9f01/128   On-link
14 306 fe80::814c:28be:46b5:52c1/128     On-link
1 306 ff00::/8 On-link
12 261 ff00::/8 On-link
14 306 ff00::/8 On-link
===========================================================================
Persistent Routes:
If Metric Network Destination Gateway
0 4294967295 fd79:7a37:cbd9:1000::/64 On-link
0 4294967295 fd79:7a37:cbd9::/48 On-link
0 4294967295 fd79:7a37:cbd9:7777::/96 On-link
===========================================================================

Satellite Pro U200: VGA output not working properly when AC adapter was connected

Hi,
I have a problem with vga output. When I'm working on battery and connect my notebook to external monitor it's ok, but when I connect AC adaptor then start waving also bluetooth and wlan does not work properly. In other case when I remove battery from notebook and connect AC adaptor it works properly.
thanks in advance

As long as you use a CRT you should set the refresh rate new, at least 85Hz. Standard is 60Hz as far as I know, and that hurts in your eyes.
The wireless lan behaviour is quite normal as long as your not right next to the access point. On battery power the wireless lan card reduces its energy consumption thus the connection will be poor if you dont have a perfect signal. You can turn this off in the iNTEL Pro/SET wireless software, where you can configure the adaptor. Try to change the powersafe mode to manual and full power, this should solve your problem.

Routine is not working properly?

Expert's please tell me is there any problem with this routine?
Because this routine is not working properly.It is not populating to all the fields the RESULT value.
if
COMM_STRUCTURE-/BIC/ZVEN_NAME = 'VENDOR1' or
COMM_STRUCTURE-/BIC/ZVEN_NAME = 'VENDOR2'.
result value of the routine
RESULT = 'YEPSILON'.
ELSE.
RESULT = COMM_STRUCTURE-/BIC/ZVEN_NAME.
ENDIF.
Thanks in advance.
vasu.

Vasu,
Here is the sample code which i have tried out in my system: its working properly, please find the same.
$$ begin of routine - insert your code only below this line -
fill the internal table "MONITOR", to make monitor entries
IF
COMM_STRUCTURE-/BIC/YSLSTDP3 = '08.2007' or
COMM_STRUCTURE-/BIC/YSLSTDP3 = '09.2007'.
result value of the routine
RESULT = 200000.
ELSE.
RESULT = COMM_STRUCTURE-/BIC/YSLSTDP3.
ENDIF.
if the returncode is not equal zero, the result will not be updated
RETURNCODE = 0.
if abort is not equal zero, the update process will be canceled
ABORT = 0.
$$ end of routine - insert your code only before this line -
*****Assign Points*****
Thanks,
Gattu

Java Script Code not working properly for visios in sharepoint 2013

Hi all ,
I have few visios and I am using the visio web part to display and to redirect from one visio to other visio I am using the java script code through content editor web part .
In share point 2010 it's working fine , I was able to redirect to all the visios and code is working fine .
In share point 2013 its not the same , Its not working properly . only for the first time the code is working fine . once it goes to next visio the code stops working .
For example if i click in visio A it gets redirect to Visio B and its stops working , it wont allow to do any other steps .
I have checked with the URL its correct , I am not able to find any error also .
Indresh

This will be likely caused by the Minimal Download Strategy not registering the Javascript on the page reload. You can turn off the MDS feature to test this.
You can either turn off MDS in your site, or register your Javascript functions with MDS to ensure they are called. To do this, you'll need all of your code to be wrapped in a javascript file (Embed this on the page using a <script> tag and
inside that file in a function, which you then register with MDS as follows (I usually do this in the first line of the javascript file):-
RegisterModuleInit("/SiteAssets/YourJavaScriptFile.js", NameOfYourFunction);
Regards
Paul.
Please ensure that you mark a question as Answered once you receive a satisfactory response. This helps people in future when searching and helps prevent the same questions being asked multiple times.

Help! My Mouse pad is not working properly. The arrow cannot be controlled, it just keeps jumping all over the page. How can I stop this?

Help! My Mouse pad is not working properly. The arrow cannot be controlled, it just keeps jumping all over the page. How can I stop this?

There are several possible causes for this issue. Please take each of the following steps that you haven't already tried until it's resolved. Some may not apply in your case.
1. Follow the instructions in this support article, and also this one, if applicable. A damaged or defective AC adapter could be the cause, even if it's the right kind.
2. Press down all four corners of the trackpad at once and release. If there's any effect, it's likely to be temporary, and in that case the unit must be serviced or replaced.
3. Open the Bluetooth preference pane in System Preferences and delete all pointing devices other than the trackpad, if applicable. Disconnect any USB pointing devices. By a "pointing device," I mean a peripheral that moves the cursor, such as a trackpad, mouse, trackball, or graphics tablet. A plain keyboard is not a pointing device.
4. Start up in safe mode and test, preferably without launching any third-party applications. If you don't have the problem in safe mode, but it comes back when you restart as usual, stop here and post your results. Do the same if you can't start in safe mode. If there was no difference in safe mode, go on to the next step.
5. Reset the System Management Controller.
6. If you're using a Bluetooth trackpad, investigate potential sources of interference, including USB 3 devices.
7. A swollen battery in a portable computer can impinge on the trackpad from below and cause erratic behavior. If you have trouble clicking the trackpad, this is likely the reason. The battery must be replaced without delay.
8. There's a report that a (possibly defective) Thunderbolt Ethernet adapter can cause the built-in trackpad of a MacBook to behave erratically. If you're using such an adapter, disconnect it and test.
9. There's also a report of erratic cursor movements caused by an external display that was connected but not turned on.
10. If none of the above applies, or if you have another reason to think that your computer is being remotely controlled, remove it from the network by turning off Wi-Fi (or your Wi-Fi access point), disconnecting from a Bluetooth network link, and unplugging the Ethernet cable or USB modem, whichever is applicable. If the cursor movements stop at once, you should suspect an intrusion.
11. Make a "Genius" appointment at an Apple Store to have the machine and/or external trackpad tested.

