Read AI multiple channels on the same device

Hi,
I'm using the NI PCI-6036E card, and I want to read two of the analogue channels.
I do the AI config and AI start for the two channels right after eachother in a flat sequence struct. I use device "1" for both but the first Ai config gets "AI Channel 00" and the second gets "AI Channel 01". The Task IDs is saved in local variables but they are both the same value, the last one. The AI Read is placed in the main while loop.
How do I configure the VI to read two channels on the same device?
Best regards
/Crister Nilsson

Hi,
It seem by your explanation that you first configure your board with AI Channel 0 and then reconfigure the board to measure AI Channel 1. You should only use one AI config and in the channel input of that VI specify the channel(s) to measure. This tells the board which channels to measure.
Hope this helps
Regards/ Tony

Similar Messages

  • I have a DAQ Assistant configured to read multiple channels at the same time. When I wire a graph indicator to the output, I see all of my signals jumbled together. How do I split them up into seperate signals?

    I have a DAQ Assistant configured to read 2 channels at the same
    time. When I wire a graph indicator to the output, I see the 2
    signals jumbled together. How do I split them up into seperate signals?
    When I wire any type of indicator it is showing just one output of a single channel.
    I want 2 indicators showing 2 different signals as expected from the 2 channels configured. How to do this?
    I have tried using split signal but it end up showing only 1 output from 1 signal in both the indicators.
    thanks in advance.
    Solved!
    Go to Solution.

    Yes you are right. I tried that but I did not get the result.
    I just found the way. When we launch split signal, we should expand it (split signal icon) from above and not from below. It took me a while to figure out this. 
    thanks 

  • Multiple users on the same device

    Can I have 2 or more users on the same device? I want to use a Kindle Fire HD when traveling with separate accounts for my wife and myself.

    You can; you just have to disable automatically signing one of you in (unless you want to constantly log the other one out)

  • How do I run multiple channels in the same VI?

    I am trying to analyze two signals, one temp, the other strain.  I have configured my two tasks using MAX, and written separate VIs which work fine when run independently.  Now I want to measure the two signals and output the data on two separate graphs within one VI, but when I run the VI I keep getting an error stating that the "resource is already reserved" (or something to that effect).  I tried adding a channel to an existing task, and building the VI but that didn't work (both signals showed up on both graphs).  I also tried using two separate tasks but that when I get the aforementioned error.  How do I get each channel to show up on different graphs?
    I am using: M-Series DAQ card 6259, SC-2345 and SCC modules, with Labview 8.0

    Does the following VI come close to what you wanted to do ?
    Attachments:
    demo-signal-split.vi ‏108 KB

  • How do I customize firefox for multiple users on the same device?

    Sometimes my wife uses my computer to surf the web. I'd like to have it set up so she can have her bookmarks, etc. when she's using it and I can have mine when I'm using it. Is this possible? If so how do I do it?

    hello arack, the easiest way would be to create different user accounts for you both on the mac on the level of the operating system: [[How do I share Firefox between people on a computer?]]
    or you could use the firefox profile manager to create separate profiles: [[Use the Profile Manager to create and remove Firefox profiles]]

  • How can I plot multiple channels on the same figure?

    My inputs are:
    x axis : 1-D array
    Y axis : 2-D array consisting of data from several channels, where every row contains data from one channel (1-D array)
    I would like to plot several channels vs one with the legend etc..
    Attachments:
    dummy.vi ‏16 KB

    I have created an example which -
    - takes an independent X axis data
    - takes 2D Y data
    - takes 1D Y data
    Displays all on an XY Graph
    Do Let me know if it helps.
    Sandeep
    Attachments:
    dummy_with_XYGraph.vi ‏46 KB

  • Multiple profiles/users on the same device

    Hi there,
    I know that iOS is a single user environment.
    But, I am currently working in an enterprise environment and I was wondering if it was possible to have several profiles on the same device, maybe using certificates or so?
    Thanks for your help
    Cheers,
    Pierre.

    It would seem that unlike previous iOS devices the iPad and possibly AppleTV call for the ability to enable multiple profiles/users on the same device.
    I would suggest that if this capability is not on the roadmap for iOS by now then there is a least one place where alternatives to the iPad will have a major advantage.
    The thought they I would have to buy multiple iPads one for myself, my wife and my child because of a software constraint is untenable from a ecological standpoint (all these devices end up as landfill) let alone the economic one.
    Also as I use the iPad I see it's potential to become as important computing platform to me as my laptop eventually surpassing it. In this light I can't see how it could remain just a personal device.

