Sample Configuration vor PRI (E1) and MICA Modem

Where can I find a Sample Configuration
for a Cisco 3640 with PRI (E1) and a
MICA Modem Card. (Has to work with Dialer Interface)
(I just found a Configuration for PRI (T1) and MICA Modem)

The configuratioj for a T1 or E1 is almost the same, except for E1 parameters:
controller E1 0
framing crc4
linecode hdb3
clock source line primary
pri-group timeslots 1-31
controller E1 1
framing crc4
linecode hdb3
clock source line secondary
pri-group timeslots 1-31
interface serial0:15
isdn incoming-voice modem
dialer rotary-group 1
interface serial1:15
isdn incoming-voice modem
dialer rotary-group 1
interface loopback0
ip address 172.16.254.254 255.255.255.0
interface ethernet0
ip address 172.16.1.1 255.255.255.0
!The following block of commands configures DDR for all the ISDN PRI interfaces
!configured above. The dialer-group and dialer rotary-group commands tie the
!interface configuration blocks to the DDR configuration.
interface dialer1
ip unnumbered loopback0
encapsulation ppp
peer default ip address pool default
ip local pool default 172.16.254.1 172.16.254.60
dialer in-band
dialer-group 1
dialer idle-timeout 3600
ppp multilink
ppp authentication chap pap default

Similar Messages

Disable load balancing on dual PRIs - 3640 with MICA modems for dial out

We have a custom application that connects through reverse telnet to a Cisco 3640 that has 2 NM-24DM modules and 2 PRIs connected to it. Currently all outgoing calls are getting load balanced over the two PRIs. I need to change that so that all calls go over the first PRI and when all channels are used up, it starts using the second PRI. Seems like a simple enough thing to do but I can't figure out how to.
Here is my config
Current configuration : 1401 bytes
version 12.4
service timestamps debug uptime
service timestamps log uptime
service password-encryption
hostname DIALOUT01
boot-start-marker
boot-end-marker
enable secret 5 xxxxxxx
no aaa new-model
clock timezone EST -5
clock summer-time EDT recurring
no ip routing
no ip cef
no ip domain lookup
ip domain name xxxxxxx.xxx
isdn switch-type primary-ni
controller T1 0/0
framing esf
linecode b8zs
pri-group timeslots 1-24
description xxxx
controller T1 0/1
framing esf
linecode b8zs
pri-group timeslots 1-24
description xxxx
interface FastEthernet0/0
ip address dhcp hostname dialout01
no ip route-cache
no ip mroute-cache
duplex auto
speed auto
interface Serial0/0:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
no fair-queue
no cdp enable
interface Serial0/1:23
no ip address
encapsulation hdlc
isdn switch-type primary-ni
no fair-queue
no cdp enable
no ip http server
control-plane
line con 0
line 33 56
modem InOut
modem autoconfigure type mica
transport preferred telnet
transport input telnet
transport output telnet
line 65 88
modem InOut
modem autoconfigure type mica
transport preferred telnet
transport input telnet
transport output telnet
line aux 0
line vty 0 4
password 7 xxxxx login
end
Thanks,
Shahid

If I understand the question I think that isdn bchan-number-order is the command you are interested in. I think it detaults to round-robin, sounds like you want ascending (that is isdn bchan-number-order ascending). It is an interface subcommand.
See http://www.cisco.com/en/US/docs/ios/12_3t/12_3t2/feature/guide/gt_ibcac.html#wp1055853
That may only apply to native ISDN calls and not MICA based calls, but see if that helps.

How to configure 3500 and 6288 and internet modem

I'm new here and would like to have a step by step guide to configure my nokia 3500 and 6288 and my internet modem. Thanks

If you are on linux platform, on command prompt execute netmgr and configure listener fromt there. Or go to $oracle_home/network/admin/listner.ora write the following
SID_LIST_LISTENER =
(SID_LIST =
(SID_DESC =
(SID_NAME = PLSExtProc)
(ORACLE_HOME = /u01/app/oracle/product/10.2.0/db_1)
(PROGRAM = extproc)
LISTENER =
(DESCRIPTION_LIST =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = IPC)(KEY = EXTPROC1))
(ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
For tnsnames.ora write the following
ORCL =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = localhost)(PORT = 1521))
(CONNECT_DATA =
(SERVER = DEDICATED)
(SERVICE_NAME = orcl)
)

Does Apple make/sell the new "Apple In-Ear Headphones with Remote and Mic" with a one sided configuration? So that a person that is deaf in one can hear both sides of a stereo recording? Also, since the "other" bud is not necessary/useful...it's removed.

