RV042 - loosing connection

Hi there.
My problem is as follows
Setting the device up with static WAN is no problem, I get internet access and everything works perfect - using WAN1.
But when connecting a LAN port to a switch with a dmz lan, the WAN port looses connection
The LAN address of the RV042 VPN Router is set to: 10.10.20.5 with subnet 255.255.255.248
Other equipment is connected to the switch with 10.10.20.6, 10.10.20.4 and 10.10.20.2 with same subnet.
10.10.20.2 is a routing device that connects to 172.16.10.2 and further to 10.10.10.2 (LAN) with servers
The device working mode is currently set as Router. Setting it as gateway makes no difference to the problem.
Can you clarify what goes wrong?
Regards

Hi Taras,
As I understand you have Dual WAN and Load balancing , my question do you setup a protocol binding to bind the Voice traffic to go through only one WAN
with protocol binding you can dedicate WAN1 for example for voice Traffic
Protocol binding is working from LAN to WAN under protocol binding setting you have to choose the source IP range , you can have Range of IP for the phone
Destination 0.0.0.0 - 0.0.0.0 and select WAN 1 for example and enable it and save the configuration
Please let me know after your testing
thanks
Mehdi

Similar Messages

Rv042 loose connection

Hello,
i have Cisco rv042.
Firmware Version: v4.2.3.03
configured dual wan and load balance.
i`ve problem with Patton sn4639 BRI So VOIP Router, that every minute loose connection, and need te register again.... when it connected directly to modem everything work`s fine.
Any ideas how to fix it?
thank you

Hi Taras,
As I understand you have Dual WAN and Load balancing , my question do you setup a protocol binding to bind the Voice traffic to go through only one WAN
with protocol binding you can dedicate WAN1 for example for voice Traffic
Protocol binding is working from LAN to WAN under protocol binding setting you have to choose the source IP range , you can have Range of IP for the phone
Destination 0.0.0.0 - 0.0.0.0 and select WAN 1 for example and enable it and save the configuration
Please let me know after your testing
thanks
Mehdi

I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows 8?

I have just upgraded to Windows 8 and my scyning and upgrading my phone with new apple software fails, Itunes looses connection with the device (phone), cant backup the phone or download new software, is this an issues with Windows

Hi, stig2013.
I would recommend the steps in the article below. See the section labeled Verify that the Apple Mobile Device USB Driver is installed > For Windows Vista, Windows 7, and Windows 8 > Update the Apple Mobile Device Driver.
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
If you are receiving an error message, find the exact error number that you recieved in the article below and process the steps.
iTunes: Specific update-and-restore error messages and advanced troubleshooting
http://support.apple.com/kb/TS3694
This error occurs when the device unexpectedly loses its USB connection with iTunes. This can occur if you manually disconnect the device during the restore process. You can resolve this issue by using USB troubleshooting, using a different Dock Connector or Lightning Connector to USB cable, trying another USB port, restoring on another computer, or by eliminating conflicts from third-party security software.
Cheers,
Jason H.

Firewire device looses connection when external screen is inserted into the thunderbolt port? HELP

HI
I am a recording studio engineer. Ive got a Firewire AD/DA Converter (Focusrite Saffire Pro 56) running from my Firewire port of my MacBook Pro, which is running OSX Mavericks. I've also got an external Screen I want to use as an extended display. I'm using a HDMI cable from the screen to a HDMI to Thunderbolt Converter which I then plug into my Thurderbolt Port.
As soon as I plug the screen in, the Firewire Port looses connection completely and I cant use or even choose the Saffire Pro 56 as audio driver. Another thing happens where the Thunderbolt port replaces the Saffire Pro 56 Driver with the screen as the audio output source.
Please help, there's nothing I can find to fix this.
Thanks Maurice

You don't mention which model you have, but this is from the M-Audio Firewire 410 Manual Troubleshooting section:
The FireWire 410 has been designed to give you high performance and professional quality audio. It has been tested under a wide range
of systems and operating conditions. In the real world, however, there is a nearly infinite number of possible operating scenarios, any of
which could affect your system’s performance. Much like owning an automobile, “your mileage may vary.” This section can not begin to
cover all possible issues you may encounter, however we want to give you some suggestions on common problems you may experience.
One thing to avoid is connecting too many devices. The FireWire bus is a dependable, high-speed, high-bandwidth protocol which is ideally
suited for digital audio. Nonetheless, it’s important to remember that audio and multimedia streaming places considerable demands on
your processor and the FireWire bus. Although it is theoretically possible to chain many multiple FireWire devices in series, doing so may
potentially degrade your audio performance.
I guess this degradation could also affect the Firewire HD. Maybe there is a simple fix, but it sounds like the M-Audio people have been down this road before.

