REG EXPORT HKLM\System\CurrentControlSet - error on windows
I am testing a windows driver software. When the test fails, I have to attach registry data to the bug.
I get "ERROR: Unable to write to the file. There may be a disk or file system error."
when I run the following command
REG EXPORT HKLM\System\CurrentControlSet (I am running the command in Administrator mode).
This happens very infreqently. Can this be caused by driver software?
What happens if you run regedit and export from there?
For the hardware development I'd ask them over here.
Windows Hardware Testing and Certification
Regards, Dave Patrick ....
Microsoft Certified Professional
Microsoft MVP [Windows]
Disclaimer: This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.
Similar Messages
-
System restore error in windows 8.1
The restore point could not be created for the following reason:
Access is denied.(0x80070005)
Windows 8.1
have tried :
deleted all previous
disabled etcproperties, all to administer, user, everyone
I am the only on my pc- it is a desktop 64 bit.Hi,
Please see this blog
Common causes and solutions to Backup, System Restore, and Complete PC Backup problems - updated!
http://blogs.technet.com/b/filecab/archive/2008/03/12/common-causes-and-solutions-to-backup-system-restore-and-complete-pc-backup-problems-updated.aspx
File Backup
File Backup fails with the following error:
Access is denied. (0x80070005)
This error occurs because the recovery partition is enabled for File Backup or System Restore and is almost full.
To work around this, do not select D:\ as a backup source. Also, go to System Protection in Control Panel and make sure that D:\ is not enabled for restore points.
For the access denied issue,
To find out exactly what directory/registry setting is getting access denied, you could run Process Monitor and then during the backup and look at the log file to see if you find Access Denied.
Process Monitor
http://technet.microsoft.com/en-in/sysinternals/bb896645.aspx
Yolanda Zhu
TechNet Community Support -
System Update Error on Windows XP 64 bit
When I try to run System Update on my T410 which I have just installed Windows XP 64 bit on, I get the following error message.
Searching for Updates
An error occurred while gathering user information.
System Update does nothing after that.Hello,
I don't believe that Lenovo ever shipped a T410 with Windows XP Professional 64-bit Edition, so you'll likely need to manually download device drivers for the various hardware components from the various silicon manufacturers' web sites (i.e., Intel, nVidia and so forth).
Regards,
Aryeh Goretsky
I am a volunteer and neither a Lenovo nor a Microsoft employee. • Dexter is a good dog • Dexter je dobrý pes
S230u (3347-4HU) • X220 (4286-CTO) • W510 (4318-CTO) • W530 (2441-4R3) • X100e (3508-CTO) • X120e (0596-CTO) • T61p (6459-CTO) • T43p (2678-H7U) • T42 (2378-R4U) • T23 (2648-LU7)
Deutsche Community Comunidad en Español Русскоязычное Сообщество -
How to fix system scan error on Windows 8?
sfc /scannow has verification 52% completed.
It says "Windows Resource Protection found corrupt files but was unable to fix some of them. Details are included in the CBS.Log windir\Logs\CBS\CBS.log. For example C:\Windows\Logs\CBS\CBS.log. Note that logging is currently not supported
in offline servicing scenarios."
I try to open the log file, but it says access is denied even though I am logged on as an administrator.
This is an Acer Aspire E1-531 laptop, no operating system DVD came with it. I would try to avoid system recovery if possible. Please help! Doing system recovery I would at least have to re-install all the third-party software including
Microsoft Office which takes time.Healee
I think the "for best performance" may be misleading. I just removed mail for the lock screen apps and afaik it still remained live. I didnt see anything in CBS that pointed to the lock screen problem but if SFC cant finish (it seemed
like it terminated prematurely because of a power setting in auto shutdown) it should eventually be repaired.
You should eventually get an OS dvd (for emergencies if nothing else) and that can be used to do a repair install.
I am wondering if a change in group policy or a malware application might be the reason for the locked screen. You do have admin rights on your user right?
BTW there is a good KB article on SFC and how to read the CBS.LOG file here
http://support.microsoft.com/kb/929833
Wanikiya & Dyami--Team Zigzag -
Attempted to perform an unauthorized operation error on windows 8.1 while installing SQL server 2008
Hi,
I am getting the error "Attempted to perform an unauthorized operation" on windows 8.1 while installing
SQL server 2008.
