Screen "SAPMJ1IFN" 1110 could not be generated.

Hi,
I'm creating sub contracting challen tcode J1IF01.
Here i'm getting runtime error is Screen "SAPMJ1IFN" 1110 could not be generated.
Please guide me where i'm mistake in Sub Contracting.
Regards,
Balakrishna G

Hi Sabu,
The problem is caused by your customizing include, most probably the one in table QMEL.
Field ZZMTART has been created before in one of these CI structures, but some how was deleted it at later stage.
.INCLUDE     CI_QMEL
.INCLUDE     /SAPSMOSS/ATTRIBUTES
.INCLUDE     CLAIM_MANAGEMENT
One way to solve the issue, is by recreating this field again in the customizing include. Or you take it out from the screen enhancement of transaction IW21. You can check the screen enhancement in CMOD. Customizing include changes and screen enhancement changes better to be done after office hour, as the activation normally takes quite some time, and will cause short dump if users are running transaction which tables has the customizing include.
Regards,
Lim...

Similar Messages

  • Runtime error Screen "SAPLXQQM" 0100 could not be generated.

    Hi All,
    I have one issue with IW21 transaction code( Create PM Notification: Initial). When I'm trying to crteat a Notification of type L1( GEBS LEV PM request ), its going to dump showing the runtime error as,
    "At the screen generation it was detected that a screen to be generated has a syntax error or could not be generated due to another error."
    Error analysis
        Screen "SAPLXQQM" 0100 could not be generated.
    Trigger Location of Runtime Error
        Program                               SAPLXQQM
        Include                                 LIQS0O90
        Row                                     20
    I'm using ECC 6.0 version.
    When we do syntax check of the progran or screen it is showing syntax error " Field VIQMEL-ZZMTART is not in the data Dictionary'.
    Please help me in this.
    Thanks & Regards,
    Sabu.

    Hi Sabu,
    The problem is caused by your customizing include, most probably the one in table QMEL.
    Field ZZMTART has been created before in one of these CI structures, but some how was deleted it at later stage.
    .INCLUDE     CI_QMEL
    .INCLUDE     /SAPSMOSS/ATTRIBUTES
    .INCLUDE     CLAIM_MANAGEMENT
    One way to solve the issue, is by recreating this field again in the customizing include. Or you take it out from the screen enhancement of transaction IW21. You can check the screen enhancement in CMOD. Customizing include changes and screen enhancement changes better to be done after office hour, as the activation normally takes quite some time, and will cause short dump if users are running transaction which tables has the customizing include.
    Regards,
    Lim...

  • Code could not be generated because an external component or driver is missing

    Greetings All,
         I've using Labview for a little over a year and I have an interesting situation with regards to Labview that I came across today.  When I left off yesterday (01/11/12) my TestStand sequence was compiling fine.  Today for some reason the compiler told me that one of the VI was broken or missing a sub vi.  When I made my way through all the sub vi's in the vi that seemed to be a problem I came across "Code could not be generated because an external component or driver is missing".
         The problem started on the computer (NI PXI-8101 with WinXP and Labview 2010) located in a PXI-1044 that is in my Test Stand.  I have a complete backup on my laptop and my desktop computer which both compiling successfully with no errors.  I tried installing the directory on another PXI-8101 and got a different set of results.  The first PXI-8101 gave 100+ errors in TestStand pointing to one of my vi's and the other PXI-8101 reported only one (1) error.  The vi is basically using DAQmx vi's to create a "write to one line" action.  I'm kind of stumped as to why it works on the laptop/desktop and not the PXI computers.  All four computer are WinXP professional and Labview 2010.  I saw somethings through google search engine but nothing conclusive.  I'm hoping that someone can give me an explaination as to what is causing the error as described.  Even if I copy over the directory it doesn't fix the problem.  Thank you in advance for an information you provide with this rather interesting problem that I've encountered.  If you require addition information let me know.
    Regards,
    Scott
    Solved!
    Go to Solution.