Wi-Fi loosing connection every few seconds on my macbook pro and its not my router's fault (running yoseomite)

Basically I bought my new Macbook Pro retina display in September 2014. My wifi was working perfectly well for about a month or two until Yosemite was brought out. I'm not sure if it was immediately after I downloaded Yosemite or not, but not long afterwards I noticed I was having trouble with my wifi (and not just mine but my schools as well). Every time my computer tries to join the wifi network it will work for a while (5 seconds) and it will say that I have a wifi connection but then it will just stop working and it will say I'm not connected to wifi. A few seconds later and it will then reconnect and say I have wifi. I am fairly certain this is not my wireless router ( a BT home hub) as I have other devices such as my iPhone and a computer which does not suffer these problems. After a while of it loosing connection and then gaining connection it will finally stop and the wifi icon at the top will suggest I have a wifi connection but when I hover over it, I see it says "Wi-Fi:looking for networks..." and then 2 seconds later it will say "Wi-Fi: On" and it will repeat like this for however long I am on the network. When the icon appears to suggest I have a connection I am able to load a webpage but it is slow and watching Netflix can be tiresome. I've scoured these forums for information that will solve my issue however all I have found is outdated information from 2010 or 2012 or too technical information that I can't understand. Does anyone else have this problem, has anyone else found a solution, it would be much appreciated if any one could help me solve t.

Please test after taking each of the following steps that you haven't already tried. Stop when the problem is resolved. Back up all data before making any changes.
Step 1
Take the applicable steps in this support article. The Wireless Diagnostics program generates a large file of information about your system, which would be used by Apple Engineering in case of a support incident. Don't post the contents here.
Be sure to test on more than one Wi-Fi network, if at all possible. A desktop computer can be tested with a mobile hotspot, such as the hotspot created by a cell phone. If the problem only exists on one network, then the access point of that network should be the focus of your attention, not the computer.
Step 2
Disconnect all USB 3 devices. If you don't know which are USB 3, disconnect all USB devices except keyboard and mouse.
Step 3
If you're not using a wireless keyboard or trackpad, disable Bluetooth by selecting Turn Bluetooth Off from the menu with the Bluetooth icon. If you don't have that menu, open the Bluetooth preference pane in System Preferences and check the box marked Show Bluetooth in menu bar. Test. If you find that Wi-Fi works better with Bluetooth disabled, you should use the 5 GHz Wi-Fi band. Your router may not support it; in that case, you need a new router.
Step 4
Open the Energy Saver pane in System Preferences and unlock the settings, if necessary. Select the Power Adapter tab, if there is one. Uncheck the box marked
Wake for Wi-Fi network access
if it's checked.
Step 5
Open the Network pane in System Preferences and make a note of your settings in the Wi-Fi service. It may be helpful to take screenshots of the various tabs in the preference pane. If the preference pane is locked, unlock it by clicking the padlock icon and entering your administrator password. Delete Wi-Fi from the service list on the left by selecting it and clicking the minus-sign button at the bottom. Then recreate the service by clicking the plus-sign button and following the prompts.
Step 6
In the Wi-Fi settings, select
Advanced... ▹ TCP/IP ▹ Configure IPv6: Link-local
Click OK and then Apply.
Step 7
Reset the System Management Controller.
Step 8
Reset the PRAM.
Step 9
Launch the Keychain Access application. Search for and delete all AirPort network password items that refer to the network. Make a note of the password first. Turn Wi-Fi off and then back on. You'll be prompted for the password when you reconnect. Save it in the keychain.
Step 10
Make a "Genius" appointment at an Apple Store, or go to another authorized service center.

Loose connection between Mac Mini and Apple TV 2

Help! I have a new Mac Mini 2.5 ghz running Lion and Apple TV2 hooked up to my 32 inch LG TV.
Before I got the Mac Mini, Apple TV was running just fine on the same network with my Win 7 machine.
Ever since I got the Mac Mini and I run the Apple Tv at the same time. I loose connection on both. My cable provider replaced the router and all my other Win 7 machines run just fine on a wireless network. I might also add that when the apple tv and mac mini goes down, my ipad 2 goes down too. Of course, air play doesn't work . It comes and goes.
I have a 2nd Apple TV 2 and hooked that up to the same tv with the same results. I have called Apple many times. They are helpful but not been able to solve my problem. The cable provider and I have traced down to a conflict between the Apple TV, Mac Mini and the IPAD 2 .
Does anyone have any ideas what may be wrong?