The specific error is The error is Attempted to perform an unauthorized operation."
at stepSqlBrowserConfigAction_install_ConfigNonRC_Cpu32 .
I have tried everything from copying to the C drive. I am the admin on the machine. I also checked access in registry. It already has acesss to HKLM\System\CurrentControlSet\Control\WMI\security
Can someone comment on how to resolve this issue. I also tried NT
AUTHORITY\SYSTEM but getting the same error.
Any help would be appreciated.Hello,
Please note that SQL Server 2008 requires Service Pack 3 (SP3) to make it compatible with
Windows 8.1. Please perform an slipstream installation of SQL Server 2008 + SP3:
http://support.microsoft.com/kb/955392
If it fails again, please share with us the Summary.txt log file and the details.txt log file. The following article
may help you locate those files on disk::
http://msdn.microsoft.com/en-us/library/ms143702(v=sql.100).aspx
Hope this helps.
Regards,
Alberto Morillo
SQLCoffee.com -
Hello everyone.. I recently bought iPad air and I am trying to connect it to my windows 7 notebook. And so I am trying to install itunes in windows 7. But I keep on getting the error message:
"\SYSTEM\CurrentControlSet\Services\Bonjour Service\Parameters. Verify that you have sufficient access to that key, or contact your support personnel."
I already did this: http://blogs.msdn.com/b/astebner/archive/2006/09/04/739820.aspx that was given in this thread:
https://discussions.apple.com/thread/1558225?tstart=0
But unfortunately I still get the error message during installation. If I ignore that and continue installation, iTunes is installed and seems to work. But my windows does not recognize my iPad. I read somewhere that iPad driver is in iTunes.
Please help... thank you very much.iPad not appearing in iTunes
http://www.apple.com/support/ipad/assistant/itunes/
iOS: Device not recognized in iTunes for Mac OS X
http://support.apple.com/kb/TS1591
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
iTunes for Windows: iTunes can’t contact the iPhone, iPad, or iPod software update server
http://support.apple.com/kb/ts1814
iTunes for Windows: Device Sync Tests
http://support.apple.com/kb/HT4235
IOS: Syncing with iTunes
http://support.apple.com/kb/HT1386
Apple - Support - iPad - Syncing
http://www.apple.com/support/ipad/syncing/
iTunes 10.5 and later: Troubleshooting iTunes Wi-Fi Syncing
http://support.apple.com/kb/ts4062
iOS: “Not enough free space” alert when trying to sync
http://support.apple.com/kb/ts1503
You may need to delete iTunes on your computer and then reinstall.
How To Completely Uninstall and Remove All Traces of iTunes
http://zardozz.com/zz/2008/04/how-to-completely-uninstall-and-remove-all-traces- of-itunes.html/
Cheers, Tom -
Export for system copy fails - Error 9 (Bad file number)
Hello all,
I am attempting to perform the export phase for a hetergenous system copy on our BI system (BI 7.0 - NW2004s). This system runs on HP-UX 11.11 using Oracle 10.2.0.2 and will be migrated to Windows Server 2003 and MS SQL Server 2005, once the export is complete.
While running sapinst to export the data from the source system, there are several input dialog screens that are skipped, which means I am not able to enter all the paramters used for the export. After seeing this behavior from sapinst, I reviewed the sapinst.log and sapinst_dev.log files and find the warning/error "System call failed. Error 9 (Bad file number)". I have included a portion of these files below.
I have reviewed notes 546006 and 583861, but these seem to refer to an Oracle error ORA-27121, but I am not receiving any Oracle errors in sapinst.log or the Oracle alert log. I have looked for possible permission or ownership problems with any of the SAP or Oracle files, but have not found any that were incorrect. Also, these errors do not specify which file sapinst is having problems with, so I do not have a specific file or area to check.
If anyone has seen something similar to this and has any suggestions, I would greatly appreciate any help.
sapinst.log details:
INFO 2009-02-14 15:15:51.67
Execute step collect of component |NW_Export|ind|ind|ind|ind|0|0|NW_GetSidFromProfiles|ind|ind|ind|ind|1|0|NW_readProfileDir|ind|ind
|ind|ind|0|0
INFO 2009-02-14 15:15:52.737
Account bwpadm already exists.
