Remote server response was not rfc conformant
Hii folks, I have an issue with Exchange 2010 outbound mails.
Mails of some domains stuck in the queue with error "remote server response was not rfc conformant"
Appreciate your responds.
Hi,
According to your description, This issue is related to one of your clients. And I’d like to confirm if emails from the problematic user are stuck in the queue and other emails are delivered successfully.
If yes, I’d like to also confirm the version of the problematic user. Is it Exchange account? External user or internal user? Does it belong to a distribution group?
Additionally, I recommend to check the SMTP protocol log:
Understanding Protocol Logging:
http://technet.microsoft.com/en-us/library/aa997624(v=exchg.141).aspx
Configure Protocol Logging:
http://technet.microsoft.com/en-us/library/bb124531(v=exchg.141).aspx
Thanks,
Angela Shi
TechNet Community Support
Similar Messages
-
try
MailMessage mail = new MailMessage();
SmtpClient SmtpServer = new SmtpClient("smtp.gmail.com");
mail.From = new MailAddress("[email protected]");
mail.To.Add("[email protected]");
mail.Subject = "Test Mail..!!!!";
mail.Body = "mail with attachment";
System.Net.Mail.Attachment attachment;
attachment = new System.Net.Mail.Attachment(@"C:\Attachment.txt");
mail.Attachments.Add(attachment);
SmtpServer.Port = 587;
SmtpServer.UseDefaultCredentials = true;
SmtpServer.Credentials = new System.Net.NetworkCredential("userid", "Password");
SmtpServer.EnableSsl = true;
SmtpServer.Send(mail);
Catch(Exception exception)
When i m run this part of code it throw an Ecxeption
Given Below is the Error..
The SMTP server requires a secure connection or the client was not authenticated. The server response was: 5.5.1 Authentication Required.
Bikky Kumartry
MailMessage mail = new MailMessage();
SmtpClient SmtpServer = new SmtpClient("smtp.gmail.com");
mail.From = new MailAddress("[email protected]");
mail.To.Add("[email protected]");
mail.Subject = "Test Mail..!!!!";
mail.Body = "mail with attachment";
System.Net.Mail.Attachment attachment;
attachment = new System.Net.Mail.Attachment(@"C:\Attachment.txt");
mail.Attachments.Add(attachment);
SmtpServer.Port = 587;
SmtpServer.UseDefaultCredentials = true; ///Set it to false, or remove this line
SmtpServer.Credentials = new System.Net.NetworkCredential("userid", "Password");
SmtpServer.EnableSsl = true;
SmtpServer.Send(mail);
Catch(Exception exception)
Given Below is the Error.. The SMTP server requires a secure connection or the client was not authenticated. The server response was: 5.5.1 Authentication Required.
Solution:
The error might occur due to following cases.
case 1: when the password is wrong
case 2: when you try to login from some App
case 3: when you try to login from the domain other than your time zone/domain/computer (This
is the case in most of scenarios when sending mail from code)
There is a solution for each
solution for case 1: Enter the correct password.
Recomended: solution for case 2: go to
security settings at the following link https://www.google.com/settings/security/lesssecureapps and
enable less secure apps . So that you will be able to login from all apps.
solution 1 for case 3: (This might be helpful) you need to review the activity. but reviewing the activity will not be helpful due to latest security
standards the link will not be useful. So try the below case.
solution 2 for case 3: If you have hosted your code somewhere on production server and if you have access to the production server, than take remote
desktop connection to the production server and try to login once from the browser of the production server. This will add exception for login to google and you will be allowed to login from code.
But what if you don't have access to the production server. try
the solution 3
solution 3 for case 3: You have to enable
login from other timezone / ip for your google account.
to do this follow the link https://g.co/allowaccess and
allow access by clicking the continue button.
And that's it. Here you go. Now you will be able to login from any of the computer and by any means of app to your google account.
Regards,
Nabeel Arif -
Interesting db mail issue. If i click send test mail from sql mgmt studio, it works fine, but when i execute a SP to send a mail, it fails. One thing I noticed is that the "LastModified" column in the mail log shows the domain account when a test
mail was sent from mgmt studio, but show "sa" when the SP was used to send mail.