Does Apple make/sell the new "Apple In-Ear Headphones with Remote and Mic" with a one sided configuration? So that a person that is deaf in one can hear both sides of a stereo recording? Also, since the "other" bud is not necessary/useful...it's removed.

As far as I know, Apple sells no such configuration. However, under Settings > General > Accessability, there is an option to play back audio in monoural mode, which would then play both halves of a stereo mix in each earbud.
Hope that helps.

How to configure isdn pri on gigabit interface on AS 5850 router

hello All,
i currently have a project at hand which is a voip project using sip protocol. my client wants to send voip traffic to my router using STM interface with SIP protocol. But the challenge is how do i convert the sip protocol to ISDN PRI on another STM gigabit interface before sending it to my PSTN switch for onward termination to the customer. currently i use serial interface to communicate with my PSTN using E1 for other existing clients in other to terminate calls to customers. please see sample configuration below:
interface Serial10/1:15
no ip address
encapsulation hdlc
no snmp trap link-status
trunk-group JKN
isdn switch-type primary-net5
isdn incoming-voice modem 64
isdn map address .* plan unknown type unknown
isdn send-alerting
no cdp enable
thank you.
Adekunle

hello n-kirillov,
Yes i mean STM as Synchronous Transport Module for Optical Network. currently, the medium of transport for communication between my router and the PSTN switch is the serial interface whose configuration i have shown above. also currently E1 pri cables are connected to this serial interface and E1s are provision for this serial interfaces directly from the switch for communication with the PSTN switch.
the question now is that my switching team now wants be to communicate with their switch using fibre from STM interface on my router without using PRI cables. is this achievable? if yes what is the configuration like?

