Recovering an Switch from bin prompt with empty flash

Dear Experts,
I have a 3560G switch with 48 ports. I had mistakenly reloaded with switch, without taking into consideration of fact that someone has already deleted the flash and saved the config. After reload, when the switch returned to bin prompt, I tried booting it only to get the surprise of flash as already empty:(
As the flash is now empty, is there any way out that I could be able to load the image onto Cisco flash? I need to bring this switch into working condition asap.
Would appreciate any help in this regards.
switch: dir flash:
Directory of flash:/
32513024 bytes available (1024 bytes used)
switch: set
BOOT=c3560-ipbasek9-mz.122-55.SE9.bin
CLEI_CODE_NUMBER=CNMWY00ARB
MAC_ADDR=00:18:19:AD:43:80
MODEL_NUM=WS-C3560G-48TS-S
MODEL_REVISION_NUM=C0
MOTHERBOARD_ASSEMBLY_NUM=73-9358-04
MOTHERBOARD_REVISION_NUM=A0
MOTHERBOARD_SERIAL_NUM=FOC102244SQ
POWER_SUPPLY_PART_NUM=341-0107-01
POWER_SUPPLY_SERIAL_NUM=AZS1021011G
SDM_TEMPLATE_ID=0
SFP_MODULE_BOARD_ASSEMBLY_PART_NUM=73-7757-03
SFP_MODULE_BOARD_REVISION_NUM=A0
SFP_MODULE_BOARD_SERIAL_NUM=CAT10171LR6
SWITCH_PRIORITY=1
SYSTEM_SERIAL_NUM=FOC1022Y2G9
TAN_NUM=800-25428-02
TAN_REVISION_NUMBER=B0
VERSION_ID=V02
switch:
Thanks and Regards,
Adnan

Adnan,
Try this:
switch:dir flash:
switch:flash_init
Switch:load-helper
Switch:boot flash:filename/filename
Ref:
http://www.cisco.com/en/US/products/hw/switches/ps628/products_tech_note09186a0080169696.shtml
https://supportforums.cisco.com/message/3837901#3837901 >> To boot the device from Xmodem --switch:
https://supportforums.cisco.com/thread/2128878 >> To boot the device from TFTP from switch:
http://www.freeccnaworkbook.com/workbooks/ccna/recovering-a-corrupt-cisco-ios-image-on-a-catalyst-switch >>> Good link which explain step by step
HTH
Inayath
************Plz rate if this info is helpfull****

Similar Messages

How to get item stock from bin location with serial numbers?

Dear experts
I want to write query for getting item stock from bin location with serial numbers..
Thank you
Santosh Dhere.