This is from SQL 2012, did not see this in sql 2008, looks like 2008 always used the service account. any ideas ?
Get this error:
The mail could not be sent to the recipients because of the mail server failure. (Sending Mail using Account 1 (2013-04-30T16:36:52). Exception Message: Cannot send mails to mail server. (Mailbox unavailable. The server response was: 5.7.1 Client does not
Thanks.
RangaHi Ranga,
I also use SQL Server 2012. I send a test email through SQL Server Management and the last modified By “sa”.
If you used stored procedure to send a test email. Please use the command below:
EXEC msdb.dbo.sp_send_dbmail
@profile_name = 'Adventure Works Administrator',
@recipients = '[email protected]',
@body = 'The stored procedure finished successfully.',
@subject = 'Automated Success Message' ;
I can both send test email through SQL Server Management Studio and SP. Make sure you have the right profile. Since you could send test mail via SQL Server Management Studio, please try again to send it via SP.
Thanks.
If you have any feedback on our support, please click
here.
Maggie Luo
TechNet Community Support -
Trying to setup an Exchange 2013 server, with the DC and Exchange on same machine. WHen I try to deliver for either of the 2 mailboxes I have setup, I get this error.
The server returned status code 451 - Error in processing. The server response was: 4.7.0 Temporary server error. Please try again later. PRX3
It doesn't seem to be a resource issue (I'm running an XL instance on Azure), and all other connectivity works fine (and fast). I just can't receive email there.
Looking in the event logs, I saw one issue related to the Front End HTTP proxy, but I wouldn't assume that's relevant here. (And connectivity via Outlook & OWA seem to be fine, with the exception
of some redirect issues on the latter).
I did end up installing Exchange on a secondary drive for space considerations, so the location is different... not sure if that would factor in either.
Any ideas? I don't even really know where to start debugging this. I'm trying to set this up to work on some event sync/forwarding code.Ok, I think I solved my problem but figured I would update here for others who may be running into the same issue.
In my \Exchange\TransportRoles\Logs\FrontEnd\ProtocolLog\SmtpReceive\*.LOG, I found more detailed information on the issue.
"Message or connection acked with status Retry and response
451 4.4.0 Error encountered while communicating with primary target IP address: ""421 4.2.1 Unable to connect.""
Attempted failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts. The last endpoint attempted was 10.10.10.1:2525"
I thought creating an endpoint for 25 would be sufficient, but once I created another endpoint for 2525 then my tests started working. -
Getting error 462 - The remote server machine does not exist or is unavailable
I have several modules that read and write data to and from Excel 2010 worksheets. I am noticing that the Excel process does not end aven though Excel is not running on my PC. It is like an orphan process. If I try running the Access module again I get the
message "error 462 - The remote server machine does not exist or is unavailable". Here is the code I am running. When I click the Debug button on the message box the line "rowNum = objXLAppln.Range("A" & Rows.Count).End(xlUp).Row"
is highlighted.
Option Compare Database
Option Explicit
Function ImportImportanceScores()
Dim RecSet As DAO.Recordset
Dim objXLAppln As Excel.Application
Set objXLAppln = New Excel.Application
Dim objWBook As Excel.Workbook
Dim rowNum As Variant
Dim i As Integer
Dim j As Integer
Dim StrPathFile As String, strFile As String, strPath As String
Dim strBrowseMsg As String, strInitialDirectory As String, strFilter As String
'show dialogue box
strBrowseMsg = "Select the EXCEL file:"
'set directory to load files from
strInitialDirectory = "C:\Bridge_CIP_Part-A_B\"
'run strFilter function
strFilter = ahtAddFilterItem(strFilter, "Excel Files (*.xlsx)", "*.xlsx")
StrPathFile = ahtCommonFileOpenSave(InitialDir:=strInitialDirectory, _
Filter:=strFilter, OpenFile:=True, _
DialogTitle:=strBrowseMsg, _
Flags:=ahtOFN_HIDEREADONLY)
If StrPathFile = "" Then
MsgBox "No file was selected.", vbOK, "No Selection"
Exit Function
End If
'Set Excel application object. Critical for macro to run properly. Do not change.