    Greetings Beau,
         Thank you for the reply.
         I loaded the offending VI into Labview (2010) with TestStand inactive.  Of course this was after I completely shutdown the computer and re-booted to ensure that nothing was resident in memory.  I've included a couple of the error list boxes in this post. 
         It comes down to a subvi that is two (2) subvi's deep.  All these vi's are doing is commanding a write or read to and from the PXI-6509.  When I check the VI at the level that has no broken run arrows (named below), nothing in the block diagram looks out of place as it should since these were installed by Labview installation.  The vi that uses these vi's looks total normal and its block diagram doesn't have anything out of the ordinary yet the run arrow is broken.  The odd part of this is that the top of the window that states the filename of the vi has an astrex at the end of the filename, even though nothing has changed in that vi.  
    Here is a list of the deepest level that has no broken run arrow:
    DAQmx Create Channel (DI-Digital Input).vi
    DAQmx Start Task.vi
    DAQMX Read (Digital Bool 1Line 1Point).vi
    DAQmx Clear Task.vi
    DAQmx Create Channel (DO-Digital Output).vi
    DAQmx Write (Digital U8 1Chan 1Samp).vi
         I guess the real question is what is the error message ("External component or driver missing") really telling me if all of the vi's look right.  I appreciate any information you can send my way that will give me a better understanding of where this error is coming from.  The program I developed had been running without a hitch for a month an all of sudden crash.
    Thank you for your time in this matter.
    Scott
    Attachments:
    Write to one port broken VI error list.JPG ‏47 KB
    Readfrom one line broken VI error list.JPG ‏46 KB
    Broken_VI_Error_Screen.JPG ‏56 KB

  • Hi , I would like to ask you about purchase item transfer to ipad from mac book Itunes, But This message will be notified on screen this ipad could not be synced because this computer is no longer authorized with that purchased item on this ipad.

    Hi ,
    I would like to ask you about purchase item transfer to ipad from mac book Itunes, But This message will be notified on screen
    "This ipad could not be synced because this computer is no longer authorized with that purchased item on this ipad"
              I did authorized in the store, but still did not transfer to the mac. Could you please to tell me what should I do it? Please let me know that as soon as possible.
    Regards,
    Thank you

    The iPad is fine.  But the computer you're syncing with needs to be authorised with the Apple ID that was used to buy the material on the iPad.  You do this by picking the 'Authorize' item from the menu in iTunes and entering the account name and password.

  • Error: Object type '' could not be generated when creating sales order

    Hello Friends,
    I am using a SAP standard ITS service to create sales order.
    When I am creatin SO, it gives me error Object type '' could not be generated.
    Can you plz suggest me what is that issue & how I can reslove it.
    Regards,
    Narendra

    any inputs around this plz??

  • My iPod is showing a white screen. I could not see anything. But I can listen to songs by blindly pressing the play button twice. The battery comes only for an hour.? How do I get the display and longer battery?

    Hello Friends,
    I've two iPod Nanos (4th gen - 8GB). I'm facing a severe problem with both of them. For both iPods, I tried to do this method Simultaneously press the top button + home (central) button. But of no use.
    1. My first iPod is showing a white screen. I could not see anything. But I can listen to songs by blindly pressing the play button twice. The battery comes only for an hour.? How do I get the display and longer battery?
    2. My second iPod is facing more severe problem. None of the buttons are working. When I connect it my PC it showing "CONNECTED- eject before disconnecting". But it is not ejecting with all the usual methods. When I manually and physically disconnect it from the PC the same "CONNECTED- eject before disconnecting" is still showing till the battery goes off. After that if i press any button it is showing low battery signal. And when i re-connect it to the PC the same process is repeating. When I tied to restore it to the factory settings I'm getting "Error" report.
    (I'm using windows 7)
    Friends, Please help me with the above problems. It will be a great help.
    Thank You.
    R.SAMALA

    Sounds like some hardware issues, meaning you'll want to take or send the iPods in for service or repairs. You can choose to have Apple do an out of warranty exchange for the prices indicated in the link below or find another third party service perhaps even local to your area.
    http://www.apple.com/support/ipod/service/prices/
    B-rock

  • "Some updateing commands could not be generated ....." error

    Hi all,
    I am accessing an Oracle server on which I have READ ONLY rights. I am trying to create a DataSet. When I do so, I get an error:
    Some updating commands could not be generated automatically. The database returned the following error:
    This object has been deleted.
    1) Is this just because my access is readonly?
    2) A different message might be preferred ("code to submit updates was not created due to limited user rights" or some such.
    3) Can I use this even with the error or will I have other problems because the process did not complete correctly?
    Thanks,
    JustMe

    Can't remember how I solved this, but it is solved.

  • Posting rule for assembly order for item 000000 could not be generated

    Hi all,
        While creating production order from sales order system giving an error message 'Posting rule for assembly order for item 000000 could not be generated.'
        Kindly help to resolve the issue.
    SmanS

    Dear SAP PP Consultant ,
    What is the strategy group you are maintained in the material master ?