Hi Santosh,
Try this:
SELECT T0.[ItemCode], T5.[DistNumber], T5.[MnfSerial], T5.[LotNumber], T3.[OnHandQty]
, T1.[BinCode], T1.[WhsCode]
FROM [dbo].[OIBQ] T0
INNER JOIN [dbo].[OBIN] T1 ON T0.[BinAbs] = T1.[AbsEntry] AND T0.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBBQ] T2 ON T0.[BinAbs] = T2.[BinAbs] AND T0.[ItemCode] = T2.[ItemCode] AND T2.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OSBQ] T3 ON T0.[BinAbs] = T3.[BinAbs] AND T0.[ItemCode] = T3.[ItemCode] AND T3.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBTN] T4 ON T2.[SnBMDAbs] = T4.[AbsEntry] AND T2.[ItemCode] = T4.[ItemCode]
LEFT OUTER JOIN [dbo].[OSRN] T5 ON T3.[SnBMDAbs] = T5.[AbsEntry] AND T3.[ItemCode] = T5.[ItemCode]
WHERE T1.[AbsEntry] >= (0) AND (T3.[AbsEntry] IS NOT NULL)
UNION ALL
SELECT T0.[ItemCode], T5.[DistNumber], T5.[MnfSerial], T5.[LotNumber], T0.[OnHandQty]
, T1.[BinCode], T1.[WhsCode]
FROM [dbo].[OIBQ] T0
INNER JOIN [dbo].[OBIN] T1 ON T0.[BinAbs] = T1.[AbsEntry] AND T0.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBBQ] T2 ON T0.[BinAbs] = T2.[BinAbs] AND T0.[ItemCode] = T2.[ItemCode] AND T2.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OSBQ] T3 ON T0.[BinAbs] = T3.[BinAbs] AND T0.[ItemCode] = T3.[ItemCode] AND T3.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBTN] T4 ON T2.[SnBMDAbs] = T4.[AbsEntry] AND T2.[ItemCode] = T4.[ItemCode]
LEFT OUTER JOIN [dbo].[OSRN] T5 ON T3.[SnBMDAbs] = T5.[AbsEntry] AND T3.[ItemCode] = T5.[ItemCode]
WHERE T1.[AbsEntry] >= (0) AND (T2.[AbsEntry] IS NULL AND T3.[AbsEntry] IS NULL)
UNION ALL
SELECT T0.[ItemCode], T0.[SRNDistNumber], T0.[SRNMnfSerial], T0.[SRNLotNumber], T0.[IBQOnhandQty] - T0.[OnHandQty]
, T0.[BinCode], T0.[WhsCode]
FROM (
SELECT T0.[BinAbs], T0.[ItemCode], MAX(T0.[OnHandQty]) AS 'IBQOnhandQty', SUM(T2.[OnHandQty]) AS 'OnHandQty', N'' AS 'BTNDistNumber', N'' AS 'BTNMnfSerial'
, N'' AS 'BTNLotNumber', N'' AS 'SRNDistNumber', N'' AS 'SRNMnfSerial', N'' AS 'SRNLotNumber', MIN(T5.[AbsEntry]) AS 'AbsEntry', MIN(T1.[BinCode]) AS 'BinCode'
, 10000044 AS 'SnbType', MIN(T5.[AbsEntry]) AS 'BTNAbsEntry', MIN(T5.[AbsEntry]) AS 'SRNAbsEntry', MIN(T1.[WhsCode]) AS 'WhsCode', MIN(T1.[SL1Code]) AS 'SL1Code'
, MIN(T1.[SL2Code]) AS 'SL2Code', MIN(T1.[SL3Code]) AS 'SL3Code', MIN(T1.[SL4Code]) AS 'SL4Code', MIN(T1.[SL1Abs]) AS 'SL1Abs'
, MIN(T1.[SL2Abs]) AS 'SL2Abs', MIN(T1.[SL3Abs]) AS 'SL3Abs', MIN(T1.[SL4Abs]) AS 'SL4Abs'
FROM [dbo].[OIBQ] T0
INNER JOIN [dbo].[OBIN] T1 ON T0.[BinAbs] = T1.[AbsEntry] AND T0.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBBQ] T2 ON T0.[BinAbs] = T2.[BinAbs] AND T0.[ItemCode] = T2.[ItemCode] AND T2.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OSBQ] T3 ON T0.[BinAbs] = T3.[BinAbs] AND T0.[ItemCode] = T3.[ItemCode] AND T3.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBTN] T4 ON T2.[SnBMDAbs] = T4.[AbsEntry] AND T2.[ItemCode] = T4.[ItemCode]
LEFT OUTER JOIN [dbo].[OSRN] T5 ON T3.[SnBMDAbs] = T5.[AbsEntry] AND T3.[ItemCode] = T5.[ItemCode]
WHERE T1.[AbsEntry] >= (0 ) AND (T2.[AbsEntry] IS NOT NULL)
GROUP BY T0.[BinAbs], T0.[ItemCode]
UNION ALL
SELECT T0.[BinAbs], T0.[ItemCode], MAX(T0.[OnHandQty]) AS 'IBQOnhandQty', SUM(T3.[OnHandQty]) AS 'OnHandQty', N'' AS 'BTNDistNumber', N'' AS 'BTNMnfSerial'
, N'' AS 'BTNLotNumber', N'' AS 'SRNDistNumber', N'' AS 'SRNMnfSerial', N'' AS 'SRNLotNumber', MIN(T4.[AbsEntry]) AS 'AbsEntry', MIN(T1.[BinCode]) AS 'BinCode'
, 10000045 AS 'SnbType', MIN(T4.[AbsEntry]) AS 'BTNAbsEntry', MIN(T4.[AbsEntry]) AS 'SRNAbsEntry', MIN(T1.[WhsCode]) AS 'WhsCode', MIN(T1.[SL1Code]) AS 'SL1Code'
, MIN(T1.[SL2Code]) AS 'SL2Code', MIN(T1.[SL3Code]) AS 'SL3Code', MIN(T1.[SL4Code]) AS 'SL4Code', MIN(T1.[SL1Abs]) AS 'SL1Abs'
, MIN(T1.[SL2Abs]) AS 'SL2Abs', MIN(T1.[SL3Abs]) AS 'SL3Abs', MIN(T1.[SL4Abs]) AS 'SL4Abs'
FROM [dbo].[OIBQ] T0
INNER JOIN [dbo].[OBIN] T1 ON T0.[BinAbs] = T1.[AbsEntry] AND T0.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBBQ] T2 ON T0.[BinAbs] = T2.[BinAbs] AND T0.[ItemCode] = T2.[ItemCode] AND T2.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OSBQ] T3 ON T0.[BinAbs] = T3.[BinAbs] AND T0.[ItemCode] = T3.[ItemCode] AND T3.[OnHandQty] <> 0
LEFT OUTER JOIN [dbo].[OBTN] T4 ON T2.[SnBMDAbs] = T4.[AbsEntry] AND T2.[ItemCode] = T4.[ItemCode]
LEFT OUTER JOIN [dbo].[OSRN] T5 ON T3.[SnBMDAbs] = T5.[AbsEntry] AND T3.[ItemCode] = T5.[ItemCode]
WHERE T1.[AbsEntry] >= (0 ) AND (T3.[AbsEntry] IS NOT NULL)
GROUP BY T0.[BinAbs], T0.[ItemCode]
) T0
WHERE T0.[IBQOnhandQty] > T0.[OnHandQty]
Regards,
JC.