WARNING 2009-02-14 15:15:52.747
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
INFO 2009-02-14 15:15:52.757
Account 0 already exists.
WARNING 2009-02-14 15:15:52.777
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
INFO 2009-02-14 15:15:52.777
Account 200 already exists.
WARNING 2009-02-14 15:15:52.827
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
INFO 2009-02-14 15:16:04.937
Creating file /tmp/sapinst_instdir/NW04S/LM/COPY/ORA/EXP/CENTRAL/AS/EXP/ypcat.log.
INFO 2009-02-14 15:16:05.007
Output of ypcat passwd.byname is written to the logfile ypcat.log.
sapinst_dev.log details:
TRACE 2009-02-14 15:15:52.737
2009-02-14 15:15:52.743 NW._getSAPMount() done: /sapmnt
INFO 2009-02-14 15:15:52.737 [syuxcaccmg.cpp:227]
bool CSyAccountMgtImpl::isExisting(ISyAccountMgt::eAccountType accountType, iastring sName)
Account bwpadm already exists.
TRACE 2009-02-14 15:15:52.747 [syuxcuser.cpp:1943]
CSyUserImpl_getOsInfos(ILogBook *m_logBook, iastring sName, iastring sID, tSyUserInfo& msUserinfo)
getspnam(bwpadm) returned NULL.
WARNING 2009-02-14 15:15:52.747 [syxxsyshlp.cpp:78]
syslib::printOSError(const iastring &, int, DWORD, const iastring &, CMessage::eLogMessage)
System call failed. Error 9 (Bad file number) in execution of system call 'getgrent' with parameter (), line (292) in file (syuxcuse
r.cpp).
Regards,
Rusty RobbinsHello Peter,
Thanks for the reply. I did confirm the points you made, and have the details below.
1. check filesystem, if you have enough space, especially /tmp
All filesystems have available space, and /tmp has 310 MB available, before the start of sapinst.
2. check again alert log, trace log for Oracle,
I could not find any errors in the alert_SID.log or any unusual trace files.
3. How did you run sapinst? Are you using "root" account.
I am running sapinst as user root and I am following all the recomendations in the system copy guide (at least as far as I can tell. ;p )
We have four BI systems in this landscape, and the other three have migrated successfully. The procedure I am using, is the same as for the other 3 systems and uses the same SAP media directory that was used on the other systems.
One other item that may be part of my problem here, is that this system is the production system, and was originally installed as a high-availability system, using HP-UX Service Guard for clustering. Currently, this system does not have fail-over enabled, but of course the cluster is still intact. One required piece of the Service Guard enviornment is the use of a virtual hostname. This seems to resolve successfully by sapinst, as I see the correct (virtual) hostname referenced several times. While this is a clustered system (for fail-over purposes), the CI and DB are installed on the same host. So it is not a distributed system, and if failover had been initiated, it would fail both the CI and DB instance, which is the same and only SAP instance.
This did raise one question in my mind, however. I am attempting to extract this using the following menu path within sapinst.
SAP NetWeaver 7.0 Support Release 3 --> Software Life-Cycle Options --> System Copy --> Oracle --> Source System Export --> Central System --> Based on AS ABAP and AS Java
Since this does use Service Guard, but is not a distributed system, should I be using a different path in the sapinst tree, for the export? I have only performed a migration using the above path, so I am not familar with the detailf of the other types, such as High-Availabitly or Distributed-System.
Regards,
Rusty -
System Update 4 on Windows 7 64bit - An error occurred while gathering user information
Dear all,
I installed System Update 4 on Windows 7 64bit (X300 laptop) and keep getting "An error occurred while gathering user information" at about 9% of Searching for agent updates.
I tried searching Google and this forum for possible solutions, but without much success. I would appreciate any help on this.
Thanks in advance!Hi,
in this situation try following:
open registry:
HKLM\Software\Wow6432Node\Software\Lenovo\System Update\Preferences\UCSettings\RunTime
check if the informations are correct.