PPP Dialup cnx fails - Mica modem never completes state transitions

I have a NAS (LAC) serving PPP calls over PSTN for multiple customers and for this particular connection, the call always drops at the 'State Transition to Ranging". I have another CE router succesfully calling the NAS and usingeaxctly the same external modem, so it proves the NAS works correctly.
What's the 'Ranging state'? What happens here? What causes the Mica modem to go into that state?   Any help to solve this problem will be very much appreciated.
NAS Details:
Cisco Internetwork Operating System Software
IOS (tm) 5300 Software (C5300-J-M), Version 12.3(22), RELEASE SOFTWARE (fc2)
cisco AS5300 (R4K) processor (revision A.32) with 65536K/16384K bytes of memory.
NAS Debugging output:
Mar 1 17:05:22 UTC: VDEV_ALLOCATE: 1/33 is allocated
Mar 1 17:05:22 UTC: EVENT_FROM_ISDN: dchan_idb=0x623BA450, call_id=0x2E41, ces=0x1
   bchan=0xD, event=0x1, cause=0x0
Mar 1 17:05:22 UTC: dev in call to isdn : set dnis_collected & fap_notify
Mar 1 17:05:22 UTC: EVENT_FROM_ISDN:(2E41): DEV_INCALL at slot 1, port 33
Mar 1 17:05:22 UTC: EVENT_FROM_ISDN: decode:calling oct3 0x21, called oct3 0xA1, oct3a 0x83,mask 0x3F
Mar 1 17:05:22 UTC: EVENT_FROM_ISDN: csm_call_info:calling oct3 0x21, called oct3 0xA1, oct3a 0x83,mask 0x3F
Mar 1 17:05:22 UTC: CSM_PROC_IDLE: CSM_EVENT_ISDN_CALL at slot 1, port 33
Mar 1 17:05:22 UTC: Mica Modem(1/33): Configure(0x1 = 0x0)
Mar 1 17:05:22 UTC: Mica Modem(1/33): Configure(0x23 = 0x0)
Mar 1 17:05:22 UTC: Mica Modem(1/33): Call Setup
Mar 1 17:05:22 UTC: csm_connect_pri_vdev: TS allocated at bp_stream 1, bp_Ch 3, vdev_common 0x61D53E9C 1/33
Mar 1 17:05:23 UTC: Mica Modem(1/33): State Transition to Call Setup
Mar 1 17:05:23 UTC: Mica Modem(1/33): Went offhook
Mar 1 17:05:23 UTC: CSM_PROC_IC2_RING: CSM_EVENT_MODEM_OFFHOOK at slot 1, port 33
Mar 1 17:05:23 UTC: EVENT_FROM_ISDN: dchan_idb=0x623BA450, call_id=0x2E41, ces=0x1
   bchan=0xD, event=0x4, cause=0x0
Mar 1 17:05:23 UTC: EVENT_FROM_ISDN:(2E41): DEV_CONNECTED at slot 1, port 33
Mar 1 17:05:23 UTC: CSM_PROC_IC6_WAIT_FOR_CONNECT: CSM_EVENT_ISDN_CONNECTED at slot 1, port 33
Mar 1 17:05:23 UTC: Mica Modem(1/33): Link Initiate
Mar 1 17:05:23 UTC: %ISDN-6-CONNECT: Interface Serial0:13 is now connected to 02155915479 N/A
Mar 1 17:05:24 UTC: Mica Modem(1/33): State Transition to Connect
Mar 1 17:05:24 UTC: Mica Modem(1/33): State Transition to V8bis Exchange
Mar 1 17:05:28 UTC: Mica Modem(1/33): State Transition to Link
Mar 1 17:05:32 UTC: Mica Modem(1/33): State Transition to Ranging <- !!!!!! Call drops here *******
Mar 1 17:05:59 UTC: %ISDN-6-DISCONNECT: Interface Serial0:13 disconnected from 02155915479 , call lasted 36 seconds
Mar 1 17:05:59 UTC: EVENT_FROM_ISDN: dchan_idb=0x623BA450, call_id=0x2E41, ces=0x1
   bchan=0xD, event=0x0, cause=0x10
Mar 1 17:05:59 UTC: EVENT_FROM_ISDN:(2E41): DEV_IDLE at slot 1, port 33
Mar 1 17:05:59 UTC: CSM_PROC_IC7_OC6_CONNECTED: CSM_EVENT_ISDN_DISCONNECTED at slot 1, port 33
Mar 1 17:05:59 UTC: Mica Modem(1/33): Link Terminate(0x6)
Mar 1 17:05:59 UTC: CSM(1/33): Enter csm_enter_disconnecting_state
Mar 1 17:06:00 UTC: EVENT_FROM_ISDN: dchan_idb=0x623BA450, call_id=0x2E41, ces=0x1
   bchan=0xD, event=0x0, cause=0x0
Mar 1 17:06:00 UTC: VDEV_DEALLOCATE: slot 1, port 33 is deallocated
Mar 1 17:06:00 UTC: Mica Modem(1/33): State Transition to Terminating
Mar 1 17:06:00 UTC: Mica Modem(1/33): State Transition to Idle
Mar 1 17:06:00 UTC: Mica Modem(1/33): Went onhook
Mar 1 17:06:00 UTC: CSM_PROC_IC8_OC8_DISCONNECTING: CSM_EVENT_MODEM_ONHOOK at slot 1, port 33
Mar 1 17:06:00 UTC: CSM(1/33): Enter csm_enter_idle_state
CE Router Details:
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4(25a), RELEASE SOFTWARE (fc2)
CE External Modem: Paradyne3920
chat-script:
ABORT ERROR ABORT BUSY ABORT "NO ANSWER" "" AT&F\\D1\\Q3M0&D2&R0&S1S55=1S0=2&W OK "ATDT \T" TIMEOUT 60 CONNECT \c

Remote access sample configuration

Hi,
i have a 3825 router with a NM-12DM (digital modem), and i want to configure remote access on it.
Can some body give me a link for a sample configuration ?
Regards

Howdy,
The following link has a great simple config that should enable you to get started:
http://www.cisco.com/en/US/customer/products/hw/routers/ps274/products_configuration_example09186a0080094691.shtml
Hope that helps.
Pls remember to rate posts.
Regards,
Paresh.

How to save config changes on the MICA Modems for a 3640

Hi!
I have a NM-6DM with MICA modems. While fine tunning the modem I changed some values which now I want to save. I have tried the at&w, at&w1 and at&w2 but I keep receiving ERROR.
Any help
thanks,
Mario S.