PowerPivot refresh error with data feed from sharepoint list with empty exception information

Hi,
My Powpivot refreshing error seems to be different from what others already experienced.
Scenario:
Constructed an external data source in the format of Http://<server_IP>/sites/<mysitecollection>/_vti_bin/listdata.svc
selected one table with some of the needed columns in the next step
Create calculate colums etc.
Create pivot tables etc.
All worked well offline
Upload the workbook into PowerPivot Gallery
Reference it from a page through Excel Web Service webpart allowing manual refresh
The refresh always reports failure with the named external data source
I opend the log file in C:\Program Files\Common Files\microsoft shared\Web Server Extensions\15\LOGS and located the following error messages:
ASPPHOST::ShowEngineError: Out of line object 'DataSource', referring to ID(s) 'f8939b694cae', has been specified but has not been used。The following exception occurred while the managed IDbCommand interface was being used: .
Please note in the above message, NO detailed exception message was given. In other words,
the exception information is empty.
I checked as many things as I possibly could includin the security accounts etc. All seem to be right. But this empty exception got me stuck here.
What could possibly go wrong? Any help will be appreciated.
Thanks.

Hello,
Here is a good article regarding Where to get information about data refresh failures for your reference, please see:
http://social.technet.microsoft.com/wiki/contents/articles/3870.troubleshooting-powerpivot-data-refresh.aspx
In addition, which credential option you're configured for the PowerPivot data refresh in SharePoint farm? You can go through the following articles regarding configure the PowerPivot data refresh:
Configure the PowerPivot Unattended Data Refresh Account (PowerPivot for SharePoint):
http://technet.microsoft.com/en-us/library/ff773327.aspx
Configure Stored Credentials for PowerPivot Data Refresh (PowerPivot for SharePoint):
http://technet.microsoft.com/en-us/library/ee210671.aspx
Hope this helps.
Regards,
Elvis Long
TechNet Community Support

Recovering Photo's from lost Iphone with same apple ID?