I have had multiple ATV's, desktops, laptops, and i Devices all running at the same time without a problem. Typically on a network when you start 2 devices and the connection crashes it is an IP problem. Check the IP address on both devices and see. It is usually easiest to have the router assign IPs automatically using DHCP. The router, computers, and ATVs should also be set to DHCP.
If everything is set to DHCP try disabling DHCP and assign fixed IPs to each device.

Help. Changing subnet mask looses connectivity.

HI,
I know this is basic but is giving me a lot of head ache.
I had a /30 between the Router(3925) and the ASA(5515).
Installed EHWIC on the router to support ASA failover.
I loose connection when I change the mask at /29.
So currently the vlan interface at the router has address 10.xx.xx.xx/30 and ASA interface has 10.xx.xx.xx/29.
This works fine but the moment I change router's mask to /29 it looses connection.
Cant figure out why and I have checked all I could.
- Did shut/ no shut on the interface
- Speed/Duplex settings are set to auto both sides.
Its frustrating. Please help.

Chris,
Pasting below relevant config of both the router and the ASA.
Router
interface Vlan10
description Router_FW1_FW2
ip address 10.xx.xx.2 255.255.255.252
ip access-group 120 in
ip nat inside
ip virtual-reassembly in
interface GigabitEthernet0/0/0
description ASA_Primary
switchport access vlan 10
no ip address
access-list 120 permit ip any any
ASA Config
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 10.xx.xx.1 255.255.255.248
route outside 0.0.0.0 0.0.0.0 10.xx.xx.2 1

MacBook MB466LL/A has loose connection Any suggestions?

MacBook MB466LL/A has loose connection in screen producing line down the middle, if I mess with it (or even wedge something between hinge by the power button) it goes away. Repair center wants to replace whole thing which I can not afford. Any suggestions?

Have you used Software Update to update to 10.7.1. That update was suppose to fix some WiFi Issues. http://support.apple.com/kb/HT4764

IMAC looses connection to Printer

Computer will not print and seems to lose connection to the printer. I deleted all printers and made a new printer connection. Printer has address 192.168.0.14. Later IMAC looses connection to printer again. I look at address on printer and it is now 192.168.0.15. Its done this several times. So why does the printer keep changing its address? Is there a way to set it permanently?

Hi I may have found what you are looking for to set the printer up with a dedicated IP Address. The printer obtains the IP address from your router, I'm not sure why your router is reassigning the IP addresses so frequently.  All of the steps for troubleshooting the Printer Does Not Maintain Wireless Connection are on available on that document, but I have copied the basics on setting up the Static IP address. (Solution five: Assign the printer a static IP address) You can review that document and try the other solutions if you continue to have connectivity issues. Locate your printer's current IP address, which you already haveOpen an Internet browser (Safari, Chrome, Firefox, etc.) on your computer.Type your printer's IP address in the browser's address bar, and then press Enter. The Embedded Web Server (EWS) opens.Click the Network tab from the EWS navigation menu.In the Wireless section, click the Network Address (IP) or IPv6 configuration, depending on your network setup.Click Manual IP, and then click Suggest a Manual IP Address.
A manual IP address, Subnet Mask, and Default Gateway displays.Don't forget to save or apply the settings I believe you might want to try to refresh your network connection afterwards. Power cycling your router allows it to reestablish a fresh connection to all of your devices. Here's how to power cycle your network if you are unsure: 1) Unplug the power cable from your wireless router (NOTE: Do not reset the router)
2) Do the same for the printer
3) Shut down the computer
4) First plug the router back in, and wait for it to fully power up
5) Then plug the printer back in and wait for the wireless light to become solid.
6) Once both the router and printer are on, go ahead and turn the computer back on  Check to make sure the manual IP address has stayed on the printer.
You may also have to remove and add your printer in Printers and Scanners.Open your System Preferences, click on Printers and Scanners.Click the name of your printer, click the minus sign (), and then delete the printer.Once the printer is removed, click the plus sign (), click Add Printer or Scanner, click the name of your printer  Please let me know if these steps resolved your issue, or if there is anything else I can do to help.  I look forward to hearing from you!   Thanks,