In case not, then correct them.
- Try to run TVSU as Administrator (right-click on it and select Run as Administrator)
In case this will be of no use, then just go into the install folder of TVSU and there you will see the folder called "Logs". In there you will for sure find the exact information on what went wrong. Perhaps some proxy config, or just the server was unavailable.
Cheers -
I received the following iTunes error after installing itunes as an adminstrater on my computer using a 64 bit and windows 8.1 operating system: If you wish to import or burn CDs, you need to reinstall iTunes.
I tried the installation trouble shooter and received the following error: Could not write Value ManageLLRouting key\system\currentcontrolset\services\BonjourService\Parameters.
How can I fix Could not write Value ManageLL Routing Key error and install iTunes correctly? Must I uninstall Norton 360 degrees Antivirus program before installing iTunes.
I look forward to your tecniical support .
Cheers,
clinton86Hi clinton86,
Welcome to the Apple Support Communities! I understand that are receiving an alert when trying to import a CD to iTunes and are being asked to reinstall iTunes. iTunes and all of its components must be removed in a specific order when uninstalling from a Windows computer. Please use the following article as a reference.
Removing and reinstalling iTunes and other software components for Windows Vista, Windows 7, or Windows 8
http://support.apple.com/kb/ht1923
1. Remove iTunes and related components from the Control Panel
Use the Control Panel to uninstall iTunes and related software components in the following order and then restart your computer:
iTunes
Apple Software Update
Apple Mobile Device Support
Bonjour
Apple Application Support (iTunes 9 or later)
Important: Uninstalling these components in a different order, or only uninstalling some of these components may have unintended affects.
I hope this helps,
-Joe -
What do I do when I get an error message: Could not write value ManageLLRouting to key\SYSTEM\CurrentControlSet\Services\BonjourService\Parameters. Verify that you have sufficient access to that key, or contact your support personnel?
See Troubleshooting issues with iTunes for Windows updates for general advice.
For "Could not open key/write value" errors when reinstalling try b noir's user tip:
"Could not open key: UNKNOWN\Components\[LongStringOfLettersAndNumbers]\
[LongStringOfLettersAndNumbers]" error messages when installing iTunes for Windows but apply it to the branch in question.
In this thread the OP found their AV solution appeared to be blocking access to the registry.
tt2 -
iTunes no longer works on my Windows VISTA system. Get error msg saying an application is attempting to access C runtime library incorrectly... Error 7, Windows error 1114. Same msg, or one that says unable to install, when trying to update or reinstall iTunes. iTunes worked well up until about a month ago when this error msg starting appearing.
Go to Control Panel > Add or Remove Programs (Win XP) or Programs and Features (later)
Remove all of these items in the following order:
iTunes
Apple Software Update
Apple Mobile Device Support (if this won't uninstall move on to the next item)
Bonjour
Apple Application Support
Reboot, download iTunes, then reinstall, either using an account with administrative rights, or right-clicking the downloaded installer and selecting Run as Administrator.
The uninstall and reinstall process will preserve your iTunes library and settings, but ideally you would back up the library and your other important personal documents and data on a regular basis. See this user tip for a suggested technique.
Please note:
Some users may need to follow all the steps in whichever of the following support documents applies to their system. These include some additional manual file and folder deletions not mentioned above.
HT1925: Removing and Reinstalling iTunes for Windows XP
HT1923: Removing and reinstalling iTunes for Windows Vista, Windows 7, or Windows 8
tt2 -
Apple support had not responded to my requests for clarification. The update corrupted both ITunes and Office Outlook mobileme. The error message when I tried to start up I Tunes was Error 7 Windows 193. I un installed I Tunes and re installed the latest ver and encountered the same error message. I finally did a system restore. Was this a one time problem or is the update bad. In over 30 years I'd never had a problem with any Apple update.
Hi Lutacrew,
If you are having issues with iTunes after an attempted update, you may find the following article helpful:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Regards,
- Brenden -
Hi!