I lost my Iphone a while ago,
then 6 months later my laptop crashed and could not be recovered (where my storage was of photo's etc)
anyway, I purchused a new iphone and i have the same apple id and itunes id.
I was wondering if I would be able to get back any of the photo's that were on my iphone that was stolen? like if icloud would of backed them up online or itunes or something like that?
thanks

Photo Stream only holds 30 days of photos on the server. See as you lost your iPhone over 6 months ago Photo Stream won't help. If you have a backup of the phone before it was lost you can restore that backup to a new iOS device and retrieve whatever was in the Camera Roll at the time the backup was made.
I assume you have no backup of your computer.
Just because the laptop doesn't boot doesn't mean information can't be retrieved from the hard drive.
3 Ways to Recover Data from the Hard Drive of a Dead Laptop

How can I recover images deleted from my vault with Time Machine

My vault died and with it one of my projects within the vault. The other images plus some new ones are in the vault ok but I am slightly worried about reinstating my Aperture library and not just focusing on the missing project and images. BUT there appears to be no way of seeing the files within the Aperture library. I would welcome some advice about this. Thanks

This must be a tough one, I can actually hear the birds chirping

HELP! Recover lost array from X serve with windows server

We have an Xserve raid with two 7 drive arrays mounted as one drive on a windows sever 2003. We lost one array and the second array started rebuilding when disk was reinserted. The disks in the first now show as "spare" and the Windows equivalent disk number now shows as "missing" and failed. However disk 0 which is array #2 shows online but failed. The question is--- Do we have any data left on the second array since it rebuilt? Do we try to rebuild the first array hoping Windows will "find" the missing drive? Can we restore the array somehow since retore in disk utility is greyed out? Any advice would be appreciated.
Thanks

We have an Xserve raid with two 7 drive arrays
mounted as one drive on a windows sever 2003. We
lost one array and the second array started
rebuilding when disk was reinserted.
This sounds like you're using RAID 50 (lots of people use it not knowing how easy it is to lose all your data in an instant). You said 'we lost one array' - if that's true, then it's time to nuke and pave - you won't get any of your data back.
MacBook Pro Mac OS X (10.4.6)

How to recover lost contacts from address book with isync.

Hi everyone,
I've just lost all my contacts even in my Nokia N95 when I use iSync. I've deleted my contacts manually in my address book to make a refresh sync with my Nokia. After I conected again and start sync, it deleted all my contacts on my Nokia... I am very dissapointed and angry with Apple.
Can you guys help me bring back my 500 contacts in my address book so I can put back in my Nokia as well?
Thank you in advance.
Matt

Not to my knowledge. As I see it you now are in a position of manually recreating you contact list or as I previously suggested engage a professional in data recovery with no guarantee of 100% or any recovery.
I wish it were otherwise.
Ciao.

Computer text comes up when i try to print a document from my mac with a flash drive to another computer. how do i change that?

Computer text comes up when I try to save a document on a flash drive and print it on another computer that's not a mac. how do i change this?

Please post the computer text.