To configure any modem that is connected to a
Cisco router (whether an internal or external one),
always use a modemcap and "modem autoconfigure".
http://www.cisco.com/en/US/tech/tk801/tk36/technologies_tech_note09186a008009491b.shtml#configmodems
Cheers,
Aaron

Snow Leopard and GSM Modems (Vodafone)

I'm not sure if this is the proper place to post this, but I'd like to share my experience with GSM (GPRS/3G) modems and Mac OS X. The main reason for doing this is the fact that I wasn't able to find any related information for my issues on the web and I think I'm not the only one with those issues. Feel free to post any feedback here
Few months ago I started using a 3G modem with my Macbook Air. The service provider is Vodafone and the modem is incorrectly marketed by Vodafone on the web as a Huawei device (E169), but it is a ZTE K3656-Z modem (I'm not sure if the companies are different or if the hardware is, in fact, different, but the kernel module is definitely different :D).
The first thing that annoyed me is the Vodafone Mobile Connect application. The 'response time' between plugging in the modem and actually getting online is quite big, and I really wanted to get it out of my way. I'm not using any SMS functionality, so from my point of view, the application was totally pointless. When you plug in the modem, it acts as an external CD Drive. If the Vodafone Mobile Connect application is installed, it will automatically eject (unmount) the drive. Unfortunately,
this usually (not all the time, but quite often) generates a crash in diskutil (quite annoying).
But what annoyed me the most, was the fact that, when online, the Vodafone application was taking at least 35% of my CPU. Now, this is unacceptable Under normal load (Safari, Adium), this was quite acceptable. But under slightly higher load, the CPU was getting quite hot, causing the kernel_task to try to slow down the system (and cool down the CPU) by taking about 135% of CPU (according to Activity Monitor) and making the system unusable. Of course, another side effect was the cooler running at 6400 RPM, faster battery drain and generally, making the system quite unusable. My 1st Generation Macbook Air wasn't able to deal with all that
When I first saw the high CPU usage by the Vodafone application, I immediately thought of the old 56Kb WinModems Back then, it was quite a common practice to develop modems that would use the CPU to compress/decompress or process the data/sound in order to make the modem as cheap as possible, but inflicting a huge system slow down - Yes, I'm that old :P
Given that experience with those modems, I figured that the Vodafone application was somehow doing that as a 'user space module' Boy, was I wrong
So, this is what I did: First of all, you need to properly identify the GSM modem. In order to do this (no Terminal involved) is to set up connection using Vodafone Mobile Connect, then using the System Preferences, head over to Network and check the available interfaces (no, this is not a tutorial, but a guide :P ). You should see either a Huawei Modem or ZTEUSBModem/ZTEUSBATPort. Keep in mind the modem you have, then disconnect. At this point, you need to use the Vodafone application to change the PIN settings on your SIM card. Use the application (Preferences -> PIN) and disable PIN check. Now you can safely remove the Vodafone application
The second step is to install the proper modules/drivers/kexts for this. You can either get them from the web (at this point, you already know what modem you have) or you can use the packages located inside the Vodafone Mobile Connect application installer. To do this, simply use 'Show Contents' of the installer, then locate the packages (pkg) inside the Resources folder for your modem (the names are quite clear :P). Install that package and you'll have the modem drivers installed on your system.
Once the modem drivers are installed, when you connect the GSM modem, the external CD Drive will 'mount'. Eject it and wait a little bit (few seconds) until the SIM card is initialized and the modem is available. Go to System Preferences -> Network and add a new interface using ZTEUSBModem (not ZTEUSBATPort). Set it up as a Generic Modem, GPRS Modem and configure it with your provider settings (APN, username, password). Set the dial up number as *99# (you can find a lot of tutorials on the web about setting this up - the tricky part was installing the proper modules and disabling the PIN check). You may now connect.
The downside of this is the fact that you need to manually eject the drive when connecting the modem, otherwise you won't get the modem functionality, no SMS functionality and no PIN security.
The upside is a very quiet system (the fan runs at 2400 RPM as opposed to 6400 RPM), a fast one (I can't see any noticeable slow down at all) and better battery life time.
I'm not sure what is the effect on other systems, but my 1st Generation Macbook Air was totally unusable after few minutes of online time. Now it works perfectly
I really hope that this is useful for other people Feel free to ask any question, I'm aware that my 'tutorial' skills are quite poor :P

Oh, I forgot to mention: This works both on Leopard and Snow Leopard (tested on both systems). I've used the modem drivers located inside the Vodafone Mobile Connect installer (I couldn't find any ZTE modem drivers on the web).

How can I Create a Client Configuration File for RemoteApp and Desktop Connection with Server 2012?