So i think i closed the wrong service at some point a few weeks back (apple mobile device) but iTunes remained working after that for another week. I then updated iTunes and i get the same "Service ‘Apple Mobile Device’ (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services." every time. If i click ignore, just so i can access iTunes with out syncing my iPod (touch 2nd gen) i then get 'iTunes was not installed correctly. Please re-install iTunes. Error 7 (Windows error 193)" when it has all installed. I don't understand what the problem is anymore as I have looked at other questions on the apple website, carried out the advice and it hasn't work. Any of them.
Tings I have done:
- Wiped all iTunes and Apple data from my computer (if you search for 'iTunes' or 'Apple' nothing comes up apart from applets from system code.
- Attached iPod before iTunes install and updated drivers.
- Installed iTunes as 'Run as administrator'
- Uninstalled and re-installed the software nearly 20 times now and rebooted the computer in between everytime.
Please someone help because i really need to get music on my ipod and i enjoy the ease of use of iTunes compared to spotify or Windows Media Player.For general advice see Troubleshooting issues with iTunes for Windows updates.
The steps in the second box are a guide to removing everything related to iTunes and then rebuilding it which is often a good starting point unless the symptoms indicate a more specific approach. Review the other boxes and the list of support documents further down the page in case one of them applies.
The further information area has direct links to the current and recent builds in case you have problems downloading, need to revert to an older version or want to try the iTunes for Windows (64-bit - for older video cards) release as a workaround for performance issues or compatibility with QuickTime or third party software.
Your library should be unaffected by these steps but there are also links to backup and recovery advice should it be needed.
Regarding AMDS failures there is a hint in another thread that disabling the Windows Firewall before attempting to reinstall may help, otherwise take a look at the steps outlined in this post. Re: Can't install iTunes 12.1 on Windows 7 64-bit. I know they look a little daunting, but the process of generating the logs themselves isn't that hard to do. Extracting useful information from them is still a challenge but maybe something will leap out. If you want to post the log for the failed components for me to have a look at here or in the other thread please edit out any personal information, particularly your email address, first.
tt2 -
Authorization error when exporting business system
Hi ,
I am on XI 7.0 spo9.I am trying to transport from dev to qa .
I am able to easily export (login using xisuper ) Technical system.
However while exporting Business system .when it gives me to download a file I get an authorization error .
Kindly helpHi,
Check XISUPER has the below roles in SU01.
SAP_BC_AI_LANDSCAPE_DB_RFC
SAP_SLD_ADMINISTRATOR
SAP_SLD_CONFIGURATOR
SAP_SLD_DEVELOPER
SAP_SLD_ORGANIZER
SAP_SLD_GUEST
add the above roles for XISUPER and get the green color those roles using Tcode : PFCG.
The above roles should be in green color.
Regards,
Venu. -
I cannot open itunes on my windows 7 system. I get an error message error 7 windows 1114
I cannot open i tunes on my windows 7 system. i get an error message error 7 windows 1114. I cloud opens. quick times works as well. But despite reinstalling several times it doesn't open
Refer to this article:
iTunes for Windows: "Error 7" message when opening iTunes
http://support.apple.com/kb/TS3074
Maybe you are looking for
-
I can't delete the master file, which is located on my external HD, through aperture
I import a folder to aperture which is stored on my external HD, and keep the originals on the HD. If I try to delete a master file with the option, file-delete master image and all versions, the photo deletes from Aperture, but not my hard drive.
-
My ipod nano has been working fine for at least three years. All of a sudden I get two messages. First, "there is a problem with this drive, scan and fix it". And, an Ipod has been detected but can't be identified properly. It's a 6th generation n
-
Google Advanced Search only displays 10 Results per page in Firefox 3.6.10
In Google Advanced Search, choose any value for Results per page greater than 10 and do a search. When using Firefox 3.6.10, only 10 results are displayed on each page of results. 10 results per page is the Google default, and the Results per page se
-
How to recover data if one datafile was lost
if i have a tablespace with 5 datafiles 9i or 10g... it's a fictional scenario :) one was lost during db start up and other 4 was still thre if no backup avail for restore and no archivelog for recreating the datafile how do i recovery data in this t
-
Rendering audio of some clips distorted
I have an older project from last year imported by an older version of iMovie. I imported those clips into FCE and things are looking fine. It had to render the audio and my sequence was complete..., until I spot checked some sections of it. Two of t