Test Execution hangs while executing a test from Command prompt option

I have done the following
1) Created a script Test driver
2) Added different scripts as Script->Properties->Assets to the driver script
3) Call each of this asset script from TestDriver using command getScript("<<ScrptName>>".run(1, true, true, true);
4) Now calling this TestDriver script from command prompt with command
e:\\OracleATS\\agent
runScript.bat E:\\INTEGRATION_SERVICES\\Identity_management\\Automation\\Scripts\\MasterScripts\\TestDriver
TestDriver.jwg
The script execution hangs at "Initializing VU 1 for Script TestDriver. After few mintues of seeing this message i get error "Execution Timed Out".
Do I need to keep openscript UI open for script execution from command line ?
Is there any way to increase this Execution Time out ? May be it is taking time to load the internal script assets. AS other scripts are running fine on the same machine from command prompt itself.
Complete error is as follows
C:\Documents and Settings\oracle>e:\\OracleATS\\agent\\runScript.bat E:\\INTEGRATION_SERVICES\\Identity_management\\Automation\\Scripts\\MasterScripts\\TestDriv
er\\TestDriver.jwg
Running "TestDriver" ...
Agent started. Available commands:
stop - Stop the virtual user after it finishes the current iteration.
abort - Abort the virtual user cleanly, before it finishes the current itera
tion.
exit - Terminate the process immediately
You may type the above commands at any time.
12:17:53,418 INFO [1] Initialized script service "oracle.oats.scripting.modules.utilities.api.UtilitiesService"
12:17:53,418 INFO [1] Initialized script service "oracle.oats.scripting.modules.browser.api.BrowserService"
12:17:53,418 INFO [1] Initialized script service "oracle.oats.scripting.modules.functionalTest.api.FunctionalTestService"
12:17:53,465 INFO [1] Initialized script service "oracle.oats.scripting.modules.webdom.api.WebDomService"
12:17:53,856 INFO [1] Initialized script service "oracle.oats.scripting.modules.datatable.api.DataTableService"
12:17:53,856 INFO [1] Initializing VU 1 for script TestDriver
Execution Timed Out.

Hi e_raja_sekar,
You wrote:
public static void main(String args){should be
public static void main(String args[]){Granted, the below code was tested on Windows XP using J2SE SDK 1.4.1_02 (and not 1.2.2 like Sridhar is using), but when I compiled and executed this code:
public class BadMain {
public static void main(String args) {
System.out.println("Hello World");
}The output I got was:
Exception in thread "main" java.lang.NoSuchMethodError: mainSo I don't think this is Sridhar's problem (but I could be wrong) since he says that he gets no error message.
Cheers,
Avi.

I switched from an iPhone to a Galaxy s4. Everything seems ok except text messaging with people who have an iPhone. I can send them a text, they can see it, but I cannot see what they text back. What can I do please?

I just switched from an iPhone to a Galaxy 4S and I like it except for text messaging. I can text, they can see it, but I cannot see their response if they are using an iPhone. Can you help me with this? What do I do please?

Congratulations on your new phone kathdogg! Now let's get your messaging working correctly. If you still have your old device, turn it on, go to settings, and turn off iMessaging.
If you are no longer in possession of your old device, you will need to remove your phone number from your Apple Support Profile. This can be done here: http://bit.ly/1cst2SC
Please keep us posted, and let us know if this resolves your issue!
Thank you,
MichelleH_VZW
Follow us on Twitter @VZWSupport

Switching from shared Apple ID to separate Apple IDs with Family Sharing?

My family (me, wife and 2 kids) all share the same Apple ID. We share it for everything (App Store, iCloud, etc.). We did this because I didn't want to purchase the same music or apps multiple times. This has worked well for several years. But with iOS 8, we can use Family Sharing, but not if we share an Apple ID (at least not when using a shared Apple ID on iCloud). So my question is, how do we switch from a shared account to separate accounts using Family Sharing, while not losing access to any apps or music? I've seen many previous posts (pre-iOS 8) state that I can create new Apple IDs for my wife and 2 kids, then just use them for iCloud and leave the App Store associated with our existing shared Apple ID, but then when they go to update apps, they'll need to enter my password (which my kids do not know, since they don't currently need the password to updates apps with the shared Apple ID. When they want to purchase a new app, be it free or paid, they have to come to my wife or me to enter the password.)
What I'm think is this. Let me know if this would work:
1) Create new Apple IDs for my wife and kids.
2) Before changing anything on their iPhones, go into my phone (which will remain on our existing Apple ID) and turn on Family Sharing and add them to my family so we can share purchases.
3) Once Family Sharing is enabled, change their iCloud login to their new Apple ID accounts. That enables Family Sharing on their devices and they'll be part of my family.
None of the above steps solves for the "you must enter Dad's Apple ID password to update your apps" problem. So my question is, should I also change their App Store account to their new Apple IDs as well? If you say that won't help (because apps will always be associated with the Apple ID they're originally purchased with), then I don't understand how Family Sharing works when you buy apps. In other words, will Family Sharing enable us to share apps that we already downloaded, or just new apps?
Thanks for any help you can provide.
Jason

You should be able to have purchases from more than one Apple ID on one device (up to five I think). When you create the new Apple ID and just leave the apps already on the ipad alone, you shouldn't have any problems.