  • Some backend documents could not be generated or are incorrect - Contract

    Hi SRM Experts,
    I am trying to create Contract with Carry out Sourcing and reference to Shopping Cart. But, I am able to create Contract with Error like "Some backend documents could not be generated or are incorrect". Please let me know do I need to do any configuration settings or implement OSS Note to fix for my problem.
    Kind Note: System is not updating Purchasing Organisation and Purcgasing Group at Contract Header Level. I treid to use BAdI (change BAdI) to update Organisation details - got Organisation details from Shopping Cart and updated in Contract change BAdI (Org Structure).
    SRM Version: 4.0 with Extended Classic scenario.
    Thanks a lot in advance for your help.
    Thanks,
    Sudarsan

    Hi Muthu / SRM Gurus,
    I removed BAdI implementation for Contract. I am still gettign error message.
    When I create contract from Carry Out Sourcing I am geeting error message "Some backend documents could not be generated or are incorrect" and when I create contract with Process Contract I am not getting any error.
    Can anyone guide me or suggest me to fix this issue?
    Thanks a lot in advance.
    Thanks,
    Koyya

  • Compile error (Code could not be generated)

    When I try to run the attached vi I get the following error message "Code
    could not be generated correctly for this VI."
    I use Labview 7.1 under Windows XP.
    Attachments:
    ParSettings.zip ‏293 KB

    The "Representation" enum is defined differently in the "SDO Par In", "SDO Par", PDO Par In" and "PDO Par" clusters. Labview does apparently not recognice this and crashes instead of warning for incompatible data types.

  • Simulation Loop: Code could not be generated correctly for this VI

    Running LabView Simulation 8.2 on Windows XP laptop.  I have a Simulation Loop that keeps generating the following error message:
    "Simulation Loop: Code could not be generated correctly for this VI"
    The only reference I can find in my searches is to using an RTX target, which does not apply.  When I click on Show Error it just highlights the Sim Loop
    Any ideas on how to debug this?

    Perhaps you can start removing things until you don't get the error any more. How big is the code in the loop?
    Mike...
    Certified Professional Instructor
    Certified LabVIEW Architect
    LabVIEW Champion
    "... after all, He's not a tame lion..."
    Be thinking ahead and mark your dance card for NI Week 2015 now: TS 6139 - Object Oriented First Steps

  • Report RV13ANAH could not be generated

    Hello Experts,
    I have one issue.  In VK13, I give the condtion type and click the Condition information button.  I get the error as Report RV13ANAH could not be generated.  The program RV13ANAH has syntax error which I found out.  The error is table A902 doent have a field KFRST and KBSTAT.  But the program has these two fields in the SELECT statement
      SELECT * FROM A902 into table t_A902
        WHERE KAPPL =  KAPPL
          AND KSCHL =  KSCHL
          AND AUART_SD IN F001
          AND VKORG IN F002
          AND KUNNR IN F006
          AND KFRST IN F007
          AND KBSTAT IN F008.
    I need to remove these two fields from the program.  But i believe this can be done only by generating the table or access or access sequence or doing some settings in the customizing.  I do not know what exactly to be done.  Could anyone please let me know what needs to be done.
    Cheers,
    Balaji

    Hello Venkatesh,
    In KE4A, I dont get 902 table at all.  any other clue.
    Cheers,
    Balaji

  • Screen sequence number could not be determined

    Hi, All,
    After client copy, I ran MM03, but got an error as below:
    screen sequence number could not be determined.
    How to solve it?

    You need an ABAPER to debug the issue. Also check the logs for more details
    Regards
    Juan

  • BLACK SCREEN stating "windows could not start because the following is miss

    I installed Bootcamp update 2.1 and then XP SP3.
    Now when I start up my Mac I am getting a BLACK SCREEN stating "windows could not start because the following is missing or corrupt: <windows root>\system 32-hal.dll Please re-installl a copy of hte above file"
    I tried to use the option key and insert the Windows CD but it won't start up.
    Also, when I start up I must use the option key and select the Mac OS and it will start up and everything is fine there. Advice appreciated.

    Did you ever solve this? I had updated to BC 2.1 (After updating Apple Software Update al on the Windows side) I waited & just tonight tried to install SP-3. It appeared to install & When I was prompted to restart--I also got the black screen. Mine said:
    Windows could not start because the following file is missing or corrupt:\Windows\inf\biosinfo.inf
    You can attempt to repair the file by starting Windows setup using the original setup CD-ROM. Select ‘r’ at the 1st screen to repair.
    I just force powered off & booted into Mac.
    I think I need to restart my Mac into Windows (using the Option key ) WHILE THE WINDOWS XP CD is in the optical Drive. Then maybe I’ll get a choice to select ‘r’ to repair at the 1st screen?
    You may need to do essentially the same thing. I do not know if this problem is a boot camp problem of just a Windows problem.
    Sure is annoying,
    Good luck!

  • "The PDF could not be generated"

    I need to download a page to my hard drive and when I click "Printer-friendly Version" I get the a pop-up box with the message, "The PDF could not be generated".
    That's it. Any ideas?
    Thanks.
    Staten.islander

    Got a link to the site that has the PDF? Sounds like it's being dynamically generated but there could be something wrong.

Maybe you are looking for