'Open workbook and worksheet to load data.
With objXLAppln
Set objWBook = objXLAppln.Workbooks.Open(StrPathFile)
objXLAppln.Visible = True
End With
Set RecSet = CurrentDb.OpenRecordset("Importance_Scores")
'Copy data from Excel cells to Access fields
objXLAppln.Sheets("Importance_Scores").Select
rowNum = objXLAppln.Range("A" & Rows.Count).End(xlUp).Row
objXLAppln.Range("A6").Select
'Add records to table from Excel
With RecSet
For i = 0 To rowNum - 6
RecSet.AddNew
RecSet.Fields("CIP_ID").value = objXLAppln.ActiveCell.Offset(i, 0).value
RecSet.Fields("Target_Timeframe_for_Construction").value = objXLAppln.ActiveCell.Offset(i, 2).value
RecSet.Fields("ImportanceFactor_TI-1").value = objXLAppln.ActiveCell.Offset(i, 21).value
RecSet.Fields("ImportanceFactor_TI-2").value = objXLAppln.ActiveCell.Offset(i, 22).value
RecSet.Fields("ImportanceFactor_TI-3").value = objXLAppln.ActiveCell.Offset(i, 23).value
RecSet.Fields("ImportanceFactor_TI-4").value = objXLAppln.ActiveCell.Offset(i, 24).value
RecSet.Fields("ProjectRank").value = objXLAppln.ActiveCell.Offset(i, 33).value
RecSet.Update
Next i
End With
'Close everything
RecSet.Close
objWBook.Close SaveChanges:=False
objXLAppln.Quit
Set RecSet = Nothing
Set objWBook = Nothing
Set objXLAppln = Nothing
End FunctionIn the line
rowNum = objXLAppln.Range("A" & Rows.Count).End(xlUp).Row
Rows does not refer to objXLAppln or to objWBook. Change it to
rowNum = objXLAppln.Range("A" & objWBook.Sheets("Importance_Scores").Rows.Count).End(xlUp).Row
Regards, Hans Vogelaar (http://www.eileenslounge.com) -
Aironet 1600 - A response was not received from the router or access point
Hi,
I'm trying to set up a wireless network with multiple SSID's. The new network only has CISCO products (router, switches). For the moment I'm trying to connect to 1 SSID (Windekind.Gast). the SSID is visible but when connecting devices have te folowing error message in the log:
Connection status summary
Connection started at: 2015-02-17 09:55:49-951
Profile match: Success
Pre-Association: Success
Association: Fail
Security and Authentication: Not started
Root cause:
Wireless association to "Windekind.Gast" failed
A response was not received from the router or access point.
Detailed root cause:
Wireless association to this network failed. Windows did not receive any response from the wireless router or accesspoint.
The signal is perfect (I'm only a few feet away from the AP).
To make sure there is no dhcp problem I tested the swich port in access mode for vlan 30 which supplied an IP correctly. I'm really not seeing the problem and searched the web for days now! Any help would be very much appreciated!
Below the config of the access point (done via de web interface).
! Last configuration change at 05:30:28 UTC Mon Mar 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel 2452
no preamble-short
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
endHi Rasika
thanks for the reply! 10.0.0.81 belongs to vlan 1. I changed the config as suggested but no luck.. (same problems are logged in the event viewer). the ap is connected to a switchport in trunk mode and vlan 1 is the native lan (untagged). the port also is joined to vlan 30 (and others).
Below the new config. Hope you can see an error..