Key not working properly

I bought E-71 about one month back. I upgraded its software to 110.07.127. After this upgrade process, the keys are not working properly.
For example, the key titled '?' is not printing '?' while another key titled '.' is printing '?'. This problem is for the whole keypad.
FYI, my keypad also contains the Arabic letters. They are also not working after this upgrade.
Software upgrade is done from the following link: http://www.nokia.co.in/A4767968
Thanks a lot in advance for the kind support.
Nabeel ur Rehman
Nabeel ur Rehman
Solved!
Go to Solution.

This has happened because your phone was most likely imported and modified before it was sold you you. Updating the firmware has reset it back to it's default configuration
You need to contact a nokia care point for help getting it back working properly. If the care point isn't an option visit the retailer where you purchased it.
Care points/service centres and repair info:
UK • Europe • Asia-Pacific • USA •
Canada • Middle East and Africa
Elsewhere: Click here, select your country, go to the support section, then select repair.

How do I get "Vanishing Point" to work properly on iMac Retina 5k

How do I get "Vanishing Point" to work properly on iMac Retina 5k? When I "render grid to photoshop" the grid is not in right place and scale. I'm using latest version of CC.

OMG! What a load of crap and thank you for posting this. I spent 3 solid hours to do something that I have done hundreds of times before, apply a Vanishing Point filter. I kept thinking I had some non-default setting on and was literally screaming at my new iMac. I NEVER thought it would be the cause. It was actually easier to reinstall CS5 on an older Mac and just do the stuff I needed. This is crazy. I fully get why Adobe doesn't support this yet but to not make a huge deal out of it so people know about it is just wrong. When I searched for Vanishing Point on the Forums, this thread showed almost the bottom of the first page. It should be stuck to the top until they fix it.

Flashback Reclaimable Does Not Work Properly

We saw the strange behavior of flashback reclaimable space as it does not work properly if the PERCENT_SPACE_USED of v$flash_recovery_area_usage is near to 100 (99.9x). As we are running Oracle 10gR2 (Cluster & RAC) to manage our production RAC database, it is a two node RAC. on IBM AIX 6.1
Today at 9:00 AM, we observed that 97% reclaimable space was available. And db_recovery_file_dest_size is 460 GB out of 600 GB (mount point). No other process is being used this mount point for any IO, it is reserved for flashback only. We left 140 GB space free on mount point to over come any dynamic space requirement for flashback.
At 10:00AM we received out of space message in alert log file and during 9:00 AM to 10:00 AM 10 to 15 archive logs were created and at 9:50AM some archive log were also deleted automatically by oracle server(default behavior). Please see the output below.
FILE_TYPE PERCENT_SPACE_USED PERCENT_SPACE_RECLAIMABLE NUMBER_OF_FILES
CONTROLFILE 0 0 0
ONLINELOG 0 0 0
ARCHIVELOG 99.9 98 1520
BACKUPPIECE 0 0 0
IMAGECOPY 0 0 0
FLASHBACKLOG 0 0 0
It is really a strange behavior, please is there any one who face the same issue or what may be the reason for this ?
regards,
Edited by: user13656883 on Jul 18, 2011 11:27 PM

Dear CKPT,
we daily have 3 times archive log backup and after every backup we do crosscheck. as is mentioned earlier, 99% space was shown as used and but on the other hand 97% space was also shown as reclaimable. so on these bases we are very confused , why oracle behaves like this and throw error in alert log as below
ORACLE Instance rac1 - Archival Error
Mon Jul 18 09:59:08 2011
ORA-16014: log 1 sequence# 39143 not archived, no available destinations
ORA-00312: online log 1 thread 1: '/u02/oradata/rac/redo01.log'
Mon Jul 18 09:59:08 2011
Errors in file /u01/oracle/product/1020/db/admin/rac/bdump/rac1_arc0_3212156.trc:
ORA-16014: log 1 sequence# 39143 not archived, no available destinations
ORA-00312: online log 1 thread 1: '/u02/oradata/rac/redo01.log'
Mon Jul 18 10:04:13 2011
Errors in file /u01/oracle/product/1020/db/admin/rac/bdump/rac1_arc1_3277694.trc:
ORA-19815: WARNING: db_recovery_file_dest_size of 493921239040 bytes is 100.00% used, and has 0 remaining bytes available.
Mon Jul 18 10:04:13 2011
regards,

R2 - Distribution Point not working properly

Similar Messages

Maybe you are looking for