I have a working RDS RemoteApp site and looking to test out the feature in Windows 7 Control Panel\All Control Panel Items\RemoteApp and Desktop Connections
I came across this link: Create a Client Configuration File for RemoteApp and Desktop Connection and I believe this is what I need to do first, but these instructions are for
Server 2008, and I'm running 2012.
Any suggestions or tips on how I can begin testing this with Server 2012?

Hi,
You can manually enter the path to the 2012 feed and it will connect and download the RemoteApps and Desktop connections.
If you need a sample .wcx file I have posted one here a couple of times. If you want I will look for it and post a link.
-TP
I tried adding my URL's below, these are sample links that work for me right now for when I log into the web page, but neither of these work. And I'm not sure what I would need to do with or how to create a .wcx file.
When I type in my URL of: https://connect.mydomain.org/RDWeb, I get redirected to:
https://connect.mydomain.org/RDWeb/Pages/en-US/login.aspx?ReturnUrl=/RDWeb/Pages/en-US/Default.aspx

Sound Blaster Omni 5.1 - mute speaker and mic with single button push

Does anyone know if its possible configure the Omni to mute both speakers and the Omni's internal mic with a single button push using the hardware volume/mute button on the Omni. I have a scenario where i need to mute both quickly when a call comes in and its a nuisance having to mute the speakers and mic separately.

Hi Tony,
Unfortunately there is no physical button to achieve that. Neither is there a software button to disable both speakers and mic at the same time.
Regards,
Colin-CL

New notebook only has headphone out and mic in -- Will any Creative speakers work?

Hello all: My new notebook only has a headphone out and mic in, and no audio out as you see on desktop PCs. I prefer not to use my USBs as I have other devices using them. Are there any Creative speakers which can use the headphone output and convert it to line level? This is a frustrating problem...the product specs all assume that you have a line level output 1/8 stereo jack. I don't. How can I find out which Creative products (if any) will work? I have a very typical, Compaq V6000 notebook running XP. I'm looking to spend under $80 and would prefer a 2 speaker or 2 pc w/ subwoofer configuration. I prefer to know that I can connect my new speakers rather than order blindly. Thx yall.
Message Edited by brg500 on 07-17-2007 07:25 PM

You can perfectly connect your 2.0 or 2.1 speakers to the headphones out, because it's like it was a line out, with the only difference that you can modify the out volume. There's no problem at all.

Need a sample configuration

Folks,
I wrote a small program to parse the configuration. I am looking for a sample configuration of a Edge Router ( preferably 7200 ) having lots of configuration data including VPN , Martini Tunnel etc. I need to test my parser.
Any help will be greatly appriciated.

And....I am looking for a sample program to parse...could you help me...

Configuration between SAP PI and BPM in SAP PO

Dear Experts,
I am working on SAP PO 7.31 and want to carry out configuration between SAP PI and BPM in SAP PO. I carried the post installation
activities in NWA i.e. CTC.
Helplessly , I could not find any documents and notes to refer the configurations.
Regards
Rebecca

AAEx configuration:
Advanced Adapter Engine Extended (AEX) - Installation and Configuration - III
Configuring SAP BPM and PI runtime:
Configuring Message Processing from PI to BPM - Process Orchestration - SAP Library
Sample BPM
NetWeaver BPM for System-to-System Message Orchestration (Including Migration of ccBPM to NW BPM)
Hope this helps

Configuring WCCP for http and https

How do I configure wccp on a 6509 to redirect http and https trafic to a S650. I am using the following config and http is working fine:
ip wccp version 2
ip wccp web-cache redirect-list aclwccp
interface Vlan23
description Rede Firewall
ip address 10.0.23.20 255.255.255.0
ip access-group 172 out
ip wccp web-cache redirect out
mls rp vtp-domain coc_block1
mls rp ip
mls netflow sampling
end
Should I config an other service for the https protocol?

Cecato,
The WSA can be configured to send 80 and 443 traffic, in the WCCP settings area (5.2.0+). There are some things you will need to be aware of before doing this though:
1. If you are on 5.2.0-x, you will not be able to inspect HTTPS traffic. Only version 5.5.0+ has the ability to decrypt HTTPS traffic. Because of this, it is not recommended to redirect port 443 on WSA version 5.2.
2. You will most likely need to specify a service ID other then web-cache. On most Cisco devices, web-cache is reserved for port 80 traffic only and cannot be changed. Any other service ID will work as you want it to.

Sample Configuration vor PRI (E1) and MICA Modem

Similar Messages

Maybe you are looking for