  • HT204053 Can multiple people use the same Apple ID for their own devices?

    Can multiple people use the same Apple ID for their own devices? I just set up my IPhone 4S (first time user) using the same Apple ID as my daughters and now we receive each others texts, do I need to set up my own Apple ID account?

    Yes, you can.  In fact it's recommended that you use different IDs for iMessage, FaceTime and iCloud.  You can still share the same ID for iTunes without any issues.
    You are getting each other's text messages because you're using the same ID for iMessage.  To fix this, one of you should go to Settings>Messages>Send & Receive, tap the ID, sign out, then sign in with a different ID.  To avoid getting each other's FaceTime calls, do the same thing in Settings>FaceTime.

  • IOS device failed to get ip address on multiple wlan on the same anchor controller

    Dear Experts:
    in my implementation, we need 2 WLANs be served on the same anchor controller.
    WLAN1: wep/40bit, integration with NAC/OOB on anchor controller for guest wlan service.
    and guest account controlled by NACguest server.
    WLAN2: wep/40bit, no layer3 secuirty for temporary using.
    foreign controller: WiSM on v6.0.196.4 (also testing on 6.0.182.0)
    anchor controller: WLC4402 on v6.0.196.4
    on WLAN1:
    Windows7 client get ip address correctly.
    iOS (iPhone4 on 4.3.1/4.3.2, iPad2 on 4.3.1/4.3.2) can get ip address correctly on WLAN1.
    WLAN2, iOS device cannot get ip address.
    compare with debug message "debug clien mac" + "debug dhcp message enable"
    on both foreign and anchor controller.
    on foreign controller:
    PM state has changed from: DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
    on anchor controller:
    PM state always stay on: DHCP_REQD (7) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
    Enable/Disable DHCP Address Assignment Required is not work.
    Enable/Disable DHCP proxy is not work.
    Any hit this issue when get ip address failed in multiple WLANs on the same anchor controller?
    In attachment log file,
    DMZ.log: anchor controller on DMZ.
    S3p1.log: WiSM on v6.0.182.0
    S3p2.log: WiSM on v6.0.196.4
    client mac: 00:1f:3b:05:33:c1, Windows7 Client
    client mac: 58:55:ca:cf:d2:07, iPhone4 with 4.3.1,
    WLAN1 subnet: 10.61.246.0/23
    WLAN2 subnet: 10.61.248.0/23

    Hi, Nicolas:
    just checking the attachment for the run-config on foreign/anchor controller.
    DMZ_run.config  - anchor controller
    s3p1_run.config - WiSM on v6.0.182.0
    s3p2_run.config - WiSM on v6.0.196.4
    at this moment, we have disable the wlan 10 on foreign controller, and wlan 2 on foreign controller.
    Wilson...

  • Has anyone tried to pair the Tzumi bluetooth headphones to their iMac?  My iMac will detect the device, connect to it for about 2 seconds, then shows a status of "not connected".  Multiple attempts get the same result.

    Has anyone tried to pair the Tzumi bluetooth headphones to their iMac?  My iMac will detect the device, connect to it for about 2 seconds, then shows a status of "not connected".  Multiple attempts get the same result.

    Edge has very clear restrictions, one being that you must have 6 months of clean payment history which you don't. Either wait until April 14, or good luck at Sprint.
    I am unsure how it can be determined the payment mix up was the fault of CS, but regardless, the mix up was done. There can be any number of reasons why a payment could be missed without any fault on your part, however you are still the responsible party for the account and must live with the repercussions.

  • E4200 v2 - Uses multiple MAC addresses for the same device

    This unit seems pretty good at first but on looking at the Web interface I noticed that it was using multiple mac addresses for the same device and showing devices on the lan on the Wireless side and other odd things.
    After a week of running it the home server network started to get erratic, it would seem to all point to dns and dhcp issues in the router.
    Seems the V1 had the same issues that they did not fix on this.
    The Cisco connect software shows 5 devices the Web based utility shows 3??.
    Its pretty bad that they charge nearly $200 and cannot be bothered to finish the unit or address the issues that were in V1.

    I am afraid I didn't get the clear picture of the issue mentioned in the post. Could you please elaborate a little bit? If you connect a device/computer wired and then later you connect it wirelessly. It is obvious that you would get to see two different MAC addresses for the same device, one for the LAN adaptor and other one for WLAN adaptor. If that is what you are referring to?
    Secondly, may I  know, what issues did you face with DNS and DHCP in the router? Is it not able to resolve the DNS or something else or DHCP is not sending IP address to the clients?