Loosing connection to my iMac drive

Hello Support Community,
I have an late 2012 late model iMac and a 13in Retina pro MacBook Pro.
I do a lot of graphics work and what I used to do (before upgrading my MacBook) is do most of my graphics work on my iMac, but sometimes want to sit on the couch and use my MacBook instead.
So i'd log into my iMac's drive on my MacBook and just access the files (so all the files stay on my iMac).
In the last 3 months I have run into a problem where while connect to my iMac's drive, the drive would drop out (loose connection, as you can see by my pings below), which would then make my MacBook not happy and the finder would have the spinning wheel of death for a long time, UNLESS I get up and "wake up" my iMac or force quite the finder on the MacBook.
I have set the Hard drives NOT to sleep on the iMac and made sure that wake for network activity is on, but in the past I could be connected for hours with no problem.
Can anyone shed any light on this?
Also, as I am transferring files from iMac to MacBook sometimes it even drops out half way.
Here is a copy of the pings below where I am pinging from MacBook to iMac..
64 bytes from 10.0.1.5: icmp_seq=181 ttl=64 time=167.427 ms
64 bytes from 10.0.1.5: icmp_seq=182 ttl=64 time=189.954 ms
64 bytes from 10.0.1.5: icmp_seq=183 ttl=64 time=110.766 ms
64 bytes from 10.0.1.5: icmp_seq=184 ttl=64 time=134.041 ms
Request timeout for icmp_seq 185
Request timeout for icmp_seq 186
Request timeout for icmp_seq 187
Request timeout for icmp_seq 188
Request timeout for icmp_seq 189
Request timeout for icmp_seq 190
Request timeout for icmp_seq 191
36 bytes from 10.0.1.1: Redirect Host(New addr: 10.0.1.5)
Vr HL TOS Len   ID Flg off TTL Pro cks      Src      Dst
4 5 00 0054 57b0   0 0000 40 01 0cf3 10.0.1.2 10.0.1.5
Request timeout for icmp_seq 192
36 bytes from 10.0.1.1: Redirect Host(New addr: 10.0.1.5)
Vr HL TOS Len   ID Flg off TTL Pro cks      Src      Dst
4 5 00 0054 c6b3   0 0000 40 01 9def 10.0.1.2 10.0.1.5
Thanks Guys and Gals

Your screenshot is blank and even clicking on it just brings up an error.. the site is having issues.. has done so since the latest Apple update.
Same with your Yosemite installed OS. It is bug farm. There are lots of issues and it is hard to get things working in a consistent way on the network.
Redo the setup of the TC.. starting with a factory reset.
Use only short names, no spaces and pure alphanumeric. eg TCgen5 for basestation name and TCwifi for wireless name.
Use pure alphanumeric passwords.. 8-20 characters mixed case and numbers.
Then if you have issues.. try manually mounting the TC.
In finder. Use Go, Connect to Server from the top menu.
Type in AFP://TCgen5.local (use the actual name of the TC and local is the default domain).
If that doesn't work use the IP address. AFP://10.0.1.1 (that is the default IP in router mode.. you will need a fixed IP for this to be useful).
Save the password in your keychain.
Welcome to the bleeding edge. The problem with every new OS release now is the users are all now beta testers.. !

Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen. Full Wifi signal on both devices

Got new ATV and all set up. It keeps loosing connection with iTunes on laptop and have tried everything suggested in set up guide. It works fine for a while then the iTunes account vanishes from 'computer' menu TV screen. Full Wifi signal on both devices so can't think what could be causing it to happen. Any suggestions please?

Sorry, I updated another thread I was a part of but didn't update my own thread.....ughhh!
I updated all of my ATV 2's and 3's to the latest firmware when it was released and have been problem free since. I do believe the major issue of not being able to connect after a period of inactivity has been corrected with the latest ATV firmware.
I can look at my network connection table using "netstat -an" in a CMD window and I do not see the massive number of connections I saw before the update.
Here is a link to the other thread I was referring to above:
https://discussions.apple.com/message/19952545#19952545
Have you applied the latest firmware updates to your ATV 3's?

Keyboard looses connection says batteries low but just replace

Hi new iMac 21inch with wireless keyboard. Just started to loose connection wireless trackpad working fine. Comes up with low battery warning even though batteries replaced. Then cycles through connection and disconnection constantly. Happened after 10.6.8 upgrade.