! Last configuration change at 22:56:10 UTC Thu Apr 1 1993
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname AP002-C
logging rate-limit console 9
enable secret 5 $1$Bxv3$Of8o5..8v6gzIiAe2tXlh/
no aaa new-model
no ip cef
dot11 syslog
dot11 vlan-name Default vlan 1
dot11 vlan-name Windekind.Directie vlan 50
dot11 vlan-name Windekind.Gast vlan 30
dot11 vlan-name Windekind.Klasnet vlan 40
dot11 ssid Windekind.Directie
vlan 50
band-select
authentication open
mobility network-id 50
dot11 ssid Windekind.Gast
vlan 30
band-select
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 30
wpa-psk ascii 7 14201B05080121222A2C6A6D63
dot11 ssid Windekind.Klasnet
vlan 40
band-select
mobility network-id 40
crypto pki token default removal timeout 0
username Cisco password 7 112A1016141D
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 2
stbc
beamform ofdm
mbssid
speed basic-1.0 2.0 5.5 11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
no preamble-short
channel 2452
station-role root
payload-encapsulation dot1h
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 30 mode ciphers aes-ccm tkip
ssid Windekind.Directie
ssid Windekind.Gast
ssid Windekind.Klasnet
antenna gain 4
no dfs band block
stbc
beamform ofdm
mbssid
speed basic-6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
channel dfs
station-role root
payload-encapsulation dot1h
interface Dot11Radio1.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 subscriber-loop-control
bridge-group 30 spanning-disabled
bridge-group 30 block-unknown-source
no bridge-group 30 source-learning
no bridge-group 30 unicast-flooding
interface Dot11Radio1.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 subscriber-loop-control
bridge-group 40 spanning-disabled
bridge-group 40 block-unknown-source
no bridge-group 40 source-learning
no bridge-group 40 unicast-flooding
interface Dot11Radio1.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 spanning-disabled
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.30
encapsulation dot1Q 30
no ip route-cache
bridge-group 30
bridge-group 30 spanning-disabled
no bridge-group 30 source-learning
interface GigabitEthernet0.40
encapsulation dot1Q 40
no ip route-cache
bridge-group 40
bridge-group 40 spanning-disabled
no bridge-group 40 source-learning
interface GigabitEthernet0.50
encapsulation dot1Q 50
no ip route-cache
bridge-group 50
bridge-group 50 spanning-disabled
no bridge-group 50 source-learning
interface BVI1
ip address 10.0.0.81 255.255.255.0
no ip route-cache
ip default-gateway 10.0.0.1
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging facility user
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
end
t -
Can't send emails. The server response was: 1060208403.
Nobody in my office can send emails today. All eight of us can access the Internet and send emails normally on our computers.
When attempting to send a message I get the following error message:
Cannot send message using the server mail.ourserver.org
The server response was: 1060208403
We are using Port 26 to send email.
Our web/email host did not find any issue with the mail server or with our account. They suggested it's a problem with our mail client.
Any ideas?It would appear somebody needs to connect into your network and/or your client system(s), and to dig around.
So there are presently eight separate systems have eight separate cases of the same problem, and your email vendor says it is a client issue?
Ok; that would not be my first guess here.
An initial suspicion would involve hardware common to all of the client systems. At your network, wireless, router(s) or switch(es) and/or at your firewall. At the connection with your network and the rest of the Internet.
And a look at the email vendor and the vendor's server(s), since the vendor is also common to all eight clients here.
Has anyone been working with your DNS, firewall or other such? (I'm going to assume not, but it is worth a mention.)
Use of port 26 is odd. I'd expect port 25 or port 587. Can you confirm that port? Port 25 is comparatively unusual for sending email of late; many entities now use 587.
Are you running a local email server? If so, that could be having an issue. I'd expect to see a local SMTP email server connect to the next SMTP server via port 25 or potentially via 587.
Can the clients make connections to other networks and servers; are other web servers and sites accessible? If so, that tends to rule out the common pieces of hardware; hunks such as the firewall and the Internet connection.
There's no obvious translation of that specified error code; that's not an SMTP error, nor is it visible anywhere on the 'net. It may well be something from the client, or something from the network somewhere.
Here is Thunderbird troubleshooting information, which might give you some ideas of where to look here (even though you're probably using Mail.app):
http://kb.mozillazine.org/Cannotsendmail
If you have an email server running locally, the spectrum of potential problems becomes rather larger. -
LR3 error - "a response was not received in time"
I have been using LR for a couple of years now and have uploaded many web galleries to my website. Recently, however, it is just not happening for me.
I have been trying for 3 weeks to upload 3 web galleries in LR3 - they range in size from 200 - 300 pics per gallery.