Is it possible to recover my data from iCloud backup without working wifi? I have as many other upgraded my iPhone 4S to iOS 7.0.2 with the result that the Wi-Fi or Bluetooth no longer works. However, i can connect to iTunes via cable but there is wrong v

Is it possible to recover my data from iCloud backup without working wifi? I have as many other upgraded my iPhone 4S to iOS 7.0.2 with the result that the Wi-Fi or Bluetooth no longer works. However, i can connect to iTunes via cable but there is wrong version of backup.

Answer is no.
If you want the iCloud backup you have to have n internet connection, thus WiFi.
The not working WiFi has happened with quite a number of users.
It is not exactly clear what is the cause but there are suggestions to clear it up:
Some people have had success by removing an apostrophe from the iPhone name. If your iPhone is called something like “John’s iPhone” then this might work. Go to Settings > General > About > Name and change it to something with no apostrophe.
Some people have reported success by putting the iPhone into Airplane mode and then going to Settings > General > Reset > Reset Network Settings, but the problem may return.
You could also try going to Settings > Control Center and disable Access on Lock Screen then turn your iPhone off and on again.
Make sure that your router firmware is up to date.
Try backing up your iPhone and then restoring it. Check how to factory reset an iPhone for details.
If nothing is working for you, try contacting Apple or take your iPhone into an Apple Store.
Succes, Lex

I've broke my phone, it won't switch on, is there any way to recover the data from it?

My phone has split up the side after I dropped it down some concrete stairs and now it won't switch on, so I need to know if there is anyway to recover the data from it, such as phone numbers, photo's etc. Anyone had this problem?
I've tried plugging it in to the computer but it doesn't do anything, and tried plugging it in to the wall to see if that will switch it on, but nothing.
Any help gratefully received! Steve

If it will not turn on - you have zero chance of getting anything off the phone.

Problems with project when switched from Labview 8.2.1 to Labview 10

Hi everyone,
I recently switched from Labview 8.2.1 to Labview 10.
Before I can run the project I get the error which you can see in the attachment.
(The project is running well in Labview 8.2.1)
I did already check if variables end with a space, but none of them are.
The variables are also without any slashes, so that couldn't be the problem either.
Does anybody has any idea what the problem can be, please let me know.
I hope to hear from some of you soon.
Regards,
Kenny
Attachments:
Error Labview 10.JPG ‏19 KB

Your other post in the other thread indicates you've looked at that thread. Based on that have you checked your variable names to see if any of them are multi-line? The error message is basically telling you that you have illegal characters. A carriage return (\r) or a new line (\n) is an illegal character.

Sound problems with Yosemite when switching from internal speakers to earbuds

After upgrading to Yosemite on my Macbook Pro, when I switch from using the internal speakers for sound and plug in my (Apple) earbuds, the sound stops working. The sound also stops when I do the reverse and unplug my earbuds, nothing comes out of the internal speakers. The only way to restore sound is to go into System Preferences, Sound, and select the output device (internal speakers, earphones, etc..). Anyone else experiencing this problem after installing Yosemite, or know of a fix?

I have the same problem..
there is something else happened twice with me, I plugged my macbook with a HDMI cable to the TV, and everything was ok, until I closed the macbook (sleep mode), when I opened the mac again,, the sound has gone! No sound from TV or macbook,, the only solution is to "RESTART"

Recovering an Switch from bin prompt with empty flash

Similar Messages

Maybe you are looking for