  • Installing a LOB App for Multiple Accounts On The Same Surface Device

    Hi,
    When installing apps to iOS & Android there is no concept of a local user account, and an app can only be installed once. For Windows devices, a single device can have multiple accounts. Those accounts can be local or domain and have administrator privileges
    or not.
    We are planning to use the Device Enrollment Manager concept in Intune to enroll approximately 200 non-domain joined devices. Each device will have two local accounts - one in English and one in French. We have a LOB Windows App that works in both
    languages. We do not want the local accounts with the App to have administrative permission.
    It seems you need local administrator permission to enroll the device. If I then install the app from this account, it works. However, I need the app installed on the local English and local French account.
    When I log locally into the device using a standard account and log into the Company Portal, it shows the app as installed. It is not, however, installed for that user and is not accessible. Note that I'm using the same Intune account. It is only available
    to the local administrator account. The only option I have is 'Re-Install'. When I select that, nothing happens - it is stuck in the "Installing..." state.
    If I only enroll the device using the local administrator account and then log into the local standard account to install the app, it doesn't show as installed. When I choose to install it, it gets stuck on Installing.
    I'm missing something here...
    Is it possible to install an App from Intune more than once on a Surface device? Do the Intune accounts need to be unique per-install? Is it possible to install the app without local administrator permission?
    Thank you!
    -jd

    An update. If I:
    Enroll a Windows Surface using a local admin account
    Request to install an app from a local standard account it appears stuck on Installing...
    Log back in as the local admin account and wait, the app appears.
    Questions:
    Can the same app be installed into multiple local accounts on the same device? It doesn't look like it.
    Is the local account used when the device is enrolled the only local account that will install Intune apps?
    -jd

  • Multiple iCloud accounts on same device

    With multiple MobileMe accounts (on the same device), only the 'primary' account would 'push' email. The other accounts would need to manually fetch the email.
    Has this changed with iCloud? If you set up multiple iCloud accounts, will they all have email 'pushed'?
    What about Contacts and Calendars? Will changes get 'pushed' to all accounts or just the primary account?
    If Contacts and Calendar changes are not pushed, how can a device be updated with the latest info? With email, there is usually a 'Get mail' button or at least you can set a schedule so messages will get fetched, but there's no such facility for Contacts and Calendars. So if there's no push, how can they keep in sync?
    I'm hoping that even if email push only works for the primary account, it WILL work for Contacts and Calendars, even on the other 'secondary' iCloud accounts. Can anyone confirm this either way?

    Updating this myself as I have some more information.
    The secondary iCloud accounts seem to get mail pushed to them, even on iOS devices which suggests that iOS 5 now does indeed support IMAP IDLE as I cannot see how this would occur otherwise.
    However, an odd thing has occured on the Mac. A day after setting up the 3 iCLoud accounts, during which time it has all worked perfectly well, this morning OSX has modified all the accounts, all by itself. It has self-created 3 MobileMe accounts, named the same as the iCloud accounts were and those have now all been renamed 'iCloud'. The iCloud accounts now have Mail turned OFF and the new MobileMe accounts have that turned ON. IOW, the new MobileMe accounts have taken over the email duties.
    There's 2 oddities about this, well more than 2 really.
    Why create these new 'email only' accounts as type MobileMe which will soon be entirely defunct?
    Why would it do this at all? Why not just leave the 3 x iCloud accounts, as they were?
    How has it done this all by itself? Shouldn't such account creation be a manual process by the user?
    It doesn't seem to have affected the functionality, but I am at a complete loss as to what is going on here. So if anyone can shed some light on it I'd be grateful.

  • Can I use multiple iPhones on the same iTunes account? e.g. my wife and I each have iPhones

    can I use multiple iPhones on the same iTunes account? e.g. my wife and I each have iPhones

    Yes, you can have as many devices - iPhones, iPods, iPads - as you like using the same iTunes account.

  • Find my Friends : Support for multiple users under the same Apple ID?

    Can multiple users under the same Apple ID use the app to find each other?  My daughter uses my Apple ID with her iPod touch which allows me to monitor her purchases but it seems that only one device under an ID can use the app at a time.  If that is the case then it is a major disadvantage and I will need to go back to using latitude (or Find My iPhone which also allows me to see where all of my devices are at the same time)

    http://isource.com/2011/10/16/how-do-you-set-up-icloud-for-a-family/
    This worked for me.

Maybe you are looking for