The error message I get is "a response was not received in time".
I was using the trial version of LR3 before buying but was told they could not help me unless I'd bought the software. VERY helpful and not exactly great PR!! As I was desperate with waiting clients I bought the upgrade anyway. That was a week ago.
I have spent 1.5 hours on the phone to the US LR support and as long with UK support (US was way better).
I have had return calls from LR and a promise to hear back from the engineers as the problem was escalated. That was nearly a week ago and I've not heard a word.
I am using a brand new iMac bought on 22 July and haven't done anything other than try to process and upload these 3 galleries so have huge amounts of memory available.
I have unlimited web space.
I have uninstalled and reinstalled LR twice.
My 8 year old pc can upload the galleries fine (although soooo slowly as it is inadequate for this type of work), so there is no connection problem.
As a work around I exported the galleries to the desktop and uploaded using 5 different FTP programmes. Filezilla seems to work best, but although the gallery uploads, not all the pictures appear properly - normally 10 - 20 pics are a problem. Even though they appear to have uploaded, only the thumbnail shows, not the large image. It is not the pics as if I reload a gallery it will be different pics that fail to show correctly each time - totally random.
I have been able to upload a gallery through LR of between 1 and 5 pics, but no more than 5 (proving the settings are fine), until today.
Today I managed to upload over 400 pics using an html gallery.
Next I tried uploading 50 in a flash gallery and this also worked, so I tried to upload 1 of my 3 complete galleries.
The first attempt resulted in an "unknown error message" - believe it or not I was quite hopeful as at least it was a different error message.
The second attempt resulting in "a file was truncated during upload" Never seen that one before.
The third attempt resulted in my now familiar error message of "a response was not received in time"
Desperate for help please.JaneNeedsHelp7 wrote:
I don't understand why it works fine with a PC - have tested with 3, 2 of which are seriously old - but not with my brand new iMac. I thought that getting whiz bang machine I'd have fewer hassles.
In my experience, it is the wizz bang machines which always seem to have the problems! I must admit to sticking with my desktop (a Windows machine) rather than my Laptop (a MAC) when doing FTP transfers using LR as certainly with LR 2 the FTP in LR on the MAC did seem to have some hiccups. Perhaps using a separate FTP to upload the site is the best solution for the time being although the other problems you report don't seem to directly relate to the FTP. There were some more detailed postings in the past from MAC users on this issue and some about the BIN file problem on windows servers, so a search may help. -
Unable to connect to the analysis server the server name was not found
Hi,
One of the user is trying to run reports from PWA 2010 and gets the below error.
Unable to connect to the analysis server the server name was not found.Please verify the name you entered is correct and then try again.
Errors in the ole db provider.An error occurred while loading the connection dialog boxcomponent for prompting.
Please advice why?Dear Project Help,
Please help the community with more information.
Which kind of reports are you running? Excel using OLAP?
If so, check out on your Excel sheet connection information to see if it's using the SSS Authentication mode:
I'm asking this because if the failure happens with a single user, the authentication method is wrong and you should set up Secure Store Service properly.
Let me know if you need any help on this.
Cheers -
Hello,
I just setup an exchange 2013 server with hosted with the same machine of Active Domain Controller.
I tested the connectivity of the server , i found that the mailbox can only send email to external mailbox however it cant receive any mail neither from external mail nor internal mail.
I ran a test from exchange connectivity analyzer for inbound mail and it failed with the following message.
The server returned status code 451 - Error in processing. The server response was: 4.7.0 Temporary server error. Please try again later. PRX3
I did a search on this forum and found the following thread
social.technet.microsoft.com/Forums/exchange/en-US/288e1619-ce56-4c3a-8bb1-4886835520fe/delivery-fails-the-server-response-was-470-temporary-server-error-please-try-again-later?forum=exchangesvrdeploy
but no luck , i dont know how to set an alternative host, would somebody please help.