Hello Nick:
I seriously doubt that the update to OS X 10.6.8 is the cause of the problem.
Try resetting the PRAM and SMC.
If that does not help, I would return the KB for a warranty replacement.
Barry

Issues with client looses connection with 6.0.196.0

Hi,
We recently upgraded our Wisms to version 6.0.196.0 and after the upgrade we have seen the clients sometimes looses connectivity and has problems to connect. We use an network with 802.1x and PeapMschapv2 with dynamic WEP.
We have disabled aggresive load-balancing but still see the issues.
Any ideas anyone?
Regards,
Martin

Hi,
Any news for these problems? Did the version 7.x fix these CAPWAP UP/DOWN problems with HREAP APs? It seems that I'm having these same problems now. Local APs seems to be fine, but HREAP APs goes UP/DOWN with versions 6.0.196.0 and 6.0.199.4.
There are three 4404 WLCs, where are different sites' office and warehouse APs connected to. The environment is configured as N + N + 1
like following:
WLC1 is for officeAPs. APs are 1131 and they're configured as H-REAP
WLC2 is for warehouseAPs. APs are 1242 and they're configured as Local
WLC3 is for backup and I used this for testing.
After I updated all the WLCs at summer to version 6.0.196.0, there have been issues where the clients looses randomly WLAN-connections. But the complaints just came from the two largest offices. And these didn't happend immeaditly after the update, but after few months. It can be that the summer holidays was reason for it. After some investigations, I updated the WLC3 for version 6.0.199.4, which just got released at the time, and moved these two largest offices' APs to there. Complaints stopped but after a month the second largest office informed that the clients' disconnections started to raise again and the WLAN-network has become unstable again. First there was just couple of issues but it have been raised as the time goes by.
When I made some more investigation to this site, I noticed that the APs' CAPWAP goes DOWN and UP randomly for a second:
*Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN
*Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Nov 12 07:39:29.590: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Nov 12 07:39:29.759: %CAPWAP-5-CHANGED: CAPWAP changed state to UP
*Nov 12 07:39:29.811: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Nov 12 07:39:29.812: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Nov 12 07:39:29.849: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Nov 12 07:39:29.850: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Nov 12 07:39:29.889: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
Then I investigated some more and noticed that this happens on all of the H-REAP APs and almost in the same time:
*Nov 12 07:39:29.537: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's AP (6.0.199.4)
*Nov 12 07:40:17.439: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, second largest site's other AP (6.0.199.4)
*Nov 12 07:41:20.297: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC3, largest site's AP (6.0.199.4)
*Nov 12 07:42:31.928: %CAPWAP-5-CHANGED: CAPWAP changed state to DOWN - WLC1, random site's AP (6.0.196.0)
When I checked the warehouseAPs, which are configured as local in the WLC2 (6.0.196.0), there was nothing like this in the logs. Logs are clean.
But when H-REAP is configured for these APs, the clients should not be disconnected when the CAPWAP goes down? And this whole "process" seems to last just for a second. Not sure if this is the real reason for these client disconnections, but at least this is not normal. I haven't heard complaints from smaller sites, even when APs at them also does the same.
I don't feel great to update the WLCs for the version 7.x, because it just seems to be new feature release, but if it fixes these, then I should think about it. Has someone, who had these same problems, got this fixed with version 7? Or has TAC provide some other patches for this?
Thanks,
Joni

I have a new lion server and 4 lion laptops. The laptops loose connection to the shared documents and printers from the server after roughly 1 hour. By disconnecting and re-connecting wireless the connection is regained to shares and printers

I have a new lion server and 4 lion laptops. The laptops loose connection to the shared documents and printers from the server after roughly 1 hour. By disconnecting and re-connecting wireless the connection is regained to shares and printers. We can still surf the web when it goes down.

Ok 1st one. The warning restriction message relates to this line in main.cf:
smtpd_helo_restrictions = permit_sasl_authenticated permit_mynetworks check_helo_access hash:/etc/postfix/helo_access reject_non_fqdn_hostname reject_invalid_hostname permit reject_invalid_helo_hostname
The last reject occurs after the single word "permit" and is ignored.
However, that's not the problem.
I'm not exactly sure what's happening, but this might be a clue.
It would appear that either postfix is not being able to create the socket for private/policy or it's somehow created with the wrong permissions. You might need to ramp up the debug level to get a better idea.
You could check if it's being created by "netstat -a | grep private/policy" in terminal.
My guess is that it's not being created because there is no setup statement in your master.cf file, but I don't understand why postfix would be looking for it if it isn't set up. Private/policy I think relates to grey listing. Maybe gives you a hint.

Wifi Guests need to reauthenticate when loosing connection

We have Wifi deployment with ISE 1.1.4 authenticating our guest users through CWA.
Whenever a client looses connection for a short time they need to reautenticate by putting in their username and password again.
This is very annoying. Is ther a solution/best practice for this problem?

Rather than setting the session timeout globally, you can set it via RADIUS in the AuthZ policy. We use this to stop Guest users from having to re-auth everytime they disconnect fro the wireless, works well

RV042 - loosing connection

Similar Messages

Maybe you are looking for