error details:
Message: Error in processing. The server response was: 4.7.0 Temporary server error. Please try again later. PRX3
Type: System.Net.Mail.SmtpException
Stack trace:
at System.Net.Mail.DataStopCommand.CheckResponse(SmtpStatusCode statusCode, String serverResponse)
at System.Net.Mail.DataStopCommand.Send(SmtpConnection conn)
at System.Net.Mail.SmtpClient.Send(MailMessage message)
at Microsoft.Exchange.Tools.ExRca.Tests.SmtpMessageTest.PerformTestReally()
The server returned status code 451 - Error in processing. The server response was: 4.7.0 Temporary server error. Please try again later. PRX3
Exception details:
Message: Error in processing. The server response was: 4.7.0 Temporary server error. Please try again later. PRX3
Type: System.Net.Mail.SmtpException
Stack trace:
at System.Net.Mail.DataStopCommand.CheckResponse(SmtpStatusCode statusCode, String serverResponse)
at System.Net.Mail.DataStopCommand.Send(SmtpConnection conn)
at System.Net.Mail.SmtpClient.Send(MailMessage message)
at Microsoft.Exchange.Tools.ExRca.Tests.SmtpMessageTest.PerformTestReally()
Elapsed Time: 3107 ms.
The server returned status code 451 - Error in processing. The server response was: 4.7.0 Temporary server error. Please try again later. PRX3
Exception details:
Message: Error in processing. The server response was: 4.7.0 Temporary server error. Please try again later. PRX3
Type: System.Net.Mail.SmtpException
Stack trace:
at System.Net.Mail.DataStopCommand.CheckResponse(SmtpStatusCode statusCode, String serverResponse)
at System.Net.Mail.DataStopCommand.Send(SmtpConnection conn)
at System.Net.Mail.SmtpClient.Send(MailMessage message)
at Microsoft.Exchange.Tools.ExRca.Tests.SmtpMessageTest.PerformTestReally()
Elapsed Time: 3107 ms.Thanks god, finally i found the solution :) , i can go to sleep
i added my ad domain name to the host table then all the problems are solved!!!
source
http://www.techieshelp.com/exchange-2013-451-4-7-0-temporary-server-error-please-try-again-later-prx5/ -
CCA Error: "the server response could not be parsed [12152]"
Hi,
Has anyone gotten this error message on Cisco Clean Access Agen CCA Agent "the server response could not be parsed [12152]". I have tried everything I can but can't get rid of the error. I am running CCA 4.0.5 in OOB+VG, cluster mode for both CAM & CAS.Syed,
If you are still there, can we pick up from where we left?
http://forums.cisco.com/eforum/servlet/NetProf?page=netprof&forum=Expert%20Archive&topic=Security&CommCmd=MB%3Fcmd%3Dpass_through%26location%3Doutline%40%5E1%40%40.1ddf45d4/8#selected_message -
Mailbox unavailable. The server response was: 5.7.1 Unable to relay
I have tried to send a mail from my ASP.Net web application, But I Receive
"Mailbox unavailable. The server response was: 5.7.1 Unable to relay"
error in my log file, I have made the following change in SMTP Virtual server in IIS 6 Manager in the server
1.Added 127.0.0.1 and IP of server in Smtp Virtual Server->Properties->Access tab->Relay
under only the list below
2.Checked anonymous access in Smtp Virtual Server->Properties->Access tab->authentication
3.Changed IP address to All unassigned and also to IP of server in General tab
But no luck till now. Looking forward for your valuable reply. Thanks in AdvanceHi,
For this issue, i think you should ask in:
http://forums.asp.net/default.aspx/7?General+ASP+NET
Regards.
Vivian Wang -
The server response was: 4.4.1?!?
Hi!
I am having a problem with Mail 1.3.11 in OS X 10.3.9.
I can send and receive e-mails, but when I try to send a e-mail with a attachment [doesn't matter size or kind of file], it doesn't go.
After a while I get this message:
Sending the message content to the server failed.
The server response was: 4.4.1 collect: read timeout on connection from
[my ip xx.xxx.xxx.xx], from=<[email protected]>
You can try to send using a different server. All messages will use this
server until you quit or change your network settings.
My ISP says that in their side everything is ok.
How can I fix this. Can you help me?!?
Thank you,
PauloIs your ISP's SMTP server authenticated for your ISP's email account?
How are you connected to the internet - via an Ethernet connection to a modem or thru a wired or wireless router connected to same?
This sounds like it may be an MTU (Maximum Transmission Unit) problem. The default MTU setting for OS X with an Ethernet connection is 1500 which is the highest available. If your ISP requires a lower MTU setting, this will prevent sending messages with attachments or messages over a certain size. -
"I have one workstation with static IP, Wants to create batch file to log in to this,using user name and password, copy back up files from that workstation to my desktop with batch file, please help
I am currently using batch file for back up for domain servers with robocopy commands in batch file but one of the workstation is not in domain and has static ip , also it has username and password,
Wants to create batch file on my desktop to log in this server---with username and password,, copy files from particular folder and paste it on my desktop in particular folder or auto create that folder,
please help, "
P DaveJRV,
I can understand that, 1stly I am not a scripting guy, I know very very basic of this,
2ndly, I need help , I am not asking anyone here to write code for me, I have already wrote that but its not doing which its suppose to do,
check below screen shot, after running suggested script, it has mapped drive ,
now I do not want to do that, I want just files to copy from that machine to my machine, and want script which I can run from any PC,
Tried with UNC PATH as well, but not making any difference, its keep mapping that server drive to my computer
P Dave
JRV,
I can understand that, 1stly I am not a scripting guy, I know very very basic of this,
2ndly, I need help , I am not asking anyone here to write code for me, I have already wrote that but its not doing which its suppose to do,
check below screen shot, after running suggested script, it has mapped drive ,
now I do not want to do that, I want just files to copy from that machine to my machine, and want script which I can run from any PC,
Tried with UNC PATH as well, but not making any difference, its keep mapping that server drive to my computer
P Dave
Bill - he still sees that "connection" although it isn't mapped it is attached temporarily.
P - Log off and log back on and the attached connection will be gone. It is temporary. Again - knowing the basics of WIndows would let you know this.
We have given you all of the answers that are possible. There is no other way unless you have installed things like PowerShell and PowerShell remoting or an FTP server.
If you do use a drive it can be just as easily deleted after you have finished the copy.
Again: "NET USE /?" will tell you all of the options.
Saying you know nothing is not an excuse for not thinking or looking more deeply into the suggestions made by those trying to help you. This is not a MIcrosoft support forum or help desk. It is a forum for admiinistrative scripting and assumes
that those coming here are technically trained or experienced in the basics of Windows technology.
¯\_(ツ)_/¯ -
This is starting to REALLY frustrate me! I used to be able to send emails with attachments perfectly fine with my email, and now all of a sudden it won't work. I work from home, and 8/10 my emails need to have images in them. SOMEONE PLEASE HELP ME!
Contact your internet service provider. They can run some tests to verify the cause of the problem. This sounds very much like an ISP issue.
Maybe you are looking for
-
"waiting for modem to become available"
I am utilizing Airport Express to fax from Brother MFC-490CW and MacBook Pro and receiving error message "waiting for modem to become available". Many tasks state completed but then upon looking into it, they haven't sent for the same reason. I hav
-
Hi, I have a number of slideshows in my iphoto that I use on a regular basis and like very much. As christmas is coming up thought it would be a good idea to create a DVD of a few family slideshows from the year to send out. However, ALL THE PHOTOS O
-
FNDLOAD giving error while downloading
Dear, We are using below mentioned command through applmgr user by switching off 'FND_TOP' and executed this but getting error as mentioned. FNDLOAD apps/apps 0 Y DOWNLOAD $FND_TOP/patch/115/import/afffload.lct HR_Position_Functions.ldt VALUE_SET FLE
-
Oracle 11i - Concurrent Request Set Details
Hi, I would like to frame a query that extracts the concurrent request sets and the associated child requests. I am not sure of the data mapping.Can somebody help me with the query. Regards, Radhika.
-
Hallo Zusammen! Ich habe folgendes Problem: Ich habe verschieden Beta SP per Datavideo DAC 2 Converter als DV in Premiere 1.5 Pro gecaptured und als Rolle zusammengestellt. Nun würde ich gerne die vollständige Sequenz direkt aus Premiere